新型表面波电流传感器优化设计

本文对结合磁致伸缩效应的新型声表面波电流传感器进行优化设计。传感器采用80 MHz声表面波双通道延迟线型差分振荡器,并在传感通道SAW器件表面声传播路径上溅射磁致伸缩薄膜,利用薄膜材料在电流激发磁场作用产生的磁致伸缩效应引起声传播速度的变化,并以相应振荡器频率的变化来表征待测电流。通过对不同磁致伸缩材料(FeCo和FeNi)以及薄膜厚度的传感效应进行分析,用以为传感器的优化设计提供思路,并通过实验进行验证,实验结果显示,相对于FeCo而言,采用FeNi作为敏感材料的电流传感器具有良好的重现性、线性度以及较高的灵敏度。     

压电免疫传感器的设计及应用

压电免疫传感器作为一种新型生物传感器,是利用压电元件的质量敏感性质,结合生物免疫识别特性而形成的一种自动化分析检测传感器,它可对钦种抗原或抗体进行的定量测定,并可有于反应动力学的研究,具有高特异性、高灵敏度、响应快、小型简便等特点。本文利用石英晶体产生体波厚度剪切振动模式,由双通道系统进行频率变化的测定。采用氨基硅烷膜固定抗体来定量检测溶液中人体免疫球蛋白Ｉdisplay status     

声表面波梁式加速度传感器的优化设计

为获得传感器的优化设计,对一种声表面波梁式加速度传感器敏感机理进行了研究。从声波波动方程出发,结合有限元分析以及微扰理论对加速度作用力作用下声表面波传播特性进行分析,以此构建梁式声表面波加速度传感器敏感机理的理论模型,特别分析了压电梁材料及几何结构、振子质量对传感响应的贡献以确定传感器优化的几何参数。为验证理论分析结果,实验研制了基于ST-X石英悬臂梁结构的差分振荡式声表面波加速度传感器,并利用精密振动台对所研制传感器性能进行评价。实验结果显示,在给定加速度测试范围内,采用ST-X石英梁并延长梁长度、降低梁厚度以及采用较大的阵子质量将有效的改善传感器检测灵敏度,在±2 g范围内加速度灵敏度可达27 k Hz/g,且实验结果很好的验证了理论模型。     

一种高灵敏度的桥型声表面波应变传感器*

为了提高声表面波传感器应变灵敏度,该文提出了一种桥型声表面波应变传感器。首先根据受压弯曲构件中应变分布特点设计了桥型声表面波应变传感器,并建立有限元模型,结合微扰法分析了桥型结构几何参数与声表面波应变传感器灵敏度的关系。根据分析结果确定桥型声表面波应变传感器几何结构参数,并与传统声表面波应变传感器的应变灵敏度进行了对比研究,在此基础上搭建受压弯曲微动平台开展实验研究,结果表明:在直梁构件受压弯曲应变测量时,Y34°切向的桥型声表面波应变传感器的应变灵敏度为1692 Hz/με,传统声表面波传感器应变灵敏度为1328 Hz/με,桥型声表面波应变传感器的应变灵敏度较传统声表面波应变传感器有明显提高。     

由于表面粗糙引起的激光声表面波色散的实验和理论研究

表面粗糙是材料制造过程中必有的副产物, 粗糙表面会引起其中传播的声表面波的速度发生变化. 在利用激光声表面波对材料性质进行评估时, 常用宽带的激光声表面波速度频散特性对材料性质进行反演. 为了研究表面粗糙度是否能作为反演的特征参数之一, 本文建立了激光在表面粗糙样品中激发声表面波、聚偏氟乙烯换能器宽带接收声表面波的实验装置来研究不同粗糙度表面对声表面波速度的影响; 理论上建立了激光在粗糙表面中激发声表面波的计算模型, 利用有限元法得到声表面波的时域特征, 并进一步得到声表面波的速度色散曲线, 理论结果和实验结果能很好地拟合. 这为利用激光声表面波对表面粗糙的评估提供理论和实验依据. 关键词： 表面粗糙 激光声表面波 速度色散 聚偏氟乙烯传感器 有限元法     

基于指条厚度优化的冷凝式SAW气体传感器灵敏度提升方法

该文通过对声表面波谐振器指条厚度的优化提升了冷凝式气体传感器的灵敏度。基于流固耦合理论,利用有限元商业软件建立了有液膜负载和无液膜负载下的多物理场三维周期模型,并提取了相应的耦合模参量,利用耦合模模型及P矩阵级联技术,计算了不同指条厚度下液膜负载引起的传感器响应,获得了冷凝式声表面波气体传感器灵敏度随指条厚度的变化关系。实验中制备了6种不同电极厚度的声表面波谐振器,并利用甲基膦酸二甲酯实验样品完成了传感器的响应测试,验证了理论分析的正确性。结果表明,冷凝式声表面波气体传感器的灵敏度随指条厚度的增加先变大后减小,最优归一化电极厚度为6.4%～7.6%之间。该研究结果对进一步提升传感器灵敏度具有重要意义。     

谐振式检测器指条厚度对质量型声表面波传感器灵敏度的影响

研究了谐振器指条厚度对质量型声表面波传感器灵敏度的影响.利用耦合模方程推导出耦合模参量与周期栅阵禁带边界频率的关系,结合有限元及P矩阵模型,获得了声表面波传感器灵敏度随指条厚度的变化关系。制备3种不同铝指条厚度(1600?,1900?,3100?)的声表面波谐振器,通过对其表面中心区域沉积SiO_2层验证了计算结果。结果表明:采用ST-X石英基底的声表面波谐振器对SiO_2负载检测时,传感器的灵敏度随铝指条厚度的增加先变大后减小,最优归一化指条厚度为1.9%。分析表明,指条厚度对传感器灵敏度的影响主要来自于传播速度和耦合系数的共同作用,通过优化指条厚度的方法可改善传感器的灵敏度.     

用于电流传感的声表面波磁致伸缩效应

利用声表面波(SAW)磁致伸缩效应可以实现一种快速、高灵敏度的电流检测方法,但磁致伸缩薄膜内部矫顽力导致了明显的磁滞误差。磁致伸缩薄膜的栅阵化设计可以减小磁致伸缩时薄膜内部矫顽力,抑制磁滞现象,从而实现高灵敏和低迟滞误差的SAW电流检测。结合有限元和耦合模理论对沉积铁钴(FeCo)薄膜栅阵的声表面波电流传感器中的磁致伸缩效应进行分析,对传感响应进行仿真,确定优化的传感结构参数。为验证理论分析,实验研制了频率为150 MHz的声表面波电流传感器件,并结合差分振荡电路及亥姆霍兹线圈,建立传感器测试系统.实验结果表明,磁致伸缩薄膜的栅阵设计大幅降低了迟滞误差,并显著提升了传感器灵敏度。      

声表面波介质表面受力条件下的波速变化研究

为了计算力负载直接作用在声表面波传播表面时波速的变化特性,通过有效材料系数将负载引入,并用广义Green函数计算声速,得到了数值计算的结果,并用声表面波谐振器进行了实验.实验结果表明,将力负载直接加载在声表面波的传播表面时,波速变化量和力负载大小近似为线性关系,该加载方式下,实验中声表面波谐振器的谐振频率对外加质量负载有较高的灵敏度,可达1900 Hz/g.     

可实现防碰撞通信的新型声表面波温度传感器

针对多声表面波传感器系统中各传感器信息读取时会产生通信碰撞的问题,提出了一种可实现防碰撞通信的新型声表面波温度传感器;通过分析声表面波温度传感器的回波脉冲信号,将沃尔什码作为编码内容实现了多声表面波温度传感器系统中各传感器的正交编码;将传感器对应的匹配信号与系统回波信号进行互相关运算,提取了系统中各传感器的感测温度信息,达到了防碰撞通信的目标;该传感器兼顾编码效率和加工工艺两方面要求,简化感测信息提取的复杂程度;仿真实验验证了上述理论的正确性。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.