Characterization of hybrid electrolytes prepared from the Li2S-P2S5 glasses and alkanediols

Inorganic-organic hybrid electrolytes were prepared by the mechanochemical method using the Li⁺ ion conductive 70Li₂S·30P₂S₅ glass and various alkanediols. Local structure of the prepared electrolytes was analyzed by FT-IR and Raman spectroscopy. The effects of the proportion and chain length of alkanediols on conductivity of the hybrid electrolytes were investigated. The hybrid electrolyte with 2 mol.% of 1,4-butanediol exhibited the conductivity of 9.7 × 10^− 5 S cm^− 1 at room temperature and the unity of lithium ion transference number. The use of alkanediols with shorter chain length was effective in increasing conductivity of hybrid electrolytes. The electrolyte using ethyleneglycol showed the highest conductivity of 1.1 × 10^− 4 S cm^− 1 at room temperature. Lowering glass transition temperature by incorporation of alkanediols is responsible for the enhancement of conductivity of hybrid electrolytes.     

Electrical properties vs. microstructure of nanocrystallized V2O5-P2O5 glasses — An extended temperature range study

An electronically conducting nanomaterial was synthesized by nanocrystallization of a 90V₂O₅·10P₂O₅ glass and its electrical properties were studied in an extended temperature range from − 170 to + 400 °C. The conductivity of the prepared nanomaterial reaches 2 ? 10^− 1 S cm^− 1 at 400 °C and 2 ? 10^− 3 S cm^− 1 at room temperature. It is higher than that of the original glass by a factor of 25 at room temperature and more than 100 below − 80 °C. A key role in the conductivity enhancement was ascribed to the material's microstructure, and in particular to the presence of the large number of small (ca. 20 nm) grains of crystalline V₂O₅. The observed conductivity dependencies are discussed in terms of the Mott's theory of the electronic hopping transport in disordered systems. Since V₂O₅ is known for its ability to intercalate lithium, the presented results might be helpful in the development of cathode materials for Li-ion batteries.     

Luminescence spectroscopy of Ti ions in Li2O-CaF2-P2O5 glass ceramics

Li₂O-CaF₂-P₂O₅ glasses mixed with different concentrations of TiO₂ (ranging from 0 to 0.8 mol%) were crystallized at 500 °C. The photo luminescence spectra of these samples excited with the wavelengths corresponding to their absorption edges have been recorded at room temperature. The spectra exhibited an emission band in the wavelength region 470-500 nm. The emission band is identified due to the charge transfer from O²⁻ ion in to empty 3d orbital of octahedrally positioned Ti⁴⁺ ions. The analysis of the results further indicates the highest luminescence efficiency for the glass ceramic sample crystallized with 0.6 mol% of TiO₂.     

Influence of Al2O3 additions on crystallization mechanism and conductivity of Li2O-Ge2O-P2O5 glass-ceramics

The crystallization mechanism and conductivity of lithium aluminum germanium phosphate [LAGP] glass-ceramics fabricated from Li_1+xAl_xGe_2−x(PO₄)₃ (x=0.0-0.7) glass system were investigated as a function of Al₂O₃ additions. A non-isothermal analysis was performed to study the crystallization behavior of LAGP glass-ceramics at various heating rates (5-25K min⁻¹) by the Kissinger equation and the Augis-Bennett equation, illustrating volume crystallization for the glass-ceramics. The crystal identification and microstructure in glass-ceramics containing various Al₂O₃ contents were analyzed by means of XRD and FESEM. The main phase of the glass-ceramics was found to be LiGe₂(PO₄)₃, with AlPO₄ as the impurity phase. Additionally the highest total ionic conductivity (5.8×10⁻⁴ S/cm) at room temperature was obtained when x=0.5 for Li_1+xAl_xGe_2−x(PO₄)₃ (x=0.0-0.7) glass-ceramics, suggesting that it was a promising electrolyte for practical application in all-solid-state lithium batteries.     

Features of the local structural disorder in Li2O-CaF2-P2O5 glass-ceramics with Cr2O3 as nucleating agent

Li₂O-CaF₂-P₂O₅ glasses mixed with different concentrations of Cr₂O₃ (ranging from 0 to 1.0 mol%) were crystallized. The samples were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy (EDS), differential thermal analysis and conventional spectroscopic techniques. The X-ray diffraction and scanning electron microscopic studies reveal the presence of lithium phosphate, calcium phosphate and chromium phosphate (complexes of Cr³⁺, Cr⁵⁺ and Cr⁶⁺ ions) crystal phases. The study on DTA suggests that the crystallization is predominantly due to the surface crystallization when the concentration of nucleating agent Cr₂O₃ is around 0.8 mol%. The IR and Raman spectral studies of these samples indicate that the sample crystallized with 0.8 mol% Cr₂O₃ is more compact and possesses high rigidity due to the presence of chromium ions largely in tetrahedral positions.     

High lithium ion conducting glass-ceramics in the system Li2S–P2S5

Highly ion-conductive Li₂S–P₂S₅ glass-ceramic electrolytes were prepared by controlling the compositions and heat treatment temperatures of the glasses. The 70Li₂S·30P₂S₅ (mol%) glass-ceramic heated at 360 °C showed the highest conductivity of 3.2 × 10^− 3 S cm^− 1 at room temperature and the lowest activation energy of 12 kJ mol^− 1 for conduction in the binary system Li₂S–P₂S₅. The outstanding property was attributed to both the precipitation of the new crystal as a metastable phase and the increase in crystallinity of the phase. With increasing heat treatment temperatures, the metastable phase changed into thermodynamically stable phases such as the Li₄P₂S₆ crystal by heat treatment up to 550 °C, resulting in low conductivities of the glass-ceramics. It was, thus, found that the formation of superionic metastable phases by heating the Li₂S–P₂S₅ glasses is responsible for the marked enhancement on the conducting properties of the glass-ceramics.     

Improvement of electrochemical performance of all-solid-state lithium secondary batteries by surface modification of LiMn2O4 positive electrode

To improve the electrochemical performance of an all-solid-state In/80Li₂S⋅20P₂S₅ (electrolyte)/LiMn₂O₄ cell, a lithium-titanate thin film was used to coat LiMn₂O₄. The interfacial resistance between LiMn₂O₄ and the electrolyte (measured after initial charging) decreased when the LiMn₂O₄ particles were coated with lithium-titanate. A cell with lithium-titanate-coated LiMn₂O₄ had a higher capacity than a cell with noncoated LiMn₂O₄ for current densities in the range 0.064 to 2.6 mA cm^− 2. Additionally, a cell with coated LiMn₂O₄ retained 96% of the 10th-cycle reversible capacity at a current density of 0.064 mA cm^− 2 after 50 cycles.     

Effect of Bi2O3 on EPR, optical transmission and DC conductivity of vanadyl doped alkali bismuth borate glasses

Glasses with composition xBi₂O₃·(30−x)M₂O·70B₂O₃ (M=Li, Na) containing 2 mol% V₂O₅ have been prepared over the range 0≤x≤15 (x is in mol%). The electron paramagnetic resonance spectra of VO²⁺ of these glasses have been recorded in the X-band (≈9.3 GHz) at room temperature (RT≈300 K). Spin Hamiltonian parameters, g_∥, g_⊥, A_∥, A_⊥, dipolar hyperfine coupling parameter, P, and Fermi contact interaction parameter, K, have been calculated. The molecular orbital coefficients, α² and γ², have been calculated by recording the optical transmission spectra. In xBi₂O₃·(30−x)Li₂O·70B₂O₃ glasses there is decrease in the tetragonality of the V⁴⁺O₆ complex for x up to 6 mol% whereas for x≥6 mol%, tetragonality increases. In xBi₂O₃·(30−x)Na₂O·70B₂O₃ glasses there is increase in the tetragonality of the V⁴⁺O₆ complex with increasing x. The 3d_xy orbit expands with increase in Bi₂O₃:M₂O ratio. Values of the theoretical optical basicity, Λ_th, have also been reported. The DC conductivity increases with increase in temperature. The order of conductivity is 10⁻⁵ ohm⁻¹ m⁻¹ at low temperature and 10⁻³ ohm⁻¹ m⁻¹ at high temperature. The DC conductivity decreases and the activation energy increases with increase in Bi₂O₃:M₂O ratio.     

Thermoluminescence of B2O3-Li2O glass system doped with MgO

Lithium borate (LiB) glasses in the system (100−x)B₂O₃-xLi₂O with x=20, 30, 40, 50, 60 and 70 mol% were prepared. The glasses were doped with different concentrations of the order of 10⁻¹, 10⁻², 10⁻³, 10⁻⁴ and 10⁻⁵ of MgO and their thermoluminescent (TL) response was investigated. The irradiations were performed using γ rays from a ⁶⁰Co source in the dose range from 0.1 to 25 kGy. The material displayed good sensitivity for γ-rays and intensity of TL signals is dependent on γ-ray dose and Li₂O content. For each dose level and investigated temperature range (50-350 °C), exactly single isolated glow peak appears in the temperature range of 165-205 °C depending on both Li₂O concentrations and time of exposure. The shape of the glow peak has altered significantly with increase in the gamma ray dose or Li₂O concentrations. The glass composition with x=50 mol% doped with 10⁻³ mol% of MgO presented the best TL response. The results of the present study indicated that the recorded single and isolated high temperature peak is a good candidate for TL dosimetric investigations. This indicates that 50 B₂O₃-50Li₂O-doped with 10⁻³ mol% of MgO is possibly used as materials for radiation dosimetry in the dose range of 0.1-20 kGy.     

Electrical and electrochemical properties of molten salt-synthesized Li4Ti5−xSnxO12 (x=0.0, 0.05 and 0.1) as anodes for Li-ion batteries

Submicron-sized polyhedral Li₄Ti_5−xSn_xO₁₂ (x=0.0, 0.05, and 0.1) materials were successfully prepared by a single-step molten salt method. The structural, morphological, transport and electrochemical properties of the Li₄Ti_5−xSn_xO₁₂ were studied. X-ray diffraction patterns showed the formation of a cubic structure with a lattice constant of 8.31 Å, and the addition of dopants follows Vegard's law. Furthermore, FT-IR spectra revealed symmetric stretching vibrations of octahedral groups of MO₆ lattice in Li₄Ti₅O₁₂. The formation of polyhedral submicron Li₄Ti_5−xSn_xO₁₂ particles was inferred from FE-SEM images, and a particle size reduction was observed for Sn-doped Li₄Ti₅O₁₂. The chemical composition of Ti, O and Sn was verified by EDAX. The DC electrical conductivity was found to increase with increasing temperature, and a maximum conductivity of 8.96×10⁻⁶ S cm⁻¹ was observed at 200 °C for Li₄Ti₅O₁₂. The galvanostatic charge–discharge behavior indicates that the Sn-doped Li₄Ti₅O₁₂ could be used as an anode for Li-ion batteries due to its enhanced electrochemical properties.     

Preparation and mass transport properties of Li2.3Mo6S7.7

Unsuccessful attempts were made to prepare Li_xMo₆S_7.7 by direct ionic exchange of Cu₂Mo₆S_7.7 using aqueous, acetontrille, and molten salt solvents. Li_2.3Mo₆S_7.7 was eventually prepared by lithiation of Mo₆S₈ using n-butyl lithium reagent. The mass transport properties of hot-pressed samples were measured using a four-point dc technique and the following values at 415°C for the lithium ionic conductivity, .4×10⁻⁴ (ohms cm⁻¹) and lithium chemical diffusion coefficient 3.5×10⁻⁷ cm²/s, were derived. A possible explanation for the relatively low lithium ion mobility in Li_2.3Mo₆S_7.7 is discussed.     

Crystallization kinetics of Li2O-PbO-V2O5 glasses

Lead vanadate glasses of the system 5Li₂O−(45−x) PbO−(50+x) V₂O₅, with x=0, 5, 10, and 15 mol% have been prepared and studied by differential scanning calorimetry (DSC). The crystallization kinetics of the glasses were investigated under non-isothermal conditions applying the formal theory of transformations for heterogeneous nucleation to the experimental data obtained by DSC using continuous-heating techniques. In addition, from dependence of the glass-transition temperature (T_g) on the heating rate, the activation energy for the glass transition was derived. Similarly the activation energy of the crystallization process was determined and the crystallization mechanism was characterized. The results reveal the increase of the activation energy for glass transition which was attributed to the increase in the rigidity, the cross-link density and the packing density of these glasses. The phases into which the glass crystallizes have been identified by X-ray diffraction. Diffractograms of the transformed material indicate the presence of microcrystallites of Li_0.30V₂O₅, Li_0.67O₅V₂, LiV₆O₁₅, Li₄O₄Pb, and O₇Pb₂V₂ in a remaining amorphous matrix.     

Photocatalytic H2 evolution under visible light irradiation on AgIn5S8 photocatalyst

A new visible-light-driven photocatalyst AgIn₅S₈ was prepared by a simple two-step process, which involves the first co-precipitation process at room temperature and subsequently heat-treatment process at 750 °C under pure argon flow protection. The obtained AgIn₅S₈ sample showed high activity for the evolution of hydrogen under visible light irradiation (λ?420 nm) from aqueous solution containing S²⁻ and SO₃²⁻ ions as sacrificial electron donors. It was found that several experimental parameters, such as the concentration of sacrificial reagents and the loading of Pt co-catalyst, play important roles on the evolution rate of H₂ under visible light irradiation.     

Effect of Li2O and CoO-doping of CuO/Fe2O3 system on its surface and catalytic properties

Physicochemical, surface and catalytic properties of pure and doped CuO/Fe₂O₃ system were investigated using X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX), nitrogen adsorption at −196 °C and CO-oxidation by O₂ at 80-220 °C using a static method. The dopants were Li₂O (2.5 mol%) and CoO (2.5 and 5 mol%). The results revealed that the increase in precalcination temperature from 400 to 600 °C and Li₂O-doping of CuO/Fe₂O₃ system enhanced CuFe₂O₄ formation. However, heating both pure and doped solids at 600 °C did not lead to complete conversion of reacting oxides into CuFe₂O₄. The promotion effect of Li₂O dopant was attributed to dissolution of some of dopant ions in the lattices of CuO and Fe₂O₃ with subsequent increase in the mobility of reacting cations. CoO-doping led also to the formation of mixed ferrite Co_xCu_1−xFe₂O₄. The doping process of the system investigated decreased to a large extent the crystallite size of unreacted portion of Fe₂O₃ in mixed solids calcined at 600 °C. This process led to a significant increase in the S_BET of the treated solids. Doping CuO/Fe₂O₃ system with either Li₂O or CoO, followed by calcination at 400 and 600 °C decreased its catalytic activity in CO-oxidation by O₂. However, the activation energy of the catalyzed reaction was not much affected by doping.     

Preparation and characterization of Cu(In,Ga)(Se,S)2 films without selenization by co-sputtering from Cu(In,Ga)Se2 quaternary and In2S3 targets

In this study, Cu(In,Ga)(Se,S)₂ (CIGSS) thin films were deposited onto a bi-layer Mo coated soda-lime glass by co-sputtering a chalcopyrite Cu(In,Ga)Se₂ (CIGS) quaternary alloy target and an In₂S₃ binary target. A one-stage annealing process was performed to form CIGSS chalcopyrite phase without post-selenization. Experimental results show that CIGSS films were prepared by the proposed co-sputter process via CIGS (70 W by radio frequency) and In₂S₃ (30 W by direct current) with a substrate temperature of 373 K, working pressure of 0.67 Pa, and one-stage annealing at 798 K for 30 min. The stoichiometry ratios of the CIGSS film were Cu/(In + Ga) = 0.92, Ga/(In + Ga) = 0.26, and Se/(S) = 0.49 that approached device-quality stoichiometry ratio (Cu/(In + Ga) < 0.95, Ga/(In + Ga) < 0.3, and (Se/S) ≈ 0.5). The resistivity of the sample was 14.8 Ω cm, with a carrier concentration of 3.4 × 10¹⁷ cm⁻³ and mobility of 1.2 cm² V⁻¹ s⁻¹. The resulting film exhibited p-type conductivity with a double graded band-gap structure.     

Electrical behaviour of Li2O-ZnO-SiO2 glass and glass-ceramics system

Sealing quality lithium zinc silicate (LZS) glasses of compositions (wt.%) (a) LZSL- Li₂O: 12.65, ZnO: 1.85, SiO₂: 74.4, Al₂O₃: 3.8, K₂O: 2.95, P₂O₅: 3.15, B₂O₃: 1.2 (low ZnO), and (b) LZSH- Li₂O: 8.9, ZnO: 24.03, SiO₂: 53.7, Na₂O: 5.42, P₂O₅: 2.95, B₂O₃: 5 (high ZnO) were prepared by conventional melt-quench technique and converted to glass-ceramics by controlled crystallization process. The electrical properties of these samples were measured using ac impedance spectroscopy technique over a frequency range of 10 Hz-15 MHz at several temperatures in the range of 323-673 K. The ac conductivity, dc conductivity, dielectric constant and loss factor were obtained from these measurements. The dc conductivity (σ_dc) follows the Arrhenius behaviour with temperature. It is observed that σ_dc in LZSL glass is significantly higher than in the LSZH glass and the activation energies for σ_dc for LZSL and LZSH glasses are 0.59 and 1.08 eV, respectively. It further observed that the conductivity value decreases nearly one order of magnitude on conversion to glass-ceramics. The behaviour is explained on the basis of distributions and nature of alkali ions and network structures in these samples.     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

Polymer-assisted hydrothermal synthesis of Bi2S3 nanostructured flowers

Nanostructured Bi₂S₃ was hydrothermally produced from Bi₂O₃ and thiocarbohydrazide in acidic solutions containing PVA, PEG and PVP. By using XRD, SAED and Raman spectrometry, the products were orthorhombic Bi₂S₃, with four vibration modes at 139.6, 253.7, 310 and 968.9 cm⁻¹. The phase was also in accordance with the diffraction patterns obtained by simulation. SEM, TEM and HRTEM show that the products are clusters of nanorods produced in polymer-free solution, and nanostructured flowers of nanospears, nanorods and nanoplates in the respective PVA-, PEG- and PVP-added solutions, with their growths in the same direction of [0 0 1]. A formation mechanism was also proposed according to their phase and morphologies.     

Synthesis and CO2 capture property of high aspect-ratio Li2ZrO3 nanotubes arrays

High aspect-ratio Li₂ZrO₃ nanotubes were prepared by hydrothermal method using ZrO₂ nanotubes layers as templates. Characterizations of SEM, XRD, TEM and CO₂ adsorption were performed. The results showed that tetragonal Li₂ZrO₃ nanotubes arrays containing a little monoclinic ZrO₂ can be obtained using this simple method. The mean diameter of the nanotubes is approximately 150 nm and the corresponding specific surface area is 57.9 m² g⁻¹. Moreover, the obtained Li₂ZrO₃ nanotubes were thermally analyzed under a CO₂ flow to evaluate their CO₂ capture property. It was found that the as-prepared Li₂ZrO₃ nanotubes arrays would be an effective acceptor for CO₂ at high temperature.     

Infrared and visible spectroscopic studies of the ytterbium doped borate Li6Y(BO3)3

The spectroscopic study of trivalent ytterbium doped Li₆Y(BO₃)₃ is conducted in the UV-visible and infrared range. An excitation in the charge transfer band of ytterbium has been selected in order to reduce the reabsorption effect on the IR emission intensity. The maximum of the emission is located at 972 nm for an excitation at 230 nm. The energy level assignment has been successfully conducted using vibrational spectroscopy to distinguish the pure electronic transitions from the phonon-assisted ones. The splitting of the ²F_5/2 and ²F_7/2 components is equal to 523 cm⁻¹ and 676 cm⁻¹, respectively. The decay time dependence as a function of the concentration is also reported. The calculated value τ_rad is about (1.03 ± 0.01) ms for the 1% doped material. For the highest concentration, an IR excitation gives rise to the observation of a blue-green luminescence caused by two mechanisms: an erbium emission at 550 nm after upconversion and a cooperative luminescence of ytterbium ions.