彩色有机薄膜电致发光及动态矩阵显示

研究了绿色、红色、蓝色和白色4种有机薄膜电致发光器件.通过掺杂得到了高稳定性的绿色及红色器件,绿色器件的半寿命达14000小时(初始亮度100cd/m²),红色器件的半寿命为7500小时(初始亮度50cd/m²).还研究了具有空穴锁定层及非锁定层的多种不同结构和材料的蓝色及白色器件.研究表明无论蓝色还是白色器件,具有空穴锁定层的器件稳定性较差,老化过程中界面势垒的变化很大.非锁定层的蓝色及白色器件中,新材料JBEM比DPVBi有更优越的性能.JBEM构成的蓝色器件的半亮度寿命为1035小时(初始亮度100cd/m²).由JBEM构成的白色器件中,由蓝色及红色掺杂在同一层的器件得到最好的稳定性,其半亮度寿命为2800小时(初始亮度100cd/m²),而且它具有发光颜色不随电流变化而变化的特点.在稳定性改善的基础上研制成功96×60线,分辨率为2线/mm的绿色及白色矩阵显示屏,还利用选择蒸发的方法制造了彩色矩阵屏,设计和研制了驱动及控制电路,实现了动态显示.     

稳定的蓝色及白色有机薄膜电致发光器件

报道了一种稳定的蓝色和白色有机薄膜电致发光器件,蓝色器件最大亮度为7526cd／m^2,最大效率1．451m／W,半亮度寿命1035h(初始亮度l00cd／m^2)。白色器件的最大亮度为14850cd／m^2,最大效率2．881m／W,色度x=0．31,y=0．38,且色度不随电流增大而变化,半亮度寿命为2860h(初始亮度100cd／m^2)。     

稳定的光谱不随电流变化而改变的白色有机发光器件

使用新材料构成了两种结构白色有机薄膜电致发光器件，一种是蓝色及红色发射在同一层中，另一种是蓝色发射和红色发射分别在两层中，器件结构分别为ITO／CuPc／NPB／JBEM（P）：DCJT／Alq／MgAg（器件1）和ITO／CuPc／NPB／JBEM（P）／Alq：DCJT／Alq／MgAg（器件2）。这里（CuPc）是空穴注入层；N，N’－bis－（1－naphthyl）－N，N’－diphenyl－1，1’bipheny1－4－4’－diamine（NPB）是空穴传输层（HTL）；9，10－bis（3’5’－diaryl）phenyl anthracene（JBEM）是蓝色发射层；tris（8－quinolinolato）aluminium complex（Alq）是电子传输层（ETL）；DCJT是红色染料。在器件1中得到稳定的且色度不随电流增在而变化的白色发射。它的最大亮度为14850cd/m^2，最大效率2．88lm/W，色度x＝0．31，y＝0．38（从4mA/cm^2到200mA/cm^2），半亮度寿命为2860小时（初始亮度1000cd/m^2）。比较了两种结构的器件，蓝红色发射在同一层结构的器件，在亮度、效率及稳定性上都优于蓝红发射在不同层结构的器件。     

发光效率及稳定性改善的有机薄膜电致发光器件

不久前,我们报导了以TPD为空穴传输层,Alq为电子传输兼发光层的双层薄膜电致发光器件,在定电流密度6mA/cm2连续驱动下,初始亮度106cd/m2下降至一半亮度的时间为120小时,而继续操作500小时,亮度仍有38cd/m2[1]。在这篇文章中,我们将报道一个在上述器件的空穴传输层TPD中掺杂而构成的新器件。这个新器件发光亮度和效率比原器件增加了50%,而稳定性增加了近10倍,初始亮度165cd/m2的半亮度寿命达1200小时。     

白色有机发光器件及其稳定性

报道了一种稳定的白色有机薄膜电致发光器件.电流效率6cd/A,在电流密度20mA/cm²驱动下,亮度为1026cd/m²;最高亮度21200cd/m²,色度(x=0.32,y=0.40).该器件具有较平稳的效率电流关系,即具有弱的电流荧光猝灭.初始亮度100cd/m²下,半亮度寿命达22245h.     

空穴传输层掺杂SrF2的高效率蓝色磷光OLED器件

通过在OLED器件的空穴传输层中掺杂不同比例的SrF2制作出了高效率蓝色磷光OLED器件.这种器件能有效提高蓝色磷光OLED器件的空穴注入与传输特性,降低器件的的工作电压,提高流明效率(19.11m/W)、电流效率(26.9 cd/A)以及亮度(22 220 cd/m2),和未经掺杂的参比器件相比,分别提高了85.4％...     

高亮度高效率蓝色聚合物发光二极管

蓝色聚合物发光二极管是人们关注的课题,前不久,我们报道[1]了利用ITO/PVCz/BBOT/Mg·Ag结构达到亮度1700cd/m2,量子效率0.2%的蓝色器件.在本文中我们报道以掺杂perylene(PRL)和triphenylamine(TPA)的poly(N-vinylcar-bazole)(PVCz)为空穴传输层,以PBD为空穴锁住层,Alq为电子注入层的器件,其亮度达6100cd/m2,量子效率达0.7500,流明效率0.451m/W的蓝色发光器件.就我们所知,这个亮度是蓝光中最高的亮度.     

利用缓变结提高蓝色有机发光二极管的寿命

在空穴传输层(HTL)和发光层(EML)界面加入缓变结的蓝色有机电致发光器件(Cell-GJ)。与传统的异质结结构的有机电致发光器件(Cell-HJ)相比,寿命有了明显的提高:半寿命在初始亮度为100 cd/m2的条件下达到了8460 h,比Cell-HJ的半寿命长6倍。寿命的延长归功于穿过非突变界面的局部电场的消除,减少了焦耳热的产生从而提高了器件的寿命。但是实验证实Cell-GJ的效率比Cell-HJ的效率低。为了提高Cell-GJ的效率在其TBADN/AlQ交界处蒸镀GaQ薄层制得一种新型器件Cell-GJGaQ。由于GaQ的最低未占有轨道能级介于AlQ和TBADN之间,从AlQ到GaQ再到TBADN形成的多阶势垒可以极大地提高电子(少子)注入,从而使发光效率也有了明显改善。研究结果表明Cell-GJGaQ的效率比Cell-GJ的效率高20%,半寿命同时也达到了6998 h,比Cell-HJ长5倍,整体性能有了较大提高。     

间隔层对双发光层白色有机电致发光器件性能的影响

采用蓝色bis (FIrpic)和黄色bis iridium(acetylacetonate) 两种磷光染料,制备了双发光层结构的白色有机电致发光器件,器件结构为ITO/TAPC (30 nm)/host: (t-bt)₂Ir(acac) /spacer (x nm)/host: FIrpic (15 nm, 8%)/Bphen (40 nm)/Mg∶Ag (200 nm)。分别选用p型1,1-bis cyclohexane (TAPC)和n型tris borane (3TPYMB)作为主体材料制备了两种类型的器件,通过在两个发光层之间加入一层较薄的间隔层进行器件优化。结果表明,加入间隔层之后,器件性能得到提高,获得了色稳定性较好的白光器件。当主体为TAPC时,使用间隔层后器件取得最大亮度为19 550 cd/m²,最大电流效率为8.3 cd/A;当主体为3TPYMB时,使用间隔层后器件的最大亮度为1 950 cd/m²,最大电流效率为30.7 cd/A。实验结果表明,器件性能的提高,是由于加入了间隔层之后载流子复合区域拓宽,促进了发光层中电子和空穴的平衡。     

两种蓝色有机电致发光材料

重点研究以两种蓝色OEL材料蒽类衍生物JBEM和联苯乙烯衍生物DPVBi分别作基质，以perylene作掺杂剂的器件的电致发光性能，特别研究了它稳定性，在这度和效率方面，两种器件并没有很大差别，然而在稳定性方面却有很大差别，蒽类衍生物JBEM的器件在100cd/m^2初始亮度下，半亮度寿命可达1035h，而DPVBi的器件在同样条件下，半亮度寿命为255h。通过分析两种器件的能级图，认为稳定性的差别可能源于两种蓝光材料本身的热稳定性不同，JBEM优于DPVBi，是一种很有前途的蓝色发光材料。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.