用有限元/边界元方法进行结构声辐射的模态分析

采用有限元方法和边界元方法建立了轻流体介质中复杂结构振动声辐射的模态分析模型,可计算结构的模态辐射效率、场点声压、结构辐射声功率和辐射效率等声场特性参数．文中以板和加筋板结构的振动声辐射为例进行了模态分析,并与用远场 Ｒａｙｌｅｉｇｈ积分计算所得结果进行了比较．研究了激励力作用位置对板结构声辐射的影响和加筋板与板的模态辐射效率特点,并指出板加筋后会改变板的模态辐射效率规律．     

降低加肋双层圆柱壳辐射噪声线谱的结构声学设计

为降低双层圆柱壳辐射噪声线谱,从控制内壳振动响应和衰减壳间振动传递率进行结构声学设计。采用机械阻抗理论分析了环肋圆柱壳模态响应控制机理;由环肋振动方程推导分析了环肋径向机械阻抗特性;基于阻抗失配、波形转换原理提出一种阻抗加强环肋,分析了振动波阻抑特性;利用阻尼减振技术,综合考虑肋板的刚度、阻尼特性,设计了金属橡胶层叠肋板;结合数值计算实例,分析了设计双层壳模型的声辐射性能。结果表明:设计的双层加肋圆柱壳结构能有效降低辐射噪声线谱,在分析频段内辐射声压线谱平均降低约6.6 dB。研究结果对研制低噪声水下航行器具有良好的工程价值和应用前景。     

高效半解析方法分析周期正交加筋板的振动-声辐射特性

为了对水下无穷大双周期正交加筋板结构模型在简谐面力激励下的振动响应及声辐射特性进行更为合理的理论预测与分析,建立了加筋板结构的数学模型。结合傅里叶变换、泊松迭加公式及空间波数法,将周期加筋板的振动响应及辐射声压表达为关于结构位移谐波分量的函数方程,对加筋板模型提出了高效分析求解方法并进行了谐波分量截断求解。验证了方法的正确性,并分析了结构的振动特性以及加强筋周期间距和扭矩对辐射声压的影响。结果表明,加强筋的扭转作用影响加筋板结构的振动模态频率,对于较高精度要求的工程应用,加强筋的扭转作用不能忽略。通过调节加强筋周期间距及横截面尺寸,可以降低薄板在较低频域区间的远场辐射声压。      

任意边界板结构的声辐射模态误差传感器的设计

获取声辐射模态伴随系数是基于声辐射模态理论进行主动结构声控制(ASAC)的重要环节。以往PVDF分布式传感器的设计难点是振速展开受边界条件的限制,其设计过程往往是针对特定边界条件展开的。本文在声辐射模态理论和两维分布式传感器的压电方程的基础上,将板表面振速分布用Legendre多项式展开,给出了两维板结构的PVDF传感器形状与边界条件无关的设计方法。这样设计得到的传感器能应用于任意边界条件和任意振速分布的两维板结构,且实时性好,拓宽了其应用范围。本文还分别以固定边界条件板及在该板中任取一小区域两种情况为例,证明了该设计方法的可行性。     

水中有限长加肋圆柱壳体振动和声辐射近似解析解

加肋圆柱壳体是水下航行器的主要结构形式。将肋骨对壳体的作用简化为只有法向力,本文导出了水中有限长加肋圆柱壳体的振动和声辐射的近似解析解。其中肋骨的作用表现为在无肋的耦合振动方程中增加附加阻抗,因此壳体的振动和声辐射由壳体的机械阻抗、流体的辐射声阻抗和肋骨的附加阻抗所决定。数值计算例子表明,在低频情况下,加肋对辐射声功率影响不大,但将降低表面平均振速,从而增加声辐射效率。     

覆黏弹层加肋双层板的声反射

为评估覆盖层的吸声性能,研究黏弹层在无限大周期加肋双层板背衬下的声反射。首先通过弯曲波与Lamb波的比较,揭示了板近似理论不适用于黏弹性板的原因。为此采用(黏)弹性理论处理(黏)弹性板,而肋板的处理则采用板近似理论,并用Hull提出的方法解决肋板和平板的耦合问题,得到反射声场的解。与板近似理论计算加肋双层板声反射的结果进行比较验证了本文方法的正确性,对反射系数进行计算分析了背衬对声反射的影响,定义平均反射系数比较了不同覆盖层的性能。结果表明,频率较低时覆盖层无法有效抑制背衬的影响,板间流体层与双层板的耦合作用引起共振散射,肋板与双层板的耦合作用降低声反射。     

强弱耦合板-腔系统的声辐射模态计算与分析EI北大核心CSCD

针对板-腔耦合系统的声辐射模态(ARM)计算问题,提出了一种基于能量原理的声辐射模态计算方法,该方法从能量原理的动力学方程构建起声压模态幅值和结构模态幅值的关系,通过将声势能表示为结构模态幅值向量的二次型形式,得到板-腔耦合系统的声辐射模态,弥补了前人理论在解决声腔为阻抗壁面和结构-声为强耦合条件时的不足。通过数值算例验证了本文计算方法的正确性和有效性,在此基础上分析了壁面和结构-声耦合条件变化对声辐射模态特性的影响。结果表明:声辐射模态辐射效率曲线会在声腔模态频率处产生峰值,阻抗壁面的引入会降低声辐射模态辐射效率在峰值处的幅值,并且阻抗值越小,幅值衰减效应越明显,具体表现为声势能曲线在辐射效率峰值频率处幅值会下降;强耦合条件下低频段声势能响应主要由弹性板结构模态激发,响应峰值密度更高,幅值更低。低频同频宽的声辐射模态辐射效率峰值数更少,峰值频率更高。     

求解水中加肋板声辐射特性的虚拟声源法*

发展一种利用虚拟声源离散声场的方法求解加肋板在水中的声振耦合问题。由波叠加原理和单元体积速度匹配的原则,根据离散的结构单元满足的动力方程和结构与介质的交界相容性条件,确定虚拟声源强度,计算结构的声辐射功率。本文以简支矩形加肋板为例,在不获得结构表面振速和声压的情况下,计算了结构在水中的声辐射功率,并与解析方法计算的结果进行了比较,表明了该方法具有较好的计算精度。     

复杂双层壳体声辐射性能分析

研究了加肋的环板双层壳体的振动和声辐射性能,采用经典Flugge微分算子描述壳体的运动,通过将加强构件等效为反力和反力矩加在内外壳体的表面上而引入壳体振动方程,并利用Helmholtz波动方程和壳体表面的位移连续条件来解位于内层壳和外层壳之间的环形流场,最终建立和求解了双壳体声-流体-结构耦合方程,详细讨论了双壳体参数和双壳间连接型式的变化对其声辐射性能的影响。得出了以下结论:双层壳体内外壳间距减小,内外壳的耦合作用就越强,壳体辐射声功率和表面振动均方速度级升高,外壳的“屏蔽”作用就越不明显;内外壳厚度的改变对壳体振动速度级有较大的作用,对声辐射的影响不是很明显,厚度越大,振动速度级就越低。     

超声波空气污染物颗粒采样器的新结构及其特性研究*

超声波空气污染物颗粒采样器具有可采集低浓度颗粒污染物、采样速度快、重复性好、结构简单、易分析被采集物以及不破坏污染物成分等优点。为了进一步提高其采样效率,该文提出了一种超声波空气污染物颗粒采样器的新结构。该采样器由超声换能器、被粘接在换能器声辐射面上的圆形声辐射板以及与声辐射板平行的采样板组成。该采样器利用声辐射力和声学流场驱动空气中的污染物颗粒快速聚集到采样板上。样机测试表明,该结构在空气污染物颗粒初始浓度为4 mg/L以及辐射板中心位置的振动速度为0.29 m/s时,对烟雾中PM2.5和PM2.5-10颗粒的采样效率为16.3 mg/m~2·min·W。与不采用高阶弯曲振动圆形声辐射板的结构相比,其采样效率增加了110%。     

含损伤黏弹性阻尼加筋层合板声功率和指向性变异*

该文旨在研究损伤位置和程度对自由阻尼加筋层合板声辐射功率和指向性的影响。基于Mindlin和Timoshenko梁理论,建立了自由阻尼层合板-梁组合结构有限元模型。数值求解四边简支边界条件自由阻尼加筋层合板振动响应,继而通过Rayleigh积分计算加筋层合板辐射声功率和指向性。将计算得到的前4阶模态固有频率、声辐射功率与指向性与已有文献进行了对比基本一致,验证了数值模型的正确性。最后,详细讨论了损伤位置和程度对自由阻尼加筋层合板固有频率、振型、声辐射功率和指向性的影响,结果表明：随着结构损伤程度的增大,声辐射功率峰值向低频移动,在更多角度上出现明显的指向性;声辐射功率和指向性对损伤位置比损伤程度更加敏感。     

Coupled FEM/BEM for control of noise radiation and sound transmission using piezoelectric shunt damping

In this paper, we present a coupled finite element/boundary element method (FEM/BEM) for control of noise radiation and sound transmission of vibrating structure by passive piezoelectric techniques. The system consists of an elastic structure (with surface mounted piezoelectric patches) coupled to external/internal acoustic domains. The passive shunt damping strategy is employed for vibration attenuation in the low frequency range. The originality of the present paper lies in evaluating the classically used FEM/BEM methods for structural–acoustics problems when taking account smart systems at the fluid–structure interfaces.     

任意阵形水声换能器阵辐射声场计算

本文用边界元的方法计算了阵形任意的水声发射换能器共形阵的辐射声场。在详细研究了边界元方法基本理论的基础上，采用Pro／ENGINEER软件与ANSYS软件相结合来建立换能器阵的边界元模型，再用SYSNOISE软件计算其辐射声场和辐射阻抗。这种声场计算方法可用于发射换能器阵设计阶段对设计结果进行预报。     

Dynamic and acoustic response of bidirectionally stiffened plates with eccentric stiffeners subject to airborne and structure-borne excitations

An analytical method based on the modal expansion technique was developed to predict the vibro-acoustic response of both unidirectionally and bidirectionally stiffened flat panel. This paper presents the response to diffuse acoustic field (DAF) and turbulent boundary layer (TBL) excitations in terms of their joint acceptance. Numerical results for the dynamic and acoustic responses are compared with finite element method (FEM) and boundary element (BEM) results for stiffened panel with complex and eccentrically shaped stiffeners subject to point force excitation. A theoretical prediction of the transmission loss (TL) is also compared with laboratory measurements conducted on flat panels representing aircraft models as well as with hybrid statistical energy analysis (SEA)-FEM periodic model. The results confirm that the stiffened panel has the same acoustic response as the skin without stiffeners at frequencies where the structural wavelengths are equal to the spacing between the stiffeners. In addition, the transmission loss is lowered by the presence of the stiffeners at some particular region of frequencies below the critical frequency with respect to the unstiffened panel.     

A prediction of the acoustic field of a vibrating box by FEM-BEM

I.Mathematicalmodelofacousticfie1dByapplyingtheSommerfeldradiationcondihonThus,anacousticfic1disdescribcdbyHelmholtzformula.Byconsideringaficldpointinthearea,Helmholtzformulaisgivenbythefollowingthreeintegra1equations:(1)Theexternalintcgra1fOrmu1a'(2)Thcintcrnalintegralformu1af(3)Thesurfaceintegralformu1afwhcreP.isthesoundpressureonthcSsurface;rthedistancefrompointqtothee1ementsurfacedSiqtheficldpoint,tuthefrcqucncyoftheacousticradiation;pthedensityofthesurroundingmedium,vsthenormalvibrati…     

Acoustic radiation force on a rigid cylinder near rigid corner boundaries exerted by a Gaussian beam field

Acoustic manipulation is one of the well-known technologies of particle control and a top research in acoustic field. Calculation of acoustic radiation force on a particle nearby boundaries is one of the critical tasks, as it approximates realistic applications. Nevertheless, it is quite difficult to solve the problem by theoretical method when the boundary conditions are intricate. In this study, we present a finite element method numerical model for the acoustic radiation force exerting on a rigid cylindrical particle immersed in fluid near a rigid corner. The effects of the boundaries on acoustic radiation force of a rigid cylinder are analyzed with particular emphasis on the non-dimensional frequency and the distance from the center of cylinder to each boundary. The results reveal that these parameters play important roles in acoustic manipulation for particle-nearby complicated rigid boundaries. This study verifies the feasibility of numerical analysis on the issue of acoustic radiation force calculation close to complex boundaries, which may provide a new idea on analyzing the acoustic particle manipulation in confined space.     

Noise reduction analysis for a stiffened finite plate

This paper presents an analytical solution for the vibration and acoustic responses of a finite stiffened plate that is covered with decoupling layers and subjected to external excitation. The theory of elasticity is used for the decoupling layer, and the stiffened plate is modeled by the plate theory and Euler–Bernoulli beam equation. Equations are constructed by the boundary conditions at the plate/coating and coating/fluid interfaces. The problem can be solved by the proposed method in this paper. Test verification shows that a good correlation exists between theoretical and test results. Thus, the theoretical study in this paper is correct. Numerical results show that shear waves insignificantly affect the structural vibration level difference (VR) under low frequencies. The noise reduction of the stiffened plate covered with decoupling layers is greatly influenced by the decoupling layer loss factor. A failure region of the vibration level difference is present in the low frequency band of the decoupling layer. Furthermore, the thickness of the decoupling layer significantly affects noise reduction.     

Directivity calculation with experimental verification for a conformal array of underwater acoustic transducers

The radiation directivity of a complicated conformal array of underwater acoustic transducers is presented based on the boundary ＂element method. It includes the element directivity of each transducer, the natural beam pattern and the controlled beam pattern of the transducer array. At first, the boundary element model of the conformal array is built up, and then the boundary condition is exerted on the model according to the design and environment in which the transducer array is used, and the radiation directivity of the conformal array is calculated. An experiment has been done to measure the directivity in an anechoic water tank. The calculated and the experimental results are compared and analyzed. They are consistent to each other. It is shown that the boundary element method together with the detailed calculations is successful to simulate and predict the radiation directivity of an underwater acoustic transducer array.     

进一步改进边界元方法以克服振动声辐射计算中解的非唯一性

章利用基于三次B样条插值的边界元方法，对振动体外部声辐射问题进行了研究，对CHIEF法及其改进方法作了进一步的改进，提出在加权余量意义下，通过把内部Helmholtz积分方程与其对内点坐标取导后的方程式作线性叠加，在域外构作的一个小体积块上进行积分以形成补充方程，经与表面Helmholtz积分方程相结合，来求解任意频率下的声辐射问题，并以脉动球和摆动球作为算例，说明本提出的方法能够有效地克服在特殊频率处解的非唯一性问题。