Investigation of process variables and intensification effects of ultrasound applied in oxidative desulfurization of model diesel over MoO3/Al2O3 catalyst

A new heterogeneous sonocatalytic system consisting of a MoO₃/Al₂O₃ catalyst and H₂O₂ combined with ultrasonication was studied to improve and accelerate the oxidation of model sulfur compounds of diesel, resulting in a significant enhancement in the process efficiency. The influence of ultrasound on properties, activity and stability of the catalyst was studied in detail by means of GC-FID, PSD, SEM and BET techniques. Above 98% conversion of DBT in model diesel containing 1000 μg/g sulfur was obtained by new ultrasound-assisted desulfurization at H₂O₂/sulfur molar ratio of 3, temperature of 318 K and catalyst dosage of 30 g/L after 30 min reaction, contrary to the 55% conversion obtained during the silent process. This improvement was considerably affected by operation parameters and catalyst properties. The effects of main process variables were investigated using response surface methodology in silent process compared to ultrasonication. Ultrasound provided a good dispersion of catalyst and oxidant by breakage of hydrogen bonding and deagglomeration of them in the oil phase. Deposition of impurities on the catalyst surface caused a quick deactivation in silent experiments resulting only 5% of DBT oxidation after 6 cycles of silent reaction by recycled catalyst. Above 95% of DBT was oxidized after 6 ultrasound-assisted cycles showing a great improvement in stability by cleaning the surface during ultrasonication. A considerable particle size reduction was also observed after 3 h sonication that could provide more dispersion of catalyst in model fuel.     

Ultrasound-assisted mineralization of organic contaminants using a recyclable LaFeO3 and Fe3+/persulfate Fenton-like system

A recyclable heterogeneous catalyst has been successfully developed for application in a Fenton-type advanced oxidation process without adding external H₂O₂. LaFeO₃ was prepared from Fe(NO₃)₃·9H₂O and La(NO₃)·6H₂O by a simple sol-gel method and its catalytic efficiency was evaluated for mineralization of 4-chlorophenol using a Fenton-like process. The mineralization process was carried out under ultrasonication in presence of heterogeneous LaFeO₃ catalyst with H₂O₂ that was produced during ultrasonication. The mineralization process was monitored through total organic carbon (TOC) analysis. Very importantly, utmost 5-fold synergism was evidenced by the ultrasound mediated LaFeO₃-catalyzed system. Besides, more than twofold synergism was observed by combining the ultrasound assisted LaFeO₃ catalytic process and potassium persulfate (KPS) assisted advanced oxidation process. It is worth to mention that complete mineralization (∼96%) of 4-chlorophenol (initial concentration of 1.25 × 10⁻⁴ M) was observed within 1 h in the presence of LaFeO₃ (0.5 g L⁻¹) and KPS (1.0 mmol) under ultrasonication (40 kHz). Even after four cycles, the activity of LaFeO₃ remained intact which proved its recyclability. Extremely reusable heterogeneous LaFeO₃ catalyst makes the system more interesting from both economic and environmental points of view.     

Ultrasonic-assisted transesterification of Jatropha curcus oil using solid catalyst,Na/SiO2

The production of biodiesel from non-edible vegetable oil using ultrasonication, calls for an efficient solid catalyst to make the process fully ecologically and economically friendly. The methodology allows for the reaction to be run under atmospheric conditions. Solid catalyst and ultrasonication reduced the reaction time comparing to the conventional batch processes and we found 98.53% biodiesel yield. The optimal conditions for biodiesel production is the molar ratio oil to methanol 1:9, Catalyst conc. 3 wt.% of oil and 15 min reaction time.     

Thermoluminescence studies of thermally treated CaB4O7:Dy

Borate based thermoluminescence dosimeters (TLD) show high sensitivity and good TL characteristics. One of the promising material amongst the dosimeters is Dy doped CaB₄O₇. Spectrally resolved thermoluminescence of Dy doped CaB₄O₇ shows three glow peaks at about 50 °C, 240 °C and 380 °C, the intensity of the 240 °C glow peak being the maximum. All TL experiments were conducted on a high sensitivity TL spectrometer at Sussex University with a heating rate of 50 °C min^?1. Two main emissions associated with the Dy dopant are observed at ～480 and 580 nm. The samples were subjected to a series of treatments including excitation by X-rays and UV laser radiation. As part of the present research CaB₄O₇:Dy materials were subjected to two different heat treatments; quenching and slow cooling in order to investigate the changes in TL characteristics.     

Sonocatalytic and sonophotocatalytic degradation of rhodamine 6G containing wastewaters

The present work deals with degradation of aqueous solution of Rhodamine 6G (Rh 6G) using sonocatalytic and sonophotocatalytic treatment schemes based on the use of cupric oxide (CuO) and titanium dioxide (TiO₂) as the solid catalysts. Experiments have been carried out at the operating capacity of 2 L and constant initial pH of 12.5. The effect of catalyst loading on the sonochemical degradation has been investigated by varying the loading over the range of 1.5–4.5 g/L. It has been observed that the maximum degradation of 52.2% was obtained at an optimum concentration of CuO as 1.5 g/L whereas for TiO₂ maximum degradation was observed as 51.2% at a loading of 4 g/L over similar treatment period. Studies with presence of radical scavengers such as methanol (CH₃OH) and n-butanol (C₄H₉OH) indicated lower extents of degradation confirming the dominance of radical mechanism. The combined approach of ultrasound, solid catalyst and scavengers has also been investigated at optimum loadings to simulate real conditions. The optimal solid loading was used for studies involving oxidation using UV irradiations where 26.4% and 28.9% of degradation was achieved at optimal loading of CuO and TiO_2, respectively. Studies using combination of UV and US irradiations have also been carried out using the optimal concentration of the catalysts. It has been observed that maximum degradation of 63.3% is achieved using combined US and UV with TiO₂ (4 g/L) as the photocatalyst. Overall it can be said that the combined processes give higher extent of degradation as compared to the individual processes based on US or UV irradiations.     

Spectroscopic properties of Co2+: ZnAl2O4 nanocrystals in sol–gel derived glass–ceramics

Transparent glass–ceramics containing zinc–aluminum spinel (ZnAl₂O₄) nanocrystals doped with tetrahedrally coordinated Co²⁺ ions were obtained by the sol–gel method for the first time. The gels of composition SiO₂–Al₂O₃–ZnO–CoO were prepared at room temperature and heat-treated at temperature ranging 800–950 °C. When the gel samples were heated up to 900 °C, ZnAl₂O₄ nanocrystals were precipitated. Co²⁺ ions were located in tetrahedral sites in ZnAl₂O₄ nanocrystals. X-ray diffraction analysis shows that the crystallite sizes of ZnAl₂O₄ crystal become large with the heat-treatment temperature and time, and the crystallite diameter is in the range of 10–15 nm. The dependence of the absorption and emission spectra of the samples on heat-treatment temperature were presented. The difference in the luminescence between Co²⁺ doped glass–ceramic and Co²⁺ doped bulk crystal was analysed. The crystal field parameter D_q of 423 cm⁻¹ and the Racah parameters B of 773 cm⁻¹ and C of 3478.5 cm⁻¹ were calculated for tetrahedral Co²⁺ ions.     

Structural characterization of the V2O5/TiO2 system obtained by the sol–gel method

The influence of the vanadium load and calcination temperature on the structural characteristics of the V₂O₅/TiO₂ system was studied by X-ray diffraction and X-ray absorption spectroscopy (XAS) techniques. Samples of the V₂O₅/TiO₂ system were prepared by the sol–gel method under acid conditions and calcined at different temperatures. The rutile phase was found to predominate in pure TiO₂ calcined at 450 °C as a result of the reduction of phase transition temperature promoted by the sol–gel method under acid conditions. The anatase phase became predominant at 450 °C as the amount of vanadium increased from 6 to 9 wt%. A structural change in the TiO₂ phase from predominantly anatase to totally rutile with increased calcination temperature was observed in 6 wt% samples. An analysis of the vanadium X-ray Absorption Near Edge Structure (XANES) spectra showed that the oxidation state of vanadium atoms in the samples containing 6 and 9 wt% of vanadium and calcined at 450 °C was predominantly V⁴⁺. However, the presence of V⁵⁺ atoms cannot be ruled out. A qualitative analysis of extended X-ray absorption fine structure (EXAFS) spectra of the samples containing 6 and 9 wt% of vanadium calcined at 450 °C showed that the local structure around vanadium atoms is comparable to that of VO₂ crystalline phase, in which vanadium atoms are fourfold coordinated in a distorted structure. For the sample after calcination at 600 °C, the EXAFS and XANES results showed that a significant portion of vanadium atoms were incorporated in the rutile lattice with a V_xTi_(1−x)O₂ solid solution formation. The conditions of sample preparation used here to prepare V₂O₅/TiO₂ samples associated with different amounts of vanadium and calcination temperatures proved to be useful to modifying the structure of the V₂O₅/TiO₂ system.     

Nb doping effect on TiO2−x films for bolometer applications

Nb-doped TiO_2−x thin films were deposited using a 1 at% niobium doped titanium target by RF reactive magnetron sputtering at various oxygen partial pressures (pO₂). The films appeared amorphous in the pO₂ range of 4.4–4.7% with resistivity ranging from 0.39 Ω cm to 2.48 Ω cm. Compared to pure TiO_2−x films, the resistivity of the Nb-doped TiO_2−x films did not change sensitively with the oxygen partial pressure, indicating that the resistivity of the films can be accurately controlled. 1/f noise parameter of Nb-doped TiO_2−x films were found to decrease largely while the measured temperature coefficient of resistance (TCR) of the films was still high. The obtained results indicate that Nb-doped TiO_2−x films have great potential as an alternative bolometric material.     

Ultrasound assisted two-stage biodiesel synthesis from non-edible Schleichera triguga oil using heterogeneous catalyst: Kinetics and thermodynamic analysis

Present work deals with the ultrasound-assisted biodiesel production from low cost, substantial acid value kusum (Schleichera triguga) oil using a two-step method of esterification in presence of acid (H₂SO₄) catalyst followed by transesterification using a basic heterogeneous barium hydroxide (Ba(OH)₂) catalyst. The initial acid value of kusum oil was reduced from 21.65 to 0.84 mg of KOH/g of oil, by acid catalyzed esterification with 4:1 methanol to oil molar ratio, catalyst concentration 1% (v/v), ultrasonic irradiation time 20 min at 40 °C. Then, Ba(OH)₂ concentration of 3% (w/w), methanol to oil molar ratio of 9:1, ultrasonic irradiation time of 80 min, and temperature of 50 °C was found to be the optimum conditions for transesterification step and triglyceride conversion of 96.8% (wt) was achieved. This paper also examined the kinetics as well as the evaluation of thermodynamic parameters for both esterification and transesterification reactions. The lower value of activation energy and higher values of kinetic constants indicated a fast rate of reaction, which could be attributed to the physical effect of emulsification, in which the microturbulence generated due to radial motion of bubbles, creates an intimate mixing of the immiscible reactants causing the increase in the interfacial area, giving faster reaction kinetics. The positive values of Gibbs-free energy (ΔG), enthalpy (ΔH) and negative value of entropy (ΔS) revealed that both the esterification and transesterification were non-spontaneous, endothermic and endergonic reactions. Therefore, the present work has not only established the escalation obtained due to ultrasonication but also exemplified the two-step approach for synthesis of biodiesel from non-edible kusum oil based on the use of heterogeneous catalyst for the transesterification step.     

Preparation of (5.0%)Er3+:Y3Al5O12/Pt-(TiO2-Ta2O5) nanocatalysts and application in sonocatalytic decomposition of ametryn in aqueous solution

(5.0%)Er³⁺:Y₃Al₅O₁₂/Pt-(TiO₂-Ta₂O₅) powder, as a high effective sonocatalyst, was prepared using sol-gel and calcination method. Then it was characterized by X-ray diffractometer (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDX). In order to evaluate the sonocatalytic activity of the prepared (5.0%)Er³⁺:Y₃Al₅O₁₂/Pt-(TiO₂-Ta₂O₅) powder, the sonocatalytic decomposition of ametryn was studied. In addition, some influencing factors such as different Ti/Ta molar ratios on the sonocatalytic activity of the prepared (5.0%)Er³⁺:Y₃Al₅O₁₂/Pt-(TiO₂-Ta₂O₅) powder, catalyst added amount with ultrasonic irradiation time and used times on the sonocatalytic decomposition efficiency were examined by using ion chromatogram determination. The experimental results showed that the best sonocatalytic decomposition ratio of ametryn were 77.50% based on the N atom calculation and 95.00% based on the S atom calculation, respectively, when the conditions of 10.00 mg/L initial concentration, 1.00 g/L prepared (5.0%)Er³⁺:Y₃Al₅O₁₂/Pt-(TiO₂-Ta₂O₅) powder (Ti/Ta = 1.00:0.25 heat-treated at 550 °C for 3.0 h) added amount, 150 min ultrasonic irradiation (40 kHz frequency and 300 W output power), 100 mL total volume and 25–28 °C temperature were adopted. Therefore, the (5.0%)Er³⁺:Y₃Al₅O₁₂/Pt-(TiO₂-Ta₂O₅) composite nanoparticles could be considered as an effective sonocatalyst for decomposition of ametryn in aqueous solution.     

Effects of doping with nanoscale Co3O4 particles on the superconducting properties of powder-in-tube processed MgB2 tapes

Nanoscale Co₃O₄ particles were doped into MgB₂ tapes with the aim of developing superconducting wires with high-current-carrying capacity. Fe-sheathed MgB₂ tapes with a mono-core were prepared using the in situ powder-in-tube (PIT) process with the addition of 0.2–1.0 mol% Co₃O₄. The critical temperature decreased monotonically with an increasing amount of doped Co₃O₄ particles for all heat-treatment temperatures from 600 to 900 °C. However, the transport critical current density (J_c) at 4.2 K varied with the heat-treatment temperatures. The J_c values in magnetic fields ranging from 7 to 12 T decreased monotonically with increasing Co₃O₄ doping level for a heat-treatment temperature of 600 °C. In contrast, some improvements on the J_c values of the Co₃O₄ doped tapes were observed in the magnetic fields below 10 T for 700 and 800 °C. Furthermore, J_c values in all the fields measured increased as the Co₃O₄ doping level increase from 0 to 1 mol% for 900 °C. This heat-treatment temperature dependence of the J_c values could be explained in terms of the heat-treatment temperature dependence of the irreversibility field with Co₃O₄ doping.     

Preparation and photocatalytic degradation of erbium doped titanium dioxide nanorods

Photocatalytic degradation of methylene blue (MB) in water was examined using Er³⁺-doped TiO₂ (Er–TiO₂) nanorods prepared by a sol–gel derived electrospinning, calcination, and subsequent mechanical grinding. Different concentrations of Er dopant in the range of 0–1.0 mol% were synthesized to evaluate the effect of Er content on the photocatalytic activity of TiO₂. Among Er³⁺–TiO₂ catalysts, the 0.7 mol% Er³⁺–TiO₂ catalyst showed the highest MB degradation rate. The degradation kinetic constant (k) increased from 1.0 × 10^?3 min^?1 to 5.1 × 10^?3 min^?1 with the increase of Er³⁺ doping from 0 to 0.7 mol%, but decreased down to 2.1 × 10^?3 min^?1 when Er³⁺ content was 1.0 mol%. It can be concluded that the degradation of MB under UV radiation was more efficient with Er³⁺–TiO₂ catalyst than with pure TiO₂. The higher activity might be attributed to the transition of 4f electrons of Er³⁺ and red shifts of the optical absorption edge of TiO₂ by erbium ion doping.     

Phase formation and electrical properties of BNLT–BZT lead-free piezoelectric ceramic system

Phase formation study in lead-free piezoelectric ceramics based on lanthanum doped bismuth sodium titanate (Bi_0.4871Na_0.4871La_0.0172TiO₃:BNLT) and zirconium doped barium titanate (BaZr_0.05Ti_0.95O₃:BZT), has been carried out in the system of (1−x)BNLT–xBZT where x = 0.0–1.0, by two-step mixed oxide method. It was observed that the addition of BZT in the BNLT ceramics developed the dielectric and piezoelectric properties of the ceramics with the optimum piezoelectric constant (d₃₃) and dielectric constant (ε_r) at room temperature of about 138 pC/N and 1651, respectively, from the 0.2 BNLT to 0.8 BZT ceramic sample. The Curie temperature (T_C) of this ceramic was found at 295 °C which is 195 °C higher than that of pure BZT ceramics, promising the use of this ceramic in a higher range of temperature.     

Effect of Fe doping on the room temperature ferromagnetism in chemically synthesized (In1−xFex)2O3 (0 ⩽ x ⩽ 0.07) magnetic semiconductors

Observation of room temperature ferromagnetism in Fe doped In₂O₃ samples (In_1−xFe_x)₂O₃ (0 ⩽ x ⩽ 0.07) prepared by co-precipitation technique is reported. Lattice parameter obtained from powder X software shows distinct shrinkage of the lattice constant indicating an actual incorporation of Fe ions into the In₂O₃ lattice. X-ray diffraction data measurements show that the entire sample exhibits single phase polycrystalline behavior. SEM micrographs showed the prepared powder was in the range 25–36 nm. SEM EDS mapping showed the presence of Fe and In ions in the Fe doped In₂O₃ sample. The highest remanence magnetization moment (6.624 × 10⁻⁴ emu/g) is reached in the sample with x = 0.03.     

Electrical properties of yttrium doped strontium titanate with A-site deficiency as potential anode materials for solid oxide fuel cells

Yttrium doped strontium titanate with A-site deficiency ((Y_0.08Sr_0.92)_1 ? xTiO_3 ? δ) was synthesized by conventional solid state reaction. The deficiency limit of A-site in (Y_0.08Sr_0.92)_1 ? xTiO_3 ? δ is below 6 mol% in Ar/H₂ (5%) at 1500 °C. The sinterability of (Y_0.08Sr_0.92)_1 ? xTiO_3 ? δ samples decreases slightly with increasing A-site deficiency level (x). The ionic conductivity of (Y_0.08Sr_0.92)_1 ? xTiO_3 ? δ samples increases while the electronic conductivity decreases with increasing A-site deficient amount. The defect chemistry analysis indicates that the introduction of A-site deficiency results in not only the increase of oxygen vacancy concentration but also the decrease of Ti³⁺-ion concentration. The latter plays the main role in the electrical conduction. (Y_0.08Sr_0.92)_1 ? xTiO_3 ? δ shows good thermal-cyclic performance in electrical conductivity and has an excellent chemical compatibility with YSZ electrolyte below 1500 °C.     

Adsorption of thiophene on silica-supported Mo clusters

The adsorption/decomposition kinetics/dynamics of thiophene has been studied on silica-supported Mo and MoS_x clusters. Two-dimensional cluster formation at small Mo exposures and three-dimensional cluster growth at larger exposures would be consistent with the Auger electron spectroscopy (AES) data. Thermal desorption spectroscopy (TDS) indicates two reaction pathways. H₄C₄S desorbs molecularly at 190–400 K. Two TDS features were evident and could be assigned to molecularly on Mo sites, and S sites adsorbed thiophene. Assuming a standard preexponential factor (ν = 1 × 10¹³/s) for first-order kinetics, the binding energies for adsorption on Mo (sulfur) sites amount to 90 (65) kJ/mol for 0.4 ML Mo exposure and 76 (63) kJ/mol for 2 ML Mo. Thus, smaller clusters are more reactive than larger clusters for molecular adsorption of H₄C₄S. The second reaction pathway, the decomposition of thiophene, starts at 250 K. Utilizing multimass TDS, H₂, H₂S, and mostly alkynes are detected in the gas phase as decomposition products. H₄C₄S bond activation results in partially sulfided Mo clusters as well as S and C residuals on the surface. S and C poison the catalyst. As a result, with an increasing number of H₄C₄S adsorption/desorption cycles, the uptake of molecular thiophene decreases as well as the H₂ and H₂S production ceases. Thus, silica-supported sulfided Mo clusters are less reactive than metallic clusters. The poisoned catalyst can be partially reactivated by annealing in O₂. However, Mo oxides also appear to form, which passivate the catalyst further. On the other hand, while annealing a used catalyst in H/H₂, it is poisoned even more (i.e., the S AES signal increases). By means of adsorption transients, the initial adsorption probability, S₀, of C₄H₄S has been determined. At thermal impact energies (E_i = 0.04 eV), S₀ for molecular adsorption amounts to 0.43 ± 0.03 for a surface temperature of 200 K. S₀ increases with Mo cluster size, obeying the capture zone model. The temperature dependence of S₀(T_s) consists of two regions consistent with molecular adsorption of thiophene at low temperatures and its decomposition above 250 K. Fitting S₀(T_s) curves allows one to determine the bond activation energy for the first elementary decomposition step of C₄H₄S, which amounts to (79 ± 2) kJ/mol and (52 ± 4) kJ/mol for small and large Mo clusters, respectively. Thus, larger clusters are more active for decomposing C₄H₄S than are smaller clusters.     

Surface reactions of TiCl4 and Al(CH3)3 on GaAs(100) during the first half-cycle of atomic layer deposition

GaAs(100) was exposed to pulses of trimethylaluminum (TMA, Al(CH₃)₃) and titanium tetrachloride (TiCl₄) to mimic the first half-cycle of atomic layer deposition (ALD). Both precursors removed the 9.0 ± 1.6 Å-thick mixed oxide consisting primarily of As₂O₃ with a small Ga₂O component that was left on the surface after aqueous HF treatment and vacuum annealing. In its place, TMA deposited an Al₂O₃ layer, but TiCl₄ exposure left Cl atoms adsorbed to an elemental As layer. This suggests that oxygen was removed by the formation of a volatile oxychloride species. A small TiO₂ coverage of approximately 0.04 monolayer remained on the surface for deposition temperatures of 89 °C to 135 °C, but no TiO₂ was present from 170 °C to 230 °C. The adsorbed Cl layer chemically passivated the surface at these temperatures and blocked TiO₂ deposition even after 50 full ALD cycles of TiCl₄ and water vapor. The Cl and As layers desorbed simultaneously at higher temperature producing peaks in the temperature programmed desorption spectrum in the range 237–297 °C. This allowed TiO₂ deposition at 300 °C in single TiCl₄ pulse experiments. On the native oxide-covered surface where there was a higher proportional Ga oxide composition, TiCl₄ exposure deposited TiO₂.     

The structure and extinction of nonpremixed methane/nitrous oxide and ethane/nitrous oxide flames

Knowledge of combustion of hydrocarbon fuels with nitrogen-containing oxidizers is a first step in understanding key aspects of combustion of hypergolic and gun propellants. Here an experimental and kinetic-modeling study is carried out to elucidate aspects of nonpremixed combustion of methane (CH₄) and nitrous oxide (N₂O), and ethane (C₂H₆) and N₂O. Experiments are conducted, at a pressure of 1 atm, on flames stabilized between two opposing streams. One stream is a mixture of oxygen (O₂), nitrogen (N₂), and N₂O, and the other a mixture of CH₄ and N₂ or C₂H₆ and N₂. Critical conditions for extinction are measured. Kinetic-modeling studies are performed with the San Diego Mechanism. Experimental data and results of kinetic-modeling show that N₂O inhibits the flame by promoting extinction. Analysis of the flame structure shows that H radicals are produced in the overall chain-branching step 3H₂ + O₂ ? 2H₂O + 2H, in which molecular hydrogen is consumed. Hydrogen is also consumed in the overall step N₂O + H₂ ? N₂ + H₂O where stable products are formed. Inhibition of the flames by N₂O is attributed to competition between these two overall steps.     

Ultrasonic synthesis and photocatalytic characterization of H3PW12O40/TiO2 (anatase)

A novel H₃PW₁₂O₄₀/TiO₂ (anatase) composite photocatalyst was prepared by a high-intensity ultrasonic method using a lower temperature (80 °C) and was characterized by XRD and FT-IR. Its photocatalytic activity, using solar light, was evaluated through the degradation of organic dye methylene blue (MB) in aqueous. When MB solution (50 mg/l, 200 ml) containing H₃PW₁₂O₄₀/TiO₂ (anatase) (0.4 g) was degraded by solar irradiation after 90 min, the removal of concentration and TOC of MB reached 95% and 73%, respectively. The photocatalyst activity of H₃PW₁₂O₄₀/TiO₂ (anatase) was much higher than TiO₂ which was prepared in the same way. H₃PW₁₂O₄₀/TiO₂ remained efficient after five repeated experiments.     

Microwave synthesis of nitrogen doped Ti4O7 for photocatalytic applications

The nitrogen (N) doped Ti₄O₇ photocatalyst was prepared from urea as a nitrogen source by a microwave method. The resulting photocatalyst was characterized by X-ray diffraction (XRD), Field Emission Scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), UV–visible diffuse reflectance spectroscopy (UV–Vis DRS) and UV–vis spectroscopy (UV–Vis). 0.1 M N doped Ti₄O₇ photocatalyst exhibited methylene blue decomposition efficiency of 100% which was prepared by microwave treatment for above 30 min. Rate constant was found to be 0.028910 min⁻¹ in the first order kinetic.