Performance and stability of niobium-substituted Ba0.5Sr0.5Co0.8Fe0.2O3 − δ membranes

The phase stability, thermal expansion, electrical conductivity, and oxygen permeation of perovskite-type oxides Ba_0.5Sr_0.5(Co_0.8Fe_0.2)_1 − xNb_xO_3 − δ (x = 0 − 0.2) have been investigated. Room-temperature X-ray diffraction of as-prepared powders indicates that in the investigated compositional range solid solutions are formed. Long-term annealing experiments both in flowing air and nitrogen, at 750 °C, demonstrate that the phase instability observed in parent Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3 − δ (BSCF) is suppressed already at the minimum substitution of 5 mol% of niobium for (Co, Fe). Both electrical conductivity and thermal expansion are found to decrease with increasing niobium concentration, which behaviors can be explained by defect chemical considerations, taking into account charge compensation mechanisms by doping BSCF with Nb⁵⁺ donor cations. The oxygen permeation flux of 10 mol% Nb-substituted BSCF, in the range 800-900 °C, is reduced by 10% relative to that found for parent BSCF. Switching from helium to a CO₂-containing purge gas results in a severe reduction or cessation of the oxygen flux. Options are discussed to avoid undesired formation of surface carbonates.     

Study of La0.8Sr0.2Co0.2Cr0.8O3 − δ as a candidate coating material for the positive current collector in Na/S battery

Perovskite La_0.8Sr_0.2Co_0.2Cr_0.8O_3 − δ (LSCC) ceramic synthesized by the conventional ceramic processing technique was studied as a novel coating material for the cathode current collector in Na/S battery. Its structure, electrical conductivity, density and thermal expansion coefficient (TEC) were investigated. The corrosion performance of LSCC was in particular evaluated by electrochemical techniques in combination with long-term dip-immersion tests. The results indicated that LSCC exhibited excellent corrosion resistance in molten sodium tetrasulfide at 350 °C. The corrosion current density i_corr (0.081 mA cm^− 2) was much lower than that of 316 L stainless steel by approximately two orders of magnitude. The corrosion rate of LSCC deduced from immersion test was as low as about 12 μm year^− 1.     

Flame spray deposition of nanocrystalline dense Ce0.8Gd0.2O2 − δ thin films: Deposition mechanism and microstructural characterization

Nanocrystalline dense sub-micron thin films of Ce_0.8Gd_0.2O_2 − δ have been successfully deposited by flame spray deposition. The deposition mechanism has been identified as droplet deposition. The deposition temperature of the substrate was as low as 200 °C and the deposition rate ∼ 30 nm/min. Under these conditions the droplets have a very limited residence time in the hot zone of the flame and are deposited as liquid, forming smooth films free of particles. They exhibited a dense and crack-free microstructure. Grain growth, lattice constant, crystallographic density and surface roughness have been investigated as a function of annealing temperature. The good quality of the films, in association with the high deposition rates at low deposition temperatures shows the preeminence of the flame spray method for depositing thin films for micro-solid oxide fuel cells.     

Interaction of H2S with α-Fe2O3(0 0 0 1) surface

The atomic-scale structural changes in an α-Fe₂O₃ (hematite) (0 0 0 1) surface induced by sulfidation and subsequent oxidation processes were studied by X-ray photoemission spectroscopy, LEED, and X-ray standing wave (XSW) measurements. Annealing the α-Fe₂O₃(0 0 0 1) with a H₂S partial pressure of 1 × 10⁻⁷ Torr produced iron sulfides on the surface as the sulfur atoms reacted with the substrate Fe ions. The oxidation state of the substrate Fe changed from 3+ to 2+ as a result of the sulfidation. The XSW measured distance of the sulfur atomic-layer from the unrelaxed substrate oxygen layer was 3.16 Å. The sulfide phase consisted of three surface domains identified by LEED. Formation of the two-dimensional FeS₂ phase with structural parameters consistent with an outermost layer of (1 1 1) pyrite has been proposed. Atomic oxygen exposure oxidized the surface sulfide to a sulfate () and regenerated the α-Fe₂O₃(0 0 0 1) substrate, which was indicated by a (1 × 1) LEED pattern and the re-oxidization of Fe to 3+.     

Surface and redox chemistry of Sm0.95Ce0.05Fe1 − xNixO3 − δ perovskites

A new series of perovskite materials with formula Sm_0.95Ce_0.05Fe_1 − xNi_xO_3 − δ (0 ≤ x ≤ 0.10) has been prepared by sol-gel combustion via a citrate precursor route. X-ray diffraction data showed that materials prepared by this method had a single orthorhombic phase belonging to the Pnma (62) space group. The study of powders sintered in air and in reducing atmospheres reveals that these materials do not show phase separation in air (up to 1350 °C) nor under 5% v/v H₂/N₂ (up to 700 °C), but a phase separation of Sm₂O₃ does occur at and above 800 °C under 5% v/v H₂/N₂ without deterioration of the perovskite phase. The surfaces of all the powders (fresh, in-situ reduced and ex-situ reduced) were Sm rich, and multiple oxidation states for Fe were observed. XP analysis of in-situ reduced samples (800 °C and above) shows that metallic Fe forms in all nickel doped materials except x = 0.07. The surface oxygen vacancies and percentages of lattice and adsorbed oxygen for this series of Ni doped materials were determined and the oxygen recapturing ability is explained in terms of the multiple oxidation states of Fe.     

Crystallization and electrochemical performance of La0.6Sr0.4Co0.2Fe0.8O3 − δ-Ce0.8Gd0.2O1.9 thin film cathodes processed by single solution spray pyrolysis

La_0.6Sr_0.4Co_0.2Fe_0.8O_3 − δ-Ce_0.8Gd_0.2O_1.9 (LSCF-CGO) thin films obtained by spray pyrolysis of a single precursor solution were investigated by XRD, TEM and impedance spectroscopy at annealing temperatures ranging from 500 to 900 °C. Films annealed at 600 °C contained a mixture of amorphous regions and crystalline regions composed of fine crystallites (< 5 nm). Annealing above 600 °C increased the ratio of crystalline to amorphous material, led to the segregation of the films into distinct LSCF and CGO phases, and promoted grain growth. The electrical behavior of the films depended on annealing temperature. At testing temperatures of 400 °C and below, the polarization resistance of films with lower annealing temperatures was larger than the polarization resistance of films with higher annealing temperatures. However, at testing temperatures of 500 °C and above the polarization resistance of films with lower annealing temperatures was equal to or lower than the polarization resistance of films with higher annealing temperatures. This was reflected by the activation energy that decreased with increasing annealing temperature. The varying electrical behavior may be related to microstructural changes that caused bulk diffusion to be the rate-limiting step in films with lower annealing temperatures and oxygen dissociation to be the rate-limiting step in films with higher annealing temperatures.     

Surface studies of 2,4-pentanedione on γ-Al2O3/NiAl (1 0 0) and NiAl (1 0 0)

The chemical compound 2,4-pentanedione (Hacac) has been shown to etch the oxidized metal surfaces metals such as copper and nickel, but not their unoxidized surfaces. Here it is shown that on the γ-Al₂O₃/NiAl (1 0 0) surface (oxidized NiAl (1 0 0)) etching of aluminum occurs at 170 K and 750 K. Reflection-absorption infrared spectroscopy (RAIRS) is used to show that Hacac binds to both the clean, metallic and oxidized surfaces, but decomposition and combustion products dominate on the metallic surface and no etching occurs. The binding process that involves a deprotonation reaction of the enol species was identified by redshift in the carbonyl peaks and the appearance of an Al-H peak observed in the IR spectrum. The implication of these results is that there is both an unusual low temperature and high temperature etching of the alumina by bound acac.     

Impact of synthesis technique on the structure and electrochemical characteristics of Pr0.6Sr0.4Co0.2Fe0.8O3 − δ (PSCF) cathode material

Effect of preparation method for Pr_0.6Sr_0.4Co_0.2Fe_0.8O_3 − δ (PSCF) on its electrochemical performance was investigated. Powder samples were synthesized by hexamethylenetetramine (HMTA) and EDTA-citric acid (EC) techniques, respectively. The particles synthesized by HMTA were smaller than those prepared by EC method as proved by TEM. X-ray photoelectron spectroscopy illuminated that more oxygen sites including oxygen vacancy on the surface of HMTA-derived PSCF exist than that of EC-derived PSCF. The area specific resistance (ASR) value of HMTA-derived PSCF cathode was as low as 0.454 Ω cm² at 600 °C, whereas the ASR value of EC-derived PSCF was 0.641 Ω cm². The results in the present study demonstrated the advantages of the HMTA method in the synthesis of highly catalytic active PSCF oxide powder for SOFCs.     

Catalysis of the hydrogen oxidation reactions by Sr-doped LaMn1 − yCryO3 ± δ oxides

Sr-doped and Sr-free La_1 − xSr_xMn_1 − yCr_yO_3 ± δ (LSMC, x(Sr) = 0-0.2, y(Cr) = 0.4-0.6) perovskite-type oxides were synthesized and evaluated as single phase anodes for use in intermediate temperature solid oxide fuel cell applications. Their thermo-chemical and chemical stabilities were investigated in hydrogen at high temperatures and correlated with their oxygen non-stoichiometry (3 ± δ), determined by permanganate titration. The catalytic activity towards hydrogen oxidation was examined as a function of oxide sintering time, operating temperature, and the Sr and Cr contents, using a Pt mesh current collector. While all of the perovskite oxides studied here showed some irreversible performance degradation with time under both open circuit and anodically polarized conditions, La_0.9Sr_0.1Mn_0.6Cr_0.4O_3.03 (LSMC9164), sintered at 1200 °C for 10 h, was found to be the most catalytically active and also the most stable.     

Oxidation mechanism and ferryl domain formation on the α-Fe2O3 (0 0 0 1) surface

Recent experimental evidence calls for a reinterpretation of the oxidized structure in chemically distinct domains of the hematite (0 0 0 1) surface as the ferryl (FeO) termination rather than the bulk terminated O₃-Fe-Fe-R structure. Although this interpretation is consistent with experimental data and ab initio thermodynamics calculations, it raises serious questions about how molecular oxygen can be dissociated on a surface where reactive iron centers are slightly more than 5 Å apart. Here, we propose a novel cooperative bimolecular mechanism that provides a reasonable pathway for the formation of the unusual ferryl surface termination and should be readily reversible, which is important for understanding the function of hematite surfaces as an oxidation catalyst.     

Thermal stability of the cubic phase in Ba0.5Sr0.5Co0.8Fe0.2O3 - δ (BSCF)1

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3 - δ (BSCF) is a material with excellent oxygen ionic and electronic transport properties reported by many research groups. In its cubic phase, this mixed ionic-electronic conducting (MIEC) perovskite is a promising candidate for oxygen permeation membranes. For this application, its long-term stability under operating conditions (especially temperature and oxygen partial pressure) is of crucial importance.The present work is focused on the thermal stability of the BSCF cubic phase in the targeted temperature range for applications (700…900 °C) in light of previous studies in literature reporting a reversible transition to a hexagonal phase somewhere below 900 °C.To this end, single phase cubic BSCF powders were annealed at different temperatures over varying periods of time. Phase composition was subsequently analysed by X-ray diffractometry (XRD) in order to determine both the temperature limit and the time-scale for the formation of the hexagonal phase. Additionally, the long-term behaviour of the electrical conductivity was examined on bulk samples at 700 °C, 800 °C and 900 °C over several hundreds of hours, showing a prolonged decrease at 800 °C. The decrease in electrical conductivity at this temperature was also examined on bulk samples with different grain sizes, showing a more pronounced decrease the smaller the average grain size.Coexistence of both phases (cubic and hexagonal) could also be shown for 700 °C, however with a different phase equilibrium than at 800 °C.     

Non-universal dielectric relaxation in SrFeO3 − δ

SrFeO_3 − δ compound is prepared by the thermal decomposition method followed by ball milling. Analysis of Mössbauer spectrum and X-ray diffraction study proves the presence of multi-phase nature, i.e., Sr₈Fe₈O₂₃ and Sr₄Fe₄O₁₁ phases at room temperature. Furthermore, the Mössbauer spectrum at room temperature evidenced the presence of major Fe^3.5+ which is the resultant of equal contributions of Fe⁴⁺ and Fe³⁺. The Nyquist plot at all measured temperatures (80–230 K) suggests that the dielectric response is well associated with single relaxation time (exponential parameter, n∼1$n\sim 1$) i.e., the Debye-type. Modulus analysis exhibits the non-universal dielectric behaviour (stretched exponential parameter, β>1$\beta >1$) below 230 K and the Debye-type responds (β∼1$\beta \sim 1$) at and above 230 K. The Debye-type behaviour exhibited by SrFeO_2.81 at around room temperature in its defect state offers a new opening for this material for multifunctional applications.     

Electrical Properties of Fe-doped Perovskite-like BaNb0.75-xFexNa0.25O3-δ (0.05 < x < 0.5)

In this paper, we report the electrical properties of Fe-doped perovskite-like compounds with a nominal chemical formula of BaNb_0.75-xNa_0.25Fe_xO_3-δ (0.05 < x < 0.5) (BNF). Various solid-state structural and electrical characterization techniques, including powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), alternating current (AC) impedance spectroscopy and direct current (DC) methods were used for characterization. PXRD patterns for BNF members show the formation of perovskite-like structure. The total electrical conductivity values were determined under ambient air and wet air in the temperature up to 700 °C. The Fe concentration was strongly correlated to the conductivity response, with the x = 0.5 member exhibiting the highest conductivity in air. A relationship between the humidity content and conductivity in air was also observed in low Fe concentration BNF members (x = 0.5, 0.15), suggesting the presence of potential proton conduction; while the conductivity of high Fe content samples (x ≥ 0.3) showed little dependence on the humidity. The chemical stability of BNF samples was investigated in boiling H₂O and in flowing 100% CO₂ at elevated temperatures and the results demonstrated that all members were structurally stable under both conditions, except the x = 0.5 member which decomposed into BaCO₃ in the presence of CO₂ at 800 °C.     

Highly thermal stable transparent conducting SnO2:Sb epitaxial films prepared on α-Al2O3 (0 0 0 1) by MOCVD

Antimony-doped tin oxide (SnO₂:Sb) single crystalline films have been prepared on α-Al₂O₃ (0 0 0 1) substrates by metal organic chemical vapor deposition (MOCVD). The antimony doping was varied from 2% to 7% (atomic ratio). Post-deposition annealing of the SnO₂:Sb films was carried out at 700-1100 °C for 30 min in atmosphere ambient. The effect of annealing on the structural, electrical and optical properties of the films was investigated in detail. All the SnO₂:Sb films had good thermal stability under 900 °C, and the 5% Sb-doped SnO₂ film exhibited the best opto-electrical properties. Annealed above 900 °C, the 7% Sb-doped SnO₂ film still kept high thermal stability and showed good electrical and optical properties even at 1100 °C.     

Structural and photoluminescence properties of SnO2:Ga films deposited on α-Al2O3 (0 0 0 1) by MOCVD

Gallium-doped tin oxide (SnO₂:Ga) films have been prepared on α-Al₂O₃ (0 0 0 1) substrates at 500 °C by the pulse mode metalorganic chemical vapor deposition (MOCVD) method. The relative amount of Ga (Ga/(Ga+Sn) atomic ratio) varied from 3% to 15%. Post-deposition annealing of the films was carried out at different temperatures for 1.5 h in ambient atmosphere . The structural, electrical, optical and photoluminescence (PL) properties of the films have been investigated as a function of annealing temperature. All the films have the rutile structure of pure SnO₂ with a strong (2 0 0) preferred orientation. A single ultraviolet (UV) PL peak near 337.83 nm was observed at room temperature for the 3% Ga-doped as-grown film and near 336 nm for the 15%-doped film, which can be ascribed to electron transition from the oxygen vacancy and interstitial Ga³⁺ donor levels to the acceptor level formed by the substitution of Ga³⁺ for the Sn site. After annealing, the luminescence spectra have changed a little bit, which is being discussed in detail.     

Rovibrational spectroscopy of the Fermi-interacting ν4 = 1 and ν3 = ν6 = 1 levels of DCF3

The high-resolution infrared spectrum of deuterated fluoroform (DCF₃) was studied in the 700 and 1200 cm⁻¹ regions, with the aim of assigning and analyzing the ν₄ CF₃ asymmetric stretching vibration. The Fermi-type anharmonic coupling between the ν₄ = 1 and ν₃ = ν₆ = 1 rovibrational levels, already mentioned in an early work of Ruoff et al. [Spectrochimica Acta Part A 31A (1975) 1099-1100], was studied here for the first time under high resolution. Assignments in the ν₃ + ν₆/ν₄ band system were confirmed and extended by the identification of the ν₃ + ν₆ − ν₆ and ν₄-ν₆ bands in the 700 cm⁻¹ region, the latter being enhanced near the Fermi crossings of the studied levels. Data from both the hot and difference bands were included in the analysis. The close separation of the studied vibrational levels of about 14.8 cm⁻¹ produces a large variety of resonance crossings which involve levels with . Besides the Fermi () and Coriolis () resonances, they were accounted for by inclusion of additional higher-order ( and ) interaction terms between the vibrational states. The least-squares fit of more that 16,000 vibration-rotation transitions provides a quantitative reproduction of data in all bands.     

Characterization of YSr2Fe3O8 − δ as electrode materials for SOFC

YSr₂Fe₃O_8 − δ was prepared by traditional solid state reaction method and characterized by X-ray diffraction, ac impedance, dc conductivity, dilatometry and thermogravimetric analysis for possible use in solid oxide fuel cells (SOFCs). YSr₂Fe₃O_8 − δ crystallizes with tetragonal symmetry in the space group P4/mmm and found to be stable at high temperatures under H₂ and air. Four probe dc electrical conductivity measurements show that the conductivity increases up to 745 K and then decreases with temperature; the highest conductivity σ_745K = 43.5 S cm^− 1. The n-type conductivity at low oxygen partial pressure (pO₂) changes to p-type at high pO₂. Polarization behavior was investigated measuring the ac impedance response in symmetrical cell arrangements in air with YSZ and GDC electrolytes. Cathodic area specific resistance (ASR) varies with firing temperature. The lowest area specific resistance was observed with a GDC electrolyte fired at 1000 °C. In case of YSZ, ASR increases and in case of GDC, ASR decreases in air when electrode firing temperature decreases. At 800 °C ASRs are 0.20 Ω cm² and 0.65 Ω cm² with GDC and YSZ electrolytes, respectively, in air. Fuel cell measurements with symmetrical electrodes were performed using a thin YSZ electrolyte under H₂ at anode and air at cathode, show that the power density is about 0.035 W/cm² at 900 °C.     

The rotational spectra of the υ8 = υ9 = 1 and υ6 = υ7 = 1 interacting vibrational states of nitric acid (HNO3)

The analysis of the rotational spectrum of HNO₃ has been extended to include the υ₈ = υ₉ = 1 state at 1205.7 cm⁻¹ and the υ₆ = υ₇ = 1 state at 1223.4 cm⁻¹. Based on 78-519 GHz data, the assignments in the 8¹9¹ vibrational state have been significantly expanded from the previously reported microwave measurements [T.M. Goyette, F.C. De Lucia, J. Mol. Spectrosc. 139 (1990) 241-243]. A new microwave analysis is also reported for the 6¹7¹ vibrational state. A simultaneous analysis takes into account the localized ΔK_a = ±2 Fermi resonances between the vibrational states, describes the torsional splitting of 3.3 and 1.4 MHz for the 8¹9¹ and 6¹7¹ states respectively, and fits to experimental accuracy over 1500 rotational transition frequencies that extend up to J = 59. Infrared energy levels [A. Perrin, J.-M. Flaud, F. Keller, A. Goldman, R. D. Blatherwick, F. J. Murcray, C. P. Rinsland, J. Mol. Spectrosc. 194 (1999) 113-123] were also included in the analysis and fit to experimental accuracy. Measurement of strongly perturbed transitions in each vibrational state provide a determination of the band origin difference of 17.733184(17) cm⁻¹. The rotational constants agree well with those predicted by vibrational-rotational constants of the fundamental modes. Furthermore, the analysis will provide a very accurate simulation of the infrared spectrum of HNO₃ in the 8.3 μm region.     

Transparent conducting Sn-doped Ga1.4In0.6O3 films prepared on α-Al2O3 (0 0 0 1) by MOCVD

Sn-doped Ga_1.4In_0.6O₃ films have been prepared on α-Al₂O₃ (0 0 0 1) substrates by the metalorganic chemical vapor deposition (MOCVD) method. The Sn-doping was varied from 0% to 7% (atomic ratio). Polycrystalline films with resistivity of 4.9 × 10⁻³Ω cm, carrier concentration of 5.9 × 10¹⁹ cm⁻³ and Hall mobility of 21.4 cm² v⁻¹ s⁻¹ was obtained at 5 at.% of Sn concentration. The average transmittance for the Sn-doped Ga_1.4In_0.6O₃ films in the visible range was over 90%. The bandgap of the films varies from 3.85 to 4.21 eV.