Ce-EU-1分子筛的合成和表征

采用水热法,以溴化六甲双铵（HMBr2）为模板剂,硅溶胶、偏铝酸钠为硅铝源,以六水硝酸铈为铈源合成了稀土Ce-EU-1分子筛,并通过XRD、FTIR、紫外-可见漫反射光谱、热重分析（TG-DTG）和氮气吸附-脱附等测试手段对合成样品的孔道结构、物化性能及Ce的存在状态进行了表征。XRD结果表明,合成样品不仅具有很高的纯度和结晶度,为典型的立方有序排列的EU-1结构,而且部分Ce已取代Si或Al进入微孔分子筛的骨架。样品的FTIR图谱在980cm-1附近有明显的Si—O—Ce特征吸收峰,证明Ce存在于分子筛的骨架中。紫外-可见漫反射图谱显示,在253nm附近出现O—Ce之间的电子跃迁特征峰,进一步证明了Ce进入了分子筛骨架。氮气吸附-脱附结果表明了Ce的掺入对分子筛的物化性能和孔道结构产生了影响。同时考察了镧系其他金属离子（Ln：La、Nd、Sm和Gd）对EU-1分子筛的影响,发现随着镧系离子半径的减小,Ln-EU-1分子筛的相对结晶度逐渐降低,晶胞体积减小。     

ZnO/MCM-41复合材料的制备及其光谱性质

以硅酸钠(NaSiO3·9H2O)为硅源,三甲基十六烷基溴化铵(CTAB)为模板剂在碱性条件下水热合成介孔分子筛MCM-41,然后以其为主体,采用锌盐浸渍-灼烧的方法.在介孔分子筛MCM-41上负载了氧化锌(ZnO)纳米微粒,并通过扫描电子显微镜,红外光谱(1R).紫外可见吸收光谱(UV-Vis),N2-吸附脱附和荧光光谱等手段对产品进行了系列表征.结果表明,分子筛平均直径约为1.7μm,对不同温度下灼烧后得到的ZnO/MCM-41组装体的光谱性质进行研究表明介孔分子筛MCM-41的尺寸所限,制备出的ZnO粒子粒径小于2 nm.量子尺寸效应使得ZnO/MCM-41组装体中的ZnO纳米粒子的紫外可见吸收光谱及荧光光谱均发生蓝移.通过红外光谱分析得知ZnO负载到MCM-41上并没有改变介孔分子筛原有的骨架结构.     

纳米介孔分子筛Sm-MCM的合成与表征

利用有机相-水相界面共沉淀溶胶支持自组装方法制备了颗粒大小约为10~15 nm稀土嵌入纳米介孔分子筛Sm-MCM(1∶10)。其BET比表面积、孔容和孔径分别为621 m2.g-1,1.25 cm3.g-1和8.0 nm。稀土掺杂能改善纳米分子筛的尺寸2。9S i-MAS NMR分析测试出样品的波谱峰-44,-58,-67,-76,-89,-107,-110 ppm,分别对应七个不同化学环境q0,q1,q2,q3,Q2,Q3,Q4[(S iO)4-nS i—(O—Sm—)n(n=4,3,2,1),(S iO)4-mS i—(OH)m(m=2,1,0)]。表明稀土元素已嵌入分子筛的骨架。不同的样品的巨大比表面积和大的孔容比表明分子筛为典型的介孔结构,也说明这些介孔物质材料在800℃的高温下有非常好的热稳定性。把硅胶基质介孔分子筛的红外吸收峰970 cm-1归属为硅羟基的扭曲振动。Sm-MCM的发射光谱归属于Sm3+离子的4L17/2→6Hn/2(n=11,13,15)跃迁发射。     

飞秒激光烧蚀合成Y_2O_3∶Pr~(3+),Yb~(3+)上转换发光材料

利用飞秒激光烧蚀方法合成了Y2O3∶Pr3+,Yb3+纳米颗粒并对其上转换发光性质进行了研究。对合成产物的形貌分析显示,在一定的激光烧蚀功率密度下,即可制备出小尺寸的纳米颗粒,提高激光功率密度可以得到更高的纳米颗粒产量,所获得的纳米颗粒尺寸小于50 nm。荧光测试结果表明,Y2O3∶Pr3+,Yb3+纳米颗粒具有510 nm为中心的上转换发光带,上转换发光随纳米颗粒数量的增加而增强。     

CVD法制备碳纳米管的TG-DTA研究--温度对CVD法制备碳纳米管的影响

基于碳纳米管粗产品中无定形碳和不同直径碳纳米管对氧的反应活性的差异 ,通过差热 -热重 (TG DTA)方法 ,结合透射电镜 (TEM)和X射线衍射 (XRD)的测试结果 ,研究了合成温度对以乙炔气体为碳源 ,用CVD法制备碳纳米管的石墨化程度、碳纳米管直径以及直径分布的影响 .结果表明 :反应中 ,由于催化剂Co/SiO2中活性组分 (Co)微晶随合成温度的升高而增大 ,导致所制备的碳纳米管的直径增大 ,从 2 0～ 30nm (6 5 0℃ )增加到 30～ 5 0nm (75 0℃ ) .碳纳米管的石墨化程度随着反应温度的升高而增加 .XRD实验结果还表明 ,当合成温度从 6 5 0℃增加到 85 0℃时 ,2θ值从 2 5 .8°增加到 2 6 .8°,(0 0 2 )晶面的层间距从 3.45 减小到 3.32 ,即随着合成温度的升高 ,碳纳米管 (0 0 2 )晶面的层间距减小 .通过DTA放热峰的峰温和半峰宽的分析得出 ,无定形碳的放热峰峰温Tp<380℃ ,其含量随着温度的升高而减小 .碳纳米管的DTA放热峰的峰温Tp 随着碳纳米管的直径和石墨化的程度的增加而升高 ,半峰宽随着碳纳米管的直径的分布范围增大而增宽 .低温 (6 5 0℃ )有利于生成直径小且均匀的多层碳纳米管 (2 0～ 30nm) ,而高温 (大于 75 0℃ )则有利于生成直径大的多层碳纳米管 (大于 30～5 0nm) .     

高质量AlPO4-5分子筛大单晶的合成与表征

以拟薄水铝石作为铝源,正磷酸为磷源,正三丙胺(TPA)作模板剂,采用水热法合成了AlPO4 5分子筛.在不同的反应物配比、温度以及晶化时间条件下,得到了不同尺寸的AlPO4 5分子筛单晶.实验表明,反应物质的摩尔比为Al2O3∶P2O5∶TPA∶C2H5OH∶H2O∶HF=1∶1. 2∶2. 66∶80∶1000∶0. 7,反应温度为457K,晶化时间48h是生成六方AlPO4 5分子筛大单晶较适宜的条件;在该反应条件下合成出纵向尺度最大达到2. 0mm、具有完整六方棱柱形态的AlPO4 5分子筛单晶;部分晶体的横向尺度达到0. 31mm.用扫描电镜观察晶体的形貌;AlPO4 5分子筛晶体结构通过SMART1000单晶衍射仪鉴定.     

聚苯胺-碳纳米管复合体的制备及其光响应

纳米尺寸导电材料对功能分子材料及分子器件的作用越来越显得重要.采用原位乳液聚合法制备聚苯胺 碳纳米管复合体，SEM和TEM照片显示复合管的直径为60—70nm，聚苯胺的包裹层厚度约25—30nm.x射线衍射及热分析表明纳米复合管的结晶性能增强，热稳定性得到提高.光电响应试验表明复合管的光吸收增强，光电流增大，说明聚苯胺 碳纳米复合管薄膜受光照射后发生了光诱导电荷分离现象. 关键词： 聚苯胺 碳纳米管 复合纳米管 光电流     

高质量AIP04-5分子筛大单晶的合成与表征

以拟薄水铝石作为铝源，正磷酸为磷源，正三丙胺(TPA)作模板剂，采用水热法合成了AIPO4-5分子筛．在不同的反应物配比、温度以及晶化时间条件下，得到了不同尺寸的AIPO4-5分子筛单晶．实验表明，反应物质的摩尔比为Al2O3：P2O5：TPA：C2H5OH：H2O：HF=1：1．2：2．66：80：1000：0．7，反应温度为457K，晶化时间48h是生成六方AIPO4-5分子筛大单晶较适宜的条件；在该反应条件下合成出纵向尺度最大达到2．0mm、具有完整六方棱柱形态的MPO4-5分子筛单晶；部分晶体的横向尺度达到0．31mm．用扫描电镜观察晶体的形貌：AlPO4-5分子筛晶体结构通过SMART1000单晶衍射仪鉴定．     

纳米晶Gd2O3：Eu^3＋的制备及发光性能

采用低温燃烧合成法制备了Gd2O3：Eu^3＋纳米晶。用X射线衍射仪（XRD）、高分辨透射电子显微镜（HRTEM）和荧光光谱仪分别对样品的结构、形貌和发光性能进行了研究。结果表明，改变甘氨酸与稀土离子的比例（G／M）、退火温度可以制备出不同结构和晶粒尺寸的Gd2O3：Eu^3＋纳米晶。在退火温度为800℃，G／M等于0．83和1．0时，均得到了纯立方相的Gd2O3：Eu^3＋纳米晶，随着G／M的增加，Gd2O3：Eu^3＋从立方相逐渐向单斜相转变。粉末的晶粒尺寸随着退火温度的增高而增大，晶粒尺寸在10-30nm之间。立方相的Gd2O3：Eu^3＋纳米晶主发射峰位置在612nm（^5D^0→^7F2跃迁），激发光谱中电荷迁移态发生了红移。     

一维取向LTL型分子筛荧光阵列的快速组装

通过有效控制合成液配比,合成出了形貌规则、结晶度高且具有不同长径比的LTL型分子筛晶粒。采用"瓶中造船法",在不同长径比的LTL型分子筛晶粒孔道中组装稀土有机配合物,制得LTL分子筛/Eu-TTA主-客体荧光材料。荧光光谱表征结果表明,在激发波长为350 nm时,长径比为0.2的LTL分子筛/Eu-TTA晶粒在617 nm处的5D0→7F2发光强度最大,而长径比为3的晶粒发光强度最小。最后,将长径比为0.2的LTL分子筛/Eu-TTA晶粒在PEI修饰的玻璃表面快速擦涂10 s后,就制得厘米尺寸的一维取向LTL型分子筛荧光阵列。SEM表征结果证实,该分子筛荧光阵列中几乎所有的LTL分子筛晶粒都沿着与底基表面垂直的c轴方向一维高密度、单层有序排列。在激发波长为365 nm时,该一维取向LTL分子筛荧光阵列发出鲜艳的红色荧光。     

Self-organization of five species in a cyclic competition game

Cyclic competition game models, particularly the “rock–paper–scissors” model, play important roles in exploring the problem of multi-species coexistence in spatially ecological systems. We propose an extended “rock–paper–scissors” game to model cyclic interactions among five species, and find that two of the five can coexistent when biodiversity disappears, which is different from the “rock–paper–scissors” game. As the number of fingers is five, we named the new model the “fingers” game, where the thumb, forefinger, middle finger, ring finger, and little finger cyclically dominate their subsequent species and are dominated by their former species. We investigate the “fingers” model in two ways: direct simulations and nonlinear partial differential equations. An important finding is that the number of species in a cyclic competition game has an influence on the emergence of biodiversity. To be specific, the “rock–paper–scissors” model is in favor of maintaining biodiversity in comparison with the “fingers” model when the variables (population size, reproduction rate, selection rate, and migration rate) are the same. It is also shown that the mobility and reproduction rate can promote or jeopardize biodiversity.     

Experimental study on downstep in Chinese intonation

Downstep in pitch contour of Chinese Putonghua is examined using subtly designed sentences by controlling tone combinations. The results show both automatic and nonautomatic downstep phenomena exist in Chinese. In non-automatic downstep, low tones compress downwards the pitch range of the following syllables. and the main influence of downstep is on topline. Low tone not only lower the topline behind it, but also raise the high tones before it, the effects are compatible with each other. In automatic downstep, the topline of pitch contour in intonational phrase is presented as a linear downtrend, but it differs among speakers due to the effect of personal stress practice. In comparison with downstep phenomenon in other tone or non-tone languages, the downstep ratio in Chinese is not constant, and the domain of downstep is not limited within the adjacent tones.     

Contrastive analysis on tone between Putonghua and Taiwan Mandarin

The differences of the pitch and duration of Chinese syllables between Putonghua （PTH） and Taiwan Mandarin （TM） were studied. The speech materials to be used are not only isolated syllables, but also sentences. The results reveal that： For the isolated syllables, T1 and T2 in TM are influenced by Minnan dialect, therefore their pitch are lower than those in PTH. T3 is fall-rise in PTH, while it is fall in TM. Moreover, the syllable duration sequence for different tone is T3〉T2〉T1〉T4 in PTH, while it is T1〉T2〉T3〉T4 in TM. For the syllables in sentences, T2 is mid-rise in PTH, while it is mid-level in TM. And the T3 is longer than T4 but shorter than T1 or T2 in PTH, while it is the shortest in TM. Furthermore the effects of prosodic phrase boundary on duration for different tones are almost the same in PTH, but the lengthening part of T1 or T2 is longer than that of T3 or T4 in TM.     

Abelian-Higgs phase of SU(2) QCD and glueball energy

It is shown that SU(2) QCD admits an dual Abelian-Higgs phase, with a Higgs vacuum of a type-Ⅱ superconductor. This is done by using a connection decomposition for the gluon field and the random-direction approximation. Using a bag picture with soft wall, we presented a calculational procedure for the glueball energy based on the recent proof for wall-vortices [Nucl. Phys. B 741(2006)1].     

High efficiency filtering using two-dimensional photonic crystal coupled cavity structures

Transmission spectra of coupled cavity structures (CCSs) in two-dimensional (2D) photonic crystals (PCs) are investigated using a coupled mode theory, and an optical filter based on CCS is proposed. The performance of the filter is investigated using finite-difference time-domain (FDTD) method, and the results show that within a very short coupling distance of about 3λ, where λ is the wavelength of signal in vacuum, the incident signals with different frequencies are separated into different channels with a contrast ratio of 20 dB. The advantages of this kind of filter are small size and easily tunable operation frequencies.     

Signal generation in an isotropic medium in scanning electron acoustic microscope

Based on the research in Ref. [5][Materials Science and Engineering, 1989; A122： 57 63], an improved model of heat source is set up, the different modes of Lamb wave in an isotropic sample generated by a chopped electron beam at frequency f are obtained with integral transform and normal function expansion method, and the output signal of PZT coupled at the back surface of the sample is found out. The generation mechanism of SEAM （Scanning Electron Acoustic Microscopy） signal is discussed. It shows that the SEAM is a near field imaging technique with high spatial resolution and its best lateral spatial resolution is about 2√2α （α is the radius of the focused electron beam）. Some of experimental results of SEAM images are presented in the paper and it shows that the spatial resolution of SEAM is better than 0.5 μm and smaller than the thermal diffusion length of the sample. Therefore the character of near field imaging in SEAM is also proved experimentally.     

Real-time restoration of rotational blurred image using gradient-loading

The key to the restoration of rotational motion blurred image is how to restore the image under a low cost and to correct the irreversibility of the degradation function matrix.Based on the special qualities of degradation function matrix and precise deduction in space-domain, we present a new approach using gradient-loading for restoration of rotational blurred image.By easily adding a gradient operator, the irreversibility of the original matrix is corrected and can be applied for inverse filtering then.Gradientloading is the optimized approach which combines the advantages of both the approaches using constrained least square filtering and traditional diagonal-loading.Compared with the approach using least square filtering, its peak signal-to-noise ratio (PSNR) is improved from 3.18 to 6.46dB, while the computing time is reduced to 1/2-1/3.Experimental results demonstrate the effectiveness, noise-resistibility, robustness, and low complexity of this approach, which make it more suitable for real-time environment.     

All-Optical Logic Device Using Bent Nonlinear Tapered Y-Junction Waveguide Structure

We propose an all-optical logic device made of a bent tapered Y-junction waveguide with a Kerr-type nonlinear interface. It could provide an AND gate, OR gate, and exclusive-OR (XOR) gate. We could obtain different transmission results by adjusting the bending angle. The numerical simulation results show that the device functions as AND, OR, and XOR gates.     

Real-time, continuous-wave terahertz imaging by a pyroelectric camera

Real-time, continuous-wave terahertz (THz) imaging is demonstrated. A 1.89-THz optically-pumped farinfrared laser is used as the illumination source, and a 124 × 124 element room-temperature pyroelectric camera is adopted as the detector. With this setup, THz images through various wrapping materials are shown. The results show that this imaging system has the potential applications in real-time mail and security inspection.