ZnCuInS/ZnSe/ZnS量子点发光光谱特性的研究

ZnCuInS/ZnSe/ZnS量子点是一种无毒,无重金属的“绿色”半导体纳米材料。在研究中,制备了三种尺寸的ZnCuInS/ZnSe/ZnS核壳量子点,其直径分别为3.3,2.7,2.3 nm。通过测量不同尺寸的ZnCuInS/ZnSe/ZnS量子点的光致发光光谱,其发射峰值波长随尺寸的减小而蓝移。其吸收峰值波长和发射峰值波长分别是510,611(3.3 nm),483,583(2.7 nm)以及447,545 nm(2.3 nm)。ZnCuInS/ZnSe/ZnS量子点具有显著的尺寸依赖效应。ZnCuInS/ZnSe/ZnS量子点的斯托克斯位移分别为398 meV(3.3 nm),436 meV(2.7 nm)以及498 meV(2.3 nm),这样大的斯托克斯位移证明,ZnCuInS/ZnSe/ZnS量子点的发光机制与缺陷能级有关。同时,对直径为3.3 nm的ZnCuInS/ZnSe/ZnS量子点进行了温度依赖的光致发光光谱的测量,当温度为15～90 ℃时,该量子点发射峰值波长随温度的升高而红移,发光强度随温度的升高而降低,说明ZnCuInS/ZnSe/ZnS量子点是以导带能级与缺陷能级之间跃迁为主的复合发光。     

ZnCuInS/ZnS量子点光致发光温度依赖性研究

ZnCuInS/ZnS量子点是一种无重金属"绿色"半导体纳米材料。制备出了直径为2.9nm的ZnCuInS/ZnS核壳量子点。从ZnCuInS/ZnS量子点的吸收及光致发光光谱中可以看到,量子点的斯托克斯位移为410meV。这样大的斯托克斯位移表明,ZnCuInS/ZnS量子点的复合机制与缺陷能级有关。研究并计算了在辐射及非辐射驰豫过程的(Huang-Rhys)因子及平均声子能量。结果表明在50~373K范围内,能量带隙的变化以及光致发光光谱的增宽是分别由光从能带边缘向缺陷能级跃迁及载流子声子耦合导致的。     

ZnCuInS/ZnS量子点与Poly-TPD补偿发光光谱的研究

ZnCuInS/ZnS量子点是一种无重金属、“绿色”半导体纳米材料。在研究中,制备出尺寸为3.2 nm的ZnCuInS/ZnS核壳量子点,并说明它是施主-受主对复合发光。通过测量ZnCuInS/ZnS量子点的光致发光光谱,其发射峰值波长为620 nm、半宽度是95 nm的红光。同时,还制备出Poly-TPD有机薄膜,其发光光谱是峰值波长为480 nm的蓝光。所以,ZnCuInS/ZnS量子点和Poly-TPD发光颜色具有互补性。在ZnCuInS/ZnS量子点薄膜层上包覆一层poly-TPD薄膜后,二者发光颜色互补。在恰当的偏置电压下,可以得到较好的白光光谱。计算表明,其色坐标是(0.336,0.339),颜色指数是92。     

液相外延GaAs/AlGaAs异质结量子限制效应的光致发光现象

在轻掺杂或不掺杂的GaAs/AlGaAs异质结LPE晶体中,在1.4K的温度下发现了一条新的、由于量子限制效应而出现的PL光谱线—H线。处于GaAs PL光谱的激子跃迁和最浅受主(C)跃迁之问的此H线是一条较宽(半宽～9meV)、拖有一长波方向尾的、而且其峰值能量随激发强度的增加而以对数线性方式移向激子线的高能端(移动超过8meV)的光谱线。H线与温度有密切的关系。随着温度的上升,H线移向较低能的受主跃迁边(达到2meV)而且发光强度很快下降,并在约14K处消失。阶梯蚀刻样品的PL实验证明了H线来源于GaAs/AlGaAs异质结的界面。一个异质结界面的能带不连续模型及其存在的类三角势阱的量子限制效应作用较满意地解释了H线的产生及变化的发光现象,实验表明,H线与此势阱限制的束缚载流子有密切的关系。     

基于InGaN量子点的发光二极管载流子复合动力学研究

InGaN半导体材料具有带隙宽度通过改变In组分可调的特点,被广泛应用在新一代光电子器件中,但绿光LED依然存在"绿隙(green gap)"问题有待解决。本文深入研究载流子复合机制,为解决"绿隙"提供新思路。利用光致荧光光谱(PL)和时间分辨光谱(TRPL)研究了不同温度下对应不同光子能量的InGaN量子点(QDs)发光二极管器件的载流子复合动力学过程,得到了InGaN QDs的瞬态光致发光特性和辐射/非辐射复合的瞬态寿命。稳态光致发光谱在15～300 K的温度范围内,峰值出现先蓝移再红移(S-shaped)的偏移现象,发射峰值蓝移约4.2 meV,在60 K时达到最大值,随后发射峰红移,形成随温度呈S形的变化。这种变化说明QDs结构中载流子局域化行为,激子复合是InGaN量子点绿光发射的主要原因。通过拟合不同温度下的归一化PL积分强度,获得激活能E_(act)约为204.07 meV,激活能较高,证明了InGaN量子点具有较强的载流子限制作用,可以更好抑制载流子向非辐射复合中心迁移,内量子效率(internal quantum efficiency)为35.1%。InGaN QDs中自由载流子复合的平均复合寿命τ_(rad)=73.85ns。能量边界值E_(me)=2.34 eV远高于局域深度E_0=62.55 meV,可见能级完全低于迁移率边缘,因此InGaN QDs寿命衰减归因于载流子局域态复合。通过使用改进的光谱数据分析手段对基于内嵌量子点新结构的荧光器件进行研究,得到了有意义的结论,为进一步了解InGaN量子点内部发光机理和研制新一代照明器件提供借鉴,说明引入InGaN量子点对光电器件的发展具有很好的推动作用。     

气源MBE外延自组装GeSi量子点光致荧光研究

利用气源分子束外延设备（MBE）制作了GeSi自组装量子点样品。利用原子力显微镜（AFM）和光致荧光（PL）光谱研究了量子点的形貌和光学性质。气源MBE在较低温度下生长的量子点材料具有较高的量子点覆盖度。200K以下载流子以局域激子形式束缚在量子点中,激子束缚能约为17meV。升温至200K,载流子的输运过程发生变化。对量子点PL积分强度与温度关系曲线进行拟合得到量子点中空穴跃迁至浸润层的热激活能为129meV。     

壳层相关的CdSe核/壳量子点发光的热稳定性

测量了CdSe/ZnS(3 ML)核/壳结构及CdSe/CdS(3 ML)/ZnCdS(1 ML)/ZnS(2 ML)核/多壳层结构量子点在80~460 K范围内的光致发光光谱,研究了壳层结构对CdSe量子点发光热稳定性的影响。详细地分析了CdSe量子点的发光峰位能量、线宽和积分强度与温度之间的关系,发现CdSe量子点的发光热稳定性依赖于壳层结构。CdS/ZnCdS/ZnS多壳层结构包覆CdSe量子点在低温和高温部分的热激活能均大于ZnS壳层包覆的CdSe量子点,具有更好的发光热稳定性。此外,在300-460-300 K加热-冷却循环实验中,CdS/ZnCdS/ZnS多壳层结构包覆CdSe量子点的发光强度永久性损失更少,热抵御能力更强。     

用于自然原子共振的应力量子调控自组装量子点 单光子源

针对量子存储应用中自组装量子点发射的光子与自然原子系综波长匹配难的问题,通过金-金热压键合技术将含有量子点的纳米薄膜与压电陶瓷进行集成,制作了应力调控的能量可调量子点单光子源,实验上分别实现了对可见光波段镓砷/铝镓砷量子点和近红外波段铟镓砷/镓砷量子点单光子量子比特在9.1meV和4.2meV范围内的宽谱调控.不仅如此,应用应力量子调控技术成功将镓砷/铝镓砷量子点的发光波长调节至铷-87自然原子的D2能级跃迁波长(780nm),以及将铟镓砷/镓砷量子点的发光波长调节至钒酸钇晶体中掺杂的钕离子的4I9/2→4 F3/2跃迁吸收峰共振(879.7nm).该结果为实现基于半导体量子点和自然原子系综的量子存储器提供了一种强有力的调控技术.     

CdSe/ZnSe自组装量子点中非线性系数随着温度的规律性变化(英文)

研究了在CdSe/ZnSe自组装量子点中CdSe量子点的发光随着激发光强度变化的特性。发现当激发强度(I)变化3个数量级的时候,量子点发光的峰位、峰形都没有发生明显的变化。通过公式L∝Ik(其中I是激发光强度,L是量子点发光强度,k是非线性系数)得到非线性系数k值。实验结果表明:在温度由21 K升高到300 K的过程中,k值随温度变化可以分为3个区域:当温度低于120 K时,k值接近于1;然后,随着温度升高,k值慢慢变小;最后,随温度进一步升高,k值由200 K时的0.946迅速减少到0.870。结合发光随温度变化的实验结果,确认在120 K以下发光主要来源于束缚激子复合。在温度由200 K升高到300 K的过程中,非线性系数的单调减小主要归因于随着温度的升高,发光部分来自于由自由电子或空穴到束缚态能级(FB)的复合。进一步通过分析量子点发光的积分强度随着温度的变化的实验结果,发现发光强度随温度升高而减弱的主要原因是材料中的缺陷或者位错等提供非辐射渠道。     

LPCVD自组织生长Si纳米量子点的发光机制分析

采用低压化学气相沉积 (LPCVD)方法 ,通过纯SiH4气体的表面热分解反应 ,在SiO2 表面上自组织生长了半球状Si纳米量子点 ,在室温条件下实验研究了其光致发光 (PL)特性 ,考察了PL效率与峰值能量随Si纳米量子点尺寸的变化关系。结果指出 ,当Si纳米量子点高度hc<5nm时 ,其PL效率基本保持不变。而当hc>5nm时 ,PL效率则急剧下降。同时 ,PL峰值能量随hc 的减少而增大 ,并与 (l/hc) 2 成正比依赖关系。如当hc 从 5 5nm减小至 0 8nm时 ,其峰值能量从 1 2 8eV增加到 1 4 3eV ,出现了约 0 15eV的谱峰蓝移。我们用量子限制效应 界面发光中心复合发光模型解释了这一实验结果     

Photoluminescence Characteristics of ZnCuInS-ZnS Core-Shell Semiconductor Nanocrystals

The photoluminescence(PL) characteristics of ZnCuInS quantum dots(QDs) with varying ZnS shell thicknesses of 0, 0.5, and 1.5 layers are investigated systemically by time-correlated single-photon counting measurements and temperature-dependent PL measurements. The results show that a ZnS shell thickness of 1.5 layers can effectively improve the PL quantum yield in one order of magnitude by depressing the surface trapping states of the core ZnCuInS QDs at room temperature. However, the PL measurements at the elevated temperature reveal that the core-shell nanocrystals remain temperature-sensitive with respect to their relatively thin shells.The temperature sensitivity of these small-sized single-layered core-shell nanocrystals may find applications as effective thermometers for the in vivo detection of biological reactions within cells.     

不同厚度CdSe阱层的表面上自组织CdSe量子点的发光性质

利用变温和变激发功率分别研究了不同厚度CdSe阱层的自组织CdSe量子点的发光。稳态变温光谱表明:低温下CdSe量子阱有很强的发光,高温猝灭,而其表面上的量子点发光可持续到室温,原因归结于量子点的三维量子尺寸限制效应;变激发功率光谱表明:量子点激子发光是典型的自由激子发光,且在功率增加时。宽阱层表面上的CdSe量子点有明显的带填充效应。通过比较不同CdSe阱层厚度的样品的发光,发现其表面上量子点的发光差异较大,这可以归结为阱层厚度不同导致应变弛豫的程度不同,直接决定了所形成量子点的大小与空间分布^[1]。     

Temperature dependence of photoluminescence from self-organized Ge quantum dots with large size and low density

Photoluminescence(PL) from self-organized Ge quantum dots(QDs) with large size and low density has been investigated over a temperature range from 10 to 300 K using continuous-wave(CW) optical excitation.The integrated PL intensity of QDs observed is negligible at about 10 K and rapidly increases with raising temperature up to 100 K.Through analyzing the PL experimental data of the QDs and wetting layer(WL),we provide direct evidence that there exists a potential barrier,arising from the greater compressive...     

Power density and temperature dependent multi-excited states in InAs/GaAs quantum dots

Self-assembled InAs/GaAs (001) quantum dots (QDs) were grown by molecular beam epitaxy using ultra low-growth rate. A typical dot diameter of around 28 ± 2 nm and a typical height of 5 ± 1 nm are observed based on atomic force microscopy image. The photoluminescence (PL) spectra, their power and temperature dependences have been studied for ground (GS) and three excited states (1–3ES) in InAs QDs. By changing the excitation power density, we can significantly influence the distribution of excitons within the QD ensemble. The PL peak energy positions of GS and ES emissions bands depend on an excitation light power. With increasing excitation power, the GS emission energy was red-shifted, while the 1–3ES emission energies were blue-shifted. It is found that the full width at half maximum of the PL spectra has unusual relationship with increasing temperature from 9 to 300 K. The temperature dependence of QD PL spectra shown the existence of two stages of PL thermal quenching and two distinct activation energies corresponding to the temperature ranges I (9–100 K) and II (100–300 K).     

Temperature-dependent photoluminescence of dimethylzinc-treated ZnSe/ZnS quantum dots

Temperature-dependent photoluminescence (PL) measurements were carried out ZnSe/ZnS quantum dots (QDs) grown with post-growth interruption under a dimethylzinc (DMZn) flow. The PL spectra showed sigmoidal peak shifts and V-shaped full width at half maximum (FWHM) variations with increasing temperature, which strongly suggest that the QD structure of ZnSe/ZnS is quite similar to that of other material systems grown in the Stranski–Krastanov mode. Apparent differences are revealed as a consequence of DMZn treatment: (i) the PL spectra of ZnSe/ZnS QDs showed peaks at higher energies and persisted up to 300 K, and(ii) the minimum points of the V-shaped FWHM appear at a higher temperature compared to H₂-purged ZnSe/ZnS QDs. Experimental results demonstrate the enhancement of localization energy.     

Mn掺杂ZnSe量子点变温发光性质研究

量子点(QD)照明器件中电流导致的焦耳热会使其工作温度高于室温,因此研究量子点的发光热稳定性十分重要。本文利用稳态光谱和时间分辨光谱研究了具有不同壳层厚度的Mn掺杂ZnSe(Mn: ZnSe)量子点的变温发光性质,温度范围是80～500 K。实验结果表明,厚壳层(6.5单层(MLs))Mn: ZnSe量子点的发光热稳定性要优于薄壳层(2.6 MLs)的量子点。从80 K升温到400 K的过程中,厚壳层Mn: ZnSe量子点的发光几乎没有发生热猝灭,发光量子效率在400 K高温下依然可以达到60%。通过对比Mn: ZnSe量子点的变温发光强度与荧光寿命,对Mn: ZnSe量子点发光热猝灭机制进行了讨论。最后,为了研究Mn: ZnSe量子点的发光热猝灭是否为本征猝灭,对具有不同壳层厚度的Mn: ZnSe量子点进行了加热-冷却循环(300-500-300 K)测试,发现厚壳层的Mn: ZnSe量子点的发光在循环中基本可逆。因此,Mn: ZnSe量子点可以适用于照明器件,即使器件中会出现不可避免的较强热效应。     

自组织量子点光致荧光的温度依赖性

自组织量子点光致荧光的温度依赖性研究,对于实现室温下高效的量子点光电器件有着非常重要的意义。而量子点中的载流子动力学过程将决定其光致荧光的温度依赖性。采用稳态速率方程模型模拟了自组织量子点中载流子动力学过程,并且考虑了量子点材料带隙随温度的变化;模拟了不同温度下自组织量子点的光致荧光光谱,并获得了光谱的积分强度、峰值能量及半峰全宽随温度的变化曲线。研究表明:模拟结果与已报道的实验数据符合得很好。由此可知,所采用的模型能够很好地反映自组织量子点中的载流子动力学过程。     

Sb/As intermixing in self-assembled GaSb/GaAs type II quantum dot systems and control of their photoluminescence spectra

The intermixing of Sb and As atoms induced by rapid thermal annealing (RTA) was investigated for type II GaSb/GaAs self-assembled quantum dots (QD) formed by molecular beam epitaxy growth. Just as in InAs/GaAs QD systems, the intermixing induces a remarkable blueshift of the photoluminescence (PL) peak of QDs and reduces the inhomogeneous broadening of PL peaks for both QD ensemble and wetting layer (WL) as consequences of the weakening of quantum confinement. Contrary to InAs/GaAs QDs systems, however, the intermixing has led to a pronounced exponential increase in PL intensity for GaSb QDs with annealing temperature up to 875 °C. By analyzing the temperature dependence of PL for QDs annealed at 700, 750 and 800 °C, activation energies of PL quenching from QDs at high temperatures are 176.4, 146 and 73.9 meV. The decrease of QD activation energy with annealing temperatures indicates the reduction of hole localization energy in type II QDs due to the Sb/As intermixing. The activation energy for the WL PL was found to drastically decrease when annealed at 800 °C where the QD PL intensity surpassed WL.     

双模自组织量子点光致发光的温度依赖性

采用稳态速率方程模型,对双模自组织量子点光致发光的温度依赖性进行了研究,模拟获得了不同温度下双模自组织量子点的光致发光光谱,并进一步研究了两组量子点分布的光致发光强度比的温度依赖性。研究表明:在低温下(<75K),两组量子点分布的发光强度比基本保持不变;随着温度的升高(75K相似文献   

Temperature-dependent photoluminescence of CuInS2 quantum dots

Temperature-dependent photoluminescence (PL) spectroscopy of CuInS₂ core and CuInS₂/ZnS core–shell quantum dots (QDs) was studied for understanding the influence of a ZnS shell on the PL mechanism. The PL quantum yield and lifetime of CuInS₂ core QDs were significantly enhanced after the QD surface was coated with the ZnS shell. The temperature dependences of the PL energy, linewidth, and intensity for the core and core–shell QDs were studied in the temperature range from 92 to 287 K. The temperature-dependent shifts of 98 meV and 35 meV for the PL energies of the QDs were much larger than those of the excitons in their bulk semiconductors. It was surprisingly found that the core and core–shell QDs exhibited a similar temperature dependence of the PL intensity. The PL in the CuInS₂/ZnS core–shell QDs was suggested to originate from recombination of many kinds of defect-related emission centers in the interior of the cores.