椭圆偏振法测定在线Low-E玻璃的可见-近红外光学常数与膜厚

从在线Low-E玻璃光学机理出发,用椭圆偏振光谱仪对在线Low-E玻璃功能层和过渡层的可见-近红外波段的光学常数进行研究.测量了样品在三个不同入射角的椭偏参数,分别用Lorentz双振子模型和Cauchy模型来描述Low-E玻璃功能层和过渡层的光学色散特性.通过拟合椭偏参数获得在线Low-E玻璃的光学常数及每层膜厚度,并用扫描电镜对样品的膜厚进行表征.结果表明,Lorentz双振子模型和Cauchy模型能很好地解释在线Low-E玻璃的光学特性;同时,椭圆偏振法也为多层膜系统提供了一种测定光学常数和膜厚的可靠方法.     

ZnSe/SiO2复合薄膜光学常数与荧光光谱的研究

采用溶胶-凝胶工艺与原位生长技术，制备了ZnSe/SiO₂复合薄膜.X射线衍射分 析表明薄膜中ZnSe晶体呈立方闪锌矿结构.X射线荧光分析结果显示薄膜中Zn与Se摩尔比为1 ∶1.01—1∶1.19.利用场发射扫描电子显微镜观察了复合薄膜的表面形貌，结果表明复合薄 膜表面既存在尺寸约为400nm的ZnSe晶粒，也存在尺寸小于100nm的ZnSe晶粒.利用椭偏仪测 量了薄膜椭偏角Ψ，Δ与波长λ的关系，采用Maxwell-Garnett有效介质理论对薄膜的光学 常数、厚度、气孔率、ZnS 关键词： 2复合薄膜')" href="#">ZnSe/SiO₂复合薄膜 光学性质 椭偏光度法 荧光光谱     

椭偏精确测定透明衬底上吸收薄膜的厚度及光学常数

椭偏仪难以精确测量透明衬底上吸收薄膜光学常数的原因:1)衬底的背面反射光为非相干光, 它的存在会极大的增加拟合难度; 2)衬底光学常数(折射率和消光系数)的差异会影响测量的准确性, 而且会在吸收薄膜的光学常数中表现出来, 需要单独测量其光学常数; 3)厚度与光学常数之间呈现强烈的关联性. 针对以上三个问题, 选择石英玻璃、载玻片、盖玻片和普通浮法玻璃作为研究对象. 采用折射率匹配法消除上述衬底背面反射光的影响. 结果显示, 折射率匹配法能够有效消除折射率在1.43-1.64、波长范围为190-1700 nm波段的石英、浮法玻璃等透明衬底的背面反射光. 之后, 通过拟合椭偏参数ψ和垂直入射时的透过率T₀ 分别得到以上衬底的折射率和消光系数. 拟合得到的结果与文献报道的趋势一致. 最后, 采用椭偏参数和透过率同时拟合的方法(SE+T法)得到类金刚石薄膜(沉积在石英玻璃上)和非晶硅薄膜(沉积在载玻片、盖玻片上)光学常数和厚度的准确解.     

基于透射光谱确定溶胶凝胶ZrO2薄膜的光学常数

基于溶胶凝胶ZrO₂薄膜的紫外/可见/近红外透射实验光谱,采用Swanepoel方法结合Wemple-DiDomenico色散模型,方便地导出了ZrO₂薄膜在200—1200nm波长范围内的光学常数,包括折射率、色散常数、膜层厚度、吸收系数及能量带隙.研究发现,溶胶凝胶ZrO₂薄膜具有高折射率(1.63—1.93,测试波长为632.8nm)、低吸收和直接能量带隙(4.97—5.63eV) 等光学特性,而且其光学常数对薄膜制备过程中的重要工艺 关键词： 光学常数 Swanepoel方法 2薄膜')" href="#">ZrO₂薄膜 热处理     

N掺杂锐钛矿TiO2光学性能的第一性原理研究

用平面波赝势方法(PWP)计算了N掺杂锐钛矿型TiO₂前后的光学特性,即介电函数虚部ε₂(ω)，光学吸收系数I(ω)和反射率R(ω). 并从能带结构上解释了为什么掺N后锐钛矿型TiO₂的光学谱在2.93，3.56和3.97eV处相对掺杂前会出现3个峰值的原因. 从光谱图上分析得出，掺杂后TiO₂要发生红移现象，实验现象证实了这一结果. 关键词： N掺杂 2')" href="#">锐钛矿型TiO₂ 光学性能 第一性原理     

溶胶-凝胶法制备(Ba0.7Sr0.3)TiO3/LaNiO3异质薄膜及其结构和介电性质研究

采用改进的溶胶-凝胶方法在单晶Si(100)衬底上制备了介电性能优异的(Ba_0.7Sr_0.3)TiO₃/LaNiO₃异质薄膜.实验发现，在750 ℃下 、O₂气氛中晶化的LaNiO₃薄膜的电阻率最小.C-V与I-V特性测量表明(Ba_0.7Sr_0.3)TiO₃薄膜具有优异的介电性能，在频率为50kHz、零偏压下的相对介电常数ε_r>300，偏压为6V时漏电流密度J_L<1.2×10^-6A/cm². 关键词： xSr_1-x)TiO_３铁电薄膜')" href="#">(Ba_xSr_1-x)TiO_３铁电薄膜 ３底电极')" href="#">LaNiO３底电极 溶胶-凝胶法     

椭偏透射法测量氢化非晶硅薄膜厚度和光学参数

针对多角度椭偏测量透明基片上薄膜厚度和光学参数时基片背面非相干反射光的影响问题,报道了利用椭偏透射谱测量等离子增强化学气相沉积法(PECVD)制备的a-Si:H薄膜厚度和光学参数的方法,分析了基片温度T_s和辉光放电前气体温度T_g的影响.研究表明,用椭偏透射法测量的a-Si:H薄膜厚度值与扫描电镜(SEM)测得的值相当,推导得到的光学参数与其他研究者得到的结果一致.该方法可用于生长在透明基片上的其他非晶或多晶薄膜. 关键词： 椭偏测量 透射法 光学参数 氢化非晶硅薄膜     

椭偏光谱测量中椭偏参数的灵敏度分析

在对椭圆偏振测量的基本原理进行了简单介绍和推导后,讨论了椭圆偏振测量中椭偏参数关于薄膜参数的灵敏度以及入射角对椭偏参数的影响,并进行了具体的仿真分析,得到如下结论：椭偏参数Delta对薄膜光学常数和薄膜厚度变化的灵敏度明显高于椭偏参数Psi。在椭偏数据处理中,椭偏参数Delta的测量精度直接影响薄膜光学常数和薄膜厚度的拟合精度。为了提高椭偏参数Delta的测量精度,可以选择入射角在膺布儒斯特角附近。所得结论对高精度椭偏测量具有指导意义。     

SiO2和HfO2薄膜光学性能的椭偏光谱测量

结合XRD和原子力显微镜等方法,利用椭圆偏振光谱仪测试了单层SiO2薄膜（K9基片）和单层HfO2薄膜（K9基片）的椭偏参数,并用Sellmeier模型和Cauchy模型对两种薄膜进行拟合,获得了SiO2薄膜和HfO2薄膜在300-800nm波段内的色散关系。用X射线衍射仪确定薄膜结构,并用原子力显微镜观察薄膜的微观形貌,分析表明：SiO2薄膜晶相结构呈现无定型结构,HfO2薄膜的晶相结构呈现单斜相结构;薄膜光学常数的大小和薄膜的表面形貌有关;Sellmeier和Cauchy模型较好地描述了该波段内薄膜的光学性能,并得到薄膜的折射率和消光系数等光学常数随波长的变化规律。     

溶胶-凝胶方法制备ZrO2及聚合物掺杂ZrO2单层光学增反射膜

以丙醇锆(Zr(OPr)₄)为原料，乙酸(HAc)为络合剂，聚乙二醇(PEG200)和聚乙烯吡咯烷酮(PVP)为大分子添加剂，在乙醇体系中成功合成了ZrO₂及聚合物掺杂ZrO₂溶胶.用旋涂法在K9玻璃基片上制备单层光学增反射膜.借助小角X射线散射和激光动态光散射技术研究胶体的微结构.采用傅里叶变换红外光谱、差示扫描量热分析、X射线衍射分析、原子力显微镜、紫外/可见/近红外透射光谱以及椭偏仪对薄膜的结构和光学性能进行表征.用输出波长为1064 关键词： 二氧化锆 溶胶-凝胶 增反射膜 激光损伤     

超薄Ag膜的椭偏光谱建模及解谱

用直流溅射法制备了6个不同厚度的超薄Ag膜。结合超薄Ag膜的结构特点,采用了Drude模型联合Lorentz Oscillator模型的解谱方法,得到1～6号样品的厚度分别为4.0,6.2,12.5,26.2,30.0和40.6 nm。从拟合结果的消光系数k图谱中发现,在1号到4号样品中分别于430,450,560和570 nm处出现了表面等离子体共振峰(SPR),随膜厚的增加共振峰宽化且峰位红移。最后,利用SPR理论计算出不同厚度Ag薄膜等离子体共振峰出现的位置,并和实验结果进行了比较。     

Spectroscopic ellipsometric characterization of TiAlN/TiAlON/Si3N4 tandem absorber for solar selective applications

Sputter deposited TiAlN/TiAlON/Si₃N₄ tandem absorber has been characterized by spectroscopic ellipsometry in the wavelength range of 450-1200 nm. Each layer of the tandem absorber viz., TiAlN, TiAlON and Si₃N₄ has been deposited separately on copper substrate (Cu) and ellipsometric measurements have been carried out on each of these layers. The measured ellipsometric spectra were fitted with theoretically simulated spectra and the sample structure and wavelength dispersion of optical constants of each layers have been determined. The ellipsometric measurements have also been carried out on the three-layer tandem absorber deposited on Cu substrate. By analyzing the ellipsometric data, depth profiling of the tandem absorber has been carried out using the derived optical constants of the individual layers.     

椭偏与光度法联用精确测定吸收薄膜的光学常数与厚度

介绍了一种同时利用椭偏仪和分光光度计精确测量薄膜光学常数的方法, 并详细比较了该方法与使用单一椭偏仪拟合结果的可靠性.采用可变入射角光谱型椭偏仪（VASE）表征了250—1700 nm波段辉光放电法沉积的类金刚石薄膜,研究发现当仅用椭偏参数拟合时,由于厚度与折射率、消光系数的强烈相关性,无法得到吸收薄膜光学常数的准确解.如果加入分光光度计测得的透射率同时拟合,得到的结果具有很好的惟一性.该方法无需设定色散模型即可快速拟合出理想的结果,特别适合于确定透明衬底上较薄吸收膜的光学常数. 关键词： 光学常数 光谱型椭偏仪 吸收薄膜 透射率     

Structural, ferroelectric and optical properties of Bi2VO5.5 thin films deposited on platinized silicon {(100) Pt/TiO2/SiO2/Si} substrates

Bismuth vanadate (Bi₂VO_5.5, BVO) thin films have been deposited by a pulsed laser ablation technique on platinized silicon substrates. The surface morphology of the BVO thin films has been studied by atomic force microscopy (AFM). The optical properties of the BVO thin films were investigated using spectroscopic ellipsometric measurements in the 300–820 nm wavelength range. The refractive index (n), extinction coefficient (k) and thickness of the BVO thin films have been obtained by fitting the ellipsometric experimental data in a four-phase model (air/BVO_rough/BVO/Pt). The values of the optical constants n and k that were determined through multilayer analysis at 600 nm were 2.31 and 0.056, respectively. For fitting the ellipsometric data and to interpret the optical constants, the unknown dielectric function of the BVO films was constructed using a Lorentz model. The roughness of the films was modeled in the Brugmann effective medium approximation and the results were compared with the AFM observations. PACS 78.20.-e; 77.84.-s; 77.55.+f     

Optical characterization of thin thermal oxide films on copper by ellipsometry

A complete optical characterization in the visible region of thin copper oxide films has been performed by ellipsometry. Copper oxide films of various thicknesses were grown on thick copper films by low temperature thermal oxidation at 125 °C in air for different time intervals. The thickness and optical constants of the copper oxide films were determined in the visible region by ellipsometric measurements. It was found that a linear time law is valid for the oxide growth in air at 125 °C. The spectral behaviour of the optical constants and the value of the band gap in the oxide films determined by ellipsometry in this study are in agreement with the behaviour of those of Cu₂O, which have been obtained elsewhere through reflectance and transmittance methods. The band gap of copper oxide, determined from the spectral behaviour of the absorption coefficient was about 2 eV, which is the generally accepted value for Cu₂O. It was therefore concluded that the oxide composition of the surface film grown on copper is in the form of Cu₂O (cuprous oxide). It was also shown that the reflectance spectra of the copper oxide–copper structures exhibit behaviour expected from a single layer antireflection coating of Cu₂O on Cu. Received: 19 July 2001 / Accepted: 27 July 2001 / Published online: 17 October 2001     

离子束溅射沉积不同厚度铜膜的光学常数研究

利用Lambda-900分光光度计对离子束溅射沉积不同厚度Cu膜测定的反射率和透射率,运用哈德雷方程,并考虑基片后表面的影响,对离子束溅射沉积的Cu膜光学常数进行了计算。结果表明,在同一波长情况下,膜厚小于100 nm的纳米Cu膜光学常数随膜厚变化明显;膜厚大于100 nm后,Cu膜的光学常数趋于一定值。Cu膜不连续时的光学常数与连续膜时的光学常数随波长变化规律不同;不同厚度的连续膜的光学常数随波长变化规律相同,但大小随膜厚变化而变化。     

Infrared optical properties of Mn1.56Co0.96Ni0.48O4 thin films prepared by chemical solution deposition

～2 μm thick Mn_1.56Co_0.96Ni_0.48O₄ (MCN) films have been prepared on a Al₂O₃ substrate by the chemical solution deposition method. X-ray diffraction and microstructure analyses show good crystallization and the thickness of the films is 2.12 μm. Mid-infrared optical properties of MCN films have been investigated using transmission spectra and infrared spectroscopic ellipsometry. The optical band gap of the MCN film has been derived to be 0.64 eV by assuming a direct transition between valence and conduction bands. The optical constants and thickness of the thin films have been obtained by fitting the measured ellipsometric parameter data with the classical infrared model. The refractive index n of the MCN films decreases as the wavelength increases, but the extinction coefficient k monotonously increases in the wavelength range of 2–7 μm. The maximal n value is 2.63, and the maximal k value is only 0.024. The above results are instructive for the applications of MCN films in infrared detecting.     

Application of spectroscopic ellipsometry to the investigation of the optical properties of cobalt-nanostructured silica thin layers

Spectroscopic ellipsometry is used to investigate optical properties of cobalt-implanted silica thin films. The films under investigation are 250 nm thick thermal SiO₂ layers on Si substrates implanted with Co⁺ ions at energy of 160 keV and at fluences of 10¹⁷ ions/cm² for different temperatures of substrate during implantation (77 and 295 K). Changes due to Co⁺ implantation are clearly observed in the optical response of the films. Optical behaviours are furthermore different for the three implantation temperatures. To understand the optical responses of these layers, the ellipsometric experimental data are compared to different models including interference effects and metal inclusions effects into the dielectric layer. The simulated ellipsometric data are obtained by calculating the interferences of an inhomogeneous layer on a Si substrate. The material within this layer is considered as an effective medium which dielectric function is calculated using the Maxwell-Garnett effective medium approximation. We show that although the structures of these layers are very complicated because of ion-implantation mechanisms, quite simple models can provide relatively good agreement. The possibilities of ellipsometry for the study of the optical properties of such clusters-embedded films are discussed. We especially provide the evidence that ellipsometry can give interesting information about the optical properties of nanostructured layers. This is of special interest in the field of nanostructured layered systems where ellipsometry appears to be a suitable optical characterization technique.     

Infrared spectroscopic ellipsometry of (Pb, La)(Zr, Ti)O3 thin films on platinized silicon

Lead lanthanum zirconate titanate (PLZT) thin films with different La concentrations (x), whose composition is x/40/60, have been grown directly on Pt/Ti/SiO₂/Si (100) substrates by a modified sol-gel method. X-ray diffraction analysis shows that the PLZT thin films are polycrystalline. The infrared optical properties of the PLZT thin films have been investigated using the infrared spectroscopic ellipsometry in the spectral range of 2.5–12.5 μm. By fitting the measured ellipsometric spectra (Ψ and Δ) with a three-phase model (air/PLZT/Pt), and a derived classical dispersion relation for the thin films, the optical constants and thicknesses of the thin films have been obtained. The refractive index of the PLZT thin films decreases with increasing La concentrations, however, the extinction coefficient increases with increasing La concentrations except for the PLZT(4/40/60) thin films. The values of the effective static charge calculated for the PLZT thin films, which state that PLZT belongs to a mixed ionic-covalent compound, decrease with increasing La concentrations. Moreover, the refractive index at the wavelength of 2.5 μm changes linearly with the effective static charge. The plot of the calculated infrared optical absorption versus wavelength for the Ni/PLZT/Pt multilayer structures with various La concentrations is given and indicates that the PLZT thin films are excellent candidates for ferroelectric infrared detectors and focal plane arrays.     

Ellipsometric and reflectance studies of GaAs/AlAs superlattices

Multiple-angle-of-incidence ellipsometry at 632.8 nm and optical reflectance spectra are used to study GaAs/AlAs superlattices on GaAs substrates. The diagnostic potential of the two methods are compared to each other. Precise values of the total film thicknesses are obtained from the ellipsometric data. Significant disagreement between the measured and nominal thicknesses based on RHEED controlled MBE growth conditions is observed. Nonuniformity of a superlattice film is identified with the spatial resolution of about 1 mm². The thickness variations are accompanied by pronounced variations of the optical constants.