随钻声波测井隔声体刻槽影响的数值模拟研究*

针对随钻声波测井中钻铤波干扰以及刻槽后散射波问题，该文 利用时域有限差分法模拟钻铤波在随钻隔声体中的传播规律，首先考察在无限大流体中钻铤波在凹槽分界面处的散射特征，利用波场快照直观显示了钻铤波会有一部分能量在刻槽的固液界面转化为斯通利波。同时在有地层时分别对比了均匀内刻槽和外刻槽对钻铤波的衰减效果，发现在选择均匀内刻槽还是外刻槽时结果不仅与频率范围有关，而且与刻槽的深度也有关系。最后对比了槽宽较大的均匀凹槽隔声体和槽宽较小的渐变凹槽隔声体。可以得出结论，在设计随钻隔声体时，在10 kHz以下选择均匀外刻槽方式相对于内刻槽隔声效果会更好。随着刻槽槽深增加，外刻槽在10 kHz以下相比于内刻槽隔声性能优势更加明显。渐变刻槽在满足衰减钻铤波幅度要求的同时，散射波对后续地层波和斯通利波影响也更小。     

周期性轴对称凹槽结构隔声特性数值模拟

提出一种在钻铤上切割周期性轴对称凹槽方式构建隔声体,消除钻铤模式波的方法.结果表明,其隔声效果与凹槽深度H、长度L、凹槽数目N、凹槽截面形状以及钻铤壁厚有关.选择矩形截面凹槽、减小钻铤壁厚、增加凹槽深度都可有效提高隔声体的隔声效果,该结构最高可获得约36 dB的声衰减,基本满足随钻声波测井仪器对隔声效果要求.     

软地层随钻测井仪器偏心情况下低频四极子源 激发波场的数值分析*

为了探索测井仪器偏心对随钻低频四极子波场的影响,利用有限元法(多物理场耦合有限元软件包)对软地层井孔中随钻仪器偏心情况下低频四极子声源激发的波场进行了数值模拟。通过对随钻四极子测井波形的分析可知,当采用低频随钻四极子偏心声源激发时,测井波列中除传播速度与低速地层横波速度相当的地层四极子波模式外,还存在一个幅度非常低、传播速度略高于井孔流体中声速的模式波,该模式被对应钻铤弯曲波模式,且该模式波的幅度随着随钻四极子源偏离井孔中心距离的增大呈二次方规律增大,地层四极子模式波幅度呈三次方规律增加。     

随钻新型隔声体的声学性能研究*

近年来,随钻声波测井成为了一种新兴的勘探方式,但是在勘探过程中产生的钻铤波会影响地层信号的提取。如何能够更有效的提取地层信号,成为学者研究的重点课题。本文基于声子晶体理论设计了一种新型隔声体,相对于传统刻槽结构能够更好的压制钻铤波。首先基于周期结构理论,利用有限元软件COMSOL MUTIPHYSICS计算了不同刻槽结构的能带图,相比于传统刻槽结构,新型隔声体有更宽的带隙,说明新型刻槽结构可以更有效的阻隔钻铤波。接着在测井模型中对刻槽结构进行频响函数曲线的计算,验证了新型刻槽结构隔声效果在所计算频率范围内优于传统刻槽结构。然后分析了在能带计算和频响曲线计算下隔声效果最好的声源频率(17kHz和22kHz)时新型刻槽结构的STC(时间慢度相关法)处理对比,最后对比声源频率17kHz下新型刻槽结构和传统刻槽结构的STC信号处理,发现此声源频率时新型刻槽结构可以更好的提取地层折射纵波和横波。     

钻具遇卡声波检测理论与实验研究*

石油钻探过程中,钻具经常发生陷入泥沙中不能自由活动进而卡在井下的事故。本文提出使用单发双收声系来检测钻具遇卡的方法,首先使用有限差分模拟了钻具外为自由流体和泥沙两种介质时的钻铤波响应,通过对比远近接收器的钻铤波衰减,发现泥沙卡钻情况下的钻铤波衰减要明显大于自由钻具情况。随后建立了实验模型对理论结果进行了验证。理论模拟与实验结果均表明声波方法可用以检测钻具遇卡事故,从而确定卡钻的深度位置,为解卡钻作业提供解释依据。     

有效测量套管井泄漏Lamb波衰减的实验研究

低密度水泥在油气井中的广泛应用使得常规的声阻抗类测井方法难以准确、有效地评价固井质量,而声波倾斜入射在套管中激发的弯曲型Lamb波对水泥的性质及胶结情况具有很高的分辨能力,能够很好地解决低密度水泥的固井质量评价问题。弯曲型Lamb波对套管后介质声学信息的响应反映在声波衰减中,因此该文通过实验研究了激发弯曲型Lamb波的有效方式,分析了声波入射和接收角度对Lamb波衰减的影响。实验结果表明,入射和接收角度在一定范围内变化时,虽然激发出的Lamb波模式均为弯曲型Lamb波,但在同一套管模型下测量的声波衰减值会有差异,选择激发弯曲型Lamb波的最有效方式,计算得到的Lamb波衰减对套管后介质的灵敏度才会最高。     

弹性波数值模拟系统

弹性波数值模拟是石油测井仪器设计、研发和制造的有效工具,其有助于优化仪器的换能器频率、发射与接收器间的源距、接收器的个数及间距、隔声体的结构,也可帮助理解特定声源在复杂环境中的声传播规律及正确认识和评     

利用井中偶极弯曲波反演渗透率的影响因素及灵敏度分析

本文以各向同性饱和流体孔隙介质充液井孔中声场传播理论为基础,系统考察了影响偶极弯曲波特征的主要因素,分析了快慢地层条件下弯曲波衰减和速度对不同参数的敏感度,对比结果表明,弯曲波的速度基本不受地层渗透率的影响,其衰减对渗透率的敏感性要远高于速度。弯曲波中心频率会随着波的衰减而发生偏移,说明利用弯曲波衰减和频移特征联合反演地层渗透率是可行的。通过对比快慢地层下的弯曲波衰减和速度灵敏度曲线,发现在慢速地层中反演渗透率的结果要好于快速地层。同时,本文也指出在低孔低渗储层中,还可以考虑利用弯曲波衰减识别气层。     

套管中模式波的响应特征*

在固井质量评价中主要利用套管中模式波的幅度或衰减变化反映水泥的胶结状况,不同测井仪器在套管中激发的模式波的类型不同,研究套管中各模式波的传播特征和影响因素可充分挖掘测量数据的潜在应用价值。CBL和SBT等测井仪器在套管中主要激发拉伸波,类同于平板中的零阶对称Lamb波,水泥环封隔测井仪器的斜入射模式在套管中主要激发套管弯曲波,类同于平板中的零阶反对称Lamb波,垂直入射模式激发套管共振波,类同于平板中的高阶对称Lamb波。该文重点分析了这些模式波的衰减特征及其对微环的响应,套管弯曲波在套后耦合轻质水泥时对微环不敏感,但在套后耦合常规水泥或重水泥时,其衰减明显高于胶结良好的状况;拉伸波对微环的存在最为敏感;套管共振波对微环不敏感。     

套管中泄漏弯曲型Lamb波的传播特征

低阻抗水泥固井质量检测是油气田生产亟需解决的问题。套管中传播的最低阶泄漏弯曲型Lamb波(以下简称为A0弯曲型Lamb波)对套管后介质尤其是低阻抗水泥的声学参数和胶结状况具有很高的敏感性。通过建立多层介质模型,从理论上计算了其频散和衰减与套管后介质属性及水泥环第Ⅰ界面胶结状况的关系,并数值模拟了有限尺寸定向辐射探头激发和接收的全波波形。结果表明,在套管后耦合慢速水泥时,A0弯曲型Lamb波的频散曲线存在断点,曲线分为两个分支;A0弯曲型Lamb波的衰减在套管后耦合慢速水泥时最大并且对水泥环第Ⅰ界面胶结差时流体环厚度有很高的灵敏度,利用其衰减可以实现对套管后介质类型、水泥环第Ⅰ界面胶结状况及窜槽厚度的有效判别。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.