Synthesis and hyperthermia property of hydroxyapatite-ferrite hybrid particles by ultrasonic spray pyrolysis

Biocompatible hybrid particles composed of hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂, HAp) and ferrite (γ-Fe₂O₃ and Fe₃O₄) were synthesized using a two-step procedure. First, the ferrite particles were synthesized by co-precipitation. Second, the suspension, which was composed of ferrite particles by a co-precipitation method, Ca(NO₃)₂, and H₃PO₄ aqueous solution with surfactant, was nebulized into mist ultrasonically. Then the mist was pyrolyzed at 1000 °C to synthesize HAp-ferrite hybrid particles. The molar ratio of Fe ion and HAp was (Fe²⁺ and Fe³⁺)/HAp=6. The synthesized hybrid particle was round and dimpled, and the average diameter of a secondary particle was 740 nm. The cross section of the synthesized hybrid particles revealed two phases: HAp and ferrite. The ferrite was coated with HAp. The synthesized hybrid particles show a saturation magnetization of 11.8 emu/g. The net saturation magnetization of the ferrite component was calculated as 32.5 emu/g. The temperature increase in the AC-magnetic field (370 kHz, 1.77 kA/m) was 9 °C with 3.4 g (the ferrite component was 1.0 g). These results show that synthesized hybrid particles are biocompatible and might be useful for magnetic transport and hyperthermia studies.     

Tunable polymer waveguide Bragg filter fabricated by direct patterning of UV-curable polymer

Tunable polymer wavelength filters are demonstrated using a silicon-nitride grating which gives high refractive index contrast with polymers. The polymer waveguides are defined using direct patterning of a liquid-state UV-curable polymer by proximate-contact lithography technique. The wavelength filter exhibits a narrow bandwidth of less than 1.0 nm and a transmission dip of more than −15 dB. The peak wavelength is shifted over 10 nm in the temperature range of 25-70 °C and the thermal tuning efficiency is −0.212 nm/°C.     

Synthesis of CdSe/CdS with a simple non-TOP-based route

A convenient and non-TOP-based route for the synthesis of core-shell CdSe/CdS quantum dots (QDs) is developed for the first time. Simple reagents, such as cadmium oxide, selenium powder, sodium sulfide, paraffin and oleic acid with obvious advantages are used to replace organometallics. This simple route allows the preparation of a series of core-shell CdSe/CdS QDs emitting in a wide wavelength range (from 510 to 615 nm). After passivation of CdSe by CdS shell using sodium sulfide as the source of sulfur at 80 °C, the quantum yields (QYs) are improved from 15-30% to 35-50% and remained stable at least for 4 months. A narrow bandwidth (FWHM<50 nm) indicates that the as-prepared QDs have uniform size distribution, desirable dispersibility and good fluorescence properties. The whole procedure can be carried out either open to air or under nitrogen atmosphere, which is simpler, greener and cheaper as compared with TOP-based route.     

32-channel arrayed waveguide grating multiplexer using low loss fluorinated polymer operating around 1550 nm

A 32 × 32 arrayed waveguide grating (AWG) multiplexer operating around the 1550 nm wavelength has been designed and fabricated using highly fluorinated polyethers. The propagation loss of the slab waveguide is about 0.3 dB/cm at 1550 nm wavelength. The channel spacing of the AWG multiplexer is 0.8 nm (100 GHz). The insertion loss of the multiplexer is 10.3-15.3 dB and the crosstalk is less than −20 dB.     

Influence of oxygen partial pressure on the properties of pulsed laser deposited nanocrystalline zirconia thin films

ZrO₂ thin films were deposited at various oxygen partial pressures (2.0 × 10⁻⁵-3.5 × 10⁻¹ mbar) at 973 K on (1 0 0) silicon and quartz substrates by pulsed laser deposition. The influence of oxygen partial pressure on structure, surface morphology and optical properties of the films were investigated. X-ray diffraction results indicated that the films are polycrystalline containing both monoclinic and tetragonal phases. The films prepared in the oxygen partial pressures range 2.0 × 10⁻⁵-3.5 × 10⁻¹ mbar contain nanocrystals of sizes in the range 54-31 nm for tetragonal phase. The peak intensity of the tetragonal phase decreases with the increase of oxygen partial pressures. Surface morphology of the films examined by AFM shows the formation of nanostructures. The RMS surface roughness of the film prepared at 2.0 × 10⁻⁵ mbar is 1.3 nm while it is 3.2 nm at 3.5 × 10⁻¹ mbar. The optical properties of the films were investigated using UV-visible spectroscopy technique in the wavelength range of 200-800 nm. The refractive index is found to decrease from 2.26 to 1.87 as the oxygen partial pressure increases from 2.0 × 10⁻⁵ to 3.5 × 10⁻¹ mbar. The optical studies show two different absorption edges corresponding to monoclinic and tetragonal phases.     

In-fiber Mach–Zehnder interferometer based on multi-mode fiber and up-taper for curvature sensing

A new type of curvature sensor comprises a stub of multi-mode fiber and an up-taper is proposed and demonstrated experimentally. The whole fabrication process is quite simple and the sensor head is cost effective. Measurement results show that it has a maximum curvature sensitivity of −61.877 nm/m⁻¹ at 1.1718 m⁻¹ (the highest value of reported papers among in-fiber Mach–Zehnder interferometers) and −9.2115 nm/m⁻¹ from 0.865 m⁻¹ to 1.1172 m⁻¹. Temperature sensitivity of 89.01 pm/°C within the range of 20–80 °C has also been achieved, which implies the possibility for measurement of temperature.     

Growth and characterization of ZnO-SDS hybrid thin films prepared by electrochemical self-assembly method

ZnO-SDS hybrid thin films were grown on ITO glass using the potentiostatic electrodeposition route from aqueous zinc nitrate solution containing surfactant sodium dodecyle sulfanate (SDS). The electrochemical process of the hybrid films was analyzed by comparing the cyclic voltammetric curve and current-time curve with those of pure ZnO film. Results showed that the addition of a small amount of SDS could decrease the deposition current density, and inhibit the growth of ZnO crystals significantly. The hybrid films electrodeposited at −0.9 V for 30 min exhibited smooth and platelet-like morphology, with the film thickness of about 110 nm. The well-defined ZnO-SDS lamellar structures could be clearly observed, with two interlayer spaces of 35.1 and 30.9 Å, respectively. Optical analysis showed that the hybrid films had good optical quality, and exhibited the fundamental absorption edge of ZnO at 380 nm.     

Indium zinc oxide thin films deposited by sputtering at room temperature

The deposition of amorphous indium zinc oxide (IZO) thin films on glass substrates with n-type carrier concentrations between 10¹⁴ and 3 × 10²⁰ cm⁻³ by sputtering from single targets near room temperature was investigated as a function of power and process pressure. The resistivity of the films with In/Zn of ∼0.7 could be controlled between 5 × 10⁻³ and 10⁴ Ω cm by varying the power during deposition. The corresponding electron mobilities were 4-18 cm² V⁻¹ s⁻¹.The surface root-mean-square roughness was <1 nm under all conditions for film thicknesses of 200 nm. Thin film transistors with 1 μm gate length were fabricated on these IZO layers, showing enhancement mode operation with good pitch-off characteristics, threshold voltage 2.5 V and a maximum transconductance of 6 mS/mm. These films look promising for transparent thin film transistor applications.     

Chemical composition of ZrC thin films grown by pulsed laser deposition

ZrC films were grown on (1 0 0) Si substrates by the pulsed laser deposition (PLD) technique using a KrF excimer laser working at 40 Hz. The nominal substrate temperature during depositions was set at 300 °C and the cooling rate was 5 °C/min. X-ray diffraction investigations showed that films deposited under residual vacuum or under 2 × 10⁻³ Pa of CH₄ atmosphere were crystalline, exhibiting a (2 0 0)-axis texture, while those deposited under 2 × 10⁻² Pa of CH₄ atmosphere were found to be equiaxed and with smaller grain size. The surface elemental composition of as-deposited films, analyzed by Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS), showed the usual high oxygen contamination of carbides. Once the topmost 2-4 nm region was removed, the oxygen concentration rapidly decreased, down to around 3-8% only in bulk. Simulations of the X-ray reflectivity (XRR) curves indicated a smooth surface morphology, with roughness values below 1 nm (rms) and films density values of around 6.30-6.45 g/cm³, very close to the bulk density. The growth rate, estimated from thickness measurements by XRR was around 8.25 nm/min. Nanoindentation results showed for the best quality ZrC films a hardness of 27.6 GPa and a reduced modulus of 228 GPa.     

Numerical design of high nonlinear coefficient of microstructure optical fibers

This paper presents a theoretical design of highly nonlinear microstructure optical fiber with dispersion-flat characteristics. The APSS™ 2.3 software based on the finite difference method with perfectly matched boundary conditions is used to simulate the properties of the proposed microstructure optical fiber. According to simulation, the proposed fiber warrants a high nonlinear coefficient of the order 41 W⁻¹ km⁻¹ and a low dispersion of 0.25 ps/nm/km at 1550 nm wavelength. It assumes a dispersion-flat characteristic of 0 ± 0.50 ps/nm/km in a 1450-1620 nm wavelength range centering 1550 nm wavelength with a modest number of design parameters.