Optical properties and microstructure of Ta_2O_5 thin films prepared by oblique angle deposition

Tantalum pentoxide thin films are prepared by oblique angle electron beam evaporation. The influence of flux angle on the surface morphology and microstructure is investigated by scanning electron microscopy （SEM）. The Ta2O5 thin films are anisotropic with highly orientated nanostructure of slanted columns. The porous microstructure of the as-deposited films results in the decrease of effective refractive index and packing density with increasing deposition angle. The anisotropic structure results in optical birefringence. The in-plane birefringence increases with the increase of deposition angle and reaches the maximum of 0.055 at the deposition angle of 70°. Anisotropic microstructure and critical packing density are the two key factors to influence the in-plane birefringence.     

Influence of Annealing Temperature on Structure, Optical Loss and Laser-Induced Damage Threshold of TiO2 Thin Films

TiO2 thin films are prepared on fused silica with conventional electron beam evaporation deposition. After annealed at different temperatures for 4h, the spectra and XRD patterns of the TiO2 thin film are obtained. Weak absorption of coatings is measured by the surface thermal lensing technique, and laser-induced damage threshold （LIDT） is determined. It is found that with the increasing annealing temperature, the transmittance of TiO2 films decreases. Especially when coatings are annealed at high temperature over 1173K, the optical loss is very serious. Weak absorption detection indicates that the absorption of coatings decreases firstly and then increases, and the absorption and defects play major roles in the LIDT of TiO2 thin films.     

Influence of HF catalyst on the microstructure properties of ultra low-k thin films prepared by sol-gel method

This paper reports that by using the hydrofluoric acid （HF） as the acid catalyst, F doped nanoporous low-k SiO2 thin films have been prepared by means of sol-gel method. The characterization of atomic force microscopy and Fourier transform infrared spectroscopy demonstrates that the HF catalyzed films are more hydrophobic. The N2 adsorption/desorption experiments show that the suited introduction of HF increases the porosity and decreases the pore size distribution （about 10 nm） in the films. The above results indicate that the hydrofluoric acid is the more suitable acid catalyst than the hydrochloric one for preparing nanoporous ultra low-k SiO2 thin films.     

Structural and Optical Properties of Zinc Nitride Films Prepared by Pulsed Filtered Cathodic Vacuum Arc Deposition

Polycrystalline zinc nitride films are deposited on Coming 7059 glass substrates by pulsed filtered cathodic vacuum arc deposition （PFCVAD）. The crystallographic structure is studied by means of x-ray diffraction. These measurements show that all the films are crystallized in the cubic structure, in a preferred orientation along the （332） and （631） directions. Weak XRD signal shows small crystallites distributed in an amorphous tissue. A small improvement of crystallinity is observed with annealing. Optical parameters such as absorption, energy band gap, Urbach tail, extinction coefficients have been determined. The Urbach tail energy is decreased with annealing at 500℃ for one hour. Energy band gap values are found to be increased by annealing.     

Characteristics of Sn-Doped Ge2Sb2Te5 Films Used for Phase-Change Memory

Sn-doped Ge2Sb2Te5 thin films deposited on Si（100）/SiO2 substrates by rf magnetron sputtering are investigated by a differential scanning calorimeter, x-ray diffraction and sheet resistance measurement. The crystallization temperatures of the 3.58 at.%, 6.92 at.% and 10.04 at.% Sn-doped Ge2Sb2Te5 thin films have decreases of 5.3, 6.1 and 0.9℃, respectively, which is beneficial to reduce the switching current for the amorphous-to-crystalline phase transition. Due to Sn-doping, the sheet resistance of crystalline Ge2Sb2Te5 thin films increases about 2-10 times, which may be useful to reduce the switching current for the amorphous-to-crystalline phase change. In addition, an obvious decreasing dispersibility for the sheet resistance of Sn-doped Ge2Sb2Te5 thin films in the crystalline state has been observed, which can play an important role in minimizing resistance difference for the phase-change memory cell element arrays.     

Multi-layer structures including zigzag sculptured thin films for corrosion protection of AISI 304 stainless steel

To increase corrosion resistance of the sample,its electrical impedance must be increased.Due to the fact that electrical impedance depends on elements such as electrical resistance,capacitance,and inductance,by increasing the electrical resistance,reducing the capacitance and inductance,electrical impedance and corrosion resistance can be increased.Based on the fact that these elements depend on the type of material and the geometry of the material,multilayer structures with different geometries are proposed.For this purpose,conventional multilayer thin films,multilayer thin film including zigzag structure(zigzag 1)and multilayer thin film including double zigzag structure(zigzag 2)of manganese nitride are considered to protect AISI 304 stainless steel against corrosion in salt solution.These multilayer coatings including zigzag structures are prepared by alternately using the conventional deposition of thin film and glancing angle deposition method.After deposition,the samples are placed in a furnace under nitrogen flux for nitriding.The cross sections of the structures are observed by field emission scanning electron microscopy(FESEM).Atomic force microscope(AFM)is used to make surface analyses of the samples.The results show that the multilayer thin films including zigzag structures have smaller grains than conventional multilayer thin films,and the zigzag 2 structure has the smaller grain than the other two samples,which is attributed to the effect of shadowing and porosity on the oblique angle deposition method.Crystallography structures of the samples are studied by using x-ray diffraction(XRD)pattern and the results show that nitride phase formation in zigzag 2 structure is better than that in zigzag 1 structure and conventional multilayer thin film.To investigate the corrosion resistances of the structures,electrochemical impedance spectroscopy(EIS)and potentiodynamic polarization tests are performed.The results reveal that the multilayer thin films with zigzag structures have better corrosion protection than the conventional multilayer thin films,and the zigzag structure 2 has the smallest corrosion current and the highest corrosion resistance.The electrical impedances of the samples are investigated by simulating equivalent circuits.The high corrosion resistance of zigzag 2 structure as compared with conventional multilayer structure and zigzag 1 structure,is attributed to the high electrical impedance of the structure due to its small capacitance and high electrical resistance.Finally,the surfaces of corroded samples are observed by scanning electron microscope(SEM).     

The electric and magnetic properties of epitaxially grown A0.5-xLaxSr0.5MnO3 （A=Pr, Nd） thin film

The epitaxial （single crystal-like） Pr0.4La0.1Sr0.5MnO3 （PLSMO） and Nd0.35La0.15Sr0.5MnO3 （NLSMO） thin films are prepared and characterized, and the electric and magnetic properties are examined. We find that both PLSMO and NLSMO have their own optimum deposition temperature （To） in their growing into epitaxial thin films. When the deposition temperature is higher than To, a c-axis oriented but polycrystalline thin film grows; when the deposition temperature is lower than To, the thin film tends to be a-axis oriented and also polycrystalline. The most important point is that for the epitaxial PLSMO and NLSMO thin films the electronic phase transitions are closely consistent with the magnetic phase transitions, i.e. an antiferromagnetic phase corresponds to an insulating state, a ferromagnetic phase corresponds to a metallic state and a paramagnetic phase corresponds to a semiconducting state, while for the polycrystalline thin films the electronic phase transitions are always not consistent with the magnetic transitions.     

Low temperature ferromagnetic properties of CdS and CdTe thin films

The magnetic property in a material is induced by the unpaired electrons. This can occur due to defect states which can enhance the magnetic moment and the spin polarization. In this report, CdS and CdTe thin films are grown on FTO glass substrates by chemical bath deposition and close-spaced sublimation, respectively. The magnetic properties, which are introduced from oxygen states, are found in CdS and CdTe thin films. From the hysteresis loop of magnetic moment it is revealed that CdS and CdTe thin films have different kinds of magnetic moments at different temperatures. The M–H curves indicate that from 100 K to 350 K, CdS and CdTe thin films show paramagnetism and diamagnetism, respectively.A superparamagnetic or a weakly ferromagnetic response is found at 5 K. It is also observed from ZFC/FC curves that magnetic moments decrease with temperature increasing. Spin polarized density functional calculation for spin magnetic moment is also carried out.     

Effects of Substrate Temperature and Vacuum Annealing on Properties of ITO Films Prepared by Radio-Frquency Magnetron Sputtering

Indium tin oxide （ITO） films were prepared by rf magnetron sputtering under two conditions： （i） at substrate temperature Ts from room temperature （RT） to 350℃ （ii） with additional post-annealing in vacuum at 400℃ for 30 min in comparison of their crystalline structures, and electrical-optical properties of the films deposited. From the experimental results, it is found that, under the first condition, the crystalline structures and the electrical-optical properties of the films are improved with the increasing Ts. Under the other condition, i.e. with the additional post-annealing, the films exhibit higher degree of crystallinities and better electrical-optical properties. Under the two deposition conditions, inter-relation between electrical-optical properties and the crystalline structure is observed clearly. However, even under the same annealing condition, it is observed that improved properties of the films are different, depending on their deposition temperatures, which implies that an initial stage of the ITO film before annealing is an important factor for the film＇s properties improved after annealing. The resistivity of 2.33 × 10-4 Ω·cm can be achieved at Ts of 350℃after annealing.     

Structure Stability of LaAlO3 Thin Films on Si Substrates

A series of amorphous and single-crystalline LaAlO3 （LAO） thin films are fabricated by laser molecular-beam epitaxy technique on Si substrates under various conditions of deposition. The structure stability of the LAO films annealed in high temperature and various ambients is studied by x-ray diffraction as well as high-resolution transmission electron microscopy. The results show that the epitaxial LAO films have very good stability, and the structures of amorphous LAO thin films depend strongly on the conditions of deposition and post-annealing. The results reveal that the formation of LAO composition during the deposition is very important for the structure stability of LAO thin films.     

First-Principles Study on the Electronic Structures for Y^3＋：PbWO4 Crystals

The possible defect models of Y^3＋：PbWO4 crystals are discussed by defect chemistry and the most possible substituting positions of the impurity Y^3＋ ions are studied by using the general utility lattice program （GULP）. The calculated results indicate that in the lightly doped Y^3＋ ：PWO crystal, the main compensating mechanism is [2Ypb^＋ ＋ VPb^2-], and in the heavily doped Y^3＋ ：PWO crystal, it will bring interstitial oxygen ions to compensate the positive electricity caused by YPb^＋, forming defect clusters of [2Ypb^＋ ＋Oi^2-] in the crystal. The electronic structures of Y3＋ ：PWO with different defect models are calculated using the DV-Xα method. It can be concluded from the electronic structures that, for lightly doped cases, the energy gap of the crystal would be broadened and the 420nm absorption band will be restricted; for heavily doped cases, because of the existence of interstitial oxygen ions, it can bring a new absorption band and reduce the radiation hardness of the crystal.     

Application of Electron-Shelving Detection via 423 nm Transition in Calcium-Beam Optical Frequency Standard

A new scheme of small compact optical frequency standard based on thermal calcium beam with application of 423 nm shelving detection and sharp-angle velocity selection detection is proposed. Combining these presented techniques, we conclude that a small compact optical frequency standard based on thermal calcium beam will outperform the commercial caesium-beam microwave dock, like the 5071 Cs clock （from Hp to Agilent, now Symmetricom company）, both in accuracy and stability.     

Effects of in situ thermal annealing on the structural, optical, and electrical properties in Hg0.7Cd0.3Te epilayers grown on CdTe buffer layers

Scanning electron microscopy (SEM), Fourier transform infrared (FTIR) transmission, and Hall effect measurements were performed to investigate the structural, optical, and electrical properties of as-grown and in situ-annealed Hg_0.7Cd_0.3Te epilayers grown on CdTe buffer layers by using molecular beam epitaxy. After the Hg_0.7Cd_0.3Te epilayers had been annealed in a Hg-cell flux atmosphere, the SEM images showed that the surface morphologies of the Hg_0.7Cd_0.3Te thin films were mirror-like with no indication of pinholes or defects, and the FTIR spectra showed that the transmission intensities had increased in comparison to that of the as-grown Hg_0.7Cd_0.3Te epilayer. Hall-effect measurements showed that n-Hg_0.7Cd_0.3Te epilayers were converted to p-Hg_0.7Cd_0.3Te epilayers. These results indicate that the surface, optical, and electrical properties of the Hg_1 − xCd_xTe epilayers are improved by annealing and that as-grown n-Hg_1 − xCd_xTe epilayers can be converted to p-Hg_1 − xCd_xTe epilayers by in situ annealing.     

Suppression of Chaos and Phase Locking in Two Coupled Nonidentical Neurons under Periodic Input

Dynamical behaviour of two coupled neurons with at least one of them being chaotic is presented. Bifurcation diagrams and Lyapunov exponents are calculated to diagnose the dynamical behaviour of the coupled neurons with the increasing coupling strength. It is found that when the coupling strength increases, a chaotic neuron can be controlled by the coupling between neurons. At the same time, phase locking is studied by the maxima of the differences of instantaneous phases and average frequencies between two coupled neurons, and the inherent connection of phase locking and the suppression of chaos is formulated. It is observed that the onset of phase locking is closely related to the suppression of chaos. Finally, a way for suppression of chaos in two coupled nonidentical neurons under periodic input is suggested.     

Fabrication of Long-Period Fibre Gratings Using 800 nm Femtosecond Laser Pulses

Long-period fibre gratings inside standard single-mode optical communication fibres are successfully fabricated with infrared femtosecond laser pulses. The refractive index perturbations are well confined within the fibre core by choosing the proper laser focusing parameters and translation speed of the fibre during the direct laser writing process. With the self-focusing effect considered and at a constant average irradiation dose of 1.62 × 10^3 J/（cm^2μm）, the threshold intensity for fabricating long-period gratings with infrared femtosecond laser pulses is determined to be 5.13 × 10^13 W/cm2.     

Dependence of the interband transitions on the in mole fraction and the applied electric field in InxGa1−xAs/In0.52Al0.48As multiple quantum wells

Transmission electron microscopy (TEM) and photocurrent (PC) measurements were carried out to investigate the microstructural properties and excitonic transitions in In_xGa_1−xAs/In_0.52Al_0.48As multiple quantum wells (MQWs) for x = 0.54, 0.57 and 0.60. TEM images showed that high-quality 11-period In_xGa_1−xAs/In_0.52Al_0.48As MQWs had high-quality heterointerfaces. The results for the PC spectra at 300 K showed that the peaks corresponding to the excitonic transitions from the ground state electronic sub-band to the ground state heavy-hole band (E₁-HH₁) and the ground state electronic sub-band to the ground state light-hole band (E₁-LH₁) became closer to each other with decreasing In mole fraction and that E₁-HH₁ and E₁-LH₁ excitonic peaks shifted to longer wavelength with increasing applied electric field. The calculated values of the E₁-HH₁ interband transition energies were in qualitative agreement with those obtained form the PC measurements with and without applied electric field. These results can be helpful in understanding potential applications of In_xGa_1−xAs/In_yAl_1−yAs MQWs dependent on In mole fraction and applied electric field in long-wavelength optoelectronic devices.     

Rotational Brownian Motion on Sphere Surface and Rotational Relaxation

The spatial components of the autocorrelation function of noninteracting dipoles are analytically obtained in terms of rotational Brownian motion on the surface of a unit sphere using multi-level jumping formalism based on Debye＇s rotational relaxation model, and the rotational relaxation functions are evaluated.     

A Complete Foliation of Schwarzschild Spacetime by Free Falling Hypersurfaces

Free falling hypersurfaces in the Schwarzschild geometry have been studied to provide a complete foliation of spacetime. The hypersurfaces do not cross into the maximally extended spacetime and are well behaved everywhere except at the singularity r =0 the mean extrinsic curvature becomes infinity.     

Self Mixing Fringes of Vertical-Cavity Surface-Emitting Lasers under Dual Reflector Feedback

The self-mixing fringes which shift due to every one-twentieth wavelength displacement of the target are observed. Taking advantage of the dual reflectors in the external cavity of lasers, the resolution of the sensors has been improved by 10 times. The role of the each reflector has been discussed in detail.