Deposition of ZnO multilayer on LiNbO3 single crystals by DC-magnetron sputtering

Zinc oxide (ZnO) thin films were deposited on LiNbO₃ (LN) single crystals with 200 nm thicknesses by three different ways, where coating of zinc (Zn) film was followed by thermal oxidation for four, two, and one steps with 50, 100, and 200 nm thicknesses repeatedly. Sample, which was produced at 4-step of deposition and oxidation of Zn layer, showed high transmittance and low structural defect due to a lower photoluminescence intensity and Urbach energy. Average grain size in X-ray diffraction (XRD), scanning electron microscopy (SEM) micrograph, and atomic force microscopy (AFM) images for multilayer of ZnO was lower than monolayer of ZnO thin films. Applying multilayer coating technique leads to decrease of surface roughness and scattering on light on surface and fabrication of LiNbO₃ waveguides with lower optical loss.     

Plasma-activated core-shell gold nanoparticle films with enhanced catalytic properties

Catalytically active gold nanoparticle films have been prepared from core-shell nanoparticles by plasma-activation and characterized by high-resolution transmission electron microscopy, atomic force microscopy, and X-ray photoelectron spectroscopy. Methane can be selectively oxidized into formic acid with an O₂–H₂ mixture in a catalytic wall reactor functionalized with plasma-activated gold nanoparticle films containing well-defined Au particles of about 3.5 nm in diameter. No catalytic activity was recorded over gold nanoparticle films prepared by thermal decomposition of core-shell nanoparticles due to particle agglomeration.     

Intense ultraviolet upconversion luminescence of Yb and Tb co-doped glass ceramics containing SrF2 nanocrystals

The preparation and upconversion luminescence properties of the Yb³⁺ and Tb³⁺ co-doped glass ceramics containing SrF₂ nanocrystals were investigated. The formation of SrF₂ nanocrystals was confirmed by X-ray diffraction and transmission electron microscopy. Both microstructural and spectral analysis indicated that the Yb³⁺ and Tb³⁺ ions were enriched in the precipitated SrF₂ nanocrystals, which provide much lower phonon vibration energy than the glass matrix. Due to the efficient cooperative sensitization from Yb³⁺ to Tb³⁺ and the relatively low maximum phonon energy of SrF₂ nanocrystals, the Yb³⁺ and Tb³⁺ co-doped glass ceramics exhibited intense upconversion luminescence, including ultraviolet emission at 382 nm.     

The film thickness dependent thermal stability of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>:Ag thin films as high-temperature solar selective absorbers

The monolayer Al₂O₃:Ag thin films were prepared by magnetron sputtering. The microstructure and optical properties of thin film after annealing at 700 °C in air were characterized by transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and spectrophotometer. It revealed that the particle shape, size, and distribution across the film were greatly changed before and after annealing. The surface plasmon resonance absorption and thermal stability of the film were found to be strongly dependent on the film thickness, which was believed to be associated with the evolution process of particle diffusion, agglomeration, and evaporation during annealing at high temperature. When the film thickness was smaller than 90 nm, the film SPR absorption can be attenuated until extinct with increasing annealing time due to the evaporation of Ag particles. While the film thickness was larger than 120 nm, the absorption can keep constant even after annealing for 64 h due to the agglomeration of Ag particles. On the base of film thickness results, the multilayer Al₂O₃:Ag solar selective thin films were prepared and the thermal stability test illustrated that the solar selectivity of multilayer films with absorbing layer thickness larger than 120 nm did not degrade after annealing at 500 °C for 70 h in air. It can be concluded that film thickness is an important factor to control the thermal stability of Al₂O₃:Ag thin films as high-temperature solar selective absorbers.     

Growth of AgInSe<Subscript>2</Subscript> on Si(100) substrate by thermal evaporation technique

AgInSe₂ films were prepared by a thermal evaporation technique onto Si(100) substrates at a pressure of 10⁻⁵ mbar. Structural and optical properties of films deposited at 300 and 473 K have been investigated. The film composition was studied by energy dispersive analysis through X-rays. X-ray diffraction patterns indicate that AgInSe₂ films have chalcopyrite structure with strong preferred orientation in the (112) direction. Average vertical crystallite size of 25 nm was observed. The optical energy gaps of 1.20 and 1.90 eV were obtained due to the fundamental absorption edge and a transition originating from crystal field splitting, respectively. Field emission scanning electron microscopy shows loosely packed grains of spherical symmetry with some facets.     

Ni2+ emission in SrF2

Luminescence measurements of X-irradiated SrF₂:Ni are reported. After X-irradiation two emission bands have been found. One of them peaked at 293 nm and has an excitation band at 267 nm. The other one at about 770 nm, which is much weaker, has an excitation band at 274 nm. Both emission bands are also observed under X-ray excitation. A comparison with some previous studies of the absorption and thermoluminescence properties of X-irradiated SrF₂:Ni indicates that the emission bands are due to two different kinds of Ni²⁺ centers. The proposed emission mechanisms are similar to those found in CaF₂:Ni.     

Growth of β-Ga2O3 nanobelts on Ir-coated substrates

We demonstrate the production of gallium oxide (Ga₂O₃) nanobelts on iridium (Ir)-coated substrates by thermal evaporation of GaN powders. Scanning electron microscopy revealed that the product consisted of nanobelts with widths in the range of 100–700 nm and thicknesses less than 1/5 of the widths. X-ray diffraction and high-resolution transmission electron microscopy indicated that the nanobelts have the single-crystalline monoclinic structure of Ga₂O₃. The photoluminescence spectrum under excitation at 325 nm showed a broad band with a prominent emission peak around 433 nm.PACS 81.07.-b     

Nd:YAG laser synthesis of nanostructural V2O5 from vanadium oxide sols: Morphological and structural characterizations

Vanadium oxide thin films were prepared by sol-gel method, then subjected to Nd:YAG laser (CW, 1064 nm) radiation. The characteristics of the films were changed by varying the intensity of the laser radiation. The nanocrystalline films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). XRD revealed that above 102 W/cm² the original xerogel structure disappears and above 129 W/cm² the films become totally polycrystalline with an orthorhombic structure. From TEM observations, we can see that due to laser radiation, the originally fibrillar-like particles disappear and irregular shaped, layer structured V₂O₅ particles are created. From XPS spectra we can conclude that due to laser radiation the O/V ratio increased with higher intensities.     

Synthesis and characterization of a polyaniline-modified SnO<Subscript>2</Subscript> nanocomposite

Polyaniline-modified tin oxide and tin oxide nanoparticles were synthesized using a solution route technique. The obtained pristine products were characterized with X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, and optical absorption spectroscopy. Thermogravimetric analysis results showed that the polyaniline-modified SnO₂ nanoparticles exhibit higher thermal stability than the SnO₂ nanoparticles. Scanning electron microscopy analysis on the as-synthesized powders showed spherical particle in the range of 50–100 nm.     

Control of tensile stress on inducing formation and tunability of (100) oriented Pb x Sr1−x TiO3 thin films

(100) Oriented Pb _x Sr_1?x TiO₃ (PSTO) thin films are prepared on indium tin oxide (ITO)/glass substrates by sol–gel technique while inserting doped PbTiO₃ (PTO)-inducing layer in between. The effect of tensile stress in PSTO on tunability and (100) orientation of the thin films was investigated using X-ray diffraction, scanning electron microscopy, transmission electron microscope, and atomic force microscope, respectively. Results show that PSTO thin film deposited on doped PTO has (100) oriented structure while it is randomly oriented when deposited directly on the ITO/glass substrate. Lattice mismatch between PSTO and PTO appears, in which the in-plane lattice constant c is 0.3922–0.3924 nm in the former and 4.02–4.07 nm in the latter, respectively, contributing tensile stress in the PSTO due to different lattice constants between them. The stress in the PSTO thin film is 3.04, 3.15, 3.59 and 4.47 GPa when the doped PTOs are Fe–PTO, Tb–PTO, Co–PTO and Zn–PTO, respectively. The orientation degrees of PSTO thin films are from 89.63, 90.31, 91.92 to 93.29 % with increasing stress of PSTO on Fe–PTO, Tb–PTO, Co–PTO and Zn–PTO, respectively. Tunabilities of the well-oriented PSTO thin films increase in ascending order of 63 < 65 < 69 < 73 % when induced by oriented PTO layers of Fe–PTO, Tb–PTO, Co–PTO and Zn–PTO, respectively, which is in accordance with the degree of (100) orientation appearing in the thin films. The high tunability appears in the PSTO thin film while high (100) orientation is derived from the tensile stress. It is much higher than that of randomly oriented PSTO thin film.     

Effect of internal strain fields on the controllability of nanodimensional ferroelectric films in a plane capacitor

Nanodimensional ferroelectric heteroepitaxial Ba_0.8Sr_0.2TiO₃ films grown by the layer-by-layer mechanism on MgO(100) substrates are examined by the X-ray diffraction and transmission electron microscopy methods. It is established that, when the thickness of the film changes, the stress relaxation proceeds via generation of misfit dislocations at the film-substrate interface. There exists a critical thickness (≈40 nm) of the film below and above which the film possesses tensile and compression stresses, respectively. Examples of how the stresses influence the insulating properties of the films are given.     

Low temperature thermoelectric properties of Cu intercalated TiSe2: a charge density wave material

Y₂O₃ nanoparticles and nanorods have been firstly synthesized in bulk Ti-Y films prepared by magnetron sputtering on Si (100) substrates at different temperatures. X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy (EDS) are used to characterize the structure, morphology, and composition of the as-synthesized nanoparticles and nanorods. The mechanical properties of the sputtered films are investigated using nanoindentation techniques. The results indicate that both the nanoparticles and nanorods have a pure cubic Y₂O₃ structure resulting from the reaction of Y atoms with the residual O₂ in the vacuum chamber, and are free from defects and dislocations with uniform diameters of about 30 nm. The Y₂O₃ nanoparticles mainly distribute at the grain boundaries of the Ti matrix and the nanorods have lengths ranging from 250 nm to more than 1 μm with the growth direction parallel to the (002) plane. As the growth temperature elevates, the nanoparticles turn to be coarsening while more and longer nanorods are inclined to form. Compared with the Ti film, the TiY films have a remarkable increase in hardness, but do not exhibit expected increase in elastic modulus. Finally, the growth mechanism is also briefly discussed.     

ZnSe/SiO2复合薄膜光学常数与荧光光谱的研究

采用溶胶-凝胶工艺与原位生长技术，制备了ZnSe/SiO₂复合薄膜.X射线衍射分 析表明薄膜中ZnSe晶体呈立方闪锌矿结构.X射线荧光分析结果显示薄膜中Zn与Se摩尔比为1 ∶1.01—1∶1.19.利用场发射扫描电子显微镜观察了复合薄膜的表面形貌，结果表明复合薄 膜表面既存在尺寸约为400nm的ZnSe晶粒，也存在尺寸小于100nm的ZnSe晶粒.利用椭偏仪测 量了薄膜椭偏角Ψ，Δ与波长λ的关系，采用Maxwell-Garnett有效介质理论对薄膜的光学 常数、厚度、气孔率、ZnS 关键词： 2复合薄膜')" href="#">ZnSe/SiO₂复合薄膜 光学性质 椭偏光度法 荧光光谱     

Changes of structure and composition of a zinc ion-implanted silicon surface during nanoparticle formation upon thermal treatment

Data from investigating the formation of nanoparticles (NPs) on a surface of silicon wafers after zinc ion implantation and thermal annealing are presented. The investigation is conducted by means of trans-mission electron microscopy, electron diffraction analysis, energy dispersive microanalysis, scanning tunneling microscopy, scanning electron microscopy, and X-ray photoelectron spectroscopy. It is found that on their surfaces, the implanted samples have only films of amorphous silicon containing implanted zinc, oxygen, and carbon contamination. Thermal treatment in the range of 400–800°C leads to the formation NP with 20–50 nm wide and 10 nm tall on a wafer’s surface, plus a silicon oxide layer about 20 nm thick. NPs are composed of zinc compounds of the ZnO, ZnSiO₃, or Zn₂SiO₄ types. These NPs disappear after annealing at 1000°C.     

Synthesis of In-doped Ga2O3 zigzag-shaped nanowires and optical properties

In-doped Ga₂O₃ zigzag-shaped nanowires and undoped Ga₂O₃ nanowires have been synthesized on Si substrate by thermal evaporation of mixed powders of Ga, In₂O₃ and graphite at 1000 °C without using any catalyst via a vapor-solid growth mechanism. The morphologies and microstructures of the products were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS) and photoluminescence spectroscopy (PL). The nanowires range from 100 nm to several hundreds of nanometers in diameter and several tens of micrometers in length. A broad emission band from 400 to 700 nm is obtained in the PL spectrum of these nanowires at room temperature. There are two blue-emission peaks centering at 450 and 500 nm, which originate from the oxygen vacancies, gallium vacancies and gallium-oxygen vacancy pairs.     

A simple and low temperature process for super-hydrophilic rutile TiO2 thin films growth

We investigate an environmentally friendly aqueous solution system for rutile TiO₂ violet color nanocrystalline thin films growth on ITO substrate at room temperature. Film shows considerable absorption in visible region with excitonic maxima at 434 nm. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), UV-vis, water surface contact angle and energy dispersive X-ray analysis (EDX) techniques in addition to actual photo-image that shows purely rutile phase of TiO₂ with violet color, super-hydrophilic and densely packed nanometer-sized spherical grains of approximate diameter 3.15 ± 0.4 nm, characterize the films. Band gap energy of 4.61 eV for direct transition was obtained for the rutile TiO₂ films. Film surface shows super-hydrophilic behavior, as exhibited water contact angle was 7°. Strong visible absorption (not due to chlorine) leaves future challenge to use these films in extremely thin absorber (ETA) solar cells.     

Pulsed laser deposited ZrAlON films for high-k gate dielectric applications

ZrAlON films were fabricated using the reactive ablation of a ceramic ZrAlO target in N₂ ambient by pulsed laser deposition (PLD) technique. ZrAlON films were deposited directly on n-Si(100) substrates and Pt coated silicon substrates, respectively, at 500 °C in a 20 Pa N₂ ambient, and rapid thermal annealed (RTA) in N₂ ambient at 1000 °C for 1 min. Cross sectional high-resolution transmission electron microscopy (HRTEM) images clearly show that the ZrAlON/Si interface is atomically sharp without an interfacial layer, and the films are completely amorphous. The electron diffraction pattern of TEM also indicates the amorphous structure of the RTA ZrAlON film. X-ray photoelectron spectroscopy (XPS) measurement was performed to confirm the effective incorporation of nitrogen with a content of about 6 at. %, and to reveal the N–O bonding in ZrAlON films. The dielectric constant of amorphous ZrAlON was determined to be about 18.2 which is more than 16.8 for ZrAlO by measuring the Pt/films/Pt capacitors. Capacitance–voltage (C–V) measurements show that a small equivalent oxide thickness (EOT) of 1.03 nm for 4 nm ZrAlON film on the n-Si substrate with a leakage current of 28.7 mA/cm² at 1 V gate voltage was obtained. PACS 77.55.+f; 81.15.Fg; 73.40.Qv     

The effect of silicon-substrate orientation on the local piezoelectric characteristics of LiNbO<Subscript>3</Subscript> films

The domain structure of lithium-niobate thin films grown on Si(111) and Si(100) substrates coated with a native oxide layer with a thickness of no less than 2 nm is investigated by X-ray diffraction, scanning electron microscopy and piezoresponse force microscopy. The films are synthesized by the rf magnetron sputtering of a single-crystal lithium-niobate target. A high degree of grain orientation in the polycrystalline films is demonstrated. The piezoelectric coefficients d _zz of the lithium-niobate films on Si(111) and Si(100) substrates are calculated from the measured dependences of the amplitude of the piezoresponse signal on the ac voltage applied between the cantilever tip and the substrate. Piezoelectric hysteresis loops are obtained in the remanent piezoelectric response regime     

Photo and thermally induced properties change in Bi/Ag/Se trilayer thin film

In this article, we have demonstrated the optical and structural properties change in Bi/Ag/Se trilayer thin films by the influence of thermal and photon energy. The trilayer films prepared by thermal evaporation technique were annealed and laser irradiated at room temperature. The X-ray diffraction study revealed the Ag₂Se phase formation and the surface morphology change is being studied by Field emission scanning electron microscopy. The optical properties of the studied films were characterized by using FTIR spectrophotometer in the wavelength range 400–1200?nm. The reduction of optical band gap by both thermal and laser irradiation is being discussed on the basis of chemical disorderness, defect states and density of localized states in the mobility gap. The Raman shift due to annealing and irradiation supports the changes in the film. The large change in optical band gap in thermal annealing is useful for memory device and waveguide fabrication.     

Co:BaTiO3/Si(100)纳米复合薄膜制备、微结构及其紫外光电子能谱研究

采用脉冲激光气相沉积(PLD)方法,在Si(100)晶面上制备了Co:BaTiO₃纳米复合薄膜.采用X射线衍射(XRD)结合透射电镜(TEM)方法研究了两种厚度Co:BaTiO₃纳米复合薄膜的晶体结构,当薄膜厚度约为30 nm时,薄膜为单一择优取向;当薄膜厚度约为100nm时,薄膜呈多晶结构.原子力显微镜(AFM)分析表明,当膜厚为30nm时,薄膜呈现明显的方形晶粒.采用紫外光电子能谱(UPS)研究了Co的价态和Co:BaTiO₃纳米复合薄 关键词： 3')" href="#">BaTiO₃ 纳米复合薄膜 紫外光电子能谱