Effects of laser power density on the microstructure and microhardness of Ni–Al alloyed layer by pulsed laser irradiation

Laser alloying of Ni–P electroless deposited layer with aluminum substrate was carried out by Nd–YAG pulsed laser. The phase composition and microstructure of the alloyed layers produced by different laser power densities were identified by X-ray diffractionary (XRD), scanning electron microscope (SEM) accompanied by energy dispersion X-ray analysis (EDS) and transmission electron microscope (TEM). Furthermore, the surface roughness of the alloyed layers was characterised by confocal laser scanning microscope (CLSM). The results showed that the characteristic dendritic or lamellar microstructures were observed in the alloyed layers. The phase constituents of the alloyed zones were intermetallic compounds of nickel–aluminum NiAl, Al₃Ni and Al₃Ni₂, as well as some non-equilibrium phases and amorphous phases depending on the employed laser power density. As a result, the microhardness of the alloyed layer with Ni–P amorphous phases formed at laser power density 5.36×10⁹ W/m² reached to HV_0.1 390.     

Effect of cellulose–lignin interactions on char structural changes during fast pyrolysis at 100–350 °C

This study investigates the cellulose–lignin interactions during fast pyrolysis at 100–350 °C for better understanding fundamental pyrolysis mechanism of lignocellulosic biomass. The results show that co-pyrolysis of cellulose and lignin (with a mass ratio of 1:1) at temperatures < 300 °C leads to a char yield lower than the calculated char yield based on the addition of individual cellulose and lignin pyrolysis. The difference between the experimental and calculated char yields increases with temperature, from ～2% 150 °C to ～6% at 250 °C. Such differences in char yields provide direct evidences on the existence of cellulose–lignin interactions during co-pyrolysis of cellulose and lignin. At temperatures below 300 °C, the reductions in both lignin functional groups and sugar structures within the char indicate that co-pyrolysis of cellulose and lignin enhances the release of volatiles from both cellulose and lignin. Such an observation could be attributed to two possible reasons: (1) the stabilization of lignin-derived reactive species by cellulose-derived reaction intermediates as hydrogen donors, and (2) the thermal ejection of cellulose-derived species due to micro-explosion of liquid intermediates from lignin. In contrast, at temperatures ≥ 300 °C, co-pyrolysis of cellulose and lignin increases char yields, i.e., with the difference between the experimental and calculated char yields increasing from ～1% at 300 °C to ～8% at 350 °C. The results indicate that the cellulose-derived volatiles are difficult to diffuse through the lignin-derived liquid intermediates into the vapor phase, leading to increased char formation from co-pyrolysis of cellulose and lignin as temperature increases. Such an observation is further supported by the increased retention of cellulose functional groups in the char from co-pyrolysis of cellulose and lignin.     

Fabrication and characterization of cellulose nanoparticles from maize stalk pith via ultrasonic-mediated cationic etherification

In this study, parenchyma cellulose, which was extracted from maize stalk pith as an abundant source of agricultural residues, was applied for preparing cellulose nanoparticles (CNPs) via an ultrasound-assisted etherification and a subsequent sonication process. The ultrasonic-assisted treatment greatly improved the modification of the pith cellulose with glycidyltrimethylammonium chloride, leading to a partial increase in the dissolubility of the as-obtained product and thus disintegration of sheet-like cellulose into nanoparticles. While the formation of CNPs by ultrasonication was largely dependent on the cellulose consistency in the cationic-modified system. Under the condition of 25% cellulose consistency, the longer sono-treated duration yielded a more stable and dispersible suspension of CNP due to its higher zeta potential. Degree of substitution and FT-IR analyses indicated that quaternary ammonium salts were grafted onto hydroxyl groups of cellulose chain. SEM and TEM images exhibited the CNP to have spherical morphology with an average dimeter from 15 to 55 nm. XRD investigation revealed that CNPs consisted mainly of a crystalline cellulose Ι structure, and they had a lower crystallinity than the starting cellulose. Moreover, thermogravimetric results illustrated the thermal resistance of the CNPs was lower than the pith cellulose. The optimal CNP with highly cationic charges, good stability and acceptable thermostability might be considered as one of the alternatively renewable reinforcement additives for nanocomposite production.     

Catalytic production of carbon nanotubes by vapor phase growth method using tungsten-containing organic compound

We report the production of carbon nanotubes of high purity by a vapor phase growth method using a catalytic reaction of a tungsten-containing organic compound (C₁₄H₁₀O₇W) and acetylene mixture. The products were multi-walled carbon nanotubes with hollow cores. Transmission electron microscopy investigation revealed that the graphitic layers at the inner region were highly crystallized but the graphitic layers at the outer region had a wavy structure. We have demonstrated the effective production of carbon nanotubes using a tungsten-based catalyst. PACS 81.07.De; 61.46.+w; 68.37.-d     

Structural transformation of graphite by arc-discharge

The formation of novel structures by the passage of an electric current through graphite is described. These structures apparently consist of hollow three-dimensional graphitic shells bounded by curved and faceted planes, typically made up of two graphene layers. The curved structures were frequently decorated with nano-scale carbon particles, or short nanotubes. In some cases, nanotubes were found to be seamlessly connected to the thin shells, indicating that the formation of the shells and the nanotubes is intimately connected. Small nanotubes or nanoparticles were also sometimes found encapsulated inside the hollow structures, while fullerene-like particles were often seen attached to the outside surfaces. With their high surface areas and structural perfection, the new carbon structures may have applications as anodes of lithium ion batteries or as components of composite materials.     

Electron Acceleration by Beating of Two Intense Cross-Focused Hollow Gaussian Laser Beams in Plasma

This paper presents propagation of two cross-focused intense hollow Gaussian laser beams(HGBs) in collisionless plasma and its effect on the generation of electron plasma wave(EPW) and electron acceleration process,when relativistic and ponderomotive nonlinearities are simultaneously operative. Nonlinear differential equations have been set up for beamwidth of laser beams, power of generated EPW, and energy gain by electrons using WKB and paraxial approximations. Numerical simulations have been carried out to investigate the effect of typical laser-plasma parameters on the focusing of laser beams in plasmas and further its effect on power of excited EPW and acceleration of electrons. It is observed that focusing of two laser beams in plasma increases for higher order of hollow Gaussian beams,which significantly enhanced the power of generated EPW and energy gain. The amplitude of EPW and energy gain by electrons is found to enhance with an increase in the intensity of laser beams and plasma density. This study will be useful to plasma beat wave accelerator and in other applications requiring multiple laser beams.     

Phototransformations of substituted <Emphasis Type="Italic">p</Emphasis>-terphenyl upon excitation by a XeCl laser

Phototransformations of 1,8-dicarboxyisobutyl-substituted p-terphenyl in ethanol are studied upon excitation by a XeCl laser at a power density of up to 180 MW/cm² for different types of radiation and different excitation geometries. The absorption and emission spectra are studied before and after irradiation. The resources of the lasing medium, quantum yields of phototransformations, and relative quantum yields of photoproducts are determined. The transmission of the solutions at the excitation wavelength and the shape of radiation pulses are measured as functions of the pump power density.     

Multiwavelength laser light transmission of hollow optical fiber from the visible to the mid-infrared

We report on low-loss multiwavelength laser delivery of hollow optical fiber in a wide wavelength region, from the visible to the infrared. Improved methods of liquid-phase coating were used to fabricate the hollow fiber with inner films of a silver and a cyclic olefin polymer (COP) layer. The surface roughness of the silver layer was reduced dramatically by pretreatment on the inner glass surface with an SnCl2 solution. The COP layer roughness was also decreased by using an ambient atmosphere of tetrahydrofuran (THF) solvent during the COP layer formation. Owing to the smooth surfaces, hollow fiber with optimum COP film thickness for CO2 laser light simultaneously yields low losses for a Er:YAG laser and a red pilot beam. The power durability of CO2 and Er:YAG lasers, as well as the loss properties for the pilot beam, is demonstrated.     

NOx and N2O precursors (NH3 and HCN) from biomass pyrolysis: Co-pyrolysis of amino acids and cellulose, hemicellulose and lignin

Nitrogen in biomass is mainly in forms of proteins (amino acids). Glycine, glutamic acid, aspartic acid, leucine, phenylalanine and proline are the major amino acids in agricultural straw. The six amino acids were pyrolyzed individually at 800 °C in a tubular reactor in an argon atmosphere. Each amino acid sample was then pyrolyzed individually with cellulose, hemicellulose or lignin with 1:1 mixing ratio by weight under the same condition. The emissions of HCN and NH₃ were detected with a Fourier transform infrared (FTIR) spectrometer. The extent of interaction between the amino acids with cellulose, hemicellulose or lignin was determined by comparing the yields of HCN and NH₃ from co-pyrolysis with those from single amino acid pyrolysis under the same condition. The results indicate that the structure of the amino acid has a significant effect on the nitrogen transformation during pyrolysis. The mixtures undergo solid-state decomposition reactions during co-pyrolysis. The extent of interaction between the amino acids with cellulose, hemicellulose or lignin depends on the amino acid types and the components in biomass. Although single proline and leucine form no char, they give a significant amount of nitrogen-containing char when co-pyrolyzed with cellulose, hemicellulose and lignin. HCN and NH₃ yields and nitrogen conversion pathway from amino acid pyrolysis are influenced by cellulose, hemicellulose and lignin.     

Power factor of very thin thermoelectric layers of different thickness prepared by laser ablation

Room temperature conductivity and the Seebeck coefficient of thin layers prepared by laser ablation from Bi₂Te₃ target were explored. The power factor was calculated for samples prepared at substrate temperature of 360°C with the density of the laser beam 5 J cm⁻² and at substrate temperature of 410°C with the density of the laser beam 2 J cm⁻² during the deposition. Oscillations of the conductivity and the power factor with the layer thickness were observed at room temperature. The oscillations of conductivity were also verified at the temperature of 77 K. The period of oscillations depends on the preparation conditions. This behavior has been theoretically explained by the quantum size effect in the layers containing different phases and in addition, it was demonstrated by the X-ray Diffraction measurement. The behavior of the power factor of the layers is compared to the behavior of the figure of merit of the layers published earlier.     

Effect of silicon on the formation of graphitic polyhedra and balloon-like particles

We conducted laser vaporization of graphite and graphite containing 1 at. % silicon in Ar gas atmosphere. Comparison of the products from the laser vaporization indicated that the coexistence of Si promoted graphitization in grown carbon particles of 90–1500 nm. Polyhedral graphite (PG) particles and balloon-like carbon (BC) particles with shells of graphitic layers were grown under control of Ar gas pressures of 0.1–0.7 MPa. We discuss possible roles of Si in graphitic structure growth and the formation mechanisms of the PG and BC particles. PACS 81.16.Mk; 61.46.Df; 68.37.Lp     

大面阵激光二极管阵列端面泵浦耦合技术

为了满足常温Yb:YAG激光放大器对泵浦功率密度的要求,设计了一种高缩束比的耦合系统。根据激光二极管（LD）的发光特性,将输出功率为80 kW的LD阵列进行拟球面排列,采用正交柱面透镜配合空心导光管进行泵浦耦合,耦合系统的面积缩束比高达86∶1。模拟计算表明,该耦合系统的耦合效率对导光管反射板的反射率依赖性较低,且脱离耦合系统后的泵浦光传输8.5 mm后,依然可以保持泵浦光场的轮廓,满足端面泵浦的常温Yb:YAG片状放大器对泵浦耦合系统的要求。     

Growth of single-wall carbon nanotubes dependent on laser power density and ambient gas pressure during room-temperature CO2 laser vaporization

Single-wall carbon nanotubes (SWNTs) were synthesized by the irradiation of 20-ms CO₂ laser pulses onto a graphite–Co/Ni target at room temperature. We investigated the effect of laser power density (10–150 kW/cm²) and ambient Ar gas pressure (150–760 Torr) on the abundance of SWNTs with lengths of up to about 200 nm in soot-like carbonaceous deposits. For a constant power density (30 kW/cm²), depending on the Ar gas pressure, SWNTs with diameters of 1.2–1.4 nm were synthesized. Expansion behavior and temperature-fall rates of clusters and/or particles in laser plumes were also analyzed by high-speed video imaging and temporally and spatially resolved emission spectroscopy. The temperature-fall rates were estimated to be 171–427 K/ms. The SWNT growth on the time scale of a few milliseconds appeared to be related to some features of condensing clusters and/or particles, including resident densities, collision frequencies and temperatures. Received: 16 July 2001 / Accepted: 23 July 2001 / Published online: 30 August 2001     

Numerical modeling of a He-Kr coil hollow cathode laser

A theoretical study of a He-Kr laser (KrII, 469.4 nm line) pumped by a helical hollow cathode discharge is presented. A detailed kinetic model of plasmachemical reactions and radiative processes including the influence of gas heating on the active medium is developed. In the process of numerical calculations the dependence of the plasma parameters (electron and gas temperature, electron and metastable density, upper and lower laser level density) and laser characteristics (output power and gain coefficient) on the variations of discharge pumping, gas-mixture partial pressures and geometry of the coil hollow cathode, are investigated. The results of the numerical calculations are in a good agreement with the experimental data.     

Laser and plasma nitriding of titanium using CW-CO2 laser in the atmosphere

Surface nitriding of the titanium by the mixing technology with laser and plasma (LPN) in atmosphere has been investigated. Comparing with the technique of laser nitriding, we could obtain the titanium nitride at relatively low laser power density and the oxidation was prevented without the chamber. The synthesized layers comprised of titanium nitrides were about 178 μm depth. The effect of the laser power density, scanning velocity, and plasma flow rate on the components consisting of the material of the nitrided layer was studied. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to reveal the components consisting of the material of the nitrided layer.     

Effect of water vapour on particulate matter emission during oxyfuel combustion of char and in situ volatiles generated from rapid pyrolysis of chromated-copper-arsenate-treated wood

This paper reports the effect of water vapour on particulate matter (PM) during the separate combustion of in situ volatiles and char generated from chromated-copper-arsenate-treated (CCAT) wood at 1300 °C. Combustion of in situ volatiles produces only PM with aerodynamic diameter?<1?µm (i.e., PM₁), dominantly PM with aerodynamic diameter?<0.1?µm (i.e., PM_0.1). Water vapour could significantly enhance the nucleation, coagulation and condensation of fine particles and reduce the capture of Na and K by the alumina reactor tube via reduced formation of alkali aluminates, leading to increases in both yield and modal diameter of PM_0.1. Water vapour could also enhance char fragmentation hence increase the yield of PM with aerodynamic diameter between 1 and 10?µm (i.e., PM_1–10) during char combustion. For trace elements, during in situ volatiles combustion, volatile elements (As, Cr, Ni, Cu and Pb) are only presented in PM₁ and water vapour alters the particle size distributions (PSDs) but has little effect on the yields of these trace elements. During char combustion, As, Cr, Cu and Ni are present in both PM₁ and PM_1–10 while the non-volatile Mn and Ti are only present in PM_1–10. Increasing water vapour content increases the yields of As, Cr, Cu, Ni, Mn and Ti in PM_1-10 due to enhanced char fragmentation. During char combustion, water vapour also originates less oxidising conditions locally for enhancing As release, promotes the generation of gaseous chromium oxyhydroxides and inhabits the production of NiCl₂ (g), leading to increased yields of As and Cr and decreased yield of Ni in PM_0.1.     

Characteristics of chars formed during rapid pyrolysis of biomass model components at high temperature

This paper reports char formation and inherent inorganic transformation during rapid pyrolysis of various biomass model components under simulated pulverized fuel (PF) conditions at 1300 °C. A drop-tube furnace with a novel double-tube configuration was deployed to achieve direct determination of char yield. The results show that rapid pyrolysis of xylan and water-washed lignin (W-L) under the conditions results in char yields of 3.4 wt.% and 12.6 wt.%, respectively, while no char was founded during rapid pyrolysis of water-washed cellulose (W-C). After loading K₂CO₃ into the W-C (i.e. KW-C) and W-L (i.e. KW-L), the char yields increase to 2.1 wt.% and 15.6 wt.%, respectively. The retentions of Na and S are low in chars after pyrolysis. After rapid pyrolysis, W-L and KW-L chars have higher retentions of AAEM species than xylan, W-C and KW-C chars. Micromorphology analysis shows char particles formed after rapid pyrolysis of all biomass components have a cenospheric structure and a rough surface with many bubbles and pores, demonstrating strong melting processes. For xylan and KW-L, the abundant inorganics accelerate char formation with swelling and reduce the extent of particle shrinkage, resulting in char particles with apparent sizes bigger than the parent feedstock particles. Oppositely, for KW-C and W-L that have low contents of inorganic species, the pyrolyzing particles experience significant shrinkage, resulting in formed char particles with apparent sizes that are much smaller than feedstock particles.     

Hole capture rate of GaInAs/InP strained quantum-well lasers

The property of hole capture of quantum wells is important in the static properties of lasers above threshold, such as the differential efficiency and light output power. We investigate experimentally the hole capture rate and its influence on the carrier overflow in the optical confinement layers for compressive-strained, tensile-strained and unstrained GaInAs/GaInAsP/InP quantum-well lasers emitting at 1.5 m by measuring the spontaneous emission from the optical confinement layers above threshold. The carrier density in the optical confinement layers increases with current owing to finite hole capture rates. This increase is dependent on well thickness and barrier height determined by the strain. This increase is comparable in the tensile-strained and unstrained lasers with relatively low threshold, while in the compressive-strained laser it is about double that in the other two types. The dependence of this increase on threshold carrier density is also observed, that is the carrier density in the optical confinement layers increases rapidly in high-threshold samples, in particular, in the tensile-strained laser with large hole barrier height. From these results, laser operation with high output power and high efficiency is expected by reducing threshold carrier density in the tensile-strained laser and by increasing well numbers in the compressive-strained laser as long as the inhomogeneous injection between wells is not severe. By fitting measurements with theory, the hole capture time is estimated as 0.1 to 0.25 ps in these strained and unstrained lasers.     

Laser-Induced Graphitic Carbon with Ultrasmall Nickel Nanoparticles for Efficient Overall Water Splitting

Metal nanoparticles encapsulated in graphitic carbon can show high catalytic efficiency and stability, yet the production method remains improved. Herein, it is demonstrated that a Ni-based metal–organic framework [EG-MOF-74(Ni)] can be rapidly transformed into ultrasmall Ni-nanoparticles with different sizes (4–11 nm) encapsulated in graphitic carbon via the laser-scribing method. The synthesized sample shows the best electrocatalytic performances with excellent stability in alkaline electrolyte for oxygen/hydrogen evolution reactions with overpotentials of 0.35/0.18 V at a current density of 10 mA cm⁻² when the Ni particle size is ≈6 nm. This is because of its well-developed micro/mesoporous structure, high electronic transport, and large electrochemical active surface area. An electrolyzer with Ni-nanoparticles encapsulated in the graphitic carbon shows a current density of 10 mA cm⁻² at a voltage of 1.6 V, which is comparable to the Pt/C and RuO₂ counterparts. The laser-based synthesis can serve as a powerful tool for the size-controlled synthesis of various catalysts out of MOFs.     

Ni/Ni3Al interface: A density functional theory study

The optimal geometries, mechanical and thermal properties, and electronic structures of the three low index (0 0 1), (1 1 0), (1 1 1) Ni/Ni₃Al thin film were studied using first principle calculations. Simulated results indicated that Ni and Al atoms in γ^′ phase preferred to place in the hollow site of Ni atoms in γ phase. In hollow site models, electronic states affected by interface localize within 2 atomic layers. While the top site model, electronic states localize within 3 atomic layers. It is also found that hollow site (1 1 0) interface has the best mechanical properties. Hollow site (0 0 1) interface is the most easily formed interface, which has the best thermodynamic properties.