周期性极化铌酸锂波导全光开关特性分析

从理论方面研究了基于和频与差频级联二阶非线性效应的周期性极化铌酸锂波导全光开关的特性,给出了耦合模方程在满足相位匹配条件下小信号近似的解析表达式.用数值方法求解耦合模方程,讨论了相位失配情况下输出的信号光功率与控制光功率的关系.分析了全光开关器件的极化反转光栅周期、晶体温度、控制光波长等参量的容差特性与相互作用长度和晶体温度的关系 关键词： 级联二阶非线性 光开关 准相位匹配 周期性极化铌酸锂     

周期性极化铌酸锂晶体中半非共线型宽带光学参变放大理论研究

基于周期性极化铌酸锂晶体(PPLN)的准相位匹配光参变放大过程,通过倾斜周期极化铌酸锂晶体中极化域(极化光栅)一定角度,实现了介于共线匹配方式和非共线匹配方式之间的一种半非共线型准相位匹配方式,并以该匹配方式下的各光矢量几何关系得出相位匹配曲线,找到在特定抽运光和信号光波长下能获得宽带增益放大的周期极化长度。并研究其极化倾斜角度与温度特性。模拟计算表明,在合适的角度与温度条件下,该方式可以532 nm抽运光抽运的信号光在800 nm和1064 nm处均获得宽带光参变放大。     

准位相匹配铌酸锂波导倍频特性分析与优化设计

用标量有限元方法计算了周期性极化的铌酸锂光波导中模折射率和模场分布,并在计算中引入铌酸锂晶体折射率与温度变化的关系,分析了准位相匹配铌酸锂波导倍频效率与极化反转光栅周期、基频光波长、波导器件温度等关系.理论分析与实验结果符合得很好.在此基础上,分析了波导制作参数与倍频效率、光栅周期与晶体温度,以及温度带宽与光栅通光方向长度等关系,进而对铌酸锂波导倍频器件进行优化设计. 关键词： 铌酸锂 光波导 准位相匹配 有限元     

宽带准连续光纤激光在周期极化铌酸锂中倍频特性的研究

双包层光纤激光器和非线性光学材料(如周期性极化的铌酸锂晶体,PPLN)相结合,开辟了实用性非线性光学器件的一个新领域。研究了准相位匹配周期性极化反转铌酸锂晶体对宽带准连续光纤激光倍频的温度特性和频谱特性。在理论上,从准相位匹配相位失配关系出发,推导了晶体温度与抽运源中心波长的关系以及温度响应带宽,并和已报道实验结果进行了比较,二者符合得很好。此外,还推导了倍频周期极化铌酸锂晶体对抽运基频光源的响应谱线带宽。在实验上,采用长度20mm,极化周期6．5μm,厚度0．5mm的周期极化铌酸锂晶体光纤激光器准连续宽带输出进行了倍频,获得了在不同控制温度下的倍频光光谱,并对此进行了详细分析。     

级联参量振荡产生太赫兹辐射的理论研究

针对光学参量振荡产生太赫兹波转换效率低的缺点, 提出了级联参量振荡产生太赫兹波的新机理以提高转换效率. 以周期极化铌酸锂晶体为例, 对级联参量振荡产生太赫兹波的原理和过程进行了理论研究. 分析了抽运光波长、周期极化铌酸锂晶体极化周期和工作温度对产生一阶、二阶闲频光频率的影响. 推导了三波共线相互作用条件下太赫兹波的增益特性和吸收特性. 计算结果表明, 通过级联参量振荡可以有效提高太赫兹波的转换效率, 并可以得到宽调谐的太赫兹波输出. 基于分析结果, 设计了周期极化铌酸锂晶体级联参量振荡产生高效率、宽调谐、窄线宽、连续太赫兹波的实验. 关键词： 太赫兹波 太赫兹波参量振荡 级联参量振荡     

低阈值单谐振周期极化掺镁铌酸锂光参量振荡器

对基于周期极化掺镬铌酸锂晶体的信号光单谐振光学参量振荡器的输出特性进行了实验研究.讨论了光学参量振荡器谐振腔的腔长、周期极化铌酸锂晶体的通光长度、输出镜的透过率以及抽运光的脉冲宽度对光学参量振荡器谐振阈值的影响.光学参量振荡器的抽运源采用输出波长为1 064 nm的声光调Q Nd:YVO_4激光器,在重复频率为2 kHz、周期极化掺镁铌酸锂晶体的温度为30℃的条件下,光学参量振荡器的振荡阈值仅为48 mW.当抽运功率为94 mW时获得了25 mW的信号光输出,其光-光转换效率为26.6%.     

低阈值单谐振周期极化掺镁铌酸锂光参量振荡器

对基于周期极化掺镁铌酸锂晶体的信号光单谐振光学参量振荡器的输出特性进行了实验研究.讨论了光学参量振荡器谐振腔的腔长、周期极化铌酸锂晶体的通光长度、输出镜的透过率以及抽运光的脉冲宽度对光学参量振荡器谐振阈值的影响.光学参量振荡器的抽运源采用输出波长为1 064 nm的声光调Q Nd∶YVO4激光器,在重复频率为2 kHz、周期极化掺镁铌酸锂晶体的温度为30 ℃的条件下,光学参量振荡器的振荡阈值仅为48 mW.当抽运功率为94 mW时获得了25 mW的信号光输出,其光-光转换效率为26.6%.     

基于准相位匹配产生近中红外波段的特性分析

基于周期极化晶体的Sellmeier方程和准相位匹配理论,对准相位匹配光参变振荡器的调谐特性进行了理论分析.通过数值模拟计算,得到了PPRTA晶体光参变振荡的调谐特性与极化反转光栅周期、晶体温度和抽运光波长等参量的关系曲线.并且与PPKTP晶体和PPLN晶体光参变振荡器的调谐特性进行了比较,研究了三者的不同之处,得出了PPRTA晶体的参量调谐特性优于PPKTP晶体和PPLN晶体的结论,与国外已报道的实验数据相吻合.证实了PPRTA晶体是一种可以产生可调谐近中红外光的理想准相位匹配非线性光学晶体.     

周期极化铌酸锂THz波产生理论分析

首先采用光参量振荡的机理研究了THz波在准相位匹配媒质周期极化铌酸锂晶体中同向传播与反向传播情况下,以及THz波从晶体表面辐射产生的特性;其次研究了THz波的温度调谐特性、极化反转光栅周期调谐以及改变入射泵浦光与光栅波矢夹角的调谐特性;然后分析了THz波谱宽特性,给出解析表达式,并与实验结果进行了比较,证明理论分析结果与Y.S.Lee等人所给出的实验结果符合很好;最后分析了THz波的稳定性与温度、光栅周期、泵浦入射角以及辐射角的关系.     

1.5μm波段基于级联二阶非线性的铌酸锂光波导全光波长变换的理论分析

研究了基于级联二阶非线性的铌酸锂波导全光波长变换器的特性.首先从耦合模方程出发,比较了数值分析结果与小信号近似分析的结果.其次在数值分析基础上,分析了铌酸锂晶体的温度变化导致相应基频光波波长与极化反转光栅周期的变化关系.最后分析了在不同相互作用长度下,转换的光波功率与有效基频光波波长带宽、温度调谐带宽、极化反转光栅周期带宽等关系,以对全光波长变换器件进行优化设计 关键词： 级联二阶非线性 波长变换 准位相匹配 铌酸锂光波导     

周期极化KTP晶体光参量振荡特性研究

基于较新的Sellmeier方程,研究了周期极化钛氧磷酸钾(KTiOPO₄简称KTP)晶体光参量振荡的容差特性,给出了极化反转光栅周期、晶体温度及泵浦光波长的调谐曲线和带宽的容差特性曲线,并与PPLN晶体作了比较数值计算结果与已有实验数据吻合较好.     

Continuous-wave singly resonant optical parametric oscillator based on periodically poled RbTiOAsO(4)

We report a continuous-wave optical parametric oscillator (OPO) based on periodically poled RbTiOAsO(4) (PPRTA). The singly resonant OPO, which is located within a Ti:sapphire laser, has a high-finesse signal cavity and delivers a maximum output power of 270 mW to the nonresonant idler wave at 2.92mum , through a 4.5-mm PPRTA crystal. For room-temperature operation and a crystal with a 30-mu;m grating period, pump tuning over 838-848 nm results in OPO tuning over 1.13-1.27mum (signal) and 2.53-3.26mum (idler), limited by the bandwidth of optical coatings. PPRTA exhibits thermal properties superior to those of periodically poled LiNbO(3) .     

非共线准相位匹配周期极化RbTiOAsO4的增益带宽

研究了非共线准相位匹配过程中,周期极化RbTiOAsO_4晶体同时满足准相位匹配和群速匹配条件的非共线角和相应的极化周期随信号光波长的变化。分析了满足群速匹配条件时,非共线准相位匹配的调谐特性。数值模拟了增益带宽随非共线角、晶体温度和极化周期的变化关系。对比了群速匹配和最大增益带宽情况下,周期极化RbTiOAsO_4晶体增益带宽与晶体温度之间的关系。     

低阈值温度调谐PPMgLN红外光参量振荡

研究了温度调谐下周期极化镁掺杂铌酸锂晶体的红外光参量振荡特性。采用外电场短脉冲极化技术,在大小为7.0mm×50.0mm×1.0mm的Z切高镁掺杂(摩尔分数0.05)铌酸锂上制备出了准相位匹配光学微结构器件,极化周期为30.0μm。以输出波长为1064nm的声光调QNd:YAG固体激光器作为基频泵浦光开展了光参量振荡研究。实验表明:泵浦该PPMgLN晶体,实现了室温下低阈值红外光参量振荡产生,阈值功率仅为45mW(重复频率1kHz)。在泵浦输入功率为225mW时,有36mW信号光输出,转换效率达到16.0%,通过调谐晶体温度(20~180℃),获得了调谐范围为1503~1550nm波段的OPO信号光,实现了低阈值可调谐红外光的稳定输出。     

ZnGeP2 parametric oscillator pumped by a linewidth-narrowed parametric 2 microm source

A tandem optical parametric oscillator (OPO) is used to convert radiation from 1.064 microm to the mid-infrared. Spectral bandwidth narrowing close to 80 times compared with a conventional cavity was achieved by using a bulk Bragg grating as an outcoupler in a near-degenerate periodically poled KTiOPO(4) OPO. The narrowed 2,008 nm radiation was subsequently used for pumping the ZnGeP(2) OPO, which was tunable between 3.3 and 5.2 microm. Pulse energies of 170 microJ and pump depletion close to 70% were obtained in the ZnGeP(2) OPO. To our knowledge this is the first time the output from a near-degenerate type I PPKTP OPO has been used for ZnGeP(2) OPO pumping.     

Widely tunable, high-repetition-rate, dual signal-wave optical parametric oscillator by using two periodically poled crystals

This paper reports on a high-repetition-rate dual signal-wave (DSW) optical parametric oscillator (OPO) operating at the 1.5 μm band with tunable wavelength intervals from 2.5 nm to 69.1 nm. Two periodically poled crystals, a periodically poled lithium niobate (PPLN) with multiple gratings and a single grating MgO-doped PPLN (PPMgOLN), are cascaded in the same OPO cavity to generate dual signal-waves by using quasi-phase-matched (QPM) technique. The pump source was a Q-switched diode-pumped Nd:YVO₄ laser operating at 50 kHz. At an incident pump power of 3 W, an average output power of 169.6 mW at 1489.2 nm and 1558.3 nm has been achieved.     

Synchronously pumped femtosecond optical parametric oscillator of congruent and stoichiometric MgO-doped periodically poled lithium niobate

A synchronously pumped femtosecond optical parametric oscillator based on congruent MgO-doped periodically poled lithium niobate (c-MgO:PPLN) is reported. The system, operating at room temperature, was pumped by a mode-locked Ti:sapphire laser. The wavelengths of the signal and idler waves were tuned from 870 nm to 1.54 μm and 1.58 to 5.67 μm, respectively, by changing the pump wavelength, the grating period or the cavity length. Pumped by 1.1 W of 755 nm laser radiation, the OPO generated 310 mW of 1080 nm radiation. This signal output corresponds to a total conversion efficiency of 50%. Without dispersion compensation the OPO generated phase-modulated signal pulses of 200 fs duration. Besides the OPO of c-MgO:PPLN, an OPO of stoichiometric (s) MgO:PPLN was investigated. Because of the reduced sensitivity to photorefractive damage, both crystals allowed efficient OPO operation at room temperature. Received: 19 August 2002 / Revised version: 11 December 2002 / Published online: 19 March 2003 RID="*" ID="*"Corresponding author. Fax: +49-631/205-3906, E-mail: andres@physik.uni-kl.de     

Broadband non-collinear double QPM optical parametric amplification in mid-infrared wave

The properties of optical parametric amplification (OPA) based on non-collinear double quasi-phase matching (NDQPM) with single periodically poled KTP (PPKTP) have been investigated theoretically. The NDQPM includes two different non-linear processes: one is optical parametric generation (OPG) and the other is difference frequency generation (DFG). The investigation of our numerical simulation focuses on the gain bandwidth of dependence upon non-collinear angle, grating period and crystal temperature. At a certain non-collinear angle and grating period with fixed temperature, there exists a broadest gain bandwidths of output mid-infrared pulse at 526 nm pump wavelength and certain signal wavelength in PPKTP. These are an optimal values of non-collinear angles and grating period. By accurately tuning the non-collinear angle or temperature near the optimal non-collinear angle, broadband mid-infrared tuning is obtained and an optimal operation of NDQPM can be realized. In this paper, the solutions of the coupled equations of the cascaded processes were discussed, and the spatial-temporal frequency (STF) band of the output idler pulse is analyzed by taking angular dispersion of amplified pulse beam into account. The idler pulse with a certain angular dispersion can improve the OPA bandwidth significantly. So, optical parametric chirped-pulse amplification can be realized in this configuration. For a broadband NDQPM both the acceptance angles and the acceptance temperature are smaller and the gain bandwidth is sensitive to non-collinear angles and temperature, it is important to control the precision of the non-collinear angles and the temperature in experiment.     

双共振准相位匹配光学参量振荡器的调谐特性

利用全固化单频Nd：YVO4激光器泵浦双共振难相位匹配铌酸锂连续光学参量振荡器，实验研究了该光学参量振荡器下转换光的调谐特性。通过改变PPLN晶体的温度及OPO的腔长，下转换光的调谐范围分别为189nm和175nm，通过改变泵浦光频率，信号光频率连续调谐375MHz。实验结果与理论计算值基本吻合。