Tunable dual-wavelength fiber laser based on an opto-VLSI processor and four-wave mixing in a photonic crystal fiber

A stable wavelength and wavelength spacing tunable dual-wavelength fiber laser based on an Opto-very-large-scale-integration (Opto-VLSI) processor and four-wave mixing (FWM) in a high-nonlinear photonic crystal fiber is experimentally demonstrated. The results show that the line width of the tunable dual-wavelength fiber laser is 0.02 nm, and the wavelength spacing can be tuned from 0.8 nm to 4 nm with a 0.15 nm step. Under the influence of the FWM, the uniformity is below 0.6 dB and the measured side mode suppression ratio (SMSR) is above 45 dB.     

Widely tunable compact erbium-doped fiber ring laser for fiber-optic sensing applications

A compact erbium-doped ring-shaped fiber laser suitable for fiber-optic sensing applications has been developed. The fiber laser utilized a tunable fiber Fabry–Perot filter as the tuning element and had a moderate milli-Watt level power output over almost the whole tuning range from 1530 to 1595 nm with a power fluctuation of 0.15 dB. High repetition rate scanning of laser operation over the whole tuning range was achieved at rates of up to 200 Hz. Moreover, the performance of the ring-shaped fiber laser configured with a high-concentration erbium-doped fiber was investigated for its larger wavelength tunability of over 100 nm. Output power characteristics of this ring-shaped fiber laser were also investigated when it worked in a scanning mode. A distorted power wavelength dependence, as well as some pulsing phenomenon were observed in scanning mode.     

Flat and compact switchable dual wavelength output at 1060 nm from ytterbium doped fiber laser with an AWG as a wavelength selector

A dual-wavelength ytterbium doped fiber laser with a narrowest spacing of 0.53 nm and widest spacing of 12.2 nm at 1064 nm is presented in this paper. An arrayed waveguide grating (AWG) together with an optical channel selector (OCS) have also been incorporated in the proposed setup that works as a switchable mechanism giving 23 different wavelength tunings. Producing an average output power of ?8 dB m and side mode suppression ratio (SMSR) of 59.65 dB, this dual-wavelength fiber laser is quite stable with an output power variance as low as 0.47 dB giving it an advantage due to its switching ability and stable dual-wavelength output powers.     

Tunable multi-wavelength fiber laser based on a polarization-maintaining erbium-doped fiber and a polarization controller

A stable and tunable multi-wavelength fiber laser with a polarization-maintaining erbium-doped fiber (PM-EDF) and a polarization controller (PC) is proposed and demonstrated. A homemade PM-EDF incorporated in the ring cavity is used as the gain medium. Simultaneous multi-wavelength oscillation is achieved at room temperature. The theory of the PM-EDF and PC to suppress the wavelength competition is described in detail. The 3 dB bandwidth is less than 0.01 nm. The power fluctuation and wavelength shift are measured to be less than 0.5 dB and 0.05 nm over 32 min. The wavelength tuning between single-, double-, triple-, and four-wavelength is realized.     

Synchronous tunable wavelength spacing dual-wavelength SOA fiber ring laser using Fiber Bragg grating pair in a hybrid tuning package

A Dual-Wavelength Semiconductor Optical Amplifier (DW-SOA) based fiber ring laser with synchronous wavelength tunability is proposed and experimentally demonstrated. The SOA gain medium strongly suppresses mode competition, thus allowing stable dual-wavelength laser oscillation. The wavelength spacing of the two lasers can be tuned synchronously using a modified hybrid-tuning package incorporating a pair of Fiber Bragg Gratings (FBGs). The DW-SOA demonstrates a laser output with a wavelength spacing of between 0.10 and 8.30 nm (wavelength shift inequality of 0.08 to 0.75 nm). The relationship between the applied strain and wavelength shift of the two tuning modes is also analyzed.     

Multi-wavelength bismuth-based erbium-doped fiber laser based on four-wave mixing effect in photonic crystal fiber

A stable multi-wavelength erbium-doped fiber laser based on four-wave mixing (FWM) in a photonic crystal fiber (PCF) is demonstrated in this paper. The phase matching condition for four-wave mixing in the photonic crystal fiber has been enhanced using a seed signal and a polarisation controller to control the states of polarisation in the ring laser cavity. At a maximum pump power of 1480 nm, 5 lines are observed with nearly 2.15 nm spacing between the lines, and with a signal to noise ratio of more than 20 dB. The number of channels and wavelength spacing can be controlled by varying the output coupler ratio.     

An energy-efficient tie-type architecture for stable and wavelength-tunable SOA-based fiber laser

A new and energy-efficient tie-type architecture for stable and wavelength-tunable semiconductor optical amplifier (SOA)-based fiber ring laser is proposed and experimentally investigated. Here, the tie-type laser configuration is constructed by two Sagnac fiber loops. The proposed laser also can extend the lasing wavelength to longer wavelength (L-band) even only the C-band SOA is used. The proposed tie-type architecture has >5 dB higher output optical power at bias current of 80 mA when compared with the single ring SOA-based fiber laser. In this measurement, the output power, wavelength tuning range, side-mode suppression ratio (SMSR) and output stability of proposed fiber laser have also been analyzed and discussed.     

Dual-wavelength narrow-linewidth fiber laser based on F-P fiber ring filter

A dual-wavelength fiber laser with a narrow-linewidth, based on a P-F fiber filter has been proposed. Polarization-maintaining fiber Bragg grating (PM-FBG) and a F-P fiber filter are introduced based on the traditional fiber laser. PM-FBG is used as the wavelength selection device. The fiber F-P filter consists of two optical couplers and a section of un-pumped erbium-doped fiber (EDF). Due to the delay of cavity and the loss generated by the EDF, the filter has comb spectral response. The incorporation of the fiber F-P filter leads to the suppression of undesirable modes. At the room temperature, under 980 nm LD pumped, the maximum output of the two wavelengths is respectively ?2.259 dBm and 0.568 dBm, with the 3-dB bandwidth separately 0.1 nm and 0.14 nm, realizing the narrow linewidth and dual-wavelength output.     

Low-threshold all-fiber 1000 nm supercontinuum source based on highly non-linear fiber

We present an highly efficient all-fiber compact supercontinuum source that exhibits a nearly flat spectrum from 1.1 μm to 2.1 μm. This broadband infrared optical source is made-up of a highly non-linear fiber pumped by a 1.55 μm self-Q-switched Er-Brillouin nanosecond pulsed fiber laser, which in turn is pumped by a low-power 1480 nm laser diode. In this work we highlight the great potential of highly non-linear fiber for supercontinuum generation with respect to conventional dispersion-shifted fiber by demonstrating a significant 10 dB power enhancement in the short wavelength side of the supercontinuum.     

Tunable single-longitudinal-mode operation of a sandwich-type YAG/Ho:YAG/YAG ceramic laser

We present a 2.09 μm single-longitudinal-mode sandwich-type YAG/Ho:YAG/YAG ceramic laser pumped by a Tm-doped fiber laser for the first time. A pair of F-P etalons was used to achieve tunable single-longitudinal-mode operation. The maximum single-longitudinal-mode output power of 530 mW at 2091.4 nm was obtained with an absorbed pump power of 8.06 W, corresponding to an optical conversion efficiency of 6.6% and a slope efficiency of 12.7%. Wavelength tunable was achieved by tuning the angle of etalons and the wavelength could be tuned from 2091.1 nm to 2092.1 nm, corresponding to a tuning frequency of 68 GHz. The M² factor was measured to be 1.23.     

Adjustable EDFA gain equalization filter for DWDM channels based on a single LPG excited by flexural acoustic waves

A fast adjustable gain equalization filter for dense wavelength division multiplexing (DWDM) system is reported. The method is based on a single long period fiber grating (LPG) which is excited by means of flexural acoustic waves. The equalization of a typical erbium doped fiber amplifier (EDFA) gain spectrum with a gain flatness of <0.3 dB over a 32 nm bandwidth is demonstrated. The filter adjustment is obtained by choosing different acoustic loads applied to the acousto-optic modulator, which presents a switching time of ～17 μs. A maximum power penalty of 0.84 dB, relatively to the back-to-back signal, was achieved.     

Tunable single-longitudinal-mode Ytterbium all fiber laser with saturable-absorber-based auto-tracking filter

A broadband tunable, single-longitudinal-mode (SLM) Ytterbium fiber laser with unpumped Ytterbium-doped Sagnac loop is proposed and demonstrated experimentally. The unpumped Ytterbium-doped Sagnac loop is employed as a saturable absorber based auto-tracking filter to ensure single-longitudinal-mode oscillation. And a tunable band pass optical filter with large tuning range is applied to achieve broadband tuning ability. With 1-m Ytterbium-doped fiber as the gain medium, the SLM operation is achieved with over 60-nm wavelength tuning range at 160-mW pump power. The laser is very stable with output power of about 3 dBm and optical signal to noise ratio of higher than 50 dB in all the 60-nm tuning range.     

A novel OCS millimeter-wave generation scheme with data carried only by one sideband and wavelength reuse for uplink connection

We propose a novel optical carrier suppression (OCS) millimeter-wave generation scheme with data carried only by one sideband using a dual-drive Mach–Zehnder modulator (MZM) in radio-over-fiber system, and the transmission performance is also investigated. As the signal is transmitted along the fiber, there is no time shifting of the codes caused by chromatic dispersion. Simulation results show that the eye diagram keeps open and clear even when the optical millimeter-waves are transmitted over 110 km and the power penalty is about 1.9 dB after fiber transmission distance of 60 km. Furthermore, due to the +1 order sideband carrying no data, a full duplex radio-over-fiber link based on wavelength reuse is also built to simplify the base station. The bidirectional 2.5 Gbit/s data is successfully transmitted over a 40 km standard single mode fiber with less than 0.8 dB power penalty in the simulation. Both theoretical analysis and simulation results show that our scheme is feasible and we can obtain a simple cost-efficient configuration and good performance over long-distance transmission.     

Polarization-independent rapidly tunable optical add-drop multiplexer utilizing non-polarizing beam splitters in Ti:LiNbO3

A polarization-independent four-port wavelength-tunable optical add drop multiplexer (OADM) that utilizes non-polarizing relaxed beam splitters has been analyzed and demonstrated in Ti:LiNbO₃ at the 1530 nm wavelength regime. The design utilizes an asymmetric interferometer configuration with strain induced index grating for polarization coupling along its arms that are shifted in position relative to each other. Experimental results of the filter response agree with theoretical predictions. Electrooptic tuning over a range of 15.7 nm at a rate of 0.08 nm/V has been measured. A temporal response < 46 ns to a 20 V step change in tuning voltage has been demonstrated. Fiber-to-fiber insertion loss is ~ 6.5 dB.     

A linearly-polarized tunable Yb-doped fiber laser using a polarization dependent fiber loop mirror

A Ytterbium-doped linearly-polarized fiber laser is constructed with a polarization maintaining fiber Sagnac loop mirror. The fiber loop mirror made of polarization maintaining fiber coupler has a polarization dependent reflectivity, which provides the necessary polarization discrimination between the slow and fast axes. With a fiber Bragg grating written in normal polarization maintaining fiber as an output coupler, laser output of up to 5.6 W at 1070 nm is generated with a polarization extinction ratio of > 20 dB and an overall efficiency of 55%. The broadband polarization dependent reflection of the fiber loop mirror offers advantages of easy spectral tuning and simple linearly-polarized laser generation.     

Compact resonantly intra-cavity pumped tunable Ho:Sc2SiO5 laser

A compact intra-cavity pumped low threshold continuous-wave Ho:Sc₂SiO₅ laser is reported. The characteristics of output wavelength tuning are investigated by use a intra-cavity briefringent (BF) filter. A wavelength tunable range of 140 nm from 2020 to 2160 nm is achieved. For the free-running mode, the laser slope efficiency is 24.8%, when the output central wavelength is 2110 nm. The laser threshold is about 820 mW of incident pump power. With the BF filter, a maximum output power of 870 mW is obtained at the incident pump power of 5 W, corresponding to a slope efficiency of 20.3%. The characteristics of output wavelength verse the crystal temperature are also investigated.     

Dual-stage L-band erbium-doped fiber amplifier with distributed pumping from single pump laser

A dual-stage L-band erbium-doped fiber amplifier with a flat gain bandwidth over 36 nm is demonstrated using pump distribution technique. The pump power was distributed to two stages depending on the splitting ratio and the length of erbium-doped fiber that was used for this configuration. Both parameters are the key components for achieving a substantially flat gain response throughout the L-band region ranging from 1570 nm to 1605 nm. Although the input signal power was varied from ? 30 dBm to 0 dBm, gain of 17 dB with slight variations of less than 1.5 dB and a noise figure of less than 6.7 dB were achieved. All the results obtained show better performances when comparison was made with the conventional single-stage L-band optical amplifier.     

Switchable single- and dual-wavelength erbium-doped fiber laser assisted by four-wave mixing with wide and continuous tunability

A widely tunable and stable erbium-doped fiber laser based on four-wave mixing effect in a highly nonlinear fiber is proposed and experimentally demonstrated. By adjusting reflected power from a dual-selective element, the ring laser is switchable between single- and dual-wavelength operations. The tuning range of the single laser is 22.78 nm, from 1,542.07 to 1,564.85 nm, while the wavelength spacing of the dual-wavelength can be continuously tuned from 0.52 to 22.78 nm. The laser is stable with output peak power fluctuation of <1 dB in 30-min interval.     

High-power single-longitudinal-mode operation of Tm:YAG laser using Fabry–Perot etalons and volume Bragg grating

A diode-pumped high-power single-longitudinal-mode (SLM) Tm:YAG laser was investigated. To obtain a single-frequency 2 μm laser output, Fabry–Perot (F–P) etalons combined with a volume Bragg grating (VBG) were used as frequency selection devices. The transmission losses of the VBG and etalons were analyzed and the angles of F–P etalons were optimized theoretically. Considering the gains and the insertion losses, the output wavelength of the Tm:YAG laser was estimated to be 2012.47 nm. Using this method, as much as 574 mW SLM laser was obtained experimentally, corresponding to a slope-efficiency of 18.6% and an optical-to-optical efficiency of 8.2%. The output wavelength was measured to be 2012.47 nm, which was in excellent agreement with the theoretical result. The power instability was less than 1% in 30 minutes test, and the degree of the linear polarization was over 20 dB.     

Inherently gain flattened S-band erbium doped fiber amplifier based on dual core resonant leaky fiber

A co-axial dual core resonant leaky optical fiber (DCRLF) is designed for inherent gain equalization of S-band erbium doped fiber amplifier (EDFA). Resonance tail of leakage loss of the fiber into the S-band region is utilized to flatten the gain. We have numerically studied the effect of various design parameters and their fabrication tolerances on gain flattening. We show 23.5 dB flat gain with ± 0.9 dB ripple over 30 nm bandwidth (1490–1520 nm) using 120 mW pump. The study should be useful in designing optical fiber amplifiers for optical communication system employing wavelength division multiplexing.