水声共形阵辐射指向性计算方法及其实验验证

用边界元方法,给出了水声发射换能器共形阵各阵元的单元指向性以及基阵的自然波束指向性和束控波束指向性。首先建立了换能器共形阵的边界元模型,并根据换能器结构和声传播介质建立了模型的边界条件,计算了其辐射指向性。然后在消声水池中对共形阵各阵元以及基阵的辐射指向性进行了实验测量。将理论计算结果与实验测量结果进行了对比,二者吻合得比较好。研究结果表明:基于边界元方法建立的模型及计算方法,对基阵的辐射指向性进行理论计算和预报是可行的。     

水下应用的电容式微机械超声换能器阵列设计

为提高用于水下成像的电容式微机械超声换能器的指向性,文中用ANSYS力电耦合分析法设计了工作频率为400 k Hz的收发一体传感器的结构参数并完成了实验验证。同时研究了阵列设计方法,分析了电容式微机械超声换能器阵列各参数对指向性的影响,完成了从微小敏感单元到阵列的设计,实现了阵列指向性的优化设计。该阵列为16阵元的线阵,阵元间距为1.925 mm,阵元宽度为1.82 mm。进行了水下指向性测试,实验表明该线阵的-3 dB主瓣宽度为5?,最大旁瓣级为-13.5 dB,对称性好。该设计是实现较远距离的探测,提高成像分辨率的前提。     

离散多基元声基阵指向性函数计算

本文从任意分布的离散多基元点阵的指向性函数,引出线列阵、圆弧阵、平面阵、圆柱阵以及球面阵、共形阵的指向性函数。并且进一步阐述了它们的波束形成和波束空间复盖方案设计。     

论阵形畸变的拖曳式线列阵的工作方式的选取问题

阵形畸变是拖曳式线列阵声呐性能偏离理想情况的主要原因。本文讨论在常见阵形畸变方式下,线列阵指向性的计算。给出在各种不同参数下求解椭圆反函数以确定每个基元的精确坐标的方法。同时给出一种递推的公式,用于快速求解畸变阵的阵形。根据对畸变阵指向性与理想指向性的比较,提出拖曳式线列阵的工作方式选取的准则。从而解决了拖曳式线列阵声呐性能预报这一课题。计算机模拟结果与理论分析完全一致。     

刚性圆柱体上圆阵波束形成性能分析

以环绕在刚性圆柱体上的均匀圆阵为阵列模型,分析了刚性圆柱体对圆阵响应的影响,在声场分解所得到的相位模式空间,推导了相位模式波束形成阵列和延迟求和波束形成阵列的白噪声增益和指向性指数的定量表达式,分析了它们在不同频率段的变化规律。在存在和不存在刚性圆柱体两种情况下,对两种阵列性能进行了对比分析。研究了圆阵与圆柱体之间存在间隙时对阵列接收信号及阵列性能的影响。仿真结果表明,在两种情况下相位模式波束形成处理都具有频率不变的指向性,但在低频段牺牲了阵列的鲁棒性;延迟求和波束形成处理在整个频率段具有较好的鲁棒性,但随频率的降低其波束指向性下降,直至变成各向同性阵列。存在刚性圆柱体时,两种阵列鲁棒性均有了一定的提高,前者的指向性不变,而后者的指向性得到了提高。圆阵与圆柱体之间的间隙会降低阵列在高频段的鲁棒性。      

圆弧阵的水平指向性和综合

本文使用稳相法详细讨论了圆弧阵的水平指向性,给出了计算指向性函数的主瓣束宽和主瓣内平均声压的比较准确的公式。本文提出的幅度束控方法和设计不等距阵方法可以成功地克服圆弧阵主瓣内指向性函数起伏大的缺点,同时使主瓣束宽和主瓣内平均声压基本保持不变。     

稀疏圆柱基阵波束垂直扫描

本文分析了三维圆柱形基阵波束垂直栅瓣形成机理,导出波束垂直扫描极限波长和基阵其他参数的关系,指出指向性函数通常是复数,并用子阵相移法来调节复合子阵的相位特性,在圆环阵指向性图适当位置插入零点,以消除垂直栅瓣、扩大基阵波束扫描范围。对不同基阵,找出相移参数β的最佳值,一般取kβ≈0.5为宜。以两个弧面阵为例作了数值计算,证明对全圆阵导出的极限波长也适用于弧面阵;和相同条件下未相移基阵相比,可将波束垂直扫描范围扩大到间距d为五个波长左右,或将基元数减少2—4倍;当未相移基阵指向性图出现栅瓣时,并可将指向性指数提高1.7到5.5dB。     

宽带密排平面阵声辐射分析

应用声有限元-边界元法计算了宽带基阵声场分布.建立了平面9元阵有限元-边界元模型,给出了阵元之间互阻抗数值计算方法,分析了阵元间互辐射对声性能影响的变化规律,计算了9元阵3个谐振频率点处指向性和波束宽度.利用3谐振换能器研制出一种宽带密排平面9元阵,并在消声水池中对其输入阻抗和指向性进行了实验测量.研究结果表明,按阵元...     

阵元间互辐射对基阵指向性的影响研究及试验

针对常规基阵指向性图计算并未考虑阵元间互辐射阻抗影响这一不足,修正了常规基阵指向性图计算公式。将阵元间的互辐射阻抗引入到水声基阵的辐射声场计算中,并依据叠加原理得到包含阵元间互辐射阻抗的基阵指向性图计算修正公式。15元均匀线列阵和5×5均匀平面阵的计算机仿真和消声水池试验结果表明,该修正公式相比于常规公式更能反映基阵指向性图的真实情况。      

圆柱阵子阵分级处理的稳健超指向性波束形成方法

提出了圆柱阵子阵分级处理的稳健超指向性波束形成方法。首先建立了圆柱阵分两级子阵进行波束形成的信号模型,接着利用空间均匀噪声场中噪声互谱矩阵的循环特性得到基于特征波束分解与综合模型的圆柱阵超指向性的最优解,然后仿真研究了其误差敏感度函数、阵增益和波束图等性能指标,并与圆柱阵的传统全局处理方法进行了对比。提出的分两级子阵处理的超指向性方法与传统全局处理方法相比不仅降低了数据存储量和波束形成计算量,而且进一步提升了稳健性,并且在低频段的阵增益远远高于常规波束形成的值,对水下声呐阵列的设计具有一定的参考价值。      

Influence of component errors on the directivity function of pulsed, ultrasonographic linear arrays

The directivity of linear arrays can deteriorate by reason of component errors such as variations in the sensitivity of the array elements, and variations in the electronic delays applied to synthetic aperture focusing. A prototype 16 channel linear array system has been analysed by calculating the directivity functions corresponding to random-error ensembles in relation to sensitivity and delay. With state-of-the-art components, the main lobe of the directivity function is hardly influenced, but the tails of the function show stronger variation, and also become asymmetrical.     

Non-contact optical fibre phased array generation of ultrasound for non-destructive evaluation of materials and processes

The use of non-contact laser techniques for the generation of ultrasound has extended the limits of the application of traditional ultrasonic techniques. This paper focusses on the use of one such non-contact laser technique, known as ‘optical fibre array’, to generate shear and surface waves. The shear wave experimental directivity pattern results are presented and compared with the theoretical results of a single source and an array source. The experimental directivity results for the surface wave are also presented, and compared with the theoretical results. The data show that the array enhances signal generation in the forward direction for both shear and surface waves. The array gain is also discussed. The receiver for the directivity measurements was a contact piezoelectric transducer.     

Long-Term Horizontal Vocal Directivity of Opera Singers: Effects of Singing Projection and Acoustic Environment

Vocal directivity refers to how directional the sound is that comes from a singer's mouth, that is, whether the sound is focused into a narrow stream of sound projecting in front of the singers or whether it is spread out all around the singer. This study investigates the long-term vocal directivity and acoustic power of professional opera singers and how these vary among subjects, among singing projections, and among vastly different acoustic environments. The vocal sound of eight professional opera singers (six females and two males) was measured in anechoic and reverberant rooms and in a recital hall. Subjects sang in four different ways: (1) paying great attention to intonation; (2) singing as in performance, with all the emotional connection intended by the composer; (3) imagining a large auditorium; and (4) imagining a small theatre. The same song was sung by all singers in all conditions. A head and torso simulator (HATS), radiating sound from its mouth, was used for comparison in all situations. Results show that individual singers have quite consistent long-term average directivity, even across conditions. Directivity varies substantially among singers. Singers are more directional than the standard HATS (which is a physical model of a talking person). The singer's formant region of the spectrum exhibits greater directivity than the lower-frequency range, and results indicate that singers control directivity (at least, incidentally) for different singing conditions as they adjust the spectral emphasis of their voices through their formants.     

cMUT阵元的声学分析与环形扫描成像

电容式微机械超声换能器(cMUT)具有宽带宽、灵敏度高、机械阻抗低和与电子电路集成制造等优点.由于超声换能器声场设计的好坏决定了成像质量的优劣,为了明确阵元参数与辐射声场的关系,该文对不同的阵元参数进行了计算仿真.与压电陶瓷超声换能器的结构不同,cMUT阵元是由多个电容单元(cell)并联构成.因此分析了cell的半径...     

天线方向系数的一类计算逼近方法

天线的方向系数是天线的核心性能指标之一,准确计算方向系数是高性能天线应用的核心要求.本文基于平面近场测试理论、实测数据和快速傅里叶变换算法,系统阐述基于近场测试来数值计算天线方向系数的原理,并进行深入的误差分析.本文选择一种方向图函数和方向系数已知的被测天线,来检验所讨论的误差评估方案.评估分两步实现,第一步,针对这一天线,采用标准的近场测试配置,仿真模拟出(相当于实际测量出)一套平面近场数据.第二步,基于这套近场数据,利用数值积分计算出天线方向系数.本文使用或提出了四种数值算法,分析了提出的后三种算法本身的误差来源,并开发出程序搜索方案,确定出后两种算法的最小误差界.随后,利用这四种数值算法分别得出天线的方向系数.结果表明,计算所得的近场方向系数都比真实方向系数大,但误差不超过0.6 d B.这一结果对实际应用中正确评估基于近场测试的天线方向系数准确性有重要参考价值.     

Influence of source directivity on noise levels in industrial halls: Simulation and experiments

Noise exposure of workers in industrial halls is mainly induced by noisy machines whose acoustical features are often globally known by Sound Pressure Level. The evaluation of the directivity of these noise sources can help to anticipate specific solutions for noise reduction.This study shows how the directivities of three wood-working machines have been characterized. Some characterisations have been achieved with a simple and fast acoustical intensity mapping which meets the constraints of industrial areas.When source directivity is evaluated, its influence on the noise field in industrial halls can be assessed. Some simulations and some experiments allowed the estimation of the noise field induced in workshops by both directional and omnidirectional sources. Comparison of the fields prove that the noise distribution is influenced by the source directivity if the halls are empty. As soon as the halls contain scattering objects, the directivity effect is reduced a lot and the noise field remains nearly the same far from the source whatever source used. Nevertheless, workers close to a machine are exposed to noise according to their position with respect to the machine. Exposure at the workplace can vary from 4 to 8 dB(A) according to the directivity of machines such as those measured in the trials.     

基于分组时延预处理的时域波束形成方法*

对于不等强度多目标情况下的弱目标检测问题,依据波束形成归一化指向性函数在目标方向上输出值为1、在非目标方向上输出值为小于1的特性,提出一种基于分组时延预处理的时域波束形成方法。该方法首先对线列阵接收数据进行分组处理;然后,按搜索角度对各组数据进行时延预处理,并对各组预处理结果进行相加,得到一组新数据;最后,对该组新数据按时域波束形成进行处理,得到该搜索角度对应波束值。理论推导、数值仿真和试验数据处理结果均表明：相比常规时域波束形成,该方法所得波束形成指向性函数发生了变化,旁瓣级得到了13dB以上的改善,降低了强目标旁瓣级对弱目标检测的影响。     

非旋转对称电声器件的指向性因子测量

本文介绍了精确测量非旋转对称电声器件的指向性因子的原理和方法，并根据ＩＥＣ１１８３标准规定的方法，地Ｂ＆Ｋ２２０９声级计指向性因子进行了测量，提供一个非旋转对称装置的指向性因子测量的例子。     

3-D Model of sound pressure field in a meridinal section plane of fruit

A theoretical model was suggested for qualitative evaluation of a sound pressure field in fruit tissue, as affected by ultrasonic probe dimensions and fruit properties. The classic directivity pattern of an ideal fluid model, expressed by Bessel function of the first kind, was extended to include energy dissipation of a real material. The directional characteristics of wave propagation, as influenced by transmitter frequency and diameter, and by fruit properties, were discussed. The model indicates how to select the parameters of the ultrasonic transducer (transducer diameter, frequency and excitation power) to control the magnitude and directivity of the ultrasonic waves in the fruit tissue. The suggested theoretical model represented fairly well the experimental sound wave distribution over the half-cut surface of potato and avocado (R² > 0.862 and 0.977, respectively); the same theoretical model could not represent the sound wave distribution over a half-cut melon. Results of the study were applied in a new probe design for ultrasonic testing of whole fruit.