蓝色荧光粉Sr2B5O9Cl:Eu2+发光特性的研究

采用高温固相法合成了近紫外光激发的蓝色荧光粉Sr₂B₅O₉Cl:Eu²⁺,研究了SrCl₂ ·6H₂O用量和Eu²⁺浓度对其结构和发光性能的影响.随着Eu²⁺浓度的增加,其结构无明显变化,发光强度先增强后减弱,当其浓度为8mol%时,荧光粉的发光强度最大;当用Ca取代Sr时,荧光粉的发射峰从425 nm红移到453 nm. 适当过量 关键词： 氯硼酸盐 蓝色荧光粉 LED     

Preparation and luminescent properties of BaCa2Si3O9:Eu

A blue emitting phosphor of the triclinic BaCa₂Si₃O₉:Eu²⁺ was prepared by the combustion-assisted synthesis method and an efficient blue emission ranging from the ultraviolet to visible was observed. The luminescence and crystallinity were investigated using luminescence spectrometry and X-ray diffractometry (XRD), respectively. The emission spectrum shows a single intensive band centered at 445 nm, which corresponds to the 4f⁶5d¹→4f⁷ transition of Eu²⁺. The excitation spectrum is a broad extending from 260 to 450 nm, which matches the emission of ultraviolet light-emitting diodes (UV-LEDs). The critical quenching concentration of Eu²⁺ in BaCa₂Si₃O₉:Eu²⁺ phosphor is about 0.05 mol. The corresponding concentration quenching mechanism is verified to be a dipole-dipole interaction. The CIE of the optimized sample Ba_0.95Ca₂Si₃O₉:Eu_0.05²⁺ was (x, y)=(0.164, 0.111). The result indicates that BaCa₂Si₃O₉:Eu²⁺ can be potentially useful as a UV radiation-converting phosphor for white light-emitting diodes (LEDs).     

Synthesis and crystal structures and luminescent properties of divalent europium-doped Ba2ZnSi2O7 and BaZn2Si2O7

The monoclinic Ba₂ZnSi₂O₇:Eu²⁺ blue-green-emitting phosphor and the orthorhombic BaZn₂Si₂O₇:Eu²⁺ green-emitting phosphor were prepared by combustion-assisted synthesis method as the fluorescent materials for ultraviolet-light-emitting diodes (UV-LEDs) performed as a light source. The crystallinity and luminescence were investigated using X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy. Pure monoclinic Ba₂ZnSi₂O₇ and orthorhombic BaZn₂Si₂O₇ crystallize completely at 1100 °C. The doped Eu²⁺ ions did not cause any significant change in the host structure. The emission spectra presented an emission position red shift of up to 16 nm from Ba₂ZnSi₂O₇:Eu²⁺ to BaZn₂Si₂O₇:Eu²⁺. The excitation spectra of Ba₂ZnSi₂O₇:Eu²⁺ and BaZn₂Si₂O₇:Eu²⁺ were broad-banding, extending from 260 to 465 nm, which match the emission of UV-LEDs.     

Effect of Sr2+-doping on structure and luminescence properties of BaAl2Si2O8:Eu2+ phosphors

Sr²⁺ doped BaAl₂Si₂O₈:Eu²⁺ phosphor was synthesized by chemical co-precipitation method. With the increase of Sr²⁺ concentration, the phase structure of (Ba_0.965 ? xSr_xEu_0.035)Al₂Si₂O₈ changes from hexagonal phase to monoclinic phase owing to large activation energy in SrAl₂Si₂O₈ system. (Ba_0.965 ? xSr_xEu_0.035)Al₂Si₂O₈ phosphor exhibits a broad blue band peaking at 425 nm due to the 4f⁶5d–4f⁷(⁸S_7/2) transition of Eu²⁺ ions. The emission intensity increases, accompanied by the blue shift of emission maximum from 459 to 417 nm with the Sr²⁺ doping concentration increasing. The optimal concentration of Sr²⁺ ion is 40%, and the phosphor shows high color stability in CIE chromaticity diagram. The result indicates that Sr²⁺ doped phosphor not only can enhance the relative intensity but also can adjust the chromaticity coordinate.     

H3BO3对BaAl2Si2O8：Eu2+蓝色荧光粉物相组成和发光特性的影响

采用化学共沉淀法一次煅烧工艺合成了BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉.用X射线衍射仪、荧光分光光度计和扫描电镜测试了助熔剂H₃BO₃对BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉物相结构、发光性能、形貌等的影响.研究表明：化学共沉淀法一次煅烧工艺合成的BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉为单相,H₃BO₃的加入使基质结构由六方相转变成单斜相,并引起发射主峰位置和发射强度的变化;BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉的发光强度随着H₃BO₃加入量的增加先增强,后减弱,当加入H₃BO₃的质量分数为1.5%时,发光强度最大;H₃BO₃的加入使合成BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉的颗粒呈类球形,分布更加均匀,粒度更小. 关键词： 3BO₃')" href="#">H₃BO₃ 2Si₂O₈：Eu²⁺')" href="#">BaAl₂Si₂O₈：Eu²⁺ 发光特性 化学共沉淀法     

Green Eu-doped Ba3Si6O12N2 phosphor for white light-emitting diodes: Synthesis, characterization and theoretical simulation

The Eu²⁺-doped Ba₃Si₆O₁₂N₂ green phosphor (Eu_xBa_3−xSi₆O₁₂N₂) was synthesized by a conventional solid state reaction method. It could be efficiently excited by UV-blue light (250-470 nm) and shows a single intense broadband emission (480-580 nm). The phosphor has a concentration quenching effect at x=0.20 and a systematic red-shift in emission wavelength with increasing Eu²⁺ concentration. High quantum efficiency and suitable excitation range make it match well with the emission of near-UV LEDs or blue LEDs. First-principles calculations indicate that Ba₃Si₆O₁₂N₂:Eu²⁺ phosphor exhibits a direct band gap, and low band energy dispersion, leading to a high luminescence intensity. The origin of the experimental absorption peaks is clearly identified based on the analysis of the density of states (DOS) and absorption spectra. The photoluminescence properties are related to the transition between 4f levels of Eu and 5d levels of both Eu and Ba atoms. The 5d energy level of Ba plays an important role in the photoluminescence of Ba₃Si₆O₁₂N₂:Eu²⁺ phosphor. The high quantum efficiency and long-wavelength excitation are mainly attributed to the existence of Ba atoms. Our results give a new explanation of photoluminescence properties and could direct future designation of novel phosphors for white light LED.     

Synthesis,characterization and studies of radiative properties on Eu3+-doped ZnAl2O4

Eu³⁺-doped ZnAl₂O₄ phosphors were successfully synthesized in air atmosphere at 900 °C. The phosphors were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), thermally stimulated luminescence (TSL) and photoluminescence (PL) techniques. The average particle size of the system as determined from SEM was found to be 100–150 nm (for samples annealed at 900 °C). PL spectra of the doped phosphors showed emission peaks corresponding to Eu³⁺ ions. Lifetime studies revealed Eu³⁺ ions to be in two different sites. The asymmetric ratio (I₆₁₆/I₅₉₂) was observed to be about 3.75. This suggested that Eu³⁺ ion entered the host mainly substituting Al³⁺ site distorting the local environment and is partly located on surface of the phosphors. A prominent glow peak at 430 K was observed in the TSL of γ-irradiated Eu³⁺-doped ZnAl₂O₄ phosphors. Trap parameters for this peak have been determined and the probable mechanism for the glow peak is proposed. CIE chromaticity coordinates for the system were evaluated. It was observed that, the system could be employed as a potential red emitting phosphor. Commercial utility of the phosphor was investigated by comparing it with commercial red phosphor. The PL intensity of the as prepared phosphors was 63% of that of the commercial phosphor. Apart from this, various radiative properties such as the Judd–Ofelt intensity parameters, spontaneous emission probabilities, luminescence branching ratios, radiative lifetimes and quantum efficiency were evaluated for the system.     

Photoluminescence properties of blue-emitting Li4SrCa(SiO4)2:Eu2+ phosphor for solid-state lighting

Blue-emitting Li₄SrCa(SiO₄)₂:Eu²⁺ phosphors have been synthesized by solid-state reaction. The photoluminescence (PL) excitation spectrum shows broad-band absorption and matches well with the emission of a near-UV (n-UV) chip. The PL emission spectrum exhibits a broad-band emission peaking at 430 nm, which is the characteristic emission of the f–d transition of the Eu²⁺ ion. The diffuse reflection spectra, temperature-dependent emission spectra, fluorescence decay, and mechanism of concentration quenching are also studied in detail. Li₄SrCa(SiO₄)₂:Eu²⁺ is a candidate blue phosphor for n-UV excited solid-state lighting.     

Photoluminescence of sol–gel-derived Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> thin-film phosphors with Mg<Superscript>2+</Superscript> and Al<Superscript>3+</Superscript> co-doping

Red-light-emitting Y₂O₃:Eu³⁺ thin-film phosphors were synthesized using a sol–gel process. The effect of Mg²⁺ and Al³⁺ co-dopants on the Y₂O₃:Eu³⁺ thin-film phosphor photoluminescence (PL) property was investigated. At a certain concentration, both Mg²⁺ and Al³⁺ co-dopants were found to further enhance the PL emission intensity of Y₂O₃:Eu³⁺ thin-film phosphors. The optimum PL emission intensity was observed in Y₂O₃:12%Eu³⁺, 7%Mg²⁺ and Y₂O₃:12%Eu³⁺, 2%Al³⁺ phosphor films. From our results, the enhancement of the emission intensity by the Mg²⁺ and Al³⁺ co-dopants is explained in terms of the creation of defect states near the Y(4d+5s) conduction band, which overlap with the Eu³⁺ charge-transfer state (CTS). The overlapping leads to CTS broadening and consequently induces higher absorption and hence an increase of the emission intensity. From X-ray diffraction results, we have found that there is no additional phase formed in the co-doped phosphor films. PACS 68.55.Ln; 78.55.-m; 81.20.Fw     

Orange emission enhancement by energy transfer in Sr3Al2O5Cl2:Ce, Eu phosphor for solid-state lighting

Orange-emissive Ce³⁺/Eu²⁺ co-doped Sr₃Al₂O₅Cl₂ phosphors were synthesized by a solid-state reaction. The large overlap between the emission spectrum of blue Sr₃Al₂O₅Cl₂:Ce³⁺ and the excitation spectrum of orange Sr₃Al₂O₅Cl₂:Eu²⁺, and the shortening trend in lifetime of Ce³⁺ donors with increasing Eu²⁺ concentration in Sr₃Al₂O₅Cl₂:Ce³⁺, Eu²⁺ provide the strong evidence of energy transfer from Ce³⁺ to Eu²⁺ ions. It supports that the orange emission intensity of the optimal co-doped phosphor is 1.5 times stronger than that of single Eu²⁺-doped one. The Sr₃Al₂O₅Cl₂:Ce³⁺, Eu²⁺ phosphor is a promising orange-emitting phosphor for warm-white-light-emitting diode because of its effective excitation in the near ultraviolet range.     

Eu$lt;sup$gt;2+$lt;/sup$gt;的掺杂浓度对BaAl$lt;sub$gt;2$lt;/sub$gt;Si$lt;sub$gt;2$lt;/sub$gt;O$lt;sub$gt;8$lt;/sub$gt;：Eu$lt;sup$gt;2+$lt;/sup$gt;荧光粉发光特性的影响

采用化学共沉淀法一次煅烧工艺合成了BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉.用X射线衍射仪和荧光分光光度计等对BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉的相结构、发光性能进行了测试.结果表明：化学共沉淀法一次煅烧工艺合成的BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉为单相;其激发光谱分布在240—410 nm的波长范围,峰值位于320 nm处,可以被InGaN管芯产生的350—410 nm辐射有效激发;在365 nm近紫外光的激发下,测得其发射光谱是位于465 nm附近的宽带峰.BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉的发光强度随Eu²⁺浓度的增大逐渐加强,当Eu²⁺掺杂的摩尔分数为3.5%时,发光强度达到最大值,而后随掺杂浓度的增加而减小,发生浓度猝灭;根据Dexter能量共振理论,该浓度猝灭是由于Eu²⁺的离子间交换相互作用引起的. 关键词： 2Si₂O₈：Eu²⁺')" href="#">BaAl₂Si₂O₈：Eu²⁺ 发光特性 蓝色荧光粉 化学共沉淀法     

Photoluminescence and afterglow behavior of Eu, Dy and Eu, Dy in Sr3Al2O6 matrix

This paper reports the photoluminescence and afterglow behavior of Eu²⁺ and Eu³⁺ in Sr₃Al₂O₆ matrix co-doped with Dy³⁺. The samples containing Eu²⁺ and Eu³⁺ were prepared via solid-state reaction. X-ray diffraction (XRD), photo luminescent spectroscope (PLS) and thermal luminescent spectroscope (TLS) were employed to characterize the phosphors. The comparison between the emission spectra revealed that Sr₃Al₂O₆ phosphors doped with Eu²⁺, Dy³⁺ and Eu³⁺, Dy³⁺ showed different photoluminescence. The phosphor doped with Eu³⁺, Dy³⁺ showed an intrinsic f-f transition generated from Eu³⁺, with two significant emissions at 591 and 610 nm. However, the phosphor doped with Eu²⁺, Dy³⁺ revealed a broad d-f emission centering around 512 nm. After the UV source was turned off, Eu²⁺, Dy³⁺ activated Sr₃Al₂O₆ phosphor showed excellent afterglow while Eu³⁺, Dy³⁺ activated phosphor almost showed no afterglow. Thermal simulated luminescence study indicated that the persistent afterglow of Sr₃Al₂O₆: Eu²⁺, Dy³⁺ phosphor was generated by suitable electron traps formed by the co-doped rare-earth ions (Dy³⁺) within the host.     

Synthesis and luminescence properties of Na2Ba2Si2O7:Eu2+ phosphor

Green-emitting phosphor Na₂Ba₂Si₂O₇:Eu²⁺ has been synthesized by a conventional high-temperature solid-state reaction. The phase structure and luminescence properties are characterized by the X-ray powder diffraction, diffuse reflectance spectra, photoluminescence excitation and emission spectra, temperature-dependent emission spectra, respectively. It can be efficiently excited in the wavelength range of 325–400 nm and consists of a strong broad green band centered at about 501 nm, which is ascribed to 4f⁶6s⁰5d¹ → 4f⁷6s²5d⁰ transition of Eu²⁺. The critical quenching concentration of Eu²⁺ in the Na₂Ba₂Si₂O₇ host is about 0.8 mol % and corresponding quenching behavior is ascribed to be electric dipole–dipole interaction. Furthermore, the phosphor has good thermal stability property, and the activation energy for thermal quenching is calculated as 0.34 eV.     

Luminescent properties of Eu2+and Dy3+ ions in Ba4Al2O7 phosphor for solid state lighting

In this paper we report the combustion synthesis of rare earth (RE=Eu, Dy) doped Ba₄Al₂O₇ phosphors. Prepared phosphors were characterized by X-ray powder diffraction (XRD), scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), CIE color co-ordinates and their photoluminescence (PL) properties were also investigated. In case of Ba₄Al₂O₇: Eu²⁺, the emission spectra show unique band centered at 495 nm, which corresponds to the 4f⁶5d¹→4f⁷ transition of Eu²⁺, and PL emission spectra of Dy³⁺ ion under 348 nm excitation give two bands centered at 478 nm (blue) and 575 nm (yellow), which originate from the transitions of ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 of Dy³⁺, respectively. The results indicate that the Eu²⁺ and Dy³⁺ activated Ba₄Al₂O₇ phosphor could find application in solid state lighting.     

Morphology-dependent luminescence behavior of Y<Subscript>2-x</Subscript>Gd<Subscript>x</Subscript>O<Subscript>3</Subscript>:Eu<Superscript>3+</Superscript> thin-film phosphors grown by a laser ablation

Y_2-xGd_xO₃:Eu³⁺ luminescent thin films have been grown on Al₂O₃(0001) substrates using pulsed laser deposition. Films grown under different deposition conditions have been characterized using microstructural and luminescence measurements. The crystallinity, surface morphology and photoluminescence (PL) of the films are highly dependent on the amount of Gd present. The photoluminescence (PL) brightness data obtained from Y_2-xGd_xO₃:Eu³⁺ films grown under optimized conditions have indicated that Al₂O₃(0001) is one of the most promising substrates for the growth of high-quality Y_2-xGd_xO₃:Eu³⁺ thin-film red phosphors. In particular, the incorporation of Gd into the Y₂O₃ lattice could induce a remarkable increase of PL. The highest emission intensity was observed with Y_1.35Gd_0.60Eu_0.05O₃, whose brightness was increased by a factor of 3.1 in comparison with that of Y₂O₃:Eu³⁺ films. This phosphor may be promising for application in flat-panel displays. PACS 78.20.-e; 78.55.-m; 78.66.-w     

Enhanced blue emission and EPR study of LaMgAl11O19:Eu phosphors

Europium doped LaMgAl₁₁O₁₉ phosphor was prepared by the combustion method. The as-prepared and post-treated (1350 °C 10 h 5% H₂+95% N₂) phosphors were investigated by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), photoluminescence (PL) and electron paramagnetic resonance (EPR) techniques. XRD patterns show that LaMgAl₁₁O₁₉:Eu phosphors have hexagonal structure. FT-IR spectrum exhibits absorption bands corresponding to the stretching vibration of AlO₄ and AlO₆. Morphological studies reveal that this phosphor has faceted plates of varying sizes and shapes. The as-prepared LaMgAl₁₁O₁₉:Eu phosphor consists of both Eu³⁺ and Eu²⁺ ions. The phosphor exhibits a bright blue emission at 450 nm (4f⁶5d→4f⁷ transition of Eu²⁺). On post-treating the phosphor we are able to enhance the blue emission efficiency by 330%. The process was detected from the evolution of excitation, emission and EPR spectra and the results are discussed.     

Photoluminescence properties of Sr1-xSi2O2N2: Eux as green to yellow-emitting phosphor for blue pumped white LEDs

This study evaluated potential applications of green to yellow-emitting phosphors (Sr_1−xSi₂O₂N₂: Eu²⁺_x) in blue pumped white light emitting diodes. Sr_1-xSi₂O₂N₂: Eu²⁺_x was synthesized at different Eu²⁺ doping concentrations at 1450 °C for 5 h under a reducing nitrogen atmosphere containing 5% H₂ using a conventional solid reaction method. The X-ray diffraction patterns of the prepared phosphor (Sr_1-xSi₂O₂N₂: Eu²⁺_x) were indexed to the SrSi₂O₂N₂ phase and an unknown intermediate phase. The photoluminescence properties of these phosphors (Sr_1−xSi₂O₂N₂: Eu²⁺_x) showed that the samples were excited from the UV to visible region due to the strong crystal field splitting of the Eu²⁺ ion. The emission spectra under excitation of 450 nm showed a bright color at 545-561 nm. The emission intensity increased gradually with increasing Eu²⁺ doping concentration ratio from 0.05 to 0.15. However, the emission intensity decreased suddenly when the Eu²⁺ concentration ratio was >0.2. As the doping concentration of Eu²⁺ was increased, there was a red shift in the continuous emission peak. These results suggest that Sr_1-xSi₂O₂N₂: Eu₂⁺_x phosphor can be used in blue-pumped white light emitting diodes.     

Photoluminescence properties of Eu and Mn-activated BaMgP2O7 as a potential red phosphor for white-emission

A phosphate compound, BaMgP₂O₇ was co-doped with Eu²⁺ and Mn²⁺ for making a red-emitting phosphor. The phosphor was prepared by a solid-state reaction at high temperature. The photoluminescence properties were investigated under ultraviolet (UV) ray excitation. From a powder X-ray diffraction (XRD) analysis, the formation of single-phased BaMgP₂O₇ with a monoclinic structure was confirmed. In the photoluminescence spectra, the BaMgP₂O₇:Eu,Mn phosphor emits two distinctive colors: a blue band centered at 409 nm originating from Eu²⁺ and a red band at 615 nm caused by Mn²⁺. Also, efficient energy transfer from Eu²⁺ to Mn²⁺ in the BaMgP₂O₇:Eu,Mn system was verified by observing that the excitation spectra of BaMgP₂O₇:Eu,Mn emitted at 409 and 615 nm by Eu²⁺ emission and Mn²⁺ emission, respectively, are almost the same as that of BaMgP₂O₇:Eu monitored at 409 nm. The optimum concentration of Eu²⁺ ions in BaMgP₂O₇:0.015Eu excited at 309 nm wavelength is 1.5 mol%. With an increase of Mn²⁺ content up to 17.5 mol%, a systematic decline in the intensity of the excitation spectrum by Eu²⁺ and a gradual growth in the intensity of emission band by Mn²⁺ were observed. Accordingly, the optimum concentration of Mn²⁺ in BaMgP₂O₇:0.015Eu,Mn is 17.5 mol%. The maximum spectral overlap between emission of Eu²⁺ and excitation of Mn²⁺ is achieved in a composition of BaMgP₂O₇:0.015Eu,0.175Mn, resulting in considerable red-emission at 615 nm.     

Structure and luminescence of Ca2Si5N8：Eu^2＋ phosphor for warm white light-emitting diodes

We have synthesized Ca 2 Si 5 N 8:Eu 2+ phosphor through a solid-state reaction and investigated its structural and luminescent properties.Our Rietveld refinement of the crystal structure of Ca 1.9 Eu 0.1 Si 5 N 8 reveals that Eu atoms substituting for Ca atoms occupy two crystallographic positions.Between 10 K and 300 K,Ca 2 Si 5 N 8:Eu 2+ phosphor shows a broad red emission band centred at ～1.97 eV-2.01 eV.The gravity centre of the excitation band is located at 3.0 eV-3.31 eV.The centroid shift of the 5d levels of Eu 2+ is determined to be ～1.17 eV,and the red-shift of the lowest absorption band to be ～ 0.54 eV due to the crystal field splitting.We have analysed the temperature dependence of PL by using a configuration coordinate model.The Huang-Rhys parameter S=6.0,the phonon energy ν=52 meV,and the Stokes shift S=0.57 eV are obtained.The emission intensity maximum occurring at ～200 K can be explained by a trapping effect.Both photoluminescence (PL) emission intensity and decay time decrease with temperature increasing beyond 200 K due to the non-radiative process.     

Orange emissive Sr3Al2O5Cl2:Eu2+ phosphor for warm-white light-emitting diodes

Orange-emitting Sr₃Al₂O₅Cl₂:Eu²⁺ phosphors were synthesized by a high-temperature solid-state reaction. The excitation spectrum shows a broad band from the UV region to the blue region. The emission spectrum shows strong orange emission peaking at 610 nm, attributed to the d–f transition of the Eu²⁺ ion. By combining the Sr₃Al₂O₅Cl₂:Eu²⁺ phosphor with 420 nm and 460 nm chips, three white light-emitting diodes (LEDs) were fabricated. The warm-white LEDs show color rendering indexes of 76, 66 and 90 with color temperatures of 2447, 3546 and 4300 K, respectively. This new phosphor exhibits the potential to act as a single host doped with Eu²⁺ phosphor for UV or blue chip excited white LEDs.