首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到17条相似文献,搜索用时 78 毫秒
1.
激光熔覆TiC陶瓷涂层的组织和摩擦磨损性能研究   总被引:6,自引:0,他引:6  
孙荣禄  杨贤金 《光学技术》2006,32(2):287-289
采用激光熔覆技术在TC4合金表面上制备了TiC陶瓷涂层,分析了熔覆层的微观组织,测试了熔覆层的硬度和摩擦磨损性能。结果表明:TiC激光熔覆层分为熔覆区和稀释区两个区域,熔覆区未受到基底的稀释,由TiC颗粒和TiC树枝晶组成;稀释区受到了基底的稀释,由TiC树枝晶和钛合金组成;TiC激光熔覆层的显微硬度在HV700~1500之间,明显地改善了TC4合金表面的摩擦和磨损性能。  相似文献   

2.
激光熔覆NiCrBSi涂层组织及摩擦磨损性能   总被引:3,自引:0,他引:3  
采用激光熔覆技术在H13钢表面制备了NiCrBSi合金涂层,利用OM,SEM,EDX和XRD等对熔覆层的微观组织进行了分析,测试了熔覆层的显微硬度和摩擦磨损性能。结果表明,激光熔覆层与基体形成了良好的冶金结合,熔覆层的组织主要由γ-Ni,Cr7C3和CrB等相组成。熔覆层显微硬度在650~850HV之间,明显高于H13钢基体的硬度。摩擦磨损实验表明,在相同的条件下,熔覆层的耐磨性比基体有了明显的提高,磨损体积减少了92.4%。通过对磨损后的试样进行粗糙度测试后表明,涂层具有更平滑的表面。  相似文献   

3.
钛合金表面激光熔覆TiC_p/Ni基合金复合耐磨涂层   总被引:8,自引:2,他引:6  
采用激光熔覆技术在TC4合金表面制备TiC颗粒增强的Ni基合金复合材料涂层,测试了熔覆层的硬度和滑动摩擦磨损性能,分析了熔覆层的强化机制。结果表明,熔覆层中存在颗粒强化、固溶强化和细晶强化等多种强化作用,熔覆层的显微硬度达HV900~1100,耐磨性能比TC4合金显著提高。  相似文献   

4.
为了解决Cr12MoV钢溶蚀、表面碎裂等问题,利用Al-Ni、Nd-Ni粉末在Cr12MoV钢上进行激光熔覆实验,研究了Al、Nd对镍基覆层的宏微观形貌、组织及表面性能的影响。结果表明:Al可以减少熔覆层裂纹的产生,同时降低覆层硬度,使熔覆层中产生具有减磨作用的硬质相Al2O3等,降低覆层磨损量,14%Al覆层磨损量比2%Al的覆层磨损量低44.5%,Al较优质量分数为14%;Nd的晶粒细化作用明显,显著提升覆层显微硬度,2.5%Nd覆层平均硬度比基体平均硬度高36.8%,Nd较优质量分数为2.5%。  相似文献   

5.
采用激光熔覆技术在斜齿轮钢表面制备Fe基熔覆层。通过光学显微镜、显微硬度计对熔覆层进行金相组织与显微硬度分析,采用磨损机对熔覆层和基材进行摩擦实验。结果表明:当激光功率为750W,送粉速率为20g/min,扫描速度10mm/s,离焦量为16.4mm时,铁基熔覆层与基体结合界面有明显的白亮带,激光熔覆效果较好,熔覆层的显微硬度值分布在845.3HV至955.6HV之间,约为基体硬度(419.7HV)2倍;熔覆层摩擦磨损性能得到了提高;熔覆层显微组织为均匀而细小的铁素体和珠光体,力学性能优于基体材质。  相似文献   

6.
利用光学显微镜和扫描电镜观察了钛合金表面TiC-Ni激光熔覆层的宏观形貌和微观组织,测试了激光熔覆层的硬度、摩擦系数和磨损量。利用SEM观察了磨损的表面形貌和磨屑的形貌,分析了激光熔覆层的磨损机制。结果表明:激光熔覆层组织致密,无气孔和裂纹,硬度为基材的3倍;激光熔覆层的摩擦系数随环境压力的降低而提高,磨损量随环境压力的降低、法向载荷的增加而增加;低载时为轻微的磨粒磨损,高载时为严重的剥层磨损。  相似文献   

7.
在Cr12MoV模具钢表面进行了激光熔覆试验,探讨了工艺参数对熔覆层深度影响、显微硬度和合金元素分布、表面耐磨性能的变化的趋势,为激光重熔技术的应用提供依据。  相似文献   

8.
TG156.99 2006032065激光熔覆TiC陶瓷涂层的组织和摩擦磨损性能研究=Mi-crostructure and friction wear properties of TiC laser cladlayer[刊,中]/孙荣禄(天津工业大学机械电子学院.天津(300160)) ,杨贤金∥光学技术.—2006 ,32(2) .—287-289采用激光熔覆技术在TC4合金表面上制备了TiC陶瓷涂层,分析了熔覆层的微观组织,测试了熔覆层的硬度和摩擦磨损性能。结果表明,TiC激光熔覆层分为熔覆区和稀释区两个区域,熔覆区未受到基底的稀释,由TiC颗粒和TiC树枝晶组成;稀释区受到了基底的稀释,由TiC树枝晶和钛合金组成;TiC激光熔覆层的…  相似文献   

9.
采用激光熔覆技术在45钢基体上制备了不同CeO2含量的镍基纳米Al2O3复合涂层,对熔覆层进行了微观组织分析和显微硬度测试。结果表明,随着CeO2含量的增加,熔覆层组织由亚共晶向共晶组织转变;加入1.0%CeO2对镍基纳米Al2O3熔覆层的组织起到明显的细化和净化作用,枝晶生长的方向性减弱,组织趋向均匀,熔覆涂层的显微硬度值比未加稀土的涂层提高了60-95HV0.2。  相似文献   

10.
为研究激光冲击对E690高强钢激光熔覆修复层微观组织的影响,选用专用金属粉末对E690高强钢试样预制凹坑进行激光熔覆修复,并使用脉冲激光对激光熔覆层进行冲击强化处理,同时采用扫描电镜、透射电镜和X射线应力分析仪分别对激光冲击前后激光熔覆层的微观组织和表面残余应力进行检测。结果表明:激光熔覆修复后,激光熔覆层组织为等轴晶,熔覆层与E690高强钢基体之间冶金结合良好,其表面残余应力为均匀分布的压应力。经激光冲击后,激光熔覆层截面晶粒得到细化,并观察到大量的形变孪晶,互相平行的孪晶界分割熔覆层粗大晶粒,在激光熔覆层的晶粒细化过程中发挥着重要作用;试样表层位错在{110}滑移面上发生交滑移,在晶界周围形成了位错缠结。经激光冲击后,激光熔覆层冲击区域表面残余压应力数值相较于冲击前提升了1.1倍。  相似文献   

11.
The effects of wire feeding direction and position, cladding time, and cladding speed on the quality of cladding layer for laser cladding with wire feeding are studied. Experiment results indicate that the wire feeding direction and position are important for wire laser cladding. By adopting the correct wire feeding direction and position, the wire can be plunged into the melt pool and can be melted by the heat of the molten metal. With the increase of cladding speed, the dilution of clad layer can be reduced and the growth of the grain size of heat-affected zone of the base metal can be limited. If proper cladding parameters are used, the clad layers will have a good surface shape, sound metallurgical bonding with base metal, low dilution, and the effect of heating on heat-affected zone metal can be limited. The hardness of the clad layer and heat-affected zone are checked. It indicates that with the increase of cladding speed, the hardness of the clad layer and heat-affected zone increases.  相似文献   

12.
Coaxial laser cladding on an inclined substrate   总被引:7,自引:0,他引:7  
This paper describes an experimental and theoretical study of the cladding mode of coaxial laser cladding on an inclined substrate. Based on the image analysis of the powder stream and clad profile measurements in coaxial laser cladding, it was found that irregular clad profiles always formed on an inclined surface and the location of the peak profile shifted away from the clad center. This phenomenon is caused by uneven distributions of powder concentration and laser beam intensity. A modified Gaussian mode for powder stream and laser beam was proposed to estimate the clad profiles on an inclined plane under laser beam irradiation. The effects of the inclined steel substrate on the CO2 laser beam absorption and stainless-steel powder catchment were examined experimentally. The results show that both the laser absorption and the powder catchment on the mild steel decrease with increasing the cladding angle. From the analysis of laser beam mode, the clad width is equivalent to the beam spot size on the inclined substrate. However, the clad height correlates well with the distribution of the powder concentration. The results show that the Gaussian cladding mode could be adopted in various laser cladding applications such as rapid prototyping and butt welding to predict the clad profiles precisely.  相似文献   

13.
This paper presents in-time motion adjustment in laser cladding manufacturing process as a means to improve dimensional accuracy and surface finish of the built part. Defects occurring during laser cladding degrade the part quality such as dimensional accuracy and surface finish. In this paper, in-time motion adjustment strategy was presented to remedy and eliminate defects occurring during laser cladding to improve the dimensional accuracy and surface finish. Based on the relationship between the motion of laser head relative to the growing part and other parameters in effects on clad profile, the laser traverse speed, stand-off distance and laser approach orientation to the existing clad layer were adjusted by instructions from a close-loop control system in real time to remedy and eliminate defects. The results of the experiments verified the effects of in-time motion adjustment on dimensional accuracy and surface finish.  相似文献   

14.
铁基合金激光熔覆层高温润滑磨损性能   总被引:3,自引:3,他引:0       下载免费PDF全文
 为提高40Cr合金钢的表面耐磨性,采用预置激光熔覆法在40Cr基体表面制备铁基合金涂层, 利用扫描电镜观察分析熔覆层显微组织形貌,用显微硬度仪测试熔覆层截面显微硬度,用摩擦磨损试验机测定在润滑条件下基体、熔覆层的摩擦系数随温度变化的规律。研究结果表明:熔覆层与基体实现良好冶金结合,熔覆层横截面微观组织呈现平面晶、树枝晶和胞状晶分布;熔覆层硬度值介于617.5~926.6 HV0.2之间,基体硬度介于205.2~278.2 HV0.2之间;在200 ℃以下,熔覆层摩擦系数在磨程中趋于平稳,在0.1附近轻微波动,小于基体平均摩擦系数;当温度超过200 ℃,油膜分解,引发润滑失效,磨损方式向干摩擦转化,磨损机理从微切削磨损主导向粘着磨损、磨粒磨损和氧化磨损复合磨损方式转化。  相似文献   

15.
The effect of coatings, which are formed with laser cladding and plasma spray welding on 1Cr18Ni9Ti base metal, on wear resistance is studied, A 5-kW transverse flowing CO2 laser is used for cladding Co base alloy powder pre-placed on the substrate. Comparing with the plasma spray coatings, the spoiled rate of products with laser clad layers was lower and the rate of finished products was higher. Their microstructure is extremely fine. They have close texture and small size grain. Their dilution resulting from the compositions of the base metal and thermal effect on base metal are less. The hardness, toughness,and strength of the laser cladding layers are higher. Wear tests show that the laser layers have higher properties of anti-friction, anti-scour and high-temperature sliding strike. The wear resistance of laser clad layers are about one time higher than that of plasma spray welding layer.  相似文献   

16.
In order to determine a cross-sectional profile of a clad bead in coaxial laser cladding, its formation mechanism is investigated theoretically and experimentally. In laser cladding, every point at the back edge of a melt pool is contributed to a cross-sectional profile of the clad bead to be formed, and points at the same pool edge but on different cross sections are located at different cross-sectional profiles of the clad bead. A cross-sectional profile of a clad bead is composed of points of intersection between the cross section and a series of pool edges. Model of the cross-sectional clad profile in single-pass coaxial laser cladding is developed. A 500 W CO2 laser is used in the experiment. The experimental result agrees well with the calculated cross-sectional clad profile.  相似文献   

17.
Based on the powder feeding laser induction hybrid cladding experiments by means of three different laser and induction energy, the microstructure of Ni-based coating and interface characteristics between the Ni-based coating and steel substrate were investigated. The results show that the hybrid cladding energy including laser and induction energy has an important influence on the formation of the interface and the microstructure of the Ni-based coating characterized by the dendrite. In addition, the laser and induction energy can complement each other. For high hybrid cladding energy, the single phase Fe-Ni-Cr solid solution is formed at the interface between the coating and substrate, while the microhardness of the Ni-based coating decreases. For low hybrid cladding energy, the solid solution phases of Fe-Ni-Cr and Ni-Fe-Cr are respectively obtained on both sides of the interface and microhardness of the Ni-based coating is relatively high. During laser induction hybrid cladding, the metallurgical bond characterized by the white light layer is achieved between the coating and substrate, and the extent of metallurgical reaction can be controlled by adjusting the laser energy and induction energy appropriately.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号