一些高Tc超导体的弹性性质

 本文用超声相比较方法测定了高T_c超导体La_1.85Sr_0.15CuO₄，La₂CuO₄和YBa₂Cu₃O₇的纵波和横波声速，进而导出了它们的纵向模量、切变模量、杨氏模量、泊松比、德拜温度及定体比热。在La_1.85Sr_0.15CuO₄样品上，还进行了压力实验，发现所有弹性模量都是随压强增加而增加。定体比热c_V和泊松比σ在高压下则略有下降。德拜温度是随压强增加而增加的。     

TC4、16Mn合金及Al2O3陶瓷的高温弹性模量

 用脉冲回波法测量了TC4、16Mn、Al₂O₃陶瓷从室温到1 000 ℃的纵波与横波声速，由声速得到绝热弹性模量。给出了E、G随温度变化的回归方程。对材料熔点做了估算。     

立方晶体超声物态方程弹性参数的高压测量

 用超声脉冲回波重合技术（PEO），在0.1~500 MPa流体静压力范围，测量了立方晶体Si和Bi₁₂GeO₂₀中沿[100]、[110]和[111]方向传播的纯纵波和切变波自然声速值随压力的变化。根据有限形变理论，由声速与压力关系的实验结果。确定了立方晶体Si和Bi₁₂GeO₂₀超声物态方程的弹性参数（含三阶和四阶弹性常数）。     

高压下材料弹性声速的一种经验表达式

 将铝、铁、铜等七种材料弹性声速的实测数据进行分析处理发现，其弹性声速随压力的变化均可以用一下关系：ln c=A₀+A₁ln p+A₂ln²p，很好的拟合。拟合结果与实测值的相对误差小于5%。     

钨合金的超声测量及力学参量估算

 利用两面顶压机和六面顶压机作为压力装置，分别对93钨合金材料进行了高压超声测量。测得了93钨合金材料在常态下的横、纵波声速及在0~3 GPa压力范围内的纵波声速随压力的变化关系。测量结果为：在常温常压下，93钨合金的纵波声速为c_L＝5.135 km/s，横波声速为c_t＝2.987 km/s。纵波声速随压力变化的关系式为：c_L＝5.053+0.602p（GPa）。估算的93钨合金相关力学参量为：G＝157.4 GPa，E＝393.0 GPa，K＝260.2 GPa，λ＝155.3 GPa，μ＝157.4 GPa，ν＝0.248。经过对两种超声测量方法测量结果的比较及冲击波测量数据的验证，这些参数是可靠的。     

流体静高压原位磁测量的误差研究（二）──退磁场的影响

 为了探讨流体静高压原位磁测量中退磁场的影响有多大？分别选用6种不同片数（n＝1、3、5、7、10、13）的非晶Fe_46.3Co_0.03Ni_46.5Si_3.75V_0.92B_2.5合金薄带样品，先后放进13层密绕直螺线管初级线圈内，采用工业频率400 Hz去测量和比较其磁化曲线、磁导率曲线和起始磁化曲线。研究表明：（1）样品片数越多，退磁场的影响越大，导致μ_m和μ_i出现惊人的测量误差，以1片（μ_m＝4 430，μ_i＝3 396）为最准。（2）随着样品片数的增多，测量饱和磁感应强度B_s＝0.837～0.762T，表明受退磁场影响较小。（3）若要减小退磁场误差，可将样品做得更薄，如0.2 μm薄膜。（4）若要彻底消除退磁场误差，必须采用闭合磁路，如用非晶合金薄带卷成的圆环。     

LaOBr:Tb3+，Dy3+的发光特性及高压研究

 采用高温常压方法合成了稀土发光材料LaOBr:Tb³⁺，Dy³⁺，采用高温高压方法对材料进行了处理，研究了高温高压处理前后样品发光特性的变化，并进行了发光衰减测量。结果表明，Dy³⁺的掺杂可以将Tb³⁺的⁵D₃能级的激发能有效地驰豫到⁵D₄能级，从而使⁵D₄~⁷F_J（J＝0, 1,…,6）的发射，尤其是⁵D₄~⁷F₅的发射明显增强，使得样品的发光亮度大大提高。Dy³⁺，Tb³⁺间存在交叉驰豫共振能量传递。高压处理过程引入的杂质、材料氧化及压致晶场变化都对材料的发光特性产生影响。     

93W合金有关力学参量的综合选评

 对93W合金材料进行了超声测量实验，并结合原有的超声测量结果进行了分析比较，提出了可以直接用冲击波速度关系式的三个系数c₀ 、λ和λ′来对钨合金的有关力学参量，如G₀、K₀、G₀′、K₀′等进行综合选评的方法。得到了一组对93W合金较为合理的力学参量推荐值。     

MgCNi3超导体在静水压下的弹性性质

 在0.1 MPa到0.5 GPa压力范围内，采用脉冲回波重合法（Pulse-Echo Overlap Method）测量了MgCNi₃超导体的横波及纵波声速，计算了体弹模量B、剪切模量G等弹性参数以及德拜温度、比热等热力学参数随压力的变化。常压下的θ_D与c_V的值分别为454.82 K和111.30 J/(mol·K)。对B-p曲线作线性拟合，得到体弹模量B₀在零压附近的导数B′₀，由此建立了MgCNi₃的状态方程。     

0212型Ca3Cu2O4+δCl2-y化合物高温高压合成与研究

 利用“顶角氧掺杂”机制，即以二价氧部分替代顶角一价氯，用Ag₂O做氧源，在高温高压下制备了单相的Ca₃Cu₂O_4+δCl_2-y样品。X射线衍射分析发现，随着Ag₂O含量的增加，Ca₃Cu₂O_4+δCl_2-y样品的晶格常数a逐渐变小，c逐渐增大，体现了空穴掺杂的本质。进行了电阻率和磁化率测量，没有发现超导性，可能是空穴载流子没有达到合适的浓度所致。     

加氢催化剂中稀土及钼、钴含量的X-射线荧光光谱测定方法的研究

使用X 射线荧光光谱仪 ,采用人工合成标样 ,粉末直接压片和经验系数校正基体效应的方法 ,建立了加氢催化剂中稀土氧化物及氧化钼、氧化钴含量的测定方法。研究了制样方法、光谱条件 ,讨论了元素间的相互影响。测定范围MoO3:7%～ 13% ,CoO :2 %～ 7% ,RE2 O3:3%～ 6 %。该方法不仅快速、简便 ,而且准确度和精密度较好 ,在上述范围内 ,测定各元素的RSD均小于 2 %。此方法已用于大量样品的分析 ,测定结果与其他方法相符。     

Ultrasonic Study on Jahn-Teller Distortions in La1=3Sr2=3CoO3

系统研究了La1=3Sr2=3CoO3单相多晶样品在低温下的电磁输运性质和超声特性．电阻率测量表明,La1=3Sr2=3CoO3在整个温区内都表现出金属特性,并且在235 K处电阻率-温度曲线的斜率发生了变化,同时伴随着铁磁相变．超声声速在铁磁相变温度以下出现软化,并在120 K附近达到最小,之后,随着温度的进一步降低,声速开始硬化,同时出现了一个宽大的超声衰减峰．分析认为,该超声异常可能起源于中等自旋态Co3+的Jahn-Teller效应．     

锂离子电池掺钴正极材料电子结构的DV-Xα研究

采用原子基表示的第一原理赝势方法 ,计算了正极材料LiMn2 O4的电子结构 ,发现LiMn2 O4的价带主要是由Mn(8)和Mn(9)的 3d轨道和O(7)、O(6 )、O(4 )的 2p轨道构成 ,导带主要是由Mn(8)和Mn(9)的 3d轨道和O(7)的 2 p轨道构成 .通过计算Li5Mn7CoO8的电子结构 ,发现在LiMn2 O4中用钴离子取代 16d位锰离子将使电极材料的费米能减小 ,放电电压降低 ;锂离子的净电荷增大 ,锂离子与氧离子的相互作用增强 ,可逆容量降低 ;同时由于价带宽度变窄 ,Co-O键间的相互作用比Mn -O键间的相互作用强 ,所以 ,结构稳定性增加 ,电极循环性能改善 .     

A Wavelet-Based Processing method for simultaneously determining ultrasonic velocity and material thickness

Methods of measuring ultrasonic wave velocity in an elastic sample require data on the thickness of the sample and/or the distances between the transducers and the sample. The uncertainty of the ultrasonic wave velocity measurements generally depends on that of the data available. Conversely, to determine the thickness of a material, it is necessary to have a priori information about the wave velocity. This problem is particularly hard to solve when measuring the parameters of biological specimens such as bones having a greater acoustical impedance contrast (typically 3-5 MRayl) than that of the surrounding soft tissues (typically 1.5 MRayl). Measurements of this kind cannot easily be performed. But obtaining the thickness of a bone structure and/or the ultrasonic wave velocity is a important problem, for example, in biomechanical field for the calculation of elastic modulus, or in acoustical imaging field to parameterize the images, and to reference the grey or color level set to a physical parameter.The aim of the present study was to develop a method of simultaneously and independently determining the velocity of an ultrasonic wave in an elastic sample and the wave path across the thickness of this sample, using only one acquisition in pure transmission mode. The new method, which we have called the “Wavelet-Based Processing” method, is based on the wavelet decomposition of the signals and on a suitable transmitted incident wave correlated with the experimental device, and the mathematical properties such as orthonormality, of which lend themselves well to the time-scale approach. By following an adapted algorithm, ultrasonic wave velocities in parallelepipedic plates of elastic manufactured material and the apparent thicknesses were both measured using a water tank, a mechanical device and a matched pair of 1 MHz ultrasonic focused transducers having a diameter of 3 mm, a focal length of 150 mm and beam width of 2 × 2 mm at the focus (mean temperature 22°). The results were compared with those obtained with a conventional Pulse-mode method and with the control values, to check their validity. Measurements performed on bovine and human dry cortical bone samples are also presented to assess the limitations of the method when it is applied to elastic biological samples, including those of an equal-wavelength size (≈1.5 mm). The thicknesses and the ultrasonic wave velocities were then measured in this kind of (quasi-) parallelepipedic elastic materials with an mean estimated error ranged from 1% to 3.5% compared to the referenced values.     

Measurement of hydroxyl radical production in ultrasonic aqueous solutions by a novel chemiluminescence method

Measurement methods for ultrasonic fields are important for reasons of safety. The investigation of an ultrasonic field can be performed by detecting the yield of hydroxyl radicals resulting from ultrasonic cavitations. In this paper, a novel method is introduced for detecting hydroxyl radicals by a chemiluminescence (CL) reaction of luminol-hydrogen peroxide (H2O2)-K5[Cu(HIO6)2](DPC). The yield of hydroxyl radicals is calculated directly by the relative CL intensity according to the corresponding concentration of H2O2. This proposed CL method makes it possible to perform an in-line and real-time assay of hydroxyl radicals in an ultrasonic aqueous solution. With flow injection (FI) technology, this novel CL reaction is sensitive enough to detect ultra trace amounts of H2O2 with a limit of detection (3sigma) of 4.1 x 10(-11) mol L(-1). The influences of ultrasonic output power and ultrasonic treatment time on the yield of hydroxyl radicals by an ultrasound generator were also studied. The results indicate that the amount of hydroxyl radicals increases with the increase of ultrasonic output power (< or = 15 W mL(-1)). There is a linear relationship between the time of ultrasonic treatment and the yield of H2O2. The ultrasonic field of an ultrasonic cleaning baths has been measured by calculating the yield of hydroxyl radicals.     

钴基掺杂氧化物结构特征的研究

利用溶胶-凝胶(sol-gel)法制备出了一系列La0.8Sr0.2Co1-xFexO3样品.xRD结果显示,在La0.8Sr0.2Co1-xFexO3系列样品中,未掺杂的La0.8Sr0.2CoO3样品具有很好的单相结构,并且衍射峰没有发生劈裂;而Fe掺杂的La0.8Sr0.2CoO3样品中几乎每个衍射峰都发生了劈裂,在Fe掺杂的La0.8Sr0.2CoO3样品中可能存在两种不同的晶体结构.利用xANES研究了La0.8Sr0.2Co1-xFexO3样品中Co离子和Fe离子的化合价发现,Fe离子存在两种不同的化合价态,即Fe3+和Fe4+离子,在La0.8Sr0.2Co1-xFexO3样品中形成了两个不同离子的富集区,一个是由Co3+、Co4+和Fe3+等离子组成的,一个是由Fe4+和Co3+、Co4+等离子组成的,因此在Fe掺杂的La0.8Sr0.2CoO3样品中存在两种不同的晶体结构.     

Cu位La、 Gd掺杂YBa2Cu3O7-δ结构和磁通钉扎的比较

多晶样品YBa2Cu3-xLaxO7-δ(0≤x≤0.15)和YBa2Cu3-xGdxO7-δ(0≤x≤0.15)通过固相反应法制备得来.通过结构参数分析,我们发现La首先替代Cu(1)位,然后开始部分替代Ba,而Gd开始替代Cu(2)位然后替代Cu(1)位.YBa2Cu3-xLaxO7-δ和YBa2Cu3-xGdxO...     

YBa_2Cu_3O_(7-x)对氧的检测灵敏度和响应速度

研究了高温超导体 YBa2 Cu3O7- x块材和厚膜在温度区间 40 0℃到 85 0℃电阻率随环境氧分压的变化关系 ,初步探索了其作为氧传感器材料的可能性。并研究了 YBa2 Cu3O7- x在不同温度条件下对氧的检测灵敏度和响应速度。实验表明 YBa2 Cu3O7- x对氧有较强的选择性 ,同一温度下电阻率随氧分压的增大而减小 ,且有较快的响应速度。氧分压减小时电阻率增大 ,块材响应速度较慢 ,但是制成厚膜后可提高其响应速度     

Determination of crystallographic orientation of large grain metals with surface acoustic waves

A previously described laser ultrasonic technique known as spatially resolved acoustic spectroscopy (SRAS) can be used to image surface microstructure, using the local surface acoustic wave (SAW) velocity as a contrast mechanism. It is shown here that measuring the SAW velocity in multiple directions can be used to determine the crystallographic orientation of grains. The orientations are determined by fitting experimentally measured velocities to theoretical velocities. Using this technique the orientations of 12 nickel and 3 aluminum single crystal samples have been measured, and these are compared with x-ray Laue backreflection (LBR) measurements with good agreement. The root mean square difference between SRAS and LBR measurements in terms of an R-value is less than 4.1°. The influence of systematic errors in the SAW velocity determination due to instrument miscalibration, which affects the accurate determination of the planes, is discussed. SRAS has great potential for complementary measurements or even for replacing established orientation determination and imaging techniques.