Leaky pseudo surface wave on the water–Si(110) interface

The present letter demonstrates that a leaky pseudo surface wave (LPSW) should exist on the interface of water and a cubic crystal silicon (110) plane. The phase velocity distribution of the LPSW on the above interface has been theoretically predicted by the reflection coefficient analysis and experimentally measured by using acoustic spectro-microscopy (ASM). The measured phase velocity distribution of the LPSW is in good agreement with the predicted one.     

Coherent combination of two ytterbium fiber amplifier based on an active segmented mirror

To control the phase noise of two ytterbium fiber amplifiers, a coherent combination system based on an active segmented mirror (ASM) has been established in our laboratory. The ASM is controlled by a feed back control loop on the basis of a Peak Rate (PR) algorithm which is realized on a DSP + FPGA hardware control board. Experimental results indicate that when the control loop is off, the far-field interference pattern is blurred and dynamic, while when it is on, the far-field beams interference pattern achieves clear and stable. At two different output powers, the contrasts of the interference stripes are improved from 7% to 19% and 8% to 28% respectively.     

多面转镜激光器扫频光学相干层析成像系统的全光谱重采样方法

在多面转镜激光器扫频光学相干层析成像系统中,激光器存在着输出光谱错位与扫频范围波动的问题.目前的重采样方法中,普遍利用互相关运算校正光谱错位,并进行大范围的截取,保证扫频范围的一致性,但这会导致成像信噪比与分辨率的降低.本文用马赫-曾德尔干涉仪(MZI)采集到的干涉信号对扫频范围波动的问题进行了详细的测量与分析,其中干涉信号的解缠相位曲线的非随机性和平行性,表明该类激光器输出光谱的波长分布具备一致性.在此基础上,提出了一种用最长扫频范围的MZI干涉信号,对样品干涉信号进行时域光谱对齐、然后进行一对多插值的重采样方法.实验与分析表明,该方法利用了所有的光谱信号,保证了样品干涉信号的能量利用率,能有效提高图像的信噪比与分辨率.     

傅里叶变换轮廓术中相位失真的预矫正方法

介绍了一种基于傅里叶变换轮廓术的三维面形测量系统中相位失真的预矫正方法。由于投影系统和成像系统的空间三角位置关系、投影仪的发散照明和两套系统蕴含的光学畸变,投影一幅相位与空间坐标成理想线性关系的标准正弦光场,拍摄到的条纹相位和空间坐标不再呈线性分布,引起相位失真,甚至会影响系统测量精度。该方法借鉴反向条纹投影的思想,计算拍摄光场的非线性相位分布与理想的线性相位分布之间的关系,预先矫正,反算出一个新的待投影光场。实验结果表明这种方法能有效地减小该类相位失真所导致的测量误差,获得了更好的测量结果．     

驾驶人眼睛区域的鲁棒性定位算法研究

疲劳驾驶是造成交通事故的重要原因. 通过机器视觉技术对眼睛动作和视线转移特征的分析可实现驾驶人疲劳状态的有效估计. 然而, 实际行车环境中光照条件的随机、快速变化以及驾驶人面部姿态的不确定性使得眼睛区域的鲁棒性定位变得异常困难. 为此, 本文引入基于点分布模型的主动形状模型(ASM)算法并针对其在实际行车环境中存在的问题提出了三点改进. 首先, 建立了基于自商图的局部纹理模型以克服光照变化的影响; 其次, 充分利用面部局部区域良好的聚类性, 建立了层叠式全局形状模型, 以适应驾驶人姿态的大角度偏转; 再次, 在行车过程中, 通过对驾驶人面部形状的在线学习实现模型参数分布特征的获取, 为ASM算法的配准提供了更加紧致的约束. 实验结果显示, 本文算法对光照和姿态变化具有较强的鲁棒性, 在驾驶人面部器官不发生自遮挡的情况下可实现眼睛区域的高精度配准.     

Interpolation algorithm for recovering the missing phase values in 3D measurement

In the three-dimensional (3D) phase measurement, some marks are usually adhered to the object in order to make the 3D registration process faster and easier. As covered with marks, local phase data are missing and have to be interpolated later. Considering the phase distribution nearby the marks, a gradient estimate (GE) interpolation algorithm is provided here. This algorithm recovers one pixel's missing phase value with the average of the estimated values which is calculated by gradients in eight directions nearby. Since this algorithm is a local processing, the missing phase values should be interpolated from the edge of the marks to the center. In the computer simulation and the practical experiment, compared with the same-size neighborhood mean (NM) algorithm and the Gerchberg-Saxton (GS) algorithm, this new algorithm achieves very good fit results with the least time. So it can be used as a practical tool for automatic missing phase interpolation.     

Surface plasmon interferometric microscopy for three-dimensional imaging of dynamic processes

A method, which we named surface plasmon interferometric microscopy, for real-time displaying of the dynamic evolution of the refractive index (RI) of a sample in three-dimensions is demonstrated experimentally. The Fourier fringe analysis technique is employed to get the phase variations of the samples by demodulating the interference patterns captured by a CCD camera, and the 3D RI distribution can be obtained through numerical interpolation from the relation between the phase and the RI of the samples. Our method may provide an interesting way to monitor fast dynamics of physical, biological, and chemical processes in real time.     

Interferometric grating method and its application in Fe-base shape memory alloy structure design

This paper presents an interferometric grating method used in measuring strain fields on a curved surface. This method can be used to determine the small and large strains with high sensitivity and has been applied successfully in Fe-base shape memory alloy (FSMA) structure design. In this study, five diffracted beam from the specimen surface produce the interferometric gratings through an optical system. Using image processing technique (fast Fourier transform with special interpolation and phase shifting technique), we have obtained the strain fields of outer surface of FSMA joint and contact pressure distribution on its inside surface which has mechanical deformation and transformation.     

Performance of discrete dipole approximation for prediction of amplitude and phase of electromagnetic scattering by particles

Electromagnetic scattering provides useful signatures for nonintrusive particle characterization. Scattered wave which carries characteristic information about particles is identified completely by its intensity, polarization state and phase. Recent developments in measurement techniques have enabled measurement of phase of the scattered wave which is a source of additional information about particles. In the present study, accuracy of discrete dipole approximation (DDA) in predicting amplitude and phase of scattered wave is investigated via publicly available DDSCAT code by Draine and Flatau, which is a well-established tool for DDA and has found wide range of applications in the literature due to its flexibility. DDSCAT routine is modified to enable accurate computation of phase of complex amplitude scattering matrix (ASM) elements as well as their magnitude. DDA method was implemented by using lattice dispersion relation for dipole polarizabilities, generalized prime factor algorithm for fast-Fourier transformation and pre-conditioned bi-conjugate gradient method with stabilization for the solution of the complex linear system of equations. Accuracy of ASM elements predicted by DDA is assessed on single sphere problems with various size parameters and refractive indices by validation against Mie theory solutions. Excellent agreement between predictions and exact solutions proves the reliability of the modified DDSCAT code for prediction of amplitude and phase of scattered electromagnetic wave. Applicability conditions and requirements of the present DDA application to ensure accurate prediction of complete set of scattering parameters are mapped for single spheres, on an extensive domain of size parameters and refractive indices. A correlation is presented to estimate the magnitude and phase errors associated with given size parameter, refractive index and cubic lattice subdivision. Assessment of computational time requirements for different optical constants shows that implementation of DDA with the present specifications is unfeasible for size parameters larger than 4 when Re(m)>2 and Im(m)<0.1 at the same time, due to slow convergence rate.     

Impact parameter calculation of electron impact excitation of hydrogen

The convenience of a diabatic or an adiabatic interpolation of frequencies in variational transition state calculations involving interpolation methodologies is discussed. The gas phase proton transfer between butanone and a hydroxide anion has been used to illustrate the theoretical discussion. For example, it has been shown that if vibrational normal mode crossings exist the simple adiabatic interpolation can produce incorrect entropy contributions and, as a consequence, a spurious displacement of the generalized transition state.     

A Probabilistic Approach to Zhang’s Sandpile Model

The current literature on sandpile models mainly deals with the abelian sandpile model (ASM) and its variants. We treat a less known - but equally interesting - model, namely Zhang’s sandpile. This model differs in two aspects from the ASM. First, additions are not discrete, but random amounts with a uniform distribution on an interval [a, b]. Second, if a site topples - which happens if the amount at that site is larger than a threshold value E _c (which is a model parameter), then it divides its entire content in equal amounts among its neighbors. Zhang conjectured that in the infinite volume limit, this model tends to behave like the ASM in the sense that the stationary measure for the system in large volumes tends to be peaked narrowly around a finite set. This belief is supported by simulations, but so far not by analytical investigations. We study the stationary distribution of this model in one dimension, for several values of a and b. When there is only one site, exact computations are possible. Our main result concerns the limit as the number of sites tends to infinity. We find that the stationary distribution, in the case a ≥ E _c /2, indeed tends to that of the ASM (up to a scaling factor), in agreement with Zhang’s conjecture. For the case a = 0, b = 1 we provide strong evidence that the stationary expectation tends to .     

光学元件表面频谱分布影响因素的分析方法

 精密光学系统对光学元件的表面频谱误差的分布提出了控制要求,在加工中如何检测和控制光学元件表面的频谱分布成为一个新的问题。利用功率谱密度对频率的定量化描述功能,对检测数据进行样条插值,在同一极坐标系下计算功率谱密度,求取功率谱密度比值信息,分析小磨具技术的加工工具性能、形状及其运动方式对光学元件表面的频率分布影响。指出在加工中合理地改变加工参数可以快速有效地控制元件表面频谱的分布特征。在670 mm大口径非球面镜加工中做了验证。     

一种新的单幅条纹图的相位解调方法

基于非载波条纹图的条纹灰度分布的极值准确定位,提出了一种新的由单幅条纹图解调相位方法.该方法首先准确定位每个条纹灰度的极值包括最大和最小,再基于极值图将条纹的强度值分布线性地变换到-1和1之间,最后利用arcos反余弦取代传统的atan2反正切算法求出相位,结合极值图就能快速准确地解调出含有封闭条纹的条纹图相位.本方法仅用一幅条纹图,不需要传统的条纹定级和对分数级条纹插值与拟合,自动判别条纹相位变化的波谷,准确获得条纹相位分布.这一方法使光测法研究动态和瞬态问题成为可能,而不需引入载波法调制条纹.文中通过实例说明了本方法的处理过程.     

Adaptive computer-generated hologram using interpolation method

Kinoform synthesis by an electro-optic hybrid system using an interpolation method is proposed. A programmable liquid crystal spatial light modulator is used as a kinoform. The phase distribution of the kinoform is optimized using the simulated annealing. The cost function is represented by the mean square error between a desired image stored in a computer and a reconstructed image detected by a charge coupled device camera. The interpolation method enables one to reduce the random noise effect in the reconstructed image. Some experimental results are presented. Presented at 1996 International Topical Meeting on Optical Computing (OC’96), April 21–25, Sendai, Japan.     

不等长相移效应滤波器的快速调试方法北大核心CSCD

提出一种基于渐进空间映射算法(ASM)与遗传算法(GA)相结合的I/O端口不等长相移效应的滤波器快速调试方法。渐进空间映射算法能够准确预测精细模型的调试方向与幅度,遗传算法能够准确快速得到I/O端口的相移效应,并且通过柯西法提取粗糙模型。基于有限元的全波电磁仿真软件HFSS,建立精细模型,粗糙模型参数即等效电路参数,则由去除I/O端口处相移效应后的S参数获得。利用该方法对六阶交叉耦合滤波器进行调试,经过几步迭代即可使滤波器满足所要求的响应指标,验证了该调试方法的正确性和有效性。     

无透镜显微成像的重构算法研究

针对单幅图像进行了无透镜显微成像的重构算法研究，介绍了无透镜显微成像系统实验装置和ASM(angle spectrum method)、改编后的L-R(Lucy-Richardson)两种重构算法。对比两种算法重构后的USAF分辨率板图像的分辨率，利用瑞利判据得出ASM获得的振幅图分辨率最高(即3.10 μm)，且计算用时最少(即0.9 s)，证明了ASM为最佳的单幅无透镜显微重构算法。其次，利用无透镜显微成像系统结合ASM重构的方法，进行细胞成像实验。该无透镜成像视场为5×显微镜的4.4倍，且分辨率介于5×及10×光学显微镜之间，统计学优势明显，在生物医学领域具有广阔的应用前景。     

在计算机中实现三角函数的硬件解算方法

针对目标跟踪中大量存在的三角函数运算,提出在火控计算机中建立三角函数解算单元,采用硬件实现三角函数解算的设想。而三角函数解算单元是一种可以完成正弦函数解算功能的函数芯片。它的设计核心是以角度值为地址,通过硬件查表计算,可对0到90度的正弦函数值进行查表。查表精度可设计到0.001°,最大查表时间即为函数值的解算时间。余弦查表计算是采用正弦同一芯片,可以根据相位差90度的关系进行查表。实践表明三角函数的硬件解算速度快,精度高,可以替代通常方法的函数解算。因此,如果在火控系统中,设计一个地址译码器电路,就可建立多个三角函数芯片解算单元,通过计算机数据指令,实现对多个三角函数值的并行计算,从而提高系统对多个目标的快速跟踪处理能力。     

A digital phase-measurement system for real-time holographic interferometry

While holographic interferometry gives a good picture of the stress distribution over a complex structure, its use in stress-analysis has been limited by the fact that quantitative information on the deformation of the surface is directly available only at points on the fringe maxima or minima, and interpolation between these points is slow and not very accurate. An improved phase-measurement system for real-time holographic interferometry is described. This uses a diode array television camera to view the interference pattern, and digital electronics to calculate and store the phase difference at a 100 × 100 grid of points. This permits measurements of the phase with an accuracy estimated at ±2°.     

Verifiable Quantum (<Emphasis Type="Italic">k</Emphasis>,<Emphasis Type="Italic">n</Emphasis>)-threshold Secret Key Sharing

Based on Lagrange interpolation formula and the post-verification mechanism, we show how to construct a verifiable quantum (k,n) threshold secret key sharing scheme. Compared with the previous secret sharing protocols, ours has the merits: (i) it can resist the fraud of the dealer who generates and distributes fake shares among the participants during the secret distribution phase; Most importantly, (ii) It can check the cheating of the dishonest participant who provides a false share during the secret reconstruction phase such that the authorized group cannot recover the correct secret.     

基于DFT插值的线性约束最小方差宽带自适应阵列

本文提出一种具有频率不变波束图的线性约束最小方差宽带自适应算法。首先给出了具有频率不变波束图的连续线阵的灵敏度函数与离散线列阵加权系数之间的关系，然后给出了使用DFT插值法求解各子带阵列权系数的方法，最后将DFT插值法应用于线性约束最小方差宽带自适应阵列。理论分析及仿真结果表明，该算法可以在实现最小方差波束形成的同时保持波束图基本不随频率变化，且该方法可以降低宽带自适应阵列的运算量。