重频激光对多壁碳纳米管悬浮液光限幅特性的影响研究

在激光以不同重复频率入射下,研究了直径分布为10～20 nm的多壁碳纳米管悬浮液对波长为1064 nm激光的光限幅效应,定性分析了不同重复频率激光对多壁碳纳米管悬浮液的光限幅影响。结果表明:碳纳米管悬浮液对波长为532 nm和1064 nm的激光都具有很强的光限幅响应;在多脉冲激光入射时,碳纳米管悬浮液的光限幅效应比单脉冲激光入射时更显著。     

多脉冲激光对碳纳米管悬浮液光限幅特性影响

利用实验的方法研究了碳纳米管悬浮液对脉宽8 ns,波长532 nm多脉冲激光的光限幅效应.分析了直径分布为10~20 nm的多壁碳纳米管悬浮液对重复频率分别为1 Hz、 3 Hz、 5 Hz、 10 Hz情况下532 nm激光的光限幅效应,分析计算了不同重复频率下碳纳米管悬浮液的限幅阈值,比较了不同焦距的透镜会聚入射光束情况下对碳纳米管悬浮液光限幅效果的影响.实验结果表明：碳纳米管悬浮液对不同重复频率的532 nm 激光都具有较强的光限幅特性;碳纳米管悬浮液对激光在不同重复频率入射情况下的光限幅阈值变化很大,当入射激光的重复频率为5 Hz时,碳纳米管悬浮液的光限幅阈值比单脉冲激光入射时的限幅阈值低了2倍,重复频率为10 Hz时的限幅阈值比单脉冲时的限幅阈值低了近3倍;碳纳米管在紧焦系统中的光限幅效果更好.     

可溶性碳纳米管Z扫描实验研究

以可溶性碳纳米管为研究对象，进行了Z扫描实验.实验中通过改变样品的参量，研究了材料在不同浓度和不同厚度下的Z扫描曲线特性；实验分别在532nm和1064nm的激光下进行，并分别进行了开孔和闭孔实验.材料的闭孔Z扫描曲线没有明显的峰谷对称结构，而开孔Z扫描曲线呈现关于原点对称的单一谷形状，表明样品存在较强的非线性吸收效应，非线性吸收可能是其主要的光限幅机理.     

可溶性碳纳米管Z扫描实验研究

以可溶性碳纳米管为研究对象,进行了Z扫描实验.实验中通过改变样品的参量,研究了材料在不同浓度和不同厚度下的Z扫描曲线特性;实验分别在532nm和1064nm的激光下进行,并分别进行了开孔和闭孔实验.材料的闭孔 Z扫描曲线没有明显的峰谷对称结构,而开孔Z扫描曲线呈现关于原点对称的单一谷形状,表明样品存在较强的非线性吸收效应,非线性吸收可能是其主要的光限幅机理.     

甲基红掺杂碳纳米管悬浮液的光限幅特性研究

利用实验的方法研究了甲基红掺杂碳纳米管悬浮液对波长为532 nm激光的光限幅效应.分析了样品厚度和入射激光重复频率对光限幅特性的影响,并与纯碳纳米管悬浮液的光限幅特性进行了比较.实验结果表明,对于线性透过率为60%（500 nm）的碳纳米管悬浮液,掺入甲基红后其沉淀速度明显减慢,限幅阈值由250 μJ降低为200 μJ;对于2和5 mm 厚度的样品,掺杂甲基红使碳纳米管悬浮液的箝位输出激光脉冲能量分别由45和20 μJ降低为35和9 μJ. 关键词： 非线性光学 光限幅效应 甲基红 染料掺杂碳纳米管悬浮液     

甲基红掺杂碳纳米管悬浮液的光限幅特性研究

利用实验的方法研究了甲基红掺杂碳纳米管悬浮液对波长为532 nm激光的光限幅效应.分析了样品厚度和入射激光重复频率对光限幅特性的影响,并与纯碳纳米管悬浮液的光限幅特性进行了比较.实验结果表明,对于线性透过率为60%（500 nm）的碳纳米管悬浮液,掺入甲基红后其沉淀速度明显减慢,限幅阈值由250 μJ降低为200 μJ;对于2和5 mm 厚度的样品,掺杂甲基红使碳纳米管悬浮液的箝位输出激光脉冲能量分别由45和20 μJ降低为35和9 μJ.     

碳纳米管悬浮液对532nm激光限幅机理的实验研究

通过光限幅、Z扫描、非线性吸收和散射能量分布实验,研究了碳纳米管悬浮液对532 nm激光的限幅机理以及样品厚度对光限幅机理的影响。结果表明:碳纳米管悬浮液的光限幅机理并非单纯的非线性散射,对低能量入射激光光限幅特性主要源于对入射激光的非线性吸收;对高能量入射激光,碳纳米管的吸收效应和它电离形成的微等离子体以及液体汽化所形成气泡散射效应的共同作用,使其具有较强的光限幅能力,对浓度一定的悬浮液,增加样品厚度虽然会增强其限幅效果,但却会减弱其非线性散射效应。     

聚对苯撑乙烯衍生物/氯仿溶液的自衍射及光限幅特性的研究

用532 nm基模高斯光束对2-甲氧基5-丁氧基取代聚对苯撑乙烯的氯仿溶液进行激光诱导衍射实验及光限幅特性的研究.实验发现,当高斯光束通过样品溶液时,在远场处出现衍射环;随着入射功率的增大,衍射图案会发生显著的变化.理论分析表明,该现象可以用光克尔效应、热效应作用下的附加相位孔对入射光束的衍射行为来解释.还进一步研究了532 nm激光作用下样品溶液的光限幅特性,根据实验结果分析得出:由热效应引起的自衍射是产生光限幅特性的主要机制.     

可溶性多壁碳纳米管光限幅机理研究

根据光限幅与Z扫描实验研究了可溶性多壁碳纳米管的光限幅机理.通过现象分析、数据处理以及类比研究,证实材料的光限幅特征符合非线性吸收效应.对厚样品的独特现象进行了解释,讨论了其他机理的影响.根据Z扫描公式,计算了实验材料的三阶非线性系数.通过分析证实了非线性吸收在可溶性多壁碳纳米管的光限幅中发挥着主要作用.对厚介质的特殊现象进行的分析和计算表明,对于较厚介质和激光连续加热的情况下,其他机理的影响并不能完全否定,其特殊现象可能与微气泡的气穴作用有关.     

多壁碳纳米管光限幅特性的研究

用化学气相沉积法制备了多壁碳纳米管,并将其溶解在甲苯溶液中.用波长为1064nm的皮秒脉冲激光测量该样品的透过率,发现了非常明显的光限幅特性.当入射光强较小时,透射光强度随入射光强度的增大而增大,输出与输入为线性关系;随着入射光强的增大,透射光强增长的速度明显变慢,并逐渐趋于饱和.当入射光强度较小时,样品的透过率接近100%;而当入射光强为8GW/cm²时,非线性透过率达到30%.根据三光子吸收理论计算,理论拟合与实验结果非常符合,说明多壁碳纳米管的三光子吸收产生了光限幅效应.实验测 关键词： 多壁碳纳米管 光限幅 三光子吸收     

Experimental Study on Optical Limiting and Transient All-optical Switching Properties of a Cubanelike Transition-metal Cluster Compound (n-Bu4N)3[MoAg3BrI3S4]

１ＩｎｔｒｏｄｕｃｔｉｏｎＩｎｒｅｃｅｎｔｙｅａｒｓ,ｔｈｅｐｏｔｅｎｔｉａｌｏｆｒｅｖｅｒｓｅｓａｔｕｒａｂｌｅａｂｓｏｒｐｔｉｏｎ（ＲＳＡ）ｍａｔｅｒｉａｌｓｉｎｏｐｔｉｃａｌｌｉｍｉｔｉｎｇａｎｄｏｐｔｉｃａｌｓｗｉｔｃｈｉｎｇｈａｖｅｇｒａｄ...     

Pulse duration and wavelength effects on the optical limiting behavior of carbon nanotube suspensions

We investigate pulse duration and wavelength effects on the optical limiting behavior of single-wall carbon nanotubes suspended either in chloroform or in water. The principal optical limiting effect in carbon nanotube suspensions is nonlinear scattering that is due to heat transfer from particles to solvent, leading to solvent-bubble formation and to sublimation of carbon nanotubes. We report on nonlinear transmittance measurements for pulse durations ranging from 3 to 100 ns and for wavelengths from 430 to 1064 nm. The dependence of optical limiting behavior on pulse duration and wavelength is analyzed and discussed in terms of nonlinear mechanisms.     

Optical limiting behavior of nano-gold self-assembled multi-wall carbon nanotube

The opticallimiting behaviors of nano-gold self-assembled multi-wall carbon nanotube (MWNT) were experimentally investigated at 532 and 1064 nm, respectively. The comparison of the limiting performances between carbon nanotube suspension, C60 solution, and carbon black suspension (CBS) was performed.The results show that the optical limiting characteristic of nano-gold self-assembled MWNT is better than those of C60 and CBS. The mechanisms of the optical limiting for the samples were discussed.     

A compact and high efficiency diode pumped green laser based on MgO doped PPLN

In this work, an efficient intra-cavity second harmonic generation of green laser in a periodically poled MgO doped LiNbO₃ (MgO:PPLN) bulk crystal using a compact Nd:YVO₄ laser as a fundamental laser source is reported. Different length, different working temperature MgO:PPLN crystals are tested and investigated in the SHG experiments. The maximum output power at 532 nm is 6.2 W at the absorbed pump power at 808 nm of 14 W, the optical to optical conversion efficiencies from 808 to 532 nm and 1064 to 532 nm are 43 and 77%, respectively, the instability in 2 hours is less than 5%.     

Laser removal of copper particles from silicon wafers using UV, visible and IR radiation

Laser removal of small copper particles from silicon wafer surfaces was carried out using Nd:YAG laser radiation from near-infrared (1064 nm) through visible (532 nm) to ultraviolet (266 nm). It has been found that both 266 nm and 532 nm are successful in removing the particles from the surface whereas 1064 nm was shown to be ineffective in the removal of particles. The damage-threshold laser fluence at 266 nm was much higher than other wavelengths which provides a much wider regime for safe cleaning of the surface without causing any substrate damage. The cleaning efficiency was increased with a shorter wavelength. The effect of laser wavelength in the removal process is discussed by considering the adhesion force of the particle on the surface and the laser-induced cleaning forces for the three wavelengths. Received: 31 May 2000 / Accepted: 14 July 2000 / Published online: 20 June 2001     

Enhanced optical limiting effect in fluorine-functionalized graphene oxide

Nonlinear optical absorption of fluorine-functionalized graphene oxide (F-GO) solution was researched by the open-aperture Z-scan method using 1064 and 532 nm lasers as the excitation sources. The F-GO dispersion exhibited strong optical limiting property and the fitted results demonstrated that the optical limiting behavior was the result of a two-photon absorption process. For F-GO nanosheets, the two-photon absorption coefficients at 1064 nm excitation are 20% larger than the values at 532 nm excitation and four times larger than that of pure GO nanosheets. It indicates that the doping of fluorine can effectively improve the nonlinear optical property of GO especially in infrared waveband, and fluorine-functionalized graphene oxide is an excellent nonlinear absorption material in infrared waveband.     

Nonlinear optical parameters and optical limitation in cobalt-doped polyvinylpyrrolidone solutions

Nonlinear optical parameters (nonlinear refractive indices and nonlinear absorption coefficients) of solutions of polyvinylpyrrolidone doped by cobalt to various concentrations are measured at the lasing and second-harmonic wavelengths of a picosecond Nd:YAG laser (λ=1064 and 532 nm, respectively, and τ=35 ps). Data on optical limitation in these solutions are presented. The absence of nonlinear absorption in the IR spectral range and its significant effect in the visible range are demonstrated. Optical limitation at a wavelength of 1064 nm is related to defocusing, whereas at 532 nm, this effect is caused by two-photon absorption and partially by inverse saturated absorption and defocusing. Nonlinear optical parameters of metal-polymer complexes are reported.