Mn4+掺杂对BiFeO3陶瓷微观结构和电学性能的影响研究

利用传统的固相反应法制备了BiFe_1-xMn_xO₃ (x= 0-0.20)陶瓷样品, 研究了不同Mn⁴⁺掺杂量对BiFeO₃陶瓷密度、物相结构、显微形貌、 介电性能和铁电性能的影响.实验结果表明:所制备的BiFe_1-xMn_xO₃ 陶瓷样品的钙钛矿主相均已形成,具有良好的晶体结构, 且在掺杂量x=0.05附近开始出现结构相变.随着Mn⁴⁺添加量的增加, 体系的相结构有从菱方钙钛矿向斜方转变的趋势,且样品电容率大幅度增大, 而介电损耗也略有增加;在测试频率为10⁴ Hz条件下, BiFe_0.85Mn_0.15O₃ (ε_r=1065)的 ε_r是纯BiFeO₃ (ε_r=50.6)的22倍; 掺杂后样品的铁电极化性能均有不同程度的提高,可能是由于Mn⁴⁺稳定性优于 Fe³⁺,高价位Mn⁴⁺进行B位替代改性BiFeO₃陶瓷, 能减少Bi³⁺挥发,抑制Fe³⁺价态波动,从而降低氧空位浓度,减小样品的电导和漏电流.     

焙烧温度对SiO2负载的Co3O4纳米粒子表面氧缺陷浓度和CO氧化催化性能的影响

以传统的浸渍法,在不同焙烧温度下制备了用于CO氧化反应的Co₃O₄/SiO₂催化剂．通过激光拉曼光谱(Raman)、X射线光电子能谱(XPS)、X射线衍射(XRD)、程序升温还原(TPR)和X射线吸收精细结构谱(XAFS)表征了该系列催化剂的结构．在所有的催化剂中,XRD和Raman光谱都只检测到了Co₃O₄晶相的存在．与Co₃O₄体相相比,XPS结果表明在200 oC焙烧的(Co₃O₄(200)/SiO₂)催化剂中Co₃O₄表面上存在着过量的Co²⁺．与XPS的结果一致,TPR结果表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄表面上存在氧缺陷, 并且XAFS结果也表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄具有更多的Co²⁺．提高焙烧温度使得过量的Co²⁺进一步氧化为Co³⁺,同时降低了表面氧缺陷浓度,从而得到计量比的Co₃O₄4/SiO₂催化剂．在所有的负载催化剂中Co₃O₄(200)/SiO₂催化剂表现出了最好的CO氧化催化性能,表明过量Co²⁺和表面氧缺陷的存在能够促进Co₃O₄催化CO氧化反应的活性.     

针状纳米MnxNi0.5-xZn0.5Fe2O4的共沉淀法制备及表征

通过在碱液中共沉淀Mn²⁺、Ni²⁺和Fe²⁺后制备了棒状的前躯体,前躯体于不同温度煅烧后制得了Mn_xNi_0:5-xZn_0:5Fe₂O₄棒状体. 利用X射线衍射仪和透射电镜对棒状体的物相、形貌及粒径进行了表征,并利用振动样品磁强计对磁性能进行研究. 结果表明长径比大于15的棒状,随着x值的增加,Mn_xNi_0:5-xZn_0:5Fe₂O₄样品的直径增加,长度下降,长径比变小,当x=0.5时其直径在50 nm左右而长径比减小到7～8. 随着x值的增加,样品的矫顽力先增加后减少,x值达到0.4时样品的矫顽力再次增加,当煅烧温度为600 oC,x=0.5时样品的矫顽力最大为134.3 Oe. 饱和磁化强度随着x值的增加先增加后减少,当煅烧温度为800 oC和x=0.2时达到最大为68.5 Oe.     

具有介孔结构的MnSiO3@Fe3O4@C纳米粒子的制备以及作为pH响应的T1-T2*双模MRI造影剂的研究应用

本文通过一个简单的、温和的方案制备了平均尺寸为120 nm，介孔结构的纳米粒子MnSiO₃@Fe₃O₄@C. 粒子的细胞毒性微小，可以用作T₁-T₂^*双模MRI造影剂. 酸性条件下MnSiO₃@Fe₃O₄@C释放出大量的Mn²⁺缩短T₁弛豫时间，提高成像分辨率. 超顺磁性的Fe₃O₄可以增强T₂对比成像，检测病变组织. 类似于肿瘤微环境/细胞器的酸性PBS(pH=5.0)中Mn²⁺的释放率达到31.66%，约为中性条件(pH=7.4)下的7倍. 释放的Mn²⁺通过内吞作用被细胞摄取，经肾脏排出，细胞毒性实验表明，MnSiO₃@Fe₃O₄@C具有低的细胞毒性，即使高浓度的200 ppm MnSiO₃@Fe₃O₄@C对HeLa细胞的毒性也相对较小. 对荷瘤小鼠静脉注射定量MnSiO₃@Fe₃O₄@C后，可以观察到一个快速增强的对比成像，给药24 h后，T₁MRI信号显著增强，达到132%，而T₂信号则明显降低至53.8%，活体MR成像证明了MnSiO₃@Fe₃O₄@C可以同时作为阳性和阴性造影剂. 此外，得益于介孔MnSiO₃优秀的酸敏感性，MnSiO₃@Fe₃O₄@C可以作为一种潜在的药物载体，实现肿瘤的诊疗一体化.     

LiFexMn1-xPO4固溶体的密度泛函理论与电化学研究

本文用DFT计算方法研究了LiFe_xMn_1-xPO₄的热力学稳定性和嵌/脱锂电位. 结果表明，LiFe_xMn_1-xPO₄固溶体的自由能比相分离的LiFePO₄/LiMnPO₄混合物略高，这两种形式可能在实际LiFe_xMn_1-xPO₄材料中共存. 计算表明，LiFe_xMn_1-xPO₄固溶体的嵌/脱锂电位随锰/铁比以及过渡金属离子的空间排列而变化，并用计算结果解释了放电曲线的形状. 采用固相反应法合成了LiFe_xMn_1-xPO₄材料并研究了其电化学性质，实验中观察到附加的放电平台，其出现可能与LiFe_xMn_1-xPO₄固溶体的存在有关.     

Eu2+,Mn2+在BaZnP2O7中的发光及Eu2+→Mn2+能量传递

采用高温固相法合成了BaZnP₂O₇:Eu²⁺,Mn²⁺荧光粉，并对其发光性质及Eu²⁺对Mn²⁺的能量传递机理进行了研究.Eu²⁺和Mn²⁺在380 nm和670nm的发射峰分别由Eu²⁺的5d—4f跃迁和Mn²⁺的⁴T₁(^{4相似文献}   

聚对苯撑/LiNi0.5Fe2O4纳米复合热电材料的制备及其性能研究

本文以流变相反应法原位合成了聚对苯撑/LiNi_0.5Fe₂O₄纳米复合热电材料,并对其热电性能进行表征,研究了放电等离子烧结时保温时间对其热电性能的影响.结果发现,复合材料铁氧体颗粒粒径为100---300nm,其外部被一层聚对苯撑膜包覆.电子在Fe²⁺和Fe³⁺之间的跳跃机理在铁氧体电导中占主导作用,因此聚对苯撑/LiNi_0.5Fe₂O₄复合材料具有n型导电特性.随着保温时间增加,复合材料电导率基本不变,但热导率逐渐增大且Seebeck系数逐渐减小,导致热电优值系数降低.由于结合了有机物高电导率和低热导率以及无机材料高赛贝克系数的优点,所制备的复合材料热电性能较单一材料有较大提高.     

Al掺杂的尖晶石型LiMn2O4的结构和电子性质

采用基于密度泛函理论的第一性原理方法, 在广义梯度近似(GGA)和GGA+U方法下对尖晶石型LiMn₂O₄及其Al掺杂 的尖晶石型LiAl_0.125Mn_1.875O₄晶体的结构和电子性质进行了计算. 结果表明: 采用GGA方法得到尖晶石型LiMn₂O₄是立方晶系结构, 其中的Mn离子为+3.5价, 无法解释它的Jahn-Teller 畸变. 给出的LiMn₂O₄能带结构特征也与实验结果不符. 而采用GGA+U方法得到在低温下的LiMn₂O₄和其掺杂 体系LiAl_0.125Mn_1.875O₄的晶体都是正交结构, 与实验一致. 也能明确地确定Mn的两种价态Mn³⁺/Mn⁴⁺的分布并且能够说明Mn³⁺O₆的z方向有明显的Jahn-Teller 畸变, 而Mn⁴⁺O₆则没有畸变. LiMn₂O₄的能带结构与实验比较也能够符合. 采用GGA+U方法对Al掺杂体系的LiAl_0.125Mn_1.875O₄的研究表明, 用Al替换一个Mn不会明显地改变晶体的电子性质, 但可以有效地消除Al³⁺O₆ 八面体的Jahn-Teller畸变, 从而改善正极材料LiMn₂O₄的性能, 这与电化学实验的观察结果相一致.     

Superacid Catalyst SO42-/ZrO2-La2O3 Prepared by Ultrasonic Co-precipitation and Low Temperature Aging

低温陈化超声波共沉淀法制得SO₄^2-/ZrO^2-La₂O₃前驱体， 经H₂SO₄处理， 在不同温度下焙烧得到纳米晶催化剂SO₄^2-/ZrO^2-La₂O₃；用Hammett指示剂法测定其酸性. 用XRD、BET、TEM、IR和XPS对样品进行表征，其催化活性用醋酸和甘油的酯化反应进行了评价. 结果表明经超声波搅拌和低温(-15 ºC)陈化，650 ºC焙烧4 h得到的固体超强酸表现出较高催化活性.     

压力对纳米CoFe2O4/SiO2复合材料结构的影响

 采用溶胶-凝胶工艺和高温高压实验技术,制备了纳米CoFe₂O₄/SiO₂复合材料。利用X射线衍射仪、扫描电子显微镜和振动样品磁强计,对样品的结构、微观形貌和磁性进行了研究,并对CoFe₂O₄中阳离子的占位情况进行了讨论。结果表明,随着处理压力的升高,样品的晶粒尺寸增大,晶格常数减小,比饱和磁化强度增大。通过计算结果可以推断,压力的升高导致CoFe₂O₄中的部分Fe³⁺从A位移向了B位,而部分Co²⁺则从B位移向了A位。     

Preparation and magnetic properties of the conductive Co(1−x)NixFe2O4/polyaniline microsphere composites

Core-shell Co_(1−x)Ni_xFe₂O₄/polyaniline nanoparticles, where the core was Co_(1−x)Ni_xFe₂O₄ and the shell was polyaniline, were prepared by the combination of sol-gel process and in-situ polymerization methods. Nanoparticles were investigated by Fourier transform spectrometer, X-ray diffraction diffractometer, Scanning electron microscope, Differential thermal analysis and Superconductor quantum interference device. The results showed that the saturation magnetization of pure Co_(1−x)Ni_xFe₂O₄ nanoparticles were 57.57 emu/g, but Co_(1−x)Ni_xFe₂O₄/polyaniline composites were 37.36 emu/g. It was attributed to the lower content (15 wt%), smaller size and their uneven distribution of Co_(1−x)Ni_xFe₂O₄ nanoparticles in the final microsphere composites. Both Co_(1−x)Ni_xFe₂O₄ and PANI/Co_(1−x)Ni_xFe₂O₄ showed superparamagnetism.     

Y2(Fe1-x-y,Coy,Crx)17化合 物的结构及居里温度

通过x射线衍射及磁测量手段研究了Y₂(Fe_1-y-x,Co_y,C r_x)₁₇化合物的结 构及居里温度.研究结果表明Y₂(Fe_1-y-x,Co_y,Crx)₁₇化合物具有六 角相的Th₂Ni₁₇型结构.随着x的增加，Y₂(Fe 关键词： 2(Fe_1-y-x')" href="#">Y₂(Fe_1-y-x y')" href="#">Co_y x)_{1 7}化合物')" href="#">Cr_x)_{1 7}化合物 x射线衍射 居里温度     

Organic acid assisted solid-state synthesis of Li1.2Ni0.16Co0.08Mn0.56O2 nanoparticles as lithium ion battery cathodes

Lithium-rich layered oxide Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ can be referred as a crystalline mixture of Li₂MnO₃ and LiNi_0.4Co_0.2Mn_0.4O₂ at equal molar ratio. In the paper, the solid state reaction of M(AC)₂·4H₂O (M = Mn, Co and Ni) and LiOH·H₂O has been performed to obtain nanocrystalline Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ using a small molecular organic acid (i.e., oxalic acid (OA), citric acid (CA) or tartaric acid (TA)) as additive. The introduction of organic acids can help to improve the layered structure and inhibit the particle growth of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂, and the different organic acids exert distinct influences on the structural and electrochemical properties of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂. In detail, the nanoparticles obtained in the presence of OA have the smallest average size of 50–150 nm, which correspondingly exhibit the highest initial discharge capacity of 267.52 mAh g⁻¹ at 0.1C and the best high-rate capability (e.g., 152.22 mAh g⁻¹, 5C) when applied as a lithium ion battery cathode. Furthermore, the active substance obtained from TA shows the best cycling stability and a discharge capacity of 202.42 mAh g⁻¹ can be retained after 50 cycles at 0.5C.     

Complex permittivity, complex permeability and microwave absorption properties of ferrite-paraffin polymer composites

We have investigated the electromagnetic (EM) characteristics of Co_xMn_1−xFe₂O₄ spinel ferrite (where x=0.0, 0.5 and 1.0) nanoparticles (NPs)/paraffin nanocomposite material at 8-20 GHz. Co_xMn_1−xFe₂O₄ NPs have been synthesized by cetyltrimethylammonium assisted hydrothermal route using NaOH. A variation in complex dielectric permittivity and magnetic permeability at room temperature with frequency in the range 8-20 GHz has been studied. Particles showed phase purity and crystallinity in powder X-ray diffraction (XRD) analysis. At the same time, Co_xMn_1−xFe₂O₄ NPs demonstrated a spinel cubic structure from XRD results. A reflection loss of −46.60 dB was found at 10.5 GHz for an absorber thickness of 2 mm. Co_xMn_1−xFe₂O₄ may be attractive candidates for EM wave absorption materials.     

The magnetic properties of diluted CoFe2O4 nanomaterials

The magnetic properties of （Cox Fe1-x）A （Zn1-x Fe1＋x）B O4 are studied using mean-field theory and the probability distribution law to obtain the saturation magnetization, the coercive field, the critical temperature, and the exchange interactions with different values of D （nm） and x. High-temperature series expansions （HTSEs） combined with the Pade approximant are used to calculate the critical temperature of （CoxFe1-x）A（Znl-xFe1＋x）BO4, and the critical exponent associated with magnetic susceptibility is obtained.     

Structural, transport and electrochemical properties of LiNi1 − yCoyMn0.1O2 and Al, Mg and Cu-substituted LiNi0.65Co0.25Mn0.1O2 oxides

LiNi_{1 - y − z}Co_yMn_zO₂ (y = 0.25, 0.35, 0.5, 0.6; z = 0.1, 0.2), LiNi_0.63Cu_0.02Co_0.25Mn_0.1O₂, LiNi_0.65Co_0.25Mn_0.08Al_0.02O₂, LiNi_0.65Co_0.25Mn_0.08Mg_0.02O₂ and LiNi_0.65Co_0.25Mn_0.08Al_0.01Mg_0.01O₂ cathode materials were synthesized by a soft chemistry EDTA-based method. Structural and transport properties of pristine and delithiated materials (Li_xNi_0.65Co_0.25Mn_0.1O₂, Li_xNi_0.55Co_0.35Mn_0.1O₂ and LiNi_0.63Cu_0.02Co_0.25Mn_0.1O₂ oxides) are presented. In the considered group of oxides there is no correlation between electrical conductivity and the a parameter (M-M distance in the octahedra layers). The results of electrochemical performance of cathode materials are presented. The best stability during first 10 cycles was obtained for Li/Li_xNi_0.63Cu_0.02Co_0.25Mn_0.1O₂ cell due to enhanced kinetics of intercalation process.     

Synthesis and characterizations of water-based ferrofluids of substituted ferrites [Fe1−xBxFe2O4, B=Mn,Co (x=0–1)] for biomedical applications

Nanomagnetic particles have great potential in the biomedical applications like MRI contrast enhancement, magnetic separation, targeting delivery and hyperthermia. In this paper, we have explored the possibility of biomedical applications of [Fe_1−xB_xFe₂O₄, B=Mn, Co] ferrite. Superparamagnetic particles of substituted ferrites [Fe_1−xB_xFe₂O₄, B=Mn, Co (x=0–1)] and their fatty acid coated water base ferrofluids have been successfully prepared by co-precipitation technique using NH4OH/TMAH (Tetramethylammonium hydroxide) as base. In vitro cytocompatibility study of different magnetic fluids was done using HeLa (human cervical carcinoma) cell lines. Co²⁺-substituted ferrite systems (e.g. CoFe₂O₄) is more toxic than Mn²⁺-substituted ferrite systems (e.g. MnFe₂O₄, Fe_0.6Mn_0.4Fe₂O₄). The later is as cytocompatible as Fe₃O₄. Thus, Fe_1−xMn_xFe₂O₄ could be useful in biomedical applications like MRI contrast agent and hyperthermia treatment of cancer.     

Electronic structure studies of the spinel CoFe2O4 by X-ray photoelectron spectroscopy

The spinel CoFe₂O₄ has been synthesized by combustion reaction technique. X-ray photoelectron spectroscopy shows that samples are near-stoichiometric, and that the specimen surface both in the powder and bulk sample is most typically represented by the formula (Co_0.4Fe_0.6)[Co_0.6Fe_1.4]O₄, where cations in parentheses occupy tetrahedral sites and those within square brackets in octahedral sites. The results demonstrate that most of the iron ions are trivalent, but some Fe²⁺ may be present in the powder sample. The Co 2p_3/2 peak in powder sample composed three peaks with relative intensity of 45%, 40% and 15%, attributes to Co²⁺ in octahedral sites, tetrahedral sites and Co³⁺ in octahedral sites. The O 1s spectrum of the bulk sample is composed of two peaks: the main lattice peak at 529.90 eV, and a component at 531.53 eV, which is believed to be intrinsic to the sample surface. However, the vanishing of the O 1s shoulder peak of the powder specimen shows significant signs of decomposition.     

R3(Fe1-xCox)29-yCry(R=Gd,Sm)化合物相稳定性研究

在制备出Gd₃(Fe_1-xCo_x)_29-yCr_{y化合物基础上，成功制备出Sm3(Fe1-xCox)29 -yCry化合物，通过x射线衍射和热磁分析对R3(Fe1-x< /sub>Co x)29-yCry 关键词： 3(Fe1-xCox)29-yCry化合物')" href="#">R3(Fe1-xCox)29-yCry化合物 相结构 单轴磁晶各向异性}     

Effects of Mn substitution of Co and Fe in spinel CoFe2O4 thin films

Effects of Mn substitution for Co and Fe on the structural and magnetic properties of inverse-spinel CoFe₂O₄ have been investigated. Mn_xCo_1−xFe₂O₄ and Mn_yCoFe_2−yO₄ thin films were prepared by a sol–gel method. The observed increase of the lattice constant of Mn_xCo_1−xFe₂O₄ indicates that Mn²⁺ ions substitute the octahedral Co²⁺ sites. Conversion electron Mössbauer spectroscopy data indicate that a fraction of octahedral Co²⁺ ions exchange sites with tetrahedral Fe³⁺ ions through Mn doping. Vibrating-sample magnetometry data exhibit a large increase of saturation magnetization for both Mn_xCo_1−xFe₂O₄ and Mn_yCoFe_2−yO₄ films compared to that of the CoFe₂O₄ film. Such enhancement of magnetization can be explained in terms of a breaking of ferrimagnetic order induced by the Co²⁺ migration.