硅铝催化剂催化有机溶剂木质素的解聚

E cient conversion of lignin to fine chemicals and biofuel become more and more attractive in biorefinery. In this work, we used a series of silica-alumina catalysts (i.e., SiO₂-Al₂O₃, HY, Hβ, and HZSM-5) to degrade lignin into arenes and phenols. The relationship between the catalyst structure and lignin depolymerization performance was investigated. The results showed that both acidity and pore size of the catalyst could in uence the conversion of lignin. In the volatilizable product, phenols were identified as the main phenolic monomers via gas chromatography-mass spectrometer. SiO₂-Al₂O₃ was the most effcient catalyst, giving 90.96% degree of conversion, 12.91% yield of phenols, and 2.41% yield of arenes in ethanol at 280℃ for 4 h. The Fourier transform infrared spectroscopy and ¹H nuclear magnetic resonance spectroscopy analysis demonstrated that deoxygenation and alkylation occurred in this process. The effect of solvents was also investigated and the results showed that ethanol was the most effcient solvent.     

HIGH-YIELD PRODUCTION OF MULTI-WALLED CARBON NANOTUBES BY CATALYTIC DECOMPOSITION OF BENZENE VAPOR

Multi-walled carbon nanotubes (CNTs) have been synthesized on γ-Al₂O₃ supported unitary, binary or trinity metal (Fe, Co, Ni) catalysts with benzene as carbon source in the range of 600 to 810 ℃. The growth of CNTs was carried out in a fixed bed flow reactor and the quality of carbon deposits was characterized by transmission electron microscopy. The preparation was optimized and the high-yield production of CNTs has been achieved for three mixture catalysts with the yield of high-quality CNTs higher than 200% within 60 min, reaching a maximum of 278% for 1.51 mmol/g Fe-1.51 mmol/g Co/γ-Al₂O₃ catalyst. This provides a good alternative for future large scale and low cost production of CNTs for applications.     

Ni/α-Al2O3催化剂作用下苯甲醚的加氢脱氧

Ni-based catalysts supported on di erent supports (α-Al₂O₃,γ-Al₂O₃, SiO2, TiO₂, and ZrO₂) were prepared by impregnation. Effects of supports on catalytic performance were tested using hydrodeoxygenation reaction (HDO) of anisole as model reaction. Ni/α-Al₂O₃ was found to be the highest active catalyst for HDO of anisole. Under the optimal conditions, the anisole conversion is 93.25% and the hydrocarbon yield is 90.47%. Catalyst characteriza-tion using H₂-TPD method demonstrates that Ni/α-Al₂O₃ catalyst possesses more amount of active metal Ni than those of other investigated catalysts, which can enhance the cat-alytic activity for hydrogenation. Furthermore, it is found that the Ni/α-Al₂O₃ catalyst has excellent repeatability, and the carbon deposited on the surface of catalyst is negligible.     

木质纤维素生物质催化转化制备苯甲酸

In the present work, we reported a novel route for the conversion of lignocellulosic biomass (sawdust) to a high-value chemical of benzoic acid under atmospheric pressure. The trans- formation involved the catalytic pyrolysis of sawdust into aromatics, the decomposition of heavier alkylaromatics to toluene, and the liquid-phase oxidation of toluene-rich aromatics to benzoic acid. The production of the desired benzoic acid from the sawdust-derived aro- matics, with the benzoic acid selectivity of 85.1 C-mol% and nearly complete conversion of toluene, was achieved using the MnO₂/NHPI catalyst at 100 ℃ for 5 h. The in uence of adding methanol on the catalytic conversion of sawdust to the core intermediate of toluene was also investigated in detail.     

木质素催化转化制备异丙苯

Cumene is an important intermediate and chemical in chemical industry.In this work,directional preparation of cumene using lignin was achieved by a three-step cascade process.The mixture aromatics were first produced by the catalytic pyrolysis of lignin at 450℃ over 1% Zn/HZSM-5 catalyst,monocyclic aromatics with the selectivity of 85.7 wt% were obtained.Then,the catalytic dealkylation of heavier aromatics resulted in benzene-rich aromatics with 93.6 wt% benzene at 600℃ over Hβ catalyst.Finally,the cumene synthesis was performed by the aromatic alkylation,giving cumene selectivity of 91.6 C-mol% using the[bmim]Cl-2AlCl₁₃ ionic liquid at room temperature for 15 min.Besides,adding a small amount of methanol to the feed can efficiently suppress the coke yield and enhance the aromatics yield.The proposed transformation potentially provides a useful route for production of cumene using renewable lignin.     

活化气氛对钼基合成醇催化剂的结构和性能的影响

Activated carbon supported Mo-based catalysts were prepared and reduced under different activation atmospheres, including pure H₂, syngas (H₂/CO=2/1), and pure CO. The catalysts structures were characterized by X-ray diffraction, X-ray absorption fine structure, and in situ diffuse reflectance infrared Fourier transform spectroscopy. The catalytic performance for the higher alcohol synthesis from syngas was tested. The pure H₂ treatment showed a high reduction capacity. The presence of a large amount of metallic Co⁰. and low valence state Mo^φ+ (0<φ<2) on the surface suggested a super activity for the CO dissociation and hydrogenation, which promoted hydrocarbons formation and reduced the alcohol selectivity. In contrast, the pure CO-reduced catalyst had a low reduction degree. The Mo and Co species at the catalyst mainly existed in the form of Mo⁴⁺ and Co²⁺. The syngas-reduced catalyst showed the highest activity and selectivity for the higher alcohols synthesis. We suggest that the syngas treatment had an appropriate reduction capacity that is between those of pure H₂ and pure CO and led to the coexistence of multivalent Co species as well as the enrichment of Mo^δ+ on the catalyst''s surface. The synergistic effects between these active species provided a better cooperativity and equilibrium between the CO dissociation, hydrogenation and CO insertion and thus contributed beneficially to the formation of higher alcohols.     

温和温度与常压下纤维素在其均相水溶液中的降解

Degradation of cellulose to chemicals is one of major routes for biomass conversion. Here, a new simple and two-step method has been developed to convert cellulose in its homogeneously alkaline solution to organic acids under atmospheric pressure at mild temperature. At first, cellulose was degraded to small molecular intermediates at 110 ℃ for 3 h under atmospheric pressure, and then it was oxidized with H₂O₂ at 50 ℃ for 4 h. Under the optimal condition, 73.5% conversion of cellulose could be achieved, and the yield of organic acids was 32.8% (formic acid), 11.6% (lactic acid), and 2.3% (oxalic acid), respectively. It is noteworthy that the new strategy reduces energy consumption in the process of reaction, unlike the hydrothermal reaction under high temperature and high pressure.     

Synthesis of multi-walled carbon nanotubes using CoMnMgO catalysts through catalytic chemical vapor deposition

The Co Mg O and Co Mn Mg O catalysts are prepared by a co-precipitation method and used as the catalysts for the synthesis of carbon nanotubes（CNTs） through the catalytic chemical vapor deposition（CCVD）. The effects of Mn addition on the carbon yield and structure are investigated. The catalysts are characterized by temperature programmed reduction（TPR） and X-ray diffraction（XRD） techniques, and the synthesized carbon materials are characterized by transmission electron microscopy（TEM） and thermo gravimetric analysis（TG）. TEM measurement indicates that the catalyst Co Mg O enclosed completely in the produced graphite layer results in the deactivation of the catalyst. TG results suggest that the Co Mn Mg O catalyst has a higher selectivity for CNTs than Co Mg O. Meanwhile, different diameters of CNTs are synthesized by Co Mn Mg O catalysts with various amounts of Co content, and the results show that the addition of Mn avoids forming the enclosed catalyst, prevents the formation of amorphous carbon, subsequently promotes the growth of CNTs, and the catalyst with decreased Co content is favorable for the synthesis of CNTs with a narrow diameter distribution.The Co Mn Mg O catalyst with 40% Co content has superior catalytic activity for the growth of carbon nanotubes.     

Fabrication of YBCO／YSZ and YBCO／MgO thick films using electrophoretic deposition with top-seeded melt growth process

Superconducting thick films were grown on single crystals MgO and YSZ by electrophoretic deposition with Y_2BaCuO_5(Y211) addition. YBCO thick films were then accomplished by sintering the precursor films above the peritectic temperature. Single crystals of MgO (3×3×0.5 mm^3) were used as top-seed to control crystal structure of the thick films. As shown by scanning electron microscopy, the morphologies of YBCO/YSZ and YBCO/MgO thick films are spherulitic texture and platelet type. The critical temperature is ～89 K for the YBCO/YSZ thick film; the onset transition temperature is 86.4 K and the transition width is ～3 K for YBCO/MgO thick film. The critical current densities (as determined by Bean model) are, in A/cm^2, 3870 (77 K) for YBCO/YSZ thick films and 2399 (77 K) for YBCO/MgO thick films, which are comparable to the best J_c reported of the thick films prepared by the same method.     

Model for increased efficiency of CIGS solar cells by a stepped distribution of carrier density and Ga in the absorber layer

In this paper, several structures for multilayer Cu(In1-xGax) Se2 (CIGS) thin film solar cells are proposed to achieve high conversion efficiency. All of the modeling and simulations were based on the actual data of experimentally produced CIGS cells reported in the literature. In standard CIGS cells with a single absorber layer, the effects of acceptor density and Ga content on device performance were studied, and then optimized for maximum conversion efficiency. The same procedure was performed for cells with two and three sectioned CIGS absorber layers in which Cu and/or Ga contents were varied within each consecutive section. This produces an internal additional electric field within the absorber layer, which resulted in an increase in carrier collection for longer wavelength photons, and hence, improvement in the conversion efficiency of the cell. An increase of approximately 3% in efficiency is predicted for cells with two layer absorbers. For multilayer cells in which Cu and Ga distribution were stepped simultaneously, the improvement could be approximately 3.5%. This improvement is due to; enhanced carrier collection for longer-wavelength photons, and reduced recombination at the heterojunction and back regions of the cell. These results are confirmed by the physics of the cells.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.