光通信链路中集成芯片的收发一体工作

在PIN光电探测器(PIN-PD)结构的垂直方向上集成垂直腔面发射激光器(VCSEL)结构单元,实现了收发一体式工作的集成光电芯片对,可用于进一步提高光互连的性能。该集成光电芯片可以同时对两个波段进行收发一体工作,一端进行中心波长为805 nm的光信号的发送和中心波长为850 nm的光信号的接收,另一端进行中心波长为850 nm的光信号的发送和中心波长为805 nm的光信号接收。仿真优化805 nm波长处光信号发送端的结构与性能,理论分析结构中VCSEL单元和PIN-PD单元工作时的电学隔离和光学解耦,最终证实本结构可以同时进行收发一体的工作。     

波长可调谐的瓦级连续橙红光激光器

介绍了基于复合腔结构的全固态波长可调谐的连续橙红色激光的输出特性。该复合腔由一个使用周期极化晶体MgO:PPLN的信号光单谐振光参量振荡器和一个LD侧面泵浦Nd:GdVO₄晶体的1 062.9 nm基频光谐振腔构成。s-偏振1 062.9 nm泵浦光抽运单谐振光参量振荡器产生s-偏振信号光腔内独立振荡。通过复合腔结构的优化设计,使独立振荡的p-偏振1 062.9 nm基频光与s-偏振信号光在2个子腔的重叠区内通过Ⅱ类角度匹配KTP晶体的腔内和频过程获得橙红色激光。当MgO:PPLN晶体的调谐温度从30 ℃上升至200 ℃时,s-偏振信号光的中心波长产生红移,导致其与p-偏振1 062.9 nm基频光和频产生的橙红色激光的中心波长从620.2 nm红移至628.9 nm。同时测得中红外波段闲频光的中心波长从3 714.2 nm蓝移至3 438.3 nm。在30 ℃最低设定温度时, 中心波长620.2 nm的橙红色激光和中心波长3 714.2 nm的闲频光最大连续输出功率分别达到2.0 W和2.9 W。     

基于半导体光放大器瞬态交叉相位调制效应的高速反相和同相波长转换的研究

采用半导体光放大器(SOA)中的瞬态交叉相位调制效应是实现高速全光信号处理的有效途径.利用SOA和带宽为0.4 nm的窄带滤波器同时实现了重复频率为10 GHz、脉冲宽度为10 ps的同相和反相全光波长转换.当滤波器的中心波长相对于探测光载波波长蓝移0.25 nm或者红移0.05 nm时，得到反相波长转换；当滤波器的中心波长相对于探测光波长蓝移0.29 nm或者红移0.25 nm时，得到同相的波长转换.同时用数值模拟了从同相到反相波长转换的极性演化过程，理论分析和实验结果基本相符. 关键词： 半导体光放大器 波长转换 瞬态交叉相位调制     

基于光纤光栅辅助耦合的WDM下话路研究

利用光纤光栅的反射特性和光纤耦合器的耦合特性,研究基于光纤光栅辅助耦合波分复用(WDM)下话路器.满足国际电信联盟(ITU-T)建议波长的WDM光信号从耦合器输入端口进入,其中与光栅中心反射波长一致的激光信号从耦合器的下话路端口输出,而其他波长的激光信号从耦合器输出端口输出,实现特定波长信号的下话路.选择中心波长分别为1554.248 nm,1555.859 nm,消光比为57 dB的两路光信号进行试验,光纤光栅的中心反射波长为1555.86 nm,实验结果表明,上述两路光信号分别从不对称光纤耦合器的输出端口和下话路端口输出,且在下话路端口输出光信号的消光比为48 dB.     

金膜上亚波长周期性孔阵的模拟与研制

分析了980 nm波长的光在透过制作在金膜上的亚波长周期性孔阵时的透射增强现象.通过建立中心带缺陷孔的三角晶格的孔阵模型,并采用三维时域有限差分方法对该模型的透射情况进行模拟分析.结果表明通过优化孔阵周期参数可以对特定波长的光实现一定程度的选择透过性.当孔阵周期为450 am,中心缺陷孔径为400 nm,孔阵中单个孔孔径为150 nm时,980 nm波跃光透过该孔阵时具有明显的透射增强效应,并且距孔阵表面3μm的远场光斑尺寸被局限在亚波长尺度(880 nm).研究了使用聚焦离子束在金膜上制备孔阵的工艺,成功研制了与没计尺寸一致的孔阵.这种孔阵可以集成在980 nm垂直腔面发射激光器上,用于改善器件的远场光学特性.     

LiNbO3∶Cr∶Cu晶体吸收特性及非挥发全息存储研究

研究了LiNbO3∶Cr∶Cu晶体的吸收特性,发现LiNbO3∶Cr∶Cu（含0.14 wt.% Cr2O3 和 0.011 wt.% CuO）晶体存在两个明显的吸收峰,中心波长分别位于480 nm和660 nm; 随着Cr的含量逐渐减小,Cu的含量逐渐增大,短波段不存在明显吸收峰,掺Cr的含量越大,中心波长在660 nm处的吸收越大；633 nm红光虽然位于中心波长为660 nm的吸收峰内,但它无助于光折变过程.分别采用390 nm紫外光和488 nm蓝光作为敏化光,514 nm绿光作为记录光的记录方案,实现了非挥发全息记录,掺入适量的Cr( 比如NCr=2.795×1025 m－3,NCr/ NCu=1)有助于全息记录性能的提高.     

LiNbO_3∶Cr∶Cu晶体吸收特性及非挥发全息存储研究

研究了LiNbO3∶Cr∶Cu晶体的吸收特性,发现LiNbO3∶Cr∶Cu(含0.14wt.%Cr2O3和0.011wt.%CuO)晶体存在两个明显的吸收峰,中心波长分别位于480nm和660nm;随着Cr的含量逐渐减小,Cu的含量逐渐增大,短波段不存在明显吸收峰,掺Cr的含量越大,中心波长在660nm处的吸收越大;633nm红光虽然位于中心波长为660nm的吸收峰内,但它无助于光折变过程·分别采用390nm紫外光和488nm蓝光作为敏化光,514nm绿光作为记录光的记录方案,实现了非挥发全息记录,掺入适量的Cr(比如NCr=2.795×1025m-3,NCr/NCu=1)有助于全息记录性能的提高·     

结合波分复用和空分复用的光纤光栅串口总线式检测系统

结合波分复用和空分复用技术,可增加光纤Bragg光栅(FBG)传感波长的解调数目。开发了FBG传感器检测仪与计算机系统之间的光纤Bragg光栅传感检测系统。该系统通过串口总线分别与光开关和解调仪通信,实现了传感光谱的实时描绘和16通道的FBG传感中心波长的动态更新。测试结果表明,系统工作波长范围为1527~1566nm,中心波长分辨率为1pm,一次采集光栅波长信息时间为620ms。     

Eu:Fe:LiNbO3晶体非简并四波混频的研究

用波长为623.8nm的He-Ne激光作信号光和一束泵浦光,用波长为488.0nm的Ar⁺激光作另一束泵浦光,在Eu:Fe:LiNbO₃晶体中实现了非简并四波混频,获得了波长为488.0nm的变频相位共轭光,同时还产生了波长为632.8nm的同频相位共扼光。本文对上述实验结果进行了定性分析。     

基于Y型分支与布拉格光栅结构的集成光芯片研究

采用Y型分支与深刻蚀布拉格波导光栅相集成的方案,制备了带有通道监控功能的1×8光分路器集成芯片。耦合封装后的集成光芯片同时实现了稳定的通道光信号传输与监控功能。集成光芯片8通道反射谱中心波长范围为1 597 nm～1 639 nm,间隔为6 nm,3 dB带宽最大为0.67 nm,通道反射率最低为88.24%。1 550 nm波长下测试8通道的平均插损为11.92 dB,输出均匀性为0.19 dB。本文设计并制备的集成光芯片结构简单、集成化高,可以应用于光纤到户建设及其他光网络传输中,实现网络链路状态的实时监控。     

LD泵浦355nm准连续紫外激光器

报道了一台LD侧面泵浦Nd:YAG晶体的内腔三次谐波转换的全固态准连续紫外激光器。在谐振腔内,1064nm的基频波通过对Ⅱ类相位匹配KTP晶体进行二倍频来产生532nm波长激光,二者再通过对Ⅱ类相位匹配LBO晶体进行和频来获得355nm紫外激光输出。355nm全固态紫外激光器在声光调Q重复频率为2.8kHz下,当输入电流为18A时可得到503mW的激光输出。     

The Fabrication and SHG Test of QPM Periodically Poled KTiOPO4

The Quasi-phase-matching periodically poled flux-grown KTP by high electrical field method is researched. A 8×5×1mm3, Λ=9.0μm PPKTP wafer is successfully fabricated for the first order QPM SHG. The interactive length of the sample is about 3mm. The SHG scheme of Nd:YAG at 1064nm tested that the output power of cw 532nm green light is 0.2mw at room temperature with fundamental power of 1.2w. The normalized conversion efficiency is about 0.09% (W·cm)-1.     

基于单块周期极化铌酸锂晶体级联三倍频的440 nm蓝光固体激光器

阐述了一种基于单块周期极化铌酸锂晶体级联三倍频实现440 nm蓝光输出的实验方案。根据周期极化铌酸锂晶体的Sellmeier方程以及倍频与和频的相位匹配条件,在一块周期极化铌酸锂晶体上设计了两段不同的极化周期,使其在同一工作温度下能分别实现倍频与和频,在先后经过倍频与和频后,实现级联三倍频输出。实验采用Nd: YAG产生的1319 nm光作为基频光,重频400 Hz,脉宽110 ns,横向和纵向光束质量因子分别为1.81和2.65。耦合进周期极化铌酸锂晶体后,出射光中检测到660 nm的红光和440 nm的蓝光。通过调整工作温度和入射基频光功率,得到2.4 mW的最大蓝光输出,此时工作温度55.5 ℃,基频光功率530 mW。实验结果验证了单块晶体实现级联三倍频440 nm蓝光输出的可行性。     

LD-pumped Nd:YAG/LBO 556 nm yellow laser

A new laser transition at 1112 nm was obtained after analyzing the parameters of the main laser transitions in Nd:YAG and calculating the transmission loss of the cavity at 1064, 1319, and 946 nm. The maximum output power of the fundamental wavelength was 610 mW, the fundamental wavelength light-to-light conversion efficiency was 38.1%, the maximum output at 556 nm was 109 mW intra-cavity frequency doubled by LBO, the SHG conversion efficiency was 17.8%, and the overall light-to-light efficiency was 6.8% for the pump power of 1.6 W.     

Miniaturized highly brilliant diode laser modules for future display applications

We demonstrate diode laser modules with high spectral radiance larger than 1 GW/cm²/sr/nm in the visible spectral range. These highly brilliant laser light sources enable the development of next-generation 3D displays. About 1W output power from small-sized modules was achieved at 635 nm by direct diode laser emission and at 530 nm using single pass second harmonic generation (SHG) of a highly brilliant near-infrared laser diode.     

高能量高转换效率355 nm紫外激光器

为了得到一种三倍频效率高达60%的355 nm脉冲激光器,采用曲率半径分别为2 m的凹凸高斯镜和9 m的平凹全反镜组合作为谐振腔,加以电光调Q,得到1 064 nm高光束质量激光输出,再将其进行行波放大,获得重复频率10 Hz、脉宽7.3 ns、单脉冲能量1.01 J的1 064 nm基频光输出。利用Ⅰ类相位匹配LBO晶体进行二倍频、Ⅱ类相位匹配LBO晶体进行三倍频以得到波长为355 nm的紫外光输出。通过二倍频和三倍频输出特性和非线性晶体参数的分析和实验调试,最终获得了单脉冲能量为608 mJ、脉宽为5.7 ns、线宽为2 nm的紫外激光输出。通过优化二倍频的转换效率,可使1 064 nm基频光到三倍频得到的355 nm紫外光的转换效率达60%。     

Investigation on high efficiency temporal phase modulated broadband second harmonic laser

In this paper, it is the first time to experimentally demonstrate the second harmonic generation (SHG) of temporal phase modulated broadband laser. The SHG conversion efficiency and the characteristic of SHG spectrum are investigated in detail and the relation between SHG conversion efficiency and incident fundamental light intensity is obtained. The highest efficiency of nearly 70% is achieved at the fundamental pulse intensity of 1.6 GW/cm². The experimental results show that the SHG spectrum widths under high and low intensity are both half of the incident fundamental lights, and don’t result in the spectrum narrowing. The obtained results are very useful for operation at the second harmonic wavelength in inertial confinement fusion (ICF) laser facility.     

Second harmonic generation by femtosecond Yb-doped fiber laser source based on PPKTP waveguide fabricated by femtosecond laser direct writing

The frequency doubling of femtosecond pulses from an Yb-doped fiber laser source was demonstrated in a PPKTP waveguide fabricated by femtosecond laser direct writing. The PPKTP waveguide contains a fixed period of 8.9 μm and the feomtosecond fundamental pulses have a central wavelength of 1044 nm. A maximum SHG power of 406 mW was produced, yielding a conversion efficiency of 5.6%. Numerical simulations were carried out to investigate the property of frequency doubling for femtosecond pulses. The results show that the SHG process proceeds even the quasi-phase-matching (QPM) condition is not well satisfied, which is significantly different from that of “long” pulses or CW light and is accorded with the experimental results.     

A compact and high efficiency diode pumped green laser based on MgO doped PPLN

In this work, an efficient intra-cavity second harmonic generation of green laser in a periodically poled MgO doped LiNbO₃ (MgO:PPLN) bulk crystal using a compact Nd:YVO₄ laser as a fundamental laser source is reported. Different length, different working temperature MgO:PPLN crystals are tested and investigated in the SHG experiments. The maximum output power at 532 nm is 6.2 W at the absorbed pump power at 808 nm of 14 W, the optical to optical conversion efficiencies from 808 to 532 nm and 1064 to 532 nm are 43 and 77%, respectively, the instability in 2 hours is less than 5%.