Preparation and characterization of low density polystyrene/TiO2 core–shell particles for electronic paper application

In order to reduce the density mismatch between TiO₂ and the low dielectric medium and improve the dispersion stability of the electrophoretic particles in the low dielectric medium for electrophoretic display application, polystyrene/titanium dioxide (PS/TiO₂) core–shell particles were prepared via in-situ sol–gel method by depositing TiO₂ on the PS particle which was positively charged with 2-(methacryloyloxy)ehyl trimethylammonium chloride (DMC). The morphology and average particle size of PS/TiO₂ core–shell particles were observed by transmission electron microscopy (TEM), scanning electron microscope (SEM) and particle size analyzer. It was found that density of PS/TiO₂ core–shell particles were reduced obviously and the particles can suspend in the low dielectric medium of low density. The PS/TiO₂ core–shell particles can endure ultrasonic treatment because of the interaction between TiO₂ and PS. Zeta potential and electrophoretic mobility of the fabricated core–shell particles in a low dielectric medium with charge control agent was measured to be −44.3 mV and −6.07 × 10⁻⁶ cm²/Vs, respectively, which presents potential in electronic paper application.     

The effect of ultrasonic irradiation on the structure,morphology and photocatalytic performance of ZnO nanoparticles by sol-gel method

In this research, the effect of ultrasonic irradiation power (0, 75, 150 and 200 W) and time (0, 5, 15 and 20 min) on the structure, morphology and photocatalytic activity of zinc oxide nanoparticles synthesized by sol-gel method was investigated. Crystallographic structures and the morphologies of the resultant powders were determined by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The XRD patterns showed that ZnO samples were crystallized in their pure phase. The purity of samples was increased by increasing the ultrasonic irradiation power and time. Not only did ultrasonic irradiation unify both the structure and the morphology, but also it reduced the size and prohibited particles from aggregation. The optical behavior of the samples was studied by UV–vis spectroscopy. Photocatalytic activity of particles was measured by degradation of methyl orange under radiation of ultraviolet light. Ultrasound nanoparticles represented higher degradation compared to non-ultrasound ones.     

Sonochemical synthesis of silver nanorods by reduction of sliver nitrate in aqueous solution

The sonochemical synthesis of sliver nanorods has been achieved by ultrasonic irradiation of the aqueous solution of sliver nitrate, methenamine (HMTA) and poly (vinyl pyrrolidone) (PVP) for 60 min. The silver nanorods obtained have lengths of 4–7 μm and mean diameters of about 100 nm. The structures of the samples were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), selected area electron diffraction (SAED) and X-ray powder diffraction (XRD), and the chemical composition of the sample was examined by energy-dispersive X-ray spectrum (EDS). The effects of the irradiation time, the concentration of PVP and the reaction temperature on the morphology of silver nanorods were discussed, and the mechanism of the silver nanorods formation was tentatively inferred.     

In situ SEM,TEM and AFM studies of the antimicrobial activity of lemon grass oil in liquid and vapour phase against Candida albicans

Inhibition of Candida albicans growth was shown by lemon grass oil (LGO) and lemon grass oil vapour (LGO vapour) at 288 μg/ml and 32.7 μg/ml concentration, respectively. The assessment of cell damage by LGO and LGO vapour was done through scanning electron microscope (SEM), transmission electron microscope (TEM) and atomic force microscope (AFM) observations. SEM analysis showed complete rupture of C. albicans cells treated with LGO vapour while in those treated with LGO in broth, only shrinkage was observed. TEM study showed the alterations in morphology upon treatment with LGO while complete degradation of the Candida cells was observed in case of LGO vapour. Further three dimensional morphological changes and roughness of the cells have also been evaluated with AFM after the treatment with LGO & LGO vapour. Roughness (root mean square value) was significantly higher in control C. albicans cells (211.97 nm) than LGO (143 nm) and LGO vapour (5.981 nm) treated cells. The results for the first time demonstrate relatively higher efficacy of LGO vapours for inhibition and cellular damage of C. albicans cells as compared to the LGO in liquid phase. This suggests the potential application of LGO vapour phase against infections caused by C. albicans.     

Ultrasonic pretreatment of corn slurry for saccharification: A comparison of batch and continuous systems

The effects of ultrasound on corn slurry saccharification yield and particle size distribution was studied in both batch and continuous-flow ultrasonic systems operating at a frequency of 20 kHz. Ground corn slurry (28% w/v) was prepared and sonicated in batches at various amplitudes (192–320 μm_{peak-to-peak (p–p)}) for 20 or 40 s using a catenoidal horn. Continuous flow experiments were conducted by pumping corn slurry at various flow rates (10–28 l/min) through an ultrasonic reactor at constant amplitude of 12 μm_p–p. The reactor was equipped with a donut shaped horn. After ultrasonic treatment, commercial alpha- and gluco-amylases (STARGEN^TM 001) were added to the samples, and liquefaction and saccharification proceeded for 3 h. The sonicated samples were found to yield 2–3 times more reducing sugars than unsonicated controls. Although the continuous flow treatments released less reducing sugar compared to the batch systems, the continuous flow process was more energy efficient. The reduction of particle size due to sonication was approximately proportional to the dissipated ultrasonic energy regardless of the type of system used. Scanning electron microscopy (SEM) images were also used to observe the disruption of corn particles after sonication. Overall, the study suggests that both batch and continuous ultrasonication enhanced saccharification yields and reduced the particle size of corn slurry. However, due to the large volume involve in full scale processes, an ultrasonic continuous system is recommended.     

Properties of Bi2O3 thin films prepared via a modified Pechini route

Thin bismuth oxide films have been prepared by a modified Pechini route on glass substrate and annealed at temperatures ranging between 400 °C and 700 °C using bismuth nitrate as raw material. The thin films were then characterized for structural, surface morphological, optical and electrical properties by means of X-ray diffraction (XRD), Atomic force microscopy (AFM), scanning electron microscopy (SEM), optical absorption and d.c. two-probe, respectively. Structural investigations indicated that as-prepared bismuth oxide films were polycrystalline and multiphase, and annealing temperatures played a key role in the composition and optical properties of these films. AFM and SEM images revealed well defined particles which are highly influenced by annealing temperatures. The optical studies showed a direct band gap which varied with annealing temperatures between 3.63 eV and 3.74 eV. The electrical measurement showed that the electrical resistivity increased with annealing temperatures and the films were typical semiconductors. As catalyst, bismuth oxide films annealed at 550 °C had the best photocatalytic performance for photodegradation of methyl orange.     

One-step simple sonochemical fabrication and photocatalytic properties of Cu2O–rGO composites

An easy, one-step synthesis of Cu₂O–reduced graphene composites (Cu₂O–rGO) was developed using a simple sonochemical route without any surfactants or templates. The morphology and structure of the Cu₂O–rGO composites were characterised using techniques such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). The results indicated that the Cu₂O sphere is approximately 200 nm in diameter and composed of small Cu₂O particles approximately 20 nm in diameter. The morphology and composition of the Cu₂O–rGO composites could be well controlled by simply changing the mole ratio of the reactants under ultrasonic irradiation. The Cu₂O–rGO composites displayed better photocatalytic performance for the degradation of methyl orange (MO) than pure Cu₂O spheres, which may have potential applications in water treatment, sensors, and energy storage.     

Ultrasonic assisted synthesis,characterization and influence factors of monodispersed dumbbell-like YF3 nanostructures

In the present paper, we reported the successful synthesis of dumbbell-like YF₃ nanostructures with a high yield in a mixed system of water/N,N-dimethylformamide (DMF) under the assistance of ultrasound waves of 40 kHz with the ultrasonic power of 100% (200 W) at 65 °C for 2 h, employing Y₂O₃ (99.99%) and NH₄F as the starting reactants. The product was characterized by means of powder X-ray diffraction (XRD), energy dispersive spectrometry (EDS), transmission electron microscopy (TEM), selected area electron diffraction (SAED) pattern and field-emission scanning electron microscopy (SEM). Some factors influencing the morphology of YF₃ nanostructures, including the ultrasonic time and power, the amount of NH₄F, and the ratio of water/DMF, were systematically investigated. Research showed that the morphology of YF₃ could be tuned by the volume ratio of water/DMF. The roles of DMF and the ultrasonic wave in the formation of YF₃ nanostructures were discussed.     

Characterization of NaTaO3 synthesized by ultrasonic method

NaTaO₃ perovskite-like materials were synthesized using sodium acetate and tantalum ethoxide as precursors in an ultrasonic bath at room temperature. The pristine sample was thermally treated at 600 °C and characterized using XRD, N₂ physisorption, DRS, SEM and TEM techniques. The structural characterization by X-ray powder diffraction revealed that the crystallization of the NaTaO₃ phase prepared at 600 °C showed agglomerates sizes in the micrometric scale, as confirmed by scanning electron microscopy (SEM). On the other hand, well-defined NaTaO₃ particles in the nanometric scale were determined using TEM. It was found that, for the treated sample, the band gap and BET area was 3.8 eV and 9.5 m² g^?1, respectively. The annealed perovskite, deposited onto ITO glass, presented an important variation in the open circuit potential transient during UV light irradiation in neutral solution, compared with its counterpart prepared by solid-state method. These intrinsic properties, given by the preparation route, might be appropriate for increase its photocatalytic activity.     

Effect of processing conditions on sonochemical synthesis of nanosized copper aluminate powders

Nanosized copper aluminate (CuAl₂O₄) spinel particles have been prepared by a precursor approach with the aid of ultrasound radiation. Mono-phasic copper aluminate with a crystallite diameter of 17 nm along the (3 1 1) plane was formed when the products were synthesized using Cu(NO₃)₂·6H₂O and Al(NO₃)₃·9H₂O as starting materials, with urea as a precipitation agent at a concentration of 9 M. The reaction was carried out under ultrasound irradiation at 80 °C for 4 h and a calcination temperature of 900 °C for 6 h. The synthesized copper aluminate particles and the effect of different processing conditions such as the copper source, precipitation agents, sonochemical reaction time, calcination temperature and time were analyzed and characterized by the techniques of powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM) and Fourier transformation infrared spectroscopy (FT–IR).     

Preparation of magnetic FeCo nanoparticles by coprecipitation route

Magnetic FeCo nanoparticles with high saturation magnetization (M_s = 148 emu/g) at 15 kOe were prepared by a coprecipitation route. The value of M_s for FeCo nanoparticles depends on the ratio of Fe to Co components. The size of the nanoparticles was confirmed by transmission electron microscopy (TEM) images, and morphology of the nanoparticles was obtained by field emission scanning electron microscopy (FE-SEM) images. The crystal structure of the nanoparticles dependent on annealing was characterized by X-ray diffraction data. The magnetic properties were characterized by saturation magnetization from a hysteresis loop by VSM.     

Unique sharp photoluminescence of size-controlled sonochemically synthesized zirconia nanoparticles

The present study explores the features of tetragonally stabilized polycrystalline zirconia nanophosphors prepared by a sonochemistry based synthesis from zirconium oxalate precursor complex. The sonochemically prepared pristine zirconia, 3 mol%, 5 mol% and 8 mol% yttrium doped zirconia nanophosphors were characterized using thermo-gravimetric analysis (TGA), X-ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FE-SEM) with energy dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS) and photoluminescence spectroscopy (PL). The reaction mechanism of formation of zirconia nanophosphors is discussed in detail. The probable sonochemical formation mechanism is being proposed. Stabilization of tetragonal phase of pristine zirconia even at room temperature was effectively established by controlling the particle size using ultrasonic waves. Improved phase purity and good surface morphology of the nanophosphors is being achieved via sonochemical route. FE-SEM micrographs reveal that the nanoparticles have uniform spherical shape and size. The narrow particle size distribution (∼15–25 nm) of the zirconia nanoparticles was found from FE-SEM statistical analysis and further confirmed by TEM. Zirconia nanophosphors exhibit a wide energy band gap and which was found to vary with yttrium dopant concentration. The highlight of the present study is the synthesis of novel nanocrystalline ZrO₂ and Y-ZrO₂ phosphor which simultaneously emits extremely sharp as well as intense UV, violet and cyan light on exciting the host atom. The yttrium ion dopant further enhances the photoluminescence property of zirconia. These nanocrystalline phosphors are likely to have remarkable optical applications as light emitting UV-LEDs, UV lasers and multi color displays.     

Deposition and optical properties of nanocrystalline ZnS thin films by a chemical method

Highly transparent and adherent nanocrystalline large-area ZnS thin films were grown on the slide glass and the SnO₂-coated glass substrate by chemical deposition using an aqueous solution containing zinc sulfate and thioacetamide. The films were characterized by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, UV–Vis transmission and photoluminescence. The SEM morphologies of the films revealed a string-like structure formed by the smaller particle on the ZnS film surface. The average particle size was confirmed, using XRD analysis and TEM observation, to be about 3–4 nm.     

The influence of structure depth on image blurring of micrometres-thick specimens in MeV transmission electron imaging

This study investigates the influence of structure depth on image blurring of micrometres-thick films by experiment and simulation with a conventional transmission electron microscope (TEM). First, ultra-high-voltage electron microscope (ultra-HVEM) images of nanometer gold particles embedded in thick epoxy-resin films were acquired in the experiment and compared with simulated images. Then, variations of image blurring of gold particles at different depths were evaluated by calculating the particle diameter. The results showed that with a decrease in depth, image blurring increased. This depth-related property was more apparent for thicker specimens. Fortunately, larger particle depth involves less image blurring, even for a 10-μm-thick epoxy-resin film. The quality dependence on depth of a 3D reconstruction of particle structures in thick specimens was revealed by electron tomography. The evolution of image blurring with structure depth is determined mainly by multiple elastic scattering effects. Thick specimens of heavier materials produced more blurring due to a larger lateral spread of electrons after scattering from the structure. Nevertheless, increasing electron energy to 2 MeV can reduce blurring and produce an acceptable image quality for thick specimens in the TEM.     

Synthesis and characterization of Ag/PVA nanorods by chemical reduction method

Silver (Ag) nanorods with the average length of 280 nm and diameters of around 25 nm were synthesized by a simple reduction process of silver nitrate in the presence of polyvinyl alcohol (PVA) and investigated by means of scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission-electron microscopy (TEM) and UV–vis spectrum. It was found out that both temperature and reaction time are the important factors in determining the morphology and aspect ratios of nanorods. TEM images showed the prepared Ag nanorods have a face centered shape (fcc) with fivefold symmetry consisting of multiply twinned face centered cubes as revealed in the cross-section observations. The fivefold axis, i.e. the growth direction, normally goes along the (1 1 1) zone axis direction of the basic fcc Ag-structure. Preferred crystallographic orientation along the (1 1 1), (2 0 0) or (2 2 0) crystallographic planes and the crystallite size of the Ag nanorods are briefly analyzed.     

Three dimensional accurate morphology measurements of polystyrene standard particles on silicon substrate by electron tomography

Polystyrene latex (PSL) nanoparticle (NP) sample is one of the most widely used standard materials. It is used for calibration of particle counters and particle size measurement tools. It has been reported that the measured NP sizes by various methods, such as Differential Mobility Analysis, dynamic light scattering (DLS), optical microscopy (OM), scanning electron microscopy (SEM) and atomic force microscopy (AFM), differ from each other. Deformation of PSL NPs on mica substrate has been reported in AFM measurements: the lateral width of PSL NPs is smaller than their vertical height. To provide a reliable calibration standard, the deformation must be measured by a method that can reliably visualize the entire three dimensional (3D) shape of the PSL NPs. Here we present a method for detailed measurement of PSL NP 3D shape by means of electron tomography in a transmission electron microscope. The observed shape of the PSL NPs with 100 nm and 50 nm diameter were not spherical, but squished in direction perpendicular to the support substrate by about 7.4% and 12.1%, respectively. The high difference in surface energy of the PSL NPs and that of substrate together with their low Young modulus appear to explain the squishing of the NPs without presence of water film.     

Ultrasound with low intensity assisted the synthesis of nanocrystalline TiO2 without calcination

A novel method has been developed for the preparation of nano-sized TiO₂ with anatase phase. Nanoparticles with diameter about 6 nm were prepared at a relatively low temperature (75 °C) and short time. The synthesis was carried out by the hydrolysis of titanium tetra-isopropoxide (TTIP) in the presence of water, ethanol, and dispersant under ultrasonic irradiation (500 kHz) at low intensity. The results show that variables such as water/ethanol ratio, irradiation time, and temperature have a great influence on the particle size and crystalline phases of TiO₂ nanoparticles. Characterization of the product was carried out by different techniques such as powder X-ray diffraction (XRD), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM) and UV–vis spectroscopy.     

Nanocomposite Ni–TiN coatings prepared by ultrasonic electrodeposition

Nanocomposite Ni–TiN coatings were prepared by ultrasonic electrodeposition and the effects of ultrasonication on the coatings were studied. X-ray diffraction analysis was utilized to detect the crystalline and amorphous characteristics of the composite coatings. The surface morphology and metallurgical structure were observed by scanning electron microscopy, high-resolution transmission electron microscopy and scanning probe microscopy. The results showed that ultrasonication had great effects on TiN nanoparticles in composite coatings. The moderate ultrasonication conduced to homogeneous dispersion of TiN particles in the coatings. Moreover, the TiN nanoparticles that entered and homogeneously dispersed in the composite coating led to an increase in the number of nuclei for nucleation of nickel grains and inhibition of grain growth. Therefore, the introduction of ultrasonication and TiN nanoparticles resulted in the formation of smaller nickel grains. The average grain diameter of TiN particles was ∼33 nm, while Ni grains measured approximately 53 nm.     

Synthesis and characterization of monodisperse copper nanoparticles using gum acacia

A simple method was put forward in this paper for preparing colloidal copper nanoparticles in aqueous solutions using copper sulfate, gum acacia and hydrazine hydrate as copper precursor, capping agents and reducing agents, respectively, without any inert gas. The formation of nanosized copper was confirmed by its characteristic surface plasmon absorption peak at 604 nm in UV–vis spectra. The transmission electron microscopic (TEM) and scanning electron microscope (SEM) images show that the as-synthesized copper fine spherical particles are distributed uniformly with a narrow distribution from 3 nm to 9 nm. The X-ray diffraction (XRD) and high resolution transmission electron microscopic (HRTEM) demonstrated that the obtained metallic nanoparticles are single crystalline copper nanoparticles. Fourier transform infra-red (FT-IR) spectroscopic data suggested that the copper nanoparticles are coated with gum acacia. The effects of the quantity of gum acacia on the particle size were investigated by the UV–vis spectra and TEM images. The growth process of the nanoparticles was monitored by the UV–vis spectra. The mechanism of the formation copper nanoparticles was discussed. The process raised in this study can be served as an excellent candidate for the preparation of copper nanoparticles in a large scale production.     

Sonochemical effect on size reduction of CaCO3 nanoparticles derived from waste eggshells

A novel combination of mechanochemical and sonochemical techniques was developed to produce high-surface-area, bio-based calcium carbonate (CaCO₃) nanoparticles from eggshells. Size reduction of eggshell achieved via mechanochemical and followed by sonochemical method. First, eggshells were cleaned and ground, then ball milled in wet condition using polypropylene glycol for ten hours to produce fine particles. The ball milled eggshell particles were then irradiated with a high intensity ultrasonic horn (Ti-horn, 20 kHz, and 100 W/cm²) in the presence of N,N-dimethylformamide (DMF); decahydronaphthalene (Decalin); or tetrahydrofuran (THF). The ultrasonic irradiation times varied from 1 to 5 h. Transmission electron microscopic (TEM) studies showed that the resultant particle shapes and sizes were different from each solvent. The sonochemical effect of DMF is more pronounced and the particles were irregular platelets of ～10 nm. The BET surface area (43.687 m²/g) of these nanoparticles is much higher than that of other nanoparticles derived from eggshells.