Ternary semiconductor compounds CuInS2 (CIS) thin films synthesized by electrochemical atomic layer deposition (EC-ALD)

In this paper the formation and characterization of the I-III-VI₂ semiconductor compound CuInS₂ (CIS) on gold substrate at room temperature by electrochemical atomic layer deposition (EC-ALD) method are reported. Optimum deposition potentials for each element are determined using cyclic voltammetry (CV) technique and Amperometric I-t method is used to prepare the semiconductor compound. These thin films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FE-SEM) and Fourier transform infrared spectroscopy (FT-IR). XRD results indicate that the CIS thin films have a (1 1 2) preferred orientation. The XPS analyses of the films reveal that Cu, In and S are present in an atomic ratio of approximately 1:1:2. And their semiconductor band gaps are found to be 1.50 eV by FT-IR.     

Surface characteristics and nanoindentation study of Ni-Mn-Ga ferromagnetic shape memory sputtered thin films

In present paper, the off-stoichiometric Ni-Mn-Ga ferromagnetic shape memory alloy thin films are fabricated using radio frequency magnetron sputtering method. The compositions, microstructures and mechanical properties of the thin films are characterized by energy dispersive X-ray spectrum (EDAX), X-ray photoelectron spectroscopy (XPS), scanning electronic microscope (SEM), atomic force microscope (AFM) and nanoindentation test, respectively. The results show that there is a thinner layer of oxides consisting of NiO, Ga₂O₃ and an unspecified manganese oxidation (Mn_xO_y) at the surface, whereas a small amount of MnO precipitates exist in internal layers of post-annealed Ni-Mn-Ga thin films. The hardness and elastic modulus decrease with increasing film thickness. Nanoindentation tests reveal that the hardness and elastic modulus of the films can be up to 5.5 and 155 GPa, respectively. The Ni-Mn-Ga thin films have remarkably improved the ductility of Ni-Mn-Ga ferromagnetic shape memory alloys bulk materials.     

Preparation and transmission loss of the nano-crystal and polymer composite film BTO/PMMA

Bismuth titanate, Bi₄Ti₃O₁₂ (BTO), is a typical ferroelectric material with useful properties for optical memory, piezoelectric and electro-optic devices. Its nano-crystals were compounded by the chemical solution decomposition technique. The structure and size of BTO were analyzed by X-ray diffraction and transmissive electron microscopy. Two sorts of composite films BTO/polymethylmethacrylate with different weight ratio of BTO were prepared by spin-coating method at certain conditions. In this article, the scattering loss in thin films was obtained using an imaging technique.     

Nanostructured TiO<Subscript>2</Subscript> Films with a Mixed Phase for Perovskite Solar Cells

A series of thin films made with TiO₂ nanoparticles with a varied anatase/rutile phase ratio is prepared on conducting glass substrates using a spin-coating method. The structure, morphology, and optical properties of TiO₂ nanopowders and thin films fabricated are studied using powder X-ray diffraction, scanning electron microscopy, and optical spectroscopy. The TiO₂ nanostructured films created are used as photoelectrodes for the fabrication of perovskite solar cells (PSCs). The photovoltaic characteristics of PSCs under AM1.5 light illumination (1000 W/m²) under ambient conditions are studied. It is shown that the best efficiency of solar-to-electrical energy conversion, namely, 9.3%, is obtained for the PSC with a photoelectrode based on a TiO₂ film with an anatase/rutile mixed phase ratio of 86/14%.     

硒化技术对CuInSe2薄膜表面形貌和晶相的影响

以共溅射法制备的Cu-In预制膜为衬底材料，以硒粉为原料，尝试了几种特殊的硒化方案，包括单源硒化法、双源硒化法、表面喷粉硒化法、分步硒化退火和同步硒化退火等5种具有代表性和创新性的方案，研究了硒源的摆放方式、升温方法对薄膜质量的影响，比较了不同方法制备的CuInSe₂(CIS)薄膜在形貌、成分、相结构等方面的异同. 系统地分析了硒化温度、退火温度和退火时间对CuInSe₂薄膜成分的影响，研究了各元素的百分含量随硒化退火条件的变化规律，为更准确地把握CIS薄膜的成分和相结构提供有益的借鉴.     

旋涂法制备WO3薄膜电致变色性能

"智能窗"大规模推广顺应可持续发展潮流,三氧化钨(WO_3)是生产"智能窗"的一种重要电致变色材料,但调控WO_3薄膜电致变色性能机制仍待进一步研究。采用旋涂法制备WO_3薄膜,重点研究了溶液浓度和旋涂次数对调控WO_3薄膜电致变色性能的影响。通过表面轮廓仪测量薄膜厚度,X射线衍射(XRD)测量薄膜结晶情况,原子力显微镜(AFM)和扫描电子显微镜(SEM)分析薄膜表面形貌,光谱仪测量薄膜初始态、着色态和褪色态的透射率。实验结果表明,随着溶液浓度增加(0. 2～1. 0 mol/L),薄膜厚度从9. 7 nm增加到33. 3 nm,透射率调制能力从0%提升到37. 0%;多次旋涂薄膜厚度线性增长,线性拟合优度(R~2)达0. 98,5次旋涂后透射率调制能力达51. 3%。改变溶液浓度和旋涂次数都是调控薄膜透射率调制能力的有效手段,精准调控薄膜透射率调制能力对设计不同应用场景的电致变色器件具有重大意义。     

Characterization of Cu(In,Ga)Se2 thin films prepared by evaporationfrom ternary compounds

Thin films of Cu(In,Ga)Se₂ were fabricated by evaporation from ternary CuGaSe₂ and CuInSe₂ compounds for photovoltaic device applications and their properties were investigated. From XRF analysis, the Cu:(In+Ga):Se atomic ratio in all thin films was approximately 1:1:2. The Ga/(In+Ga) atomic ratio in the thin films changed linearly from 0 to 1.0 with increasing the [CGS]/([CGS]+[CIS]) mole ratio in the evaporating materials. However, for thin films prepared at the [CGS]/([CGS]+[CIS]) mole ratio above 0.4, the composition by EPMA analysis was not consistent with that by XRF analysis. The result of EPMA analysis showed that the surface of a thin film was Cu-rich. XRD studies demonstrated that the thin films prepared at the [CGS]/([CGS]+[CIS]) mole ratio under 0.2 had a chalcopyrite Cu(In,Ga)Se₂ structure and the preferred orientation to the 112 plane. On the other hand, XRD patterns of the thin films produced at the [CGS]/([CGS]+[CIS]) mole ratio above 0.6 showed the diffraction lines from a chalcopyrite Cu(In,Ga)Se₂ and a foreign phase. The separation of a peak was observed near 2θ=27°, indicative the graded Ga concentration in Cu(In,Ga)Se₂ thin film.     

Nb/SnO2复合薄膜的制备、结构及光电性能

用溶胶-凝胶旋涂法在玻璃基底上制备出Nb/SnO₂复合透明导电薄膜,利用XRD,SEM,紫外—可见分光光度计,四探针电阻仪等测试方法对Nb/SnO₂复合薄膜的结构和物性进行了研究.结果表明: 当Nb含量小于0.99at%时,Nb/SnO₂复合薄膜为较纯的四方金红石结构;复合薄膜中晶粒分布均匀,平均尺寸在5—7 nm.当Nb含量小于0.99at%时,Nb/SnO₂复合薄膜的电阻率先减小后增大,当Nb含量为0.37at%时 关键词： 溶胶-凝胶法 2复合薄膜')" href="#">Nb/SnO₂复合薄膜 结构表征 光电性能     

Improved ferroelectric,dielectric and magnetic properties with La- and Mn- doped Bi5Ti3FeO15 thin films

A series of La and Mn co-doped Bi₅Ti₃FeO₁₅ (BLTFMO) thin films were prepared by spin-coating deposition route. X-ray diffraction, atomic force microscopy and scanning electron microscopy were used to characterize the structures of these BLTFMO thin films. Ferromagnetic properties are obtained as the La-doping content is 0, 0.1, 0.2, and 0.3 with the transition temperature of 127.2 K, 65.1 K, 48.1 K, and 7.9 K, respectively. Well-defined ferroelectric loops are found in all these BLTFMO films, and a higher remnant polarization of 27.84, 24.21 and 24.02 μC/cm² is obtained in the 0.1, 0.2 and 0.3 La-doped films, respectively. A weak dielectric dispersion for the BLTFMO without La-doping, a strong one in 0.1, 0.2, 0.3 and 0.4 La doped films as indicated by the appearance of a dielectric loss peak, and a weak dispersion in 0.6, 0.8 and 1 La doped ones are demonstrated.     

Valence control of cobalt oxide thin films by annealing atmosphere

The cobalt oxide (CoO and Co₃O₄) thin films were successfully prepared using a spin-coating technique by a chemical solution method with CH₃OCH₂CH₂OH and Co(NO₃)₂·6H₂O as starting materials. The grayish cobalt oxide films had uniform crystalline grains with less than 50 nm in diameter. The phase structure is able to tailor by controlling the annealing atmosphere and temperature, in which Co₃O₄ thin film was obtained by annealing in air at 300-600, and N₂ at 300, and transferred to CoO thin film by raising annealing temperature in N₂. The fitted X-ray photoelectron spectroscopy (XPS) spectra of the Co2p electrons are distinguishable from different valence states of cobalt oxide especially for their satellite structure. The valence control of cobalt oxide thin films by annealing atmosphere contributes to the tailored optical absorption property.