单极型马赫-曾德尔调制器的互调失真分析

针对单极型马赫曾德尔电光调制器在Radio over Fiber(RoF)和副载波复用系统中的应用,讨论了输入两路射频信号的情形,给出了电光调制器互调失真的严格通用解析解。该解析解可用于表示任意阶的互调失真项和谐波项。数值结果表明了该解析解的正确性。分析结果表明,调制器的三阶互调失真与调制器偏置相移无关,只与输入射频信号的调制系数有关,并且当外加偏置电压等于调制器的半波电压时,只存在偶数阶的失真项。根据该解析解,可方便地设计模拟光通信系统,精确地预计外调制器的非线性特征,优化系统性能。     

采用mQAM和孔径平均的水下弱湍流MIMO系统性能分析

采用Log-normal分布模拟海洋弱湍流信道,接收机采用等增益合并方式,在考虑雪崩光电二极管(APD)散粒噪声、信道衰减、几何损耗、Log-normal湍流和孔径平均因子等链路条件下,从理论上推导了水下无线光通信多输入多输出系统平均误码率和信道平均容量的上界表达式,并定量分析讨论了不同链路参数对系统平均误码率和信道平均容量的影响.数值结果表明,采用调制指数合适的正交幅度调制方式以及较大的天线数、接收孔径、发射光功率,均有助于提升系统性能.     

Gamma-Gamma湍流信道中大气光通信系统误码特性分析

大气信道中的大气湍流是影响无线激光通信系统性能的主要因素之一, 其引起的强度闪烁效应会对接收信号的提取和还原造成很大干扰。基于Gamma-Gamma概率分布的大气湍流信道统计模型, 研究了利用副载波相移键控(PSK)强度调制技术的大气光通信系统的误码特性; 推导了副载波二进制相移键控(BPSK)及开关键控(OOK)两种调制模式下的系统误码率表达式; 对在一定条件下的大气光通信系统, 比较了副载波BPSK和OOK两种调制模式的误码特性; 分析了链路特征、接收口径尺寸、通信波长和天顶角等因素对系统误码率的影响。结果表明, 增大接收孔径和通信波长都能有效地降低系统误码率, 而天顶角的增大则会使系统误码率增加, 副载波BPSK调制模式的误码特性要优于OOK调制模式的误码特性。     

基于Volterra滤波器的参量阵扬声器互调失真补偿研究

针对单边带调制方法预处理的参量阵扬声器系统在复杂信号输入情况下存在明显互调失真的问题,引入Volterra滤波器模型和简化的一维Volterra滤波器模拟了其互调失真。设计了相应的逆滤波器,并对其抑制系统互调失真的性能进行了实验对比。结果表明,所设计的逆滤波器都能有效降低系统的互调失真,而后者具有较低的计算复杂度。     

大气湍流对轨道角动量态复用系统通信性能的影响

通过数值仿真,以多个相位屏模拟大气湍流,研究大气湍流对轨道角动量(Orbital Angular Momentum,OAM)态复用通信系统质量的影响.改变大气湍流折射率结构常量C2n和传输距离z,分析其对OAM态复用系统归一化接收功率、误码率等的作用.研究结果表明当大气湍流强度增加和传输距离增长时,复用系统归一化接收功率下降、误码率增加.当C2n增大到5×10-13 m-2/3时,系统归一化接收功率下降到0.2以下,误码率增大到0.3以上;当传输距离增大到10 000m,系统归一化接收功率下降到0.3以下,误码率增大到0.35以上.同时,对比不同方位角指数l取值的两个OAM态复用系统受大气湍流的影响,发现:l取值越接近的系统,受大气湍流影响越大.在等同光学信噪比下大气湍流导致OAM态复用系统误码率性能降低2至3个数量级.该研究对OAM态复用系统的实用化具有积极的参考作用.     

降低可见光通信不均匀限幅正交频分复用系统非线性限幅失真的功率分配方法

针对可见光通信中不均匀限幅光正交频分复用(ACO-OFDM)系统发光二极管(LED)非线性限幅失真严重的问题,提出了一种降低LED非线性限幅失真的最优功率分配方法。基于原信号直接叠加非线性限幅失真成分的限幅处理模型,分析了ACO-OFDM系统中的LED非线性限幅失真;利用有效信噪比来衡量限幅失真,将限幅失真转化为有效信噪比分析;基于有效信噪比最优的原则给出了光功率约束下降低限幅失真的最优偏置信号和ACO-OFDM信号功率分配。仿真结果表明,当信道的信噪比较低时,信道噪声起主导作用;当信道的信噪比较高时,限幅失真起主导作用。在光功率约束下若不考虑偏置信号的影响而直接取其值为LED最小输出功率限制,则系统误码率(BER)在信道信噪比大于40dB的情况下也始终大于10-2,而采用最优功率分配时可以保证系统具有较好的误码率性能,当光功率约束为200mW和250mW时,分别需要24dB和27dB的信道信噪比即可使得系统的误码率低于10-3。     

部分相干光通过强湍流对通信系统误码率的影响

为研究部分相干光通过强湍流对系统误码率的影响,借助对激光在大气湍流场中的传输方程进行解析求解(忽略系统中其他噪声,仅考虑由大气湍流引起的系统误码率),得到不同湍流内尺度、传输激光波长和光源相干参数条件下,系统误码率和传输距离的关系.结果表明:在强湍流条件下,当发射天线数目达到一定时,随着传输距离的增加,系统误码率逐渐增大,但增大到一定程度后趋于饱和;光源相干参数越大,系统误码率越低;湍流内尺度越大,系统误码率越高;传输激光波长的变化对系统误码率无明显影响.     

一种提高强度调制直接检测基带光双边带正交频分复用系统传输性能的预处理技术

为了减轻电光调制器的非线性效应以及光纤色度色散给直接检测光正交频分复用系统性能带来的损伤,对两者的损伤机理进行了理论分析.在此基础上提出了在发射中使用一种针对调制器的非线性采用预失真技术,而高频子载波功率衰减采用预增强的联合预处理技术来改善系统的性能.运用数值仿真法对所提出的方法进行了验证,结果表明在光背靠背传输系统中调制指数最优时,接收信号的误差矢量幅度值可以得到2dB的改善.随着光纤传输距离的增长,正交频分复用信号高频子载波功率衰减程度加剧而使得信噪比恶化,从而导致系统误码性能急剧下降.使用所提出的预处理技术的计算复杂程度低,可以使接收机的灵敏度得到明显的改善.     

微波光子信道化链路非线性失真的数字补偿方法

微波光子信道化链路的线性度主要受信道内的交调失真和信道间的互调失真的限制。本文提出了一种基于数字域迭代的非线性失真补偿方法，对各个信道输出的中频信号在数字域进行联合处理，通过迭代不断逼近线性化的理想结果，能够同时有效抑制信道化链路中的交调失真和互调失真。仿真结果表明，在参数无偏差的情况下，该方法可以完全抑制信道内的交调失真和信道间的互调失真；在参数偏差为5%的情况下，仍可以将三阶交调失真和互调失真分别抑制15 dB和16 dB。     

单载波频域均衡中的水声信道频域响应与噪声估计

本文对单载波频域均衡(SC-FDE)中的信道和噪声估计进行研究,理论分析了形成误码率平台的可能原因,提出了基于Chu序列的联合信道时频域响应和噪声功率估计算法.利用水声信道响应的稀疏特性和门限确定信道能量集中区域,进行信道估计的去噪处理和噪声功率计算.借助于水声射线模型对所提出的算法进行了仿真,分析了噪声估计对SC-FDE性能的重要影响.仿真结果表明,所提出的信道和噪声估计算法可以有效减缓或消除SC-FDE中的误码率平台.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.