Evolution of the phase composition and physicomechanical properties of ZrO<Subscript>2</Subscript> + 4 mol % Y<Subscript>2</Subscript>O<Subscript>3</Subscript> ceramics

The evolution of the phase composition and physicomechanical properties of ZrO₂ + 4 mol % Y₂O₃ ceramics subjected to hot isostatic pressing and subsequent calcining in air is investigated. It is found that hot isostatic pressing results in the formation of an easily transformed phase T_et with a degree of tetragonality c/a=1.035, which determines high fracture toughness. After calcining in air, the phase T_et decomposes to form a nontransformed phase T′ with a degree of tetragonality c/a=1.005, which determines low fracture toughness.     

Properties of hot pressed MgB2/Ti tapes

Hot axial and hot isostatic pressing was applied for single-core MgB₂/Ti tapes. Differences in transport current density, n-exponents and critical current anisotropy are discussed and related to the grain connectivity influenced by pressing. The magnetic Hall probe scanning measurements allowed observing the isolated regions for axially hot pressed sample attributed to the longitudinally oriented cracks introduced by pressing. The highest current densities were measured for the tape subjected to hot isostatic pressing due to improved connectivity.     

Elasticity and anelasticity of microcrystalline aluminum samples having various deformation and thermal histories

The effect of the amplitude of vibrational deformation on the elastic modulus and internal friction of microcrystalline aluminum samples produced by equal-channel angular pressing was studied. The samples have various deformation and thermal histories. The elastic and inelastic (microplastic) properties of the samples are investigated. As the degree of plastic deformation increases, the Young’s modulus E, the amplitude-independent decrement δ_i, and the microplastic flow stress σ increase. As the annealing temperature increases, the quantities δ_i and σ decrease noticeably and the modulus E exhibits a more complex behavior. The experimental data are discussed under the assumption that the dislocation mobility depends on both the spectrum of point defects and the internal stresses, whose level is determined by the degree of plastic deformation and the temperature of subsequent annealing. The concept of internal stresses is also used to analyze the data on the effect of the degree of deformation and annealing on the rupture strength of the samples.     

Internal friction in silver-containing (Ag3AsS3) x (As2S3)100 ? x superionic glasses

The mechanical properties of glasses in the Ag₃AsS₃-As₂S₃ system have been studied by the internal friction method. Measurements of internal friction and shear modulus have been carried out in the temperature interval 80?C300 K at deformation frequencies of 10?C50 mHz. Relaxation-type maxima of internal friction have been revealed. It has been shown that the concentration-induced variations in the parameters of the mechanical relaxation process in (Ag₃AsS₃) _x (As₂S₃)_{100 ? x} glasses observed in the region of 20 at % Ag₃AsS₃ are of the threshold character. It has been established that this feature can be associated with the variation in the structural unit, which accounts for the process of mechanical energy dissipation within the temperature interval 150?C250 K.     

Low-frequency internal friction of polycrystalline ZrO2-4 mol % Y2O3 in the temperature range 273–373 K

The specific features in the low-frequency internal friction, structure, and phase composition of polycrystalline ZrO₂-4 mol % Y₂O₃ are investigated in the temperature range 273–373 K. It is demonstrated that the low-frequency internal friction exhibits two peaks upon heating and cooling. The former peak is observed at a temperature of approximately 293 K, and the latter peak is revealed at 313 K. It is assumed that the peak observed in the low-frequency internal friction at a temperature of 293 K is attributed to relaxation dissipation of energy during motion of twin boundaries in the monoclinic phase, whereas the peak at 313 K is associated with relaxation processes due to displacement of the boundaries of tetragonal T′ domains.     

Elasticity and inelasticity of silicon nitride/boron nitride fibrous monoliths

A study is reported on the effect of temperature and elastic vibration amplitude on Young’s modulus E and internal friction in Si₃N₄ and BN ceramic samples and Si₃N₄/BN monoliths obtained by hot pressing of BN-coated Si₃N₄ fibers. The fibers were arranged along, across, or both along and across the specimen axis. The E measurements were carried out under thermal cycling within the 20–600°C range. It was found that high-modulus silicon-nitride specimens possess a high thermal stability; the E(T) dependences obtained under heating and cooling coincide well with one another. The low-modulus BN ceramic exhibits a considerable hysteresis, thus indicating evolution of the defect structure under the action of thermoelastic (internal) stresses. Monoliths demonstrate a qualitatively similar behavior (with hysteresis). This behavior of the elastic modulus is possible under microplastic deformation initiated by internal stresses. The presence of microplastic shear in all the materials studied is supported by the character of the amplitude dependences of internal friction and the Young’s modulus. The experimental data obtained are discussed in terms of a model in which the temperature dependences of the elastic modulus and their features are accounted for by both microplastic deformation and nonlinear lattice-atom vibrations, which depend on internal stresses.     

Effect of gamma irradiation on internal friction in lithium tetraborate

The effect of gamma irradiation on the mechanical properties of lithium tetraborate Li₂B₄O₇ in the single-crystal and vitreous states is investigated. It is found that, after irradiation of the Li₂B₄O₇ single crystal, the temperature range of the dissipative process initially occurring at 380–420 K becomes broader and the fine structure of the peak in the temperature dependence of the internal friction Q^?1(T) undergoes a substantial trans-formation. After irradiation of the vitreous Li₂B₄O₇ sample, the increase in the internal friction, which is characteristic of the onset of the α relaxation in this material, is not observed in the dependence Q^?1(T) up to a temperature of 570 K. It is shown that the mechanical properties of the irradiated samples are almost completely recovered after annealing at 570 K for 1 h.     

A mechanical spectrum study of bilayer cuprate La1.82Sr0.18CaCu2O6+δ

The mechanical spectrum of bilayer cuprate La_1.82Sr_0.18CaCu₂O_6+δ (La2126) was measured using the vibrating reed method from 30 K to room temperature at kilohertz frequency. A clear modulus softening was observed at 223 K accompanied by a sharp internal friction peak, which evidences a phase transition. Another broad internal friction peak around 250 K was observed, accompanied by a large modulus change. This contrasts with the broad internal friction peak of Ca doped Y Ba₂Cu₃O_7−δ (Y123) for which no clear modulus change was observed. The main contribution to the broad internal friction peak of La2126 is expected to be from the glass transition of the interstitial oxygen atoms.     

GdBaCo2O5+δ体系的滞弹性内耗研究

GdBaCo₂O_5+δ体系的低频内耗研究表明：体系中存在一个由额外氧运动引起的弛豫内耗峰；额外氧δ对这个弛豫内耗峰的大小、峰形及峰位有较大影响，反映了额外氧状态随δ而变化.当δ=0.005，体系中额外氧含量很少而接近零时，相应的内耗峰消失；δ达到一定数量后，出现弛豫内耗峰.由δ=0.278，0.407，0.421，0.515样品的弛豫内耗峰分析可得到体系随δ不同存在着三种不同的额外氧形态.此外，δ=0.421及0.515的样品在360K附近存在一个相变内耗峰，它对应着体系中的金属—绝缘体转变. 关键词： 2O_5+δ')" href="#">GdBaCo₂O_5+δ 额外氧 内耗峰     

Phase transformations induced by mechanical stresses in powders of oxide solid solutions

The influence of cold isostatic pressing to 2.0 GPa on the phase transformations in powders of ZrO₂-Y₂O₃ solid solutions and γ-Al₂O₃ is investigated. The cold isostatic pressing of ZrO₂-Y₂O₃ is shown to lead to conversion of the tetragonal modification into a monoclinic phase. The extent of conversion decreases as the Y₂O₃ content and the particle size increase. In the case of γ-Al₂O₃ powders, cold isostatic pressing at 1.5 GPa leads to lowering of the temperature at which the aphase appears by 100 K in comparison to a γ-Al₂O₃ powder subjected to cold isostatic pressing at 0.1 GPa. A quantitative model, which accounts for the experimental results discovered, is proposed. Zh. Tekh. Fiz. 69, 27–31 (February 1999)     

Singularities of magnetic and elastic characteristics of La2/3Ba1/3MnO3: Analysis of martensitic kinetics

A coordinated temperature behavior of magnetic susceptibility and internal friction has been observed in the La_2/3Ba_1/3MnO₃ manganite in the temperature region of the crystal phase separation 5–340 K. Stepwise temperature behavior of the susceptibility of the single crystal sample and corresponding singular behavior of the internal friction in the polycrystalline manganite have been found. These small-scale features of the temperature dependences of the susceptibility and the internal friction are considered to be a reflection of martensitic kinetics of the structural phase transformation R3¯c↔Imma in the 200 K temperature region.     

A low temperature internal friction study of Y0.85Ca0.15Ba2Cu3O7−δ with different oxygen content

The ceramic sample of Y_0.85Ca_0.15Ba₂Cu₃O_7−δ was prepared by standard solid-state reaction method, and samples with different oxygen concentration were obtained by quenching from high temperature. The internal friction was measured using the vibrating reed method from liquid-nitrogen temperature to room temperature at kilohertz frequency. An internal friction peak was observed around 250 K in Y_0.85Ca_0.15Ba₂Cu₃O_7−δ quenched from 1023 K. The peak is related to the one observed around 220 K (labeled as P3 peak) in undoped YBa₂Cu₃O_7−δ (Y123). This result shows the dependence of P3 peak on carriers density and P3 peak has a strong correlation to the abnormal behavior of Y123 in the underdoped range. The variation of two low temperature thermal activated relaxation peaks (P1 and P2) on oxygen content were also investigated. And consistent explanations were given based on all recent researches.     

Internal friction in Cu6PS5Br superionic crystals and related composites

Mechanical properties of Cu₆PS₅Br single crystals and composites based on them have been investigated by the internal friction method. The measurements of the internal friction and the shear modulus have been performed in the temperature range of 80–300 K at deformation frequencies of 10–100 mHz in a mode of forced torsional vibrations. The maxima caused by the superionic and ferroelastic phase transitions have been found in temperature dependences of the internal friction. It has been shown that a more than two-fold decrease in the shear modulus with increasing temperature in the range of 150–230 K is caused by mobility unfreezing in the cation sublattice of the Cu₆PS₅Br single crystal during the superionic phase transition. An abrupt (more than threefold) increase in the shear modulus upon heating in the range of 260–270 K is caused by the ferroelastic phase transition of the Cu₆PS₅Br single crystal. Parameters of the internal friction of this single crystal in the course of mentioned phase transitions have been determined.     

Synthesis, structural and transport properties of nanocrystalline La1−xBaxMnO3 (0.0≤x≤0.3) powders

Nanocrystalline La_1−xBa_xMnO₃ (0.0≤x≤0.3) manganites have been prepared by a simple and instantaneous solution combustion method, which is a low temperature initiated synthetic route to obtain fine-grained powders with relatively high surface area. The phase purity and crystal structure of the combustion products are carried out by powder X-ray diffraction. The as-made nanopowders are in cubic phase. On calcination to 900 °C, barium doped manganites retain cubic phase, whereas barium free manganite transformed to rhombohedral phase. The scanning electron microscope (SEM) results revealed that the combustion-derived compounds are agglomerated with fine primary particles. The doped manganites have surface area in the range 24-44 m²/g. The surface area of the manganites increases with barium content, whereas it decreases on calcination. Both undoped and doped lanthanum manganites show two active IR vibrational modes at 400 and 600 cm⁻¹. The low temperature resistivity measurements have been carried out by four-probe method down to 77 K. All the samples exhibit metal-insulator behaviour and metal-insulator transition temperature (T_M-I) in the range 184-228 K and it is interesting to note that, as the barium content increases the T_M-I shifts to lower temperature side. The maximum T_M-I of 228 K is observed for La_0.9Ba_0.1MnO₃ sample.     

Structural-phase state of chromium-fullerite-chromium films subjected to heat treatment in vacuum

The patterns of change in the structure and the phase composition of chromium-fullerite-chromium films subjected to heat treatment in vacuum at different temperatures (470, 570, and 620 K) are studied via scanning electron and atomic force microscopies, X-ray diffraction, reflection-electron diffraction, and X-ray spectral microanalysis. It is found that sample annealing at 470 and 570 K leads to recrystallization of the fullerite and the emergence and growth of a new Cr _x C₆₀ phase, accompanied by volumetric changes that generate internal mechanical stresses. During the process of stress relaxation, the film starts to crack, and lamellar crystallites of the fullerite phase start to grow. Film destruction and the growth of C₆₀ crystallites on the surface are not observed in chromium-fullerite-chromium films annealed at 620 K.     

Thermoelectric properties of p‐type Mg2Si0.6Ge0.4 fabricated by bulk mechanical alloying and hot pressing

Bulk mechanical alloying (BMA) followed by hot pressing (HP) was used to prepare Mg₂Si_0.6Ge_0.4 thermoelectric material with high densification. Starting from the elemental power mixture, the Mg₂Si_0.6Ge_0.4 solid solution was solid‐state synthesized via BMA. In fact, the peaks for the cubic‐structured Mg₂Si_0.6Ge_0.4 solid solution phase were detected after 300 cycles in BMA. The single phase of Mg₂Si_0.6Ge_0.4 was synthesized at 600 cycles in BMA. Mg₂Si_0.6Ge_0.4 showed p‐type semiconduction without doping. Effects of hot pressing conditions on thermoelectric properties were investigated. With increasing hot pressing temperature from 673 to 773 K and pressure from 500 MPa to 1 GPa, the electrical conductivity increased and the Seebeck coefficient decreased. The maximum figure of merit was obtained with the processing parameter of 600 cycles BMA and hot pressing at 773 K, 1 GPa for 1 h. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Phase transitions in La0.5Sr0.5FeO3−δ investigated by mechanical spectrum

The mechanical spectrum measurement was performed in ceramic La_0.5Sr_0.5FeO_3?δ from liquid nitrogen temperature to room temperature at kilohertz frequencies. From temperature dependent reduced modulus, a kink (corresponding temperature labeled as T_M) was observed which evidenced a phase transition by the mechanical spectrum at two flexural resonance frequencies. This elastic manifested phase transition is a charge disproportionation transition. Around 170 K, an internal friction peak (labeled as P1) was observed accompanied with a large modulus hardening with the decrease in temperature. Two mechanisms are proposed for P1 peak, one is elastic manifestation of magnetic freezing, and the other is the ordering or freezing of oxygen vacancies.     

Comparative study of the magnetic and electrical properties of Pr1−xBaxMnO3−δ manganites depending on the preparation conditions

Magnetization, electrical resistivity and magnetoresistance of Pr_0.50Ba_0.50MnO_3−δ manganites with perovskite structure have been investigated as a function of preparation conditions. It was found that the as-prepared samples (prepared in air) show T_C=110 K (first order phase transition), whereas for those annealed in flowing argon the T_C value increases up to 340 K without change of cubic symmetry (second order phase transition). Ferromagnet–paramagnet transition is accompanied by both a metal–insulator transition and a magnetoresistance peak. The X-ray study has revealed that the samples annealed in argon have broad peaks apparently due to microstrains and crystal structure defects. The argon-treated samples improve the magnetization after subsequent annealing in air at T⩽1000°C. T_C of argon-treated samples is stable with respect to annealing in air up to 1300°C where it becomes again 110 K. In contrast, a treatment in vacuum destroys the ferromagnetic order. Auger-spectroscopy has not revealed any additional ions except Pr, Ba, Mn and O for all the samples. External pressure enhances the Curie point of the sample prepared in air at a rate of 43 K/GPa. We have observed that the samples Pr_1−xBa_xMnO_3−δ, x⩾0.30, exhibited the above-mentioned effect of increasing T_C after treatment in flowing argon without changes of the phase state, whereas the samples x<0.30 decomposed into different phases. The dramatic increase of T_C after argon treatment is supposed to result from microstrains and crystal structure defects in the sample.     

In situ Raman spectroscopy of phase transformation in CrOx-Y2O3 system at elevated temperatures

A CrO_x-Y₂O₃ sample was prepared by a deposition-precipitation method and phase transformation of the sample under N₂ and air atmospheres was characterized by in situ Raman spectroscopy and X-ray diffraction (XRD) techniques. It was found that when the CrO_x-Y₂O₃ sample was heated, CrO₃ transformed to YCrO₄ and then to YCrO₃ and Cr₂O₃. Also, the transformation started from the surface region of the sample and then extended to the bulk, due to the fact that the phase transformation was detected by Raman spectroscopy at lower temperature compared to that by XRD. In addition, both atmosphere and temperature had influence on the phase transformation in the surface region, while the phase transformation in the bulk was merely dependent on the temperature. It was also found that low oxidation state Cr(III) species on the surface could be re-oxidized to high oxidation state Cr(V) or Cr(VI) species when the thermal treated sample was exposed to ambient air.     

Elastic properties of La<Subscript>0.82</Subscript>Ca<Subscript>0.18</Subscript>MnO<Subscript>3</Subscript> single crystal

The temperature dependences of the velocity of longitudinal sound waves and the internal friction in a La_0.82Ca_0.18MnO₃ single crystal with the Curie temperature T _C = 181 K have been studied. As temperature decreases, the single crystal is shown to undergo the transition from the pseudocubic O* to the Jahn–Teller O’ phase at T ~ 254 K and the reverse transition from O’ to O* phase at T ~ 84 K. The velocity of sound and the internal friction in the O’ phase are found to be significantly smaller than those in the O* phase.