Vacuum Arc Anode Phenomena

This paper briefly reviews anode phenomena in vacuum arcs, specially experimental work. It discusses, in succession, arc modes at the anode, anode temperature measurements, anode ions, transitions of the arc into various modes (principally the anode spot mode), and theoretical explanations of anode phenomena. The two most common anode modes in a vacuum arc are a low current mode where the anode is basically passive, acting only as a collector of particles emitted from the cathode, and a high current mode with a fully developed anode spot. Characteristically this anode spot has a temperature near the atmospheric boiling point of the anode material and is a copious source of vapor and energetic ions. However, other anode modes can exist. A low current vacuum arc with electrodes of readily sputterable material may emit a flux of sputtered atoms from the anode. Usually this sputtered flux will have little effect upon the vacuum arc, but in certain circumstances it could be significant. A vacuum arc doesn't always transfer directly from a low current mode to the anode spot mode. In appropriate experimental conditions, formation of an anode spot may be preceded by the formation of an anode footpoint. This footpoint is luminous, but much cooler than a true anode spot. Finally, (again in appropriate circumstances) several small anode spots may form instead of one large anode spot. With sufficient increase in arc current or arcing time these will usually combine to form a single large active spot.     

Vacuum Arc Anode Phenomena

This paper presents a brief review of anode phenomena in vacuum arcs. It discusses in succession the transition of the arc into the anode spot mode; the temperature of the anode before, during, and after formation of an anode spot; and anode ions. Characteristically the anode spot has a temperature of the order of the atmospheric boiling point of the anode material and is a copious source of vapor and energetic ions. The dominant mechanism controlling the transition of the vacuum arc into the anode spot mode appears to depend upon the electrode geometry, the electrode material, and the current waveform of the particular vacuum arc being considered. Either magnetic constriction in the gap plasma or gross anode melting can trigger the transition, indeed a combination of the two is a common cause of anode spot formation.     

Vacuum arc cathode spot grouping and motion in magnetic fields

Two of the important vacuum arc phenomena observed when the arc runs in a transverse magnetic field are cathode spot grouping and the cathode spot retrograde motion, i.e., in the anti-Amperian direction. This paper summarizes the main experimental observations and proposes a physical model for spot grouping and spot retrograde motion. The proposed spot motion model take in account the previous theoretical model of the cathode thermal regime and the plasma flow near the cathode surface that is based on two conditions: i) the heat loss in the cathode bulk is relatively small to the heat influx, and ii) the plasma flow in the Knudsen layer is impeded. In the present model, the current per group spot is calculated by assuming that the plasma kinetic pressure is comparable to the self-magnetic pressure in the acceleration region of cathode plasma jet. The model includes equations for the current per spot group, spot velocity dependence on the magnetic field and on the arc current in vacuum, as well as in gas filled arc gap. The calculated currents per spot group and spot velocity increase linearly with the magnetic field and arc current, and this dependencies well agree with previous observations. The cathode spot retrograde motion in short electrode gaps and at atmospheric pressure arcs, and the reversal motion in strong magnetic fields (>1 T) observed by Robson and Engel are discussed. The details of the retrograde motion observed in the last decades including the spot velocity dependence on the electrode gap, roughness, temperature, and material could be understood in the frame of the proposed model.     

Twenty-five years of progress in vacuum arc research andutilization

Progress in understanding and applying vacuum arcs is reviewed. Laser diagnostics have demonstrated the existence of micron-sized regions in the cathode spot plasma having electron densities exceeding 10²⁶ m^-3. The expanding plasma produces a highly ionized jet whose ions typically have charge states of 1-3 and energies of 50-150 eV. Gas dynamic and explosive emission models have been formulated to explain cathode spot operation. In cases where the arc is constricted at the anode, forming an anode spot, or the anode is thermally isolated, forming a hot anode vacuum arc, material emitted from the anode may dominate the interelectrode plasma. Evaporation from liquid droplets may also provide a substantial component of the plasma, and the presence of these droplets can have deleterious consequences in applications. The vacuum arc has been extensively utilized as a plasma source, particularly for the deposition of protective coatings and thin films, and as a switching medium in electrical distribution circuit breakers     

A Unified Explanation of Phenomena in Short Metal-Vapour Arcs in Air

Two types of short metal-vapour arcs between closely spaced noble-metal electrodes are distinguished: the anode and the cold cathode arc. Examination of electrode damage due to low-current (2-10A) field-emission-breakdown arcs and inductive break arcs in atmospheric air has led to the observation of two phenomena apparently contradicting to each other, firstly the existence of Germer's critical electrode distance and secondly, the occurrence of a steady transition from the anode to the cathode type with increasing arc duration. The physical interpretation of this are behaviour communicated in this report is based on the appearance of internal ionization instabilities of the self-sustained plasma-cathode system of the fast moving cold cathode spot for electrode separations near the axial extent of the spot ionization region. The concept includes the question of arc striking mechanism and a model of arc evolution with arc time.     

纵磁作用下真空电弧单阴极斑点等离子体射流三维混合模拟

真空电弧的特性直接受到从阴极斑点喷射出的等离子体射流的影响,对等离子体射流进行数值仿真有助于我们深入了解真空电弧的内部物理机制.然而,磁流体动力学和粒子云网格仿真方法受限于计算精度和计算效率的原因,无法有效地应用于真空电弧等离子体射流仿真模拟.本文开发了一套三维等离子体混合模拟算法,并在此基础上建立了真空电弧单阴极斑点射流仿真模型,模型中将离子作宏粒子考虑,而电子作无质量流体处理,仿真计算了自生电磁场与外施纵向磁场作用下等离子体的分布运动状态.仿真结果表明,单个阴极斑点情况下真空等离子体射流在离开阴极斑点后扩散至极板间,其整体几何形状为圆锥形,离子密度从阴极到阳极快速下降.外施纵向磁场会压缩等离子体,使得等离子体射流径向的扩散减少并且轴线上的离子密度升高.随着外施纵向磁场的增大,其对等离子体射流的压缩效应增强,表现为等离子体射流的扩散角度逐渐减小.此外,外施纵向磁场对等离子体射流的影响也受到电弧电流大小的影响,压缩效应随电弧电流的增加而逐渐减弱.     

A physical model of the low-current-density vacuum arc

A one-dimensional (1-D) physical model of the low-current-density steady-state vacuum arc is proposed. The model is based on the continuity equations for ions and electrons and the energy balance for the discharge system; the electric potential distribution in the discharge gap is assumed to be nonmonotonic. It is supposed that the ion current at the cathode is generated within the cathode potential fall region due to the ionization of the evaporated atoms by the plasma thermal electrons having Boltzmann's energy distribution. The model offers a satisfactory explanation for the principal regularities of a hot-cathode vacuum arc with diffuse attachment of the current. The applicability of the model proposed to the explanation of some processes occurring in a vacuum arc, such as the flow of fast ions toward the anode, the current cutoffs and voltage bursts, and the backward motion of a cathode spot in a transverse magnetic field is discussed     

Time-spatial structure of an electric arc anode region

This paper studies the anode region of an eroding anode with a nonstationary arc-root attachment. High-current free-burning short as well as long arcs at atmospheric pressure are investigated. A technique to study the anode region of the arc is suggested. An anode moving perpendicular to the arc axis was used for estimating parameters of the anode jets at a given moment of their development. The mechanism of current transfer in the anode region is considered on the basis of electrophysical and optical-spectroscopic investigations of the arc attachment traces and plasma parameters both of the anode jet and arc column. The anode jet was found to be of importance in the stationary arc operation. The near-anode plasma parameters depend on the effect of the cathode jet. In short arcs (L_a~2 mm), the plasma temperature at the anode exceeds 20000 K, while in long arcs (L_a >50 mm), it falls below 7000 K. At plasma temperature T_a >11000 K, the total arc current in the anode region is transferred through the arc plasma, while at lower temperatures, both the arc column and the anode jet take part in the current transfer     

Observation of tungsten particles in vacuum arcs by laser inducedfluorescence

We have clarified the relation between the decay of tungsten ion density in the vicinity of current zero and vacuum arc mode in high current period by using a laser induced fluorescence method in tungsten vacuum arcs of 60 Hz sinusoidal current with the peak value of 3.3, 6.7, and 9.8 kA. In the case of 6.7 kA, the arc mode was the anode spot mode. Because of the generation of the anode spot, the tungsten ion density near the anode was higher than near the cathode and the density near the anode was about ten times as high as the case of 3.3 kA which was the diffuse mode. In the case of 9.8 kA, which was the intense arc mode, the density near the anode was not significantly different from the case of 6.7 kA. The density near the cathode was higher than near the anode and tungsten ions were observed till about 30 μs after current zero while they disappeared at current zero in the other cases     

A Review of Anode Phenomena in Vacuum Arcs

This paper discusses arc modes at the anode, anode temperature measurments, anode ions, transitions of the arc into various modes (principally the anode-spot mode), and theoretical explanations of anode phenomena. A vacuum arc can exhibit five anode discharge modes: 1) a low-current mode in which the anode is basically passive, acting only as a collector of particles emitted from the cathode; 2) a second low-current mode that can occur if the electrode material is readily sputtered (a flux of sputtered atoms will be emitted by the anode); 3) a footpoint mode, characterized by the appearance of one or more luminous spots on the anode (footpoints are much cooler than the true anode spots present in the last two modes); 4) an anode-spot mode in which one large or several small anode spots are present (such spots are very luminous, have a temperature near the atmospheric boiling point of the anode material, and are a copious source of vapor and ions); and 5) an intense-arc mode where an anode spot is present, but accompanied by severe cathode erosion. The arc voltage is relatively low and quiet in the two low-current modes and the intense-arc mode. It is usually high and noisy in the footpoint mode, and it can be either in the anode-spot mode. Anode erosion is low, indeed negative, in the two low-current modes, and it is low to moderate in the footpoint mode. Severe anode erosion occurs in both the anode-spot and intense-arc modes.     

Investigation of ion behavior associated with anode-spot modetransition in vacuum arcs

The ion behavior phenomenon associated with transitions of the anode discharge mode to the anode-spot mode is studied by measuring the wall ion current and by spectroscopic observation in vacuum arcs. The anode mode transfers when the wall ion current attains a certain magnitude that is independent of the cathode, but dependent on the anode. The ion-current function to the arc current increases when the arc current increases in the diffuse arc. Spectral-line intensity of Cu III emitted from the plasma in the anode region increases with an instantaneous arc current of a 5-kA peak (kAp) sinusoidal half-wave. These findings suggest an idea for the mode transition, that an ion generation region appears, and that an increase in the ion density produces a positive potential hump near the anode, which results in the negative anode voltage drop triggering the mode transition. After the mode transition, an arc current is found to reduce the ion current near the crest of a sinusoidal current in a copper arc. This appears to be significant for the arc on a small anode. The decrease in the ion current is attributed to the recombination of ions decelerated by anode vapor with electrons emitted from the hot spot on the anode     

Self-extraction of negatively charged carriers from anodic vacuumarcs

Measurement and magnetic analysis of self-extracted negatively charged carriers (NCCs) from anodic vacuum arcs are presented. They flow to charge collectors made of stainless steel, which are electrically connected to a cathode. When a 60-Hz sinusoidal arc current of 40 kA is burned on 20-mm-diameter copper electrodes spaced 4 mm apart, a negative current of approximately 900 A flows to a cylindrical collector surrounding the arc. The floating collector potential relative to the cathode is measured, and the mean energy of the NCCs is estimated to be greater than 40 eV. It is difficult for the NCCs to flow from anodic vacuum arcs when an anode is made of zinc or cadmium, the atoms of which have electron affinities of less than 0 eV. A magnetic filter of about 500 G, which is placed between the arc and a 30-mm-diameter circular collector, does not affect the NCC's flow from a 4-kA arc burned on copper electrodes. It is possible to extract a large amount of negative copper ions from the anodic copper vacuum arcs     

Mechanism of ion flow generation in vacuum arcs

The ecton model of the cathode spot is used to analyze the main parameters of ion flow in vacuum arcs (ion erosion, mean charge, and velocity). It is shown that the arc plasma is formed as a result of microexplosions at the cathode surface, induced by the Joule heating by the high-density current of explosive electron emission. Ionization processes are localized in a narrow region of the order of a micrometer near the cathode and the ionization composition of the plasma subsequently remains unchanged. Under the action of the electron pressure gradient, ions acquire directional velocities of the order of 10⁶ cm/s even over small distances of the order of several micrometers.     

A Review of Anode Phenomena in Vacuum Arcs

This paper discusses are modes at the anode, experimental results pertinent to anode phenomena, and theoretical explanations of anode phenomena. A vacuum are can exhibit five anode discharge modes: (1) a low current mode in which the anode is basically passive, acting only as a collector of particles emitted from the cathode; (2) a second low current mode that can occur if the electrode material is readily sputtered (a flux of sputtered atoms will be emitted by the anode); (3) a footpoint mode, characterized by the appearance of one or more small luminous spots on the anode (footpoints are generally much cooler than the true anode spots present in the last two modes); (4) an anode spot mode in which one large or several small anode spots are present (such spots are very luminous, have a temperature near the atmospheric boiling point of the anode material, and are a copious source of vapor and ions); and (5) an intense are mode where an anode spot is present, but accompanied by severe cathode erosion. The are voltage is relatively low and quiet in the two low current modes and the intense are mode. It is usually high and noisy in the footpoint mode, and it can be either in the anode spot mode. Anode erosion is low, indeed negative, in the two low current modes, and it is low to moderate in the footpoint mode. Severe anode erosion occurs in both the anode spot and intense are modes. The dominant mechanism controlling the formation of an anode spot appears to depend upon the electrode geometry, the electrode material, and the current waveform of the particular vacuum are being considered. In specific experimental conditions, either magnetic constriction in the gap plasma, or gross anode melting, or local anode evaporation can trigger the transition. However, the most probable explanation of anode spot formation is a combination theory, which considers magnetic constriction in the plasma together with the fluxes of material from the anode and cathode as well as the thermal, electrical, and geometric effects of the anode in analyzing the behavior of the anode and the nearby plasma.     

Anode-Spot Formation and Motion of Vacuum Arcs

This paper reports about experimental investigations on high-current vacuum-arc phenomena, especially anode-spot formation, arc states, and motion. The presented work was stimulated by lack of information about the transition process from the diffuse low-current mode to the high-current mode characterized by anode spot(s). Optoelectronic measurements, streak photographs, high-speed movies, and correlated arc voltage/current records yielded remarkable results on power-frequency vacuum arcs. Three different high-current vacuum arc modes can be observed beyond a certain threshold current. Which mode appears depends mainly on the momentary electrode distance. The modes are characterized by different anode-spot behavior and interelectrode phenomena. The transition between different arc modes is continuous. The arc modes observed on ring electrodes producing a magnetic blast field are the same as those appearing on butt-type electrodes. Anode-spot formation is preceded by congregations of cathode spots and may be initiated by thermal overload of the anode surface opposite to these cathode-spot clusters.     

Dielectric Recovery of Vacuum Arcs after Strong Anode Spot Activity

Recovery of dielectric strength and post-arc currents after diffuse and constricted vacuum arcs were measured for filat OFHC-Cu contacts (D = 25 mm, d = 7.5 mm) enclosed in a bakable UHV chamber. The arc current pulse had a trapezoidal shape of 5.5-ms duration with peak values up to 11 kA. In comparison with the fast recovery of diffuse arcs, the recovery of constricted arcs with gross melting is considerably retarded. Post-arc currents are simulated using the Andrews-Varey model extended to include the effects of secondary electron emission due to ion bombardment of the cathode and loss of the plasma due to thermal motion. The flow of charge carriers to the anode and the shield, which is at the anode's potential, are registered separately. The amount and decay of the residual plasma is evaluated from the measurements of post-arc current. The decay times of a few tens of a microsecond give evidence of ions with energies below 1 eV. The origin and effect of slow ions on recovery is discussed.     

Burning Voltage in Atmospheric and Vacuum Short Arcs of Vanishing Length

The stepwise increase of the burning voltage of short break arcs has been found not only in a gas but also in vacuum. It is suggested that the effect is associated with the occurrence of a positive anode fall which enhances ionisation phenomena near the anode. This view is supported by the simultaneous registration of arc current, burning voltage, light emission from the anode region, of spectral lines of ions, atoms and continuum from the near anode plasma. The phenomena occur beyond a critical gap distance which can be related to the characteristic geometry of the discharge.     

Cathode spot dynamics on pure metals and composite materials inhigh-current vacuum arcs

An investigation has been carried out of cathode spot dynamics in a triggered vacuum arc in a demountable chamber. A rectangular current pulse of 1-5 kA, 1-5 ms has been used. Sufficient statistics were collected. The expansion of a cathode spot ring on a clean, pure metal surface was corroborated to be a retrograde movement in the self-magnetic field which obeys the same law as the movement of a single spot in an external magnetic field. The influence of a contact gap of 0.5-8 mm and current on the dynamics of cathode spots was investigated. The gap dependence of the proportional coefficient between the spot velocity and magnetic field in the case of a pure copper cathode was obtained. A phenomenon was discovered, where a group of cathode spots form in the short arcs on the CuCr cathodes after a transition diffuse arc stage. The follow-up investigation revealed that a close interrelation exists between the cathode and anode processes in short arcs. This interrelation is responsible for the appearance of the discovered phenomenon. Short-circuit performance tests conducted for a commercial vacuum interrupter proved cathode spot group formation to be responsible for the interruption failure at short contact gaps     

Vacuum breakdown on metal surfaces

The unipolar arc model is described. Experimental proof that unipolar arcing represents a discharge form which easily leads to explosive plasma formation is provided. Using a laser-produced plasma, it has been demonstrated that unipolar arcs ignite and burn on a nanosecond time scale without any external electric field being applied. Similar unipolar arc craters have been observed on the cathode surface of a pulsed vacuum diode with an externally applied field of 0.5 MV/cm. The experimental results show that cathode spots are formed by unipolar arching. The localized buildup of plasma above an electron-emitting spot naturally leads to a pressure gradient and electric field distribution which drives the unipolar arc. The high current density of a unipolar arc provides explosive plasma formation