Electrochemical properties of α-Fe2O3 /MWCNTs as anode materials for lithium-ion batteries

α-Fe₂O₃/MWCNTs composites were prepared by a simple hydrothermal process. The crystalline structure and the electrochemical performance of the as-synthesized samples were investigated. Results show that as anode materials for lithium-ion batteries, the α-Fe₂O₃/MWCNTs exhibit an initial discharge capacity of 1256 ± 5 mAh g⁻¹ and a stable specific discharge capacity of 430 ± 5 mAh g⁻¹ at ambient temperature, for up to 100 cycles with no noticeable capacity fading, while the initial discharge capacity of the bare Fe₂O₃ is 992.3 mAh g⁻¹, and the discharge capacity is 146.6 mAh g⁻¹ after 100 cycles. Moreover, the α-Fe₂O₃/MWCNTs composites also exhibit excellent rate performance.     

Porous LiNi0.75Co0.25O2 microspheres prepared via a hydrothermal process as cathode material for lithium ion batteries

Porous LiNi_0.75Co_0.25O₂ microspheres are successfully prepared by a simple hydrothermal process by using H[Ni_0.75Co_0.25OOH]₃ and LiOH as starting materials in the presence of urea for the first time. The synthesized samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), specific surface area (S_BET), and electrochemical performance. The synthesized LiNi_0.75Co_0.25O₂ has a good electrochemical performance with an initial discharge capacity of 169.3 mA g⁻¹ and good capacity retention of 96.7% after 50 cycles at 0.2 C (25 mA g⁻¹). The electrochemical lithium ion insertion/extraction process is quite reversible even at 5 C. Furthermore, the structure in the charge-discharge process is stable and the impedance increased slowly during cycling.     

Promising anode material for lithium-ion cells based on cobalt oxide synthesized by microwave heating

High-performance anode material for lithium-ion cell based on cobalt oxide was synthesized through a combination of sol-gel route and subsequent microwave heating. The influence of microwave irradiation temperature of the precursor on the characteristics of the active materials formed was studied. The physicochemical, structural, and morphological properties of the materials were studied in addition to the electrochemical performance by cyclic voltammetry and charge-discharge cycling vs. Li⁺/Li. Microwave heating at 350 °C resulted in the formation of Co₃O₄, whereas at 450 and 550 °C, a mixture of Co₃O₄, CoO, and Co was formed. Co₃O₄ synthesized at 350 °C possessed porous morphology with high specific surface area and exhibited superior electrochemical performance with initial specific capacity of 982 mAh g^?1 and coulombic efficiency of ~75% along with good cycle performance retaining ~87% of initial capacity after 60 cycles.     

Hydrogen peroxide biosensor based on gold nanoparticles/thionine/gold nanoparticles/multi-walled carbon nanotubes-chitosans composite film-modified electrode

In this paper, an amperometric electrochemical biosensor for the detection of hydrogen peroxide (H₂O₂), based on gold nanoparticles (GNPs)/thionine (Thi)/GNPs/multi-walled carbon nanotubes (MWCNTs)-chitosans (Chits) composite film was developed. MWCNTs-Chits homogeneous composite was first dispersed in acetic acid solution and then the GNPs were in situ synthesized at the composite. The mixture was dripped on the glassy carbon electrode (GCE) and then the Thi was deposited by electropolymerization by Au-S or Au-N covalent bond effect and electrostatic adsorption effect as an electron transfer mediator. Finally, the mixture of GNPs and horseradish peroxidase (HRP) was assembled onto the modified electrode by covalent bond. The electrochemical behavior of the modified electrode was investigated by scanning electron microscope, cyclic voltammetry and chronoamperometry. This study introduces the in situ-synthesized GNPs on the other surface of the modified materials in H₂O₂ detection. The linear response range of the biosensor to H₂O₂ concentration was from 5 × 10⁻⁷ mol L⁻¹ to 1.5 × 10⁻³ mol L⁻¹ with a detection limit of 3.75 × 10⁻⁸ mol L⁻¹ (based on S/N = 3).     

Hard carbon/Li2.6Co0.4N composite anode materials for Li-ion batteries

Hard carbon/Li_2.6Co_0.4N composite anode electrode is prepared to reduce the initial high irreversible capacity of hard carbon, which hinders potential application of hard carbon in lithium ion batteries, by introducing Li_2.6Co_0.4N into hard carbon. Lithiated Li_2.6Co_0.4N provides the compensation of lithium in the first cycle, leading to a high initial coulombic efficiency of ca. 100% versus lithium. As-prepared hard carbon/Li_2.6Co_0.4N composite electrode presents initial capacity of 438 mA h g^− 1. A full cell using LiCoO₂ cathode and the composite anode shows much higher initial coulombic efficiency and capacity than those of a cell using LiCoO₂ and hard carbon anode. This paves the way to reduce the large initial irreversible capacity of hard carbon.     

Synthesis of spherical LiFePO4/C via Ni doping

Spherical LiFePO₄/C powders were synthesized by the conventional solid-state reaction method via Ni doping. Low-cost asphalt was used as both the reduction agent and the carbon source. An Ni-doped spherical LiFePO₄/C composite exhibited better electrochemical performances compared to an un-doped one. It presented an initial discharge capacity of 161 mAhg⁻¹ at 0.1 C rate (the theoretical capacity of LiFePO₄ with 5 wt% carbon is about 161 mAhg⁻¹). After 50 cycles at 0.5 C rate, its capacity remained 137 mAhg⁻¹ (100% of the initial capacity) compared to 115 mAhg⁻¹ (92% of the initial capacity) for an un-doped one. The electrochemical impedance spectroscopy analysis and cyclic voltammograms results revealed that Ni doping could decrease the resistance of LiFePO₄/C composite electrode drastically and improve its reversibility.     

One-step synthesis and electrochemical behavior of LiMnO2 and its composite from MnO2 in the presence of glucose

LiMnO₂ and 0.23Li₂MnO₃·0.77LiMnO₂ were prepared by a convenient one-step solid-state reaction from MnO₂ using glucose as organic carbon resource. The crystal structure and morphology of the as-prepared materials was examined by X-ray powder diffraction and field emission scanning electron microscopy, respectively. The ration of Li to Mn was determined by means of atomic absorption spectrometry and the Li/Mn molar ratio in the products was 1.23. The electrochemical properties were investigated by charge-discharge test and electrochemical impedance measurements. The prepared composite material presented an initial discharge capacity of 45 mAh g^-1 and a good cycling performance with reversible capacity of 218 mAh g^-1 after 30 cycles. On the basis of the experimental results, the discharge efficiency of this composite material more than 100% was also discussed.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Improvement of electrochemical performance of all-solid-state lithium secondary batteries by surface modification of LiMn2O4 positive electrode

To improve the electrochemical performance of an all-solid-state In/80Li₂S⋅20P₂S₅ (electrolyte)/LiMn₂O₄ cell, a lithium-titanate thin film was used to coat LiMn₂O₄. The interfacial resistance between LiMn₂O₄ and the electrolyte (measured after initial charging) decreased when the LiMn₂O₄ particles were coated with lithium-titanate. A cell with lithium-titanate-coated LiMn₂O₄ had a higher capacity than a cell with noncoated LiMn₂O₄ for current densities in the range 0.064 to 2.6 mA cm^− 2. Additionally, a cell with coated LiMn₂O₄ retained 96% of the 10th-cycle reversible capacity at a current density of 0.064 mA cm^− 2 after 50 cycles.     

Electrochemical behaviour of sputtered c-V2O5 and LiCoO2 thin films for solid state lithium microbatteries

Here are reported for the first time electrochemical data on all-solid-state lithium microbatteries using crystalline sputtered V₂O₅ thin films as cathode materials and LiPON as solid electrolyte. The stable specific capacity of 30 µAh/cm² found with a 2.4 µm thick film competes very well with the best values obtained for solid state microbatteries using amorphous films. With the challenge of decreasing the temperature of heat treatment for sputtered LiCoO₂ thin films, we show that a temperature of 500 °C combined with an optimized bias sputtering (-50 V) allows to get highly crystalline deposits, to minimize the presence of Co₃O₄ and to suppress any trace of the cubic phase. At the same time the theoretical specific capacity is reached in the 4.2 V-3 V range and a good cycling behaviour is achieved with a high capacity of 50 µAh/cm²/µm after 140 cycles at 10 µA.cm².