The interaction of oxygen molecules with iron films studied with MIES,UPS and XPS

X-ray Photoelectron Spectroscopy (XPS), Metastable Induced Electron Spectroscopy (MIES) and Ultraviolet Photoelectron Spectroscopy (UPS) were applied to study the interaction of oxygen molecules with iron films. Supplementarily, iron oxide was investigated for comparison.With XPS from the Fe 2p_3/2 range contributions of metallic Fe as well as Fe²⁺ and Fe³⁺ can be distinguished. During the interaction with oxygen an oxide film is formed on the iron surface. Nevertheless, XPS still shows metallic contributions even for a surface which is saturated with more than 10⁴ L. The oxide film hinders the dissociation of further impinging oxygen molecules.The interaction of He* atoms with iron oxide surfaces during MIES is dominated by Auger Neutralization. This surprising result follows from the high work function and the fact that intrinsic defects result in a Fermi level pinning to the conduction band.     

Adsorption of O2 and CO2 on the Si(111)-7 × 7 surfaces

The interaction of O₂ and CO₂ with the Si(111)-7 × 7 surface has been studied with X-ray photoelectron spectroscopy (XPS). It was found that both O₂ and CO₂ molecules can readily oxidize the Si(111)-7 × 7 surface to form thin oxide films. Two oxygen species were identified in the oxide film: oxygen atoms binding to on-top sites of adatom/rest atoms with an O 1s binding energy of ~ 533 eV as well as to bridge sites of adatom/rest atom backbonds at ~ 532 eV. These two oxygen species can be interconverted thermally during the annealing process. Due to the low oxidation capability, the silicon oxide film formed by CO₂ has a lower O/Si ratio than that of O₂.     

Surface modification of Ni and Co metal nanowires through MeV high energy ion irradiation

Nickel (Ni) and cobalt (Co) metal nanowires were fabricated by using an electrochemical deposition method based on an anodic alumina oxide (Al₂O₃) nanoporous template. The electrolyte consisted of NiSO₄ · 6H₂O and H₃BO₃ in distilled water for the fabrication of Ni nanowires, and of CoSO₄ · 7H₂O with H₃BO₃ in distilled water for the fabrication of the Co ones. From SEM and TEM images, the diameter and length of both the Ni and Co nanowires were measured to be ∼ 200 nm and 5–10 μm, respectively. We observed the oxidation layers in nanometer scale on the surface of the Ni and Co nanowires through HR–TEM images. The 3 MeV Cl²⁺ ions were irradiated onto the Ni and Co nanowires with a dose of 1 × 10¹⁵ ions/cm². The surface morphologies of the pristine and the 3 MeV Cl²⁺ ion-irradiated Ni and Co nanowires were compared by means of SEM, AFM, and HR–TEM experiments. The atomic concentrations of the pristine and the 3 MeV Cl²⁺ ion-irradiated Ni and Co nanowires were investigated through XPS experiments. From the results of the HR–TEM and XPS experiments, we observed that the oxidation layers on the surface of the Ni and Co nanowires were reduced through 3 MeV Cl²⁺ ion irradiation.     

Characterization of Cu1.4Mn1.6O4/PPy composite electrodes

In this work, we have studied the multilayered polypyrrole(PPy)/oxide composite electrode on glassy carbon (GC) having the structure GC/PPy/PPy(Cu_1.4Mn_1.6O₄)/PPy using X-ray Photoelectron Spectroscopy and Mn K-edge and Cu K-edge XANES and EXAFS. The mixed oxide particles have been incorporated into the PPy matrix simultaneously to the electropolymerization of Py from a solution containing 0.1 M Py + 0.15 M KCl + Cu_1.4Mn_1.6O₄. The XPS data have shown that, prior to the incorporation of the oxide into the PPy matrix, it contains Cu⁺, Cu²⁺, Mn³⁺ and Mn⁴⁺. The XPS, XANES and EXAFS results have shown that when the oxide is incorporated into the PPy matrix, the Cu⁺ present in the original oxide suffers dismutation to give Cu²⁺ and metallic Cu. The metallic Cu is segregated out of the spinel structure. The Mn K-edge XANES and EXAFS data show that, after the incorporation into the PPy matrix, Mn is present as Mn³⁺ and Mn⁴⁺ occupying octahedral sites in a spinel-related structure while the Cu K-edge XANES and EXAFS data indicate that copper occupies tetrahedral sites predominantly in that structure but having a large degree of disorder in the second and higher coordination shells.     

The adsorption of CO2 and CO on Ca and CaO films studied with MIES, UPS and XPS

Metastable Induced Electron Spectroscopy (MIES), Ultraviolet Photoelectron Spectroscopy (UPS), and X-ray Photoelectron Spectroscopy (XPS) are employed to study the adsorption of CO₂ and CO on Ca and CaO films. Ca films are prepared by evaporation of Ca onto clean Si(1 0 0) substrates. CaO films are produced by Ca evaporation in an oxygen atmosphere at a substrate temperature of 670 K. CO₂ interaction with the Ca films is initiated by dissociation of the impinging molecules leading to the formation of Ca-O bonds. These Ca-O bonds are subsequently consumed in the formation of a closed CaCO₃ layer on top of the surface. CO interaction with the Ca surfaces also leads to the dissociation of the molecule and the formation of Ca-O bonds. We find evidence for the subsequent formation of complexes on top of the surface. On CaO surfaces, both CO₂ and CO lead to the formation of a closed CaCO₃ top layer, though displaying very different reaction rates.     

Combined XPS,electrochemical and Kelvin probe measurements of NaY zeolite

In the present study X-ray Photoelectron Spectroscopy (XPS) combined with in situ electrochemical and Kelvin probe measurements was used in order to get a deeper insight on the mechanism of the cation transport through NaY zeolite and the charge transfer through the Au electrode/zeolite interface. It is shown that by imposing a potential gradient across the NaY powder which is sandwiched between two electrodes, Na⁺ ions can be electrically transferred to or from the Au working electrode area, following the direction of the applied potential between the two electrodes. Two peaks corresponding to sodium species were detected by means of in situ XPS investigation during potential application. The first peak of Na1s photoelectrons with binding energy at 1072.2 ± 0.2 eV is attributed to Na adsorbed on the grounded Au electrode with its coverage remaining unchanged upon potential imposition. The second peak is directly associated with Na present in the zeolite and upon potential application its binding energy varies proportionally with the variation of the surface potential measured by Kelvin probe. Upon varying the potential from − 4 to + 4 V between the working and counter electrode, the Na⁺ concentration decreases by ca30% at the Au/zeolite interface. However the invariant amount of Na on the Au electrode under vacuum shows that the variation in Na⁺ concentration is not due to ionic transfer onto the Au surface but instead Na⁺ accumulation can be assumed at the Au/zeolite interface. On the other hand, current or potential application under O₂ atmosphere promotes the electrocatalytic reaction of Na⁺ towards the formation of Na₂O on the Au electrode surface.     

Formation of hydroxyl and water layers on MgO films studied with ambient pressure XPS

To understand the interaction of water with MgO(100), a detailed quantitative assessment of the interfacial chemistry is necessary. We have used ambient pressure X-ray photoelectron spectroscopy (XPS) to measure molecular (H₂O) and dissociative (OH) water adsorption on a 4 monolayer (ML) thick MgO(100)/Ag(100) film under ambient conditions. Since the entire 4 ML metal oxide (Ox) film is probed by XPS, the reaction of the MgO film with water can be quantitatively studied. Using a multilayer model (Model 1) that measures changes in Ox thickness from O 1s (film) and Ag 3d (substrate) spectra, it is shown that the oxide portion of the MgO film becomes thinner upon hydroxylation. A reaction mechanism is postulated in which the top-most layer of MgO converts to Mg(OH)₂ upon dissociation of water. Based on this mechanism a second model (Model 2) is developed to calculate Ox and OH thickness changes based on OH/Ox intensity ratios from O 1s spectra measured in situ, with the known initial Ox thickness prior to hydroxylation. Models 1 and 2 are applied to a 0.15 Torr isobar experiment, yielding similar results for H₂O, OH and Ox thickness changes as a function of relative humidity.     

Interaction of water molecules with bare and deuterated polycrystalline diamond surface studied by high resolution electron energy loss and X-ray photoelectron spectroscopies

In this work we study the interaction of water molecules with deuterated and bare polycrystalline diamond surfaces upon exposure to water vapor by X-ray photoelectron spectroscopy (XPS) and high resolution electron energy loss spectroscopy (HR-EELS). To distinguish the molecular origin of hydrogen bonds (i.e. C–H, O–H, C–O–H, etc.) formed on the diamond surface upon interaction with the water molecules, deuterated and hydrogenated gases were used in our experiments. Diamond films were deposited from a deuterated gas mixture to induce C(di)-D surface terminations. Water adsorption on bare diamond surface gives rise to the appearance of well defined and pronounced C–H and C–OH vibrational HR-EELS peaks and an intense O (1s) XPS peak. These chemically adsorbed water fragments survive 300 °C anneal temperature under ultra-high vacuum conditions. Annealing at 600 °C of the water exposed bare diamond surface results in disappearance of the C–OH vibrational modes alongside with a pronounced reduction of the C–H vibrational modes, whilst only upon annealing to ~ 800 °C the O (1s) XPS peak decreased substantially in intensity. We associate these effects with dissociative adsorption of the water molecules on the bare diamond surfaces.Water exposure onto a deuterated surface, on the other hand, does not result in the appearance of the C–OH vibrational peaks but only to an increase of the C–H vibrational HR-EELS mode along side with the appearance of a weaker XPS O (1) peak, as compared to the same experiment, performed on the bare surface. 300 °C anneal significantly diminishes surface oxygen concentration, as monitored by XPS. We associate these results with H₂O decomposition reactions and also with molecular adsorption on deuterated diamond surfaces. Annealing of the water exposed deuterated diamond surface, results in a pronounced decrease and disappearance of the O (1s) XPS peak at a temperature of ~ 800 °C.     

The interaction between hexahydroxytriphenylene and the rutile TiO2(110)-(1 × 1) surface at UHV conditions

The interaction between 2,3,6,7,10,11-hexahydroxytriphenylene (HHTP) and the rutile TiO₂(110)–(1 × 1) surface under ultrahigh vacuum (UHV) conditions was investigated using X-ray photoemission spectroscopy (XPS), ultraviolet photoemission spectroscopy (UPS), near-edge X-ray absorption fine structure (NEXAFS) spectroscopy, and density functional theory (DFT) calculations. The NEXAFS results showed that HHTP molecules formed a submonolayer and a monolayer that aligned along the [001]-direction with, respectively, a more or less flat downward orientation and a more upright orientation to the TiO₂ surface. The HHTP molecules that aligned along the [001]-direction were most likely grafted onto the TiO₂(110) surface by a bidentate bridge between each of the oxygen atoms of one of the catechol units within the HHTP molecule and two adjacent Ti(5f)⁴⁺ ions on the TiO₂(110) surface. The coordination is non-dissociative in the case of the submonolayer, but dissociative in the monolayer, according to the analysis of the C1s XPS, UPS, C1s NEXAFS data and complementary DFT calculations.     

Proton transfer in water–hydroxyl mixed overlayers on Pt(1 1 1): Combined approach of laser desorption and spatially-resolved X-ray photoelectron spectroscopy

Proton transfer in water–hydroxyl mixed overlayers on a Pt(1 1 1) surface was studied by a combination of laser induced thermal desorption (LITD) method and spatially-resolved X-ray photoelectron spectroscopy (micro-XPS). The modulated pattern OH + H₂O/H₂O/OH + H₂O was initially prepared by the LITD method; vacant area with a 400 μm width was first formed in the mixed OH + H₂O overlayer by irradiation of focused laser pulses, and followed by refilling the vacant area with pure H₂O. Spatial distribution changes of OH and H₂O were measured as a function of time with the micro-XPS technique, which indicated that H₂O molecules in the central region flow into the OH + H₂O region. From quantitative analyses using a diffusion equation, we found that the proton transfer in the mixed overlayer consists of at least two pathways: direct proton transfer from H₂O to OH in the nearest site and the proton transfer to the next-nearest site via H₃O⁺ formation. The time scale of first and second path was estimated to be 5.2 ± 0.9 ns and 48 ± 12 ns at 140 K, respectively. In the presence of water capping layer, however, the rate of proton transfer is reduced by an order of magnitude, which would be explained by peripatetic behavior of proton into H₂O capping layer.     

Diffusion and chemical composition of TiNxOy thin films studied by Rutherford Backscattering Spectroscopy

Thickness and chemical composition of the TiN_xO_y thin films deposited by reactive magnetron sputtering from Ti target at controllable oxygen flow rate were determined by Rutherford Backscattering Spectroscopy (RBS) using 2 MeV He⁺ ions. The films were deposited on carbon foils and amorphous silica (a-SiO₂) substrates at 25 °C and 250 °C. The estimated film thickness is of 75-100 nm. The O/Ti atomic ratio in the films increases up to 1.5 with increasing oxygen flow rate, while that of N/Ti decreases from about 1.1 for TiN to 0.4 at the highest oxygen flow rate. Substantial out-diffusion of carbon from the substrate is observed which is independent of the substrate temperature. Films grown onto a-SiO₂ substrates can be treated as homogeneous single layers without interdiffusion. It is more difficult to determine the nitrogen and oxygen content due to superposition of RBS signals arising from film and substrate. RBS analysis of the depth profile indicates that for the investigated films the carbon diffusion and oxidation not only at the topmost surface layers but over the bulk of the films were found. Comparison with XPS results indicates substantial oxygen adsorption at the surface of TiN_x thin films obtained at zero oxygen flow rate.     

Preparation,surface state and band structure studies of SrTi(1 − x)Fe(x)O(3 − δ) (x = 0–1) perovskite-type nano structure by X-ray and ultraviolet photoelectron spectroscopy

In this report, SrTi_(1 ? x)Fe_(x)O_(3 ? δ) photocatalyst powder was synthesized by a high temperature solid state reaction method. The morphology, crystalline structures of obtained samples, was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and transmission electron microscopy (TEM), respectively. The electronic properties and local structure of the perovskite STF_x (0 ≤ x ≤ 1) systems have been probed by extended X-ray absorption fine structure (EXAFS) spectroscopy. The effects of iron doping level x (x = 0–1) on the crystal structure and chemical state of the STF_x have been investigated by X-ray photoelectron spectroscopy and the valence band edges for electronic band gaps were obtained for STF_x by ultraviolet photoelectron spectroscopy (UPS). A single cubic perovskite phase of STF_x oxide was successfully obtained at 1200 °C for 24 h by the solid state reaction method. The XPS results showed that the iron present in the STF_x perovskite structure is composed of a mixture of Fe³⁺ and Fe⁴⁺ (SrTi_(1 ? x)[Fe³⁺, Fe⁴⁺]_(x)O_(3 ? δ)). When the content x of iron doping was increased, the amount of Fe³⁺ and Fe⁴⁺ increased significantly and the oxygen lattice decreased on the surface of STF_x oxide. The UPS data has confirmed that with more substitution of iron, the position of the valence band decreased.     

Adsorption and reaction of glycine on the rutile TiO2(011) single crystal surface

The adsorption and reaction of glycine on the surface of a rutile TiO₂(011) single crystal has been studied by X-ray Photoelectron Spectroscopy (XPS) and Temperature Programmed Desorption (TPD) techniques. Special attention was given to the formation and stability of the zwitterion structure (⁺NH₃–CH₂–COO^?) in comparison to that of the dissociated structure (NH₂–CH₂–COO^?). Both species have been observed on the surface at 300 K. The zwitterion structure was found less stable than the dissociated structure. This is in line with other experimental results related to proline on rutile TiO₂(110) single crystal [13, 14], glycine on rutile TiO₂(110) single crystal [17, 24] and computational results related to glycine on rutile TiO₂(110) single crystal [25]. By 500 K most of the zwitterion structure has been converted to the dissociated one. TPD results indicated that glycine reacts in a similar way to carboxylic acids on this surface with the main decomposition products being ketene (CH₂=C=O). Other masses left unassigned for were also observed during TPD. The most intense being m/e 55 that might be due to =CH–C(O)N=or C(O)N=CH fragments.     

CRDS of water vapor at 0.1 Torr between 6886 and 7406 cm−1

The absorption spectrum of water vapor in “natural” isotopic abundance has been recorded by high sensitivity CW-Cavity Ring Down Spectroscopy (CW-CRDS) between 6885.79 and 7405.91 cm^?1. This strong absorbing region includes the first hexad of interacting vibrational bands which was previously studied by Fourier Transform Spectroscopy. The achieved sensitivity of the recordings varies from α_min～2×10^–11 to 2×10^?10 cm^?1 allowing us to use a sample pressure of 0.1 Torr, making pressure broadening of the line profile mostly negligible. Weak lines in the vicinity of much stronger lines could then be accurately measured. The weakest lines have intensity on the order of 5×10^–28 cm/molecule at 296 K. A set of 4471 lines were assigned to 4916 transitions of five water isotopologues (H₂ ¹⁶O, H₂ ¹⁸O, H₂ ¹⁷O, HD¹⁶O and HD¹⁸O). A small number of new energy levels was determined mostly for the H₂ ¹⁷O isotopologue. The previous investigations and existing databases are critically evaluated. In particular, a number of corrections and new assignments are proposed for the water list provided by the HITRAN database in the considered region. As a result, a complete list of 12,700 transitions for water in “natural” isotopic abundance is provided as Supplementary Material for the 6885–7408 cm^?1 region.     

Ultrathin Y2O3(111) films on Pt(111) substrates

The growth of ultrathin films of Y₂O₃(111) on Pt(111) has been studied using scanning tunneling microscopy (STM), X-ray photoemission spectroscopy (XPS), and low energy electron diffraction (LEED). The films were grown by physical vapor deposition of yttrium in a 10^? 6 Torr oxygen atmosphere. Continuous Y₂O₃(111) films were obtained by post-growth annealing at 700 °C. LEED and STM indicate an ordered film with a bulk-truncated Y₂O₃(111)–1 × 1 structure exposed. Furthermore, despite the lattices of the substrate and the oxide film being incommensurate, the two lattices exhibit a strict in-plane orientation relationship with the [11?0] directions of the two cubic lattices aligning parallel to each other. XPS measurements suggest hydroxyls to be easily formed at the Y₂O₃ surface at room temperature even under ultra high vacuum conditions. The hydrogen desorbs from the yttria surface above ~ 200 °C.     

Ultrasound-induced emulsification of subcritical carbon dioxide/water with and without surfactant as a strategy for enhanced mass transport

Pulsed ultrasound was used to disperse a biphasic mixture of CO₂/H₂O in a 1 dm³ high-pressure reactor at 30 °C/80 bar. A view cell positioned in-line with the sonic vessel allowed observation of a turbid emulsion which lasted approximately 30 min after ceasing sonication. Within the ultrasound reactor, simultaneous CO₂-continuous and H₂O-continuous environments were identified. The hydrolysis of benzoyl chloride was employed to show that at similar power intensities, comparable initial rates (1.6 ± 0.3 × 10^–3 s^–1 at 95 W cm^–2) were obtained with those reported for a 87 cm³ reactor (1.8 ± 0.2 × 10^–3 s^–1 at 105 W cm^–2), demonstrating the conservation of the physical effects of ultrasound in high-pressure systems (emulsification induced by the action of acoustic forces near an interface). A comparison of benzoyl chloride hydrolysis rates and benzaldehyde mass transport relative to the non-sonicated, ‘silent’ cases confirmed that the application of ultrasound achieved reaction rates which were over 200 times faster, by reducing the mass transport resistance between CO₂ and H₂O. The versatility of the system was further demonstrated by ultrasound-induced hydrolysis in the presence of the polysorbate surfactant, Tween, which formed a more uniform CO₂/H₂O emulsion that significantly increased benzoyl chloride hydrolysis rates. Finally, pulse rate was employed as a means of slowing down the rate of hydrolysis, further illustrating how ultrasound can be used as a valuable tool for controlling reactions in CO₂/H₂O solvent mixtures.     

CO and H2O adsorption and reaction on Au(310)

We have studied desorption of ¹³CO and H₂O and desorption and reaction of coadsorbed, ¹³CO and H₂O on Au(310). From the clean surface, CO desorbs mainly in, two peaks centered near 140 and 200 K. A complete analysis of desorption spectra, yields average binding energies of 21 ± 2 and 37 ± 4 kJ/mol, respectively. Additional desorption states are observed near 95 K and 110 K. Post-adsorption of H₂O displaces part of CO pre-adsorbed at step sites, but does not lead to CO oxidation or significant shifts in binding energies. However, in combination with electron irradiation, ¹³CO₂ is formed during H₂O desorption. Results suggest that electron-induced decomposition products of H₂O are sheltered by hydration from direct reaction with CO.     

Interactions between glycine and amorphous solid water nanoscale films

The interactions of glycine (Gly) with amorphous solid water (ASW) nanolayers (≤ 100 ML), vapor-deposited on single crystalline AlO_x surfaces at 100 K, have been investigated by near-edge X-ray absorption fine structure spectroscopy (NEXAFS) at the oxygen K-edge, temperature-programmed thermal desorption (TPD), X-ray photoelectron spectroscopy (XPS), and temperature-dependent work function measurements. Gly-on-ASW, ASW-on-Gly, and Gly on top of ASW-on-Gly ultrathin films have been fabricated. In contrast to the uniform ASW films grown directly on the hydrophilic AlO_x, water molecules adsorb on the hydrophobic Gly films in the form of 3D ASW clusters. This leads to significant differences in the NEXAFS and work function data obtained from ASW-on-AlO_x and ASW-on-Gly films, respectively. Furthermore, these structural differences influence the chemical state of Gly molecules (neutral vs. zwitterionic) adsorbed on top of ASW films. N1s XPS measurements revealed an increased amount of neutral Gly molecules in the film top-deposited on the ASW-on-Gly structure in comparison to the neutral Gly in the films directly condensed on AlO_x or grown on the ASW substrate. H₂O TPD spectra demonstrate that the crystallization and desorption processes of ASW are affected in a different way by the Gly layers, top-deposited on to ASW-on-AlO_x and ASW-on-Gly films. At the same time, Gly adlayers sink into the ASW film during crystallization/desorption of the latter and land softly on the alumina surface in the form of zwitterionic clusters.     

Rapid preparation of high electrochemical performance LiFePO4/C composite cathode material with an ultrasonic-intensified micro-impinging jetting reactor

A joint chemical reactor system referred to as an ultrasonic-intensified micro-impinging jetting reactor (UIJR), which possesses the feature of fast micro-mixing, was proposed and has been employed for rapid preparation of FePO₄ particles that are amalgamated by nanoscale primary crystals. As one of the important precursors for the fabrication of lithium iron phosphate cathode, the properties of FePO₄ nano particles significantly affect the performance of the lithium iron phosphate cathode. Thus, the effects of joint use of impinging stream and ultrasonic irradiation on the formation of mesoporous structure of FePO₄ nano precursor particles and the electrochemical properties of amalgamated LiFePO₄/C have been investigated. Additionally, the effects of the reactant concentration (C = 0.5, 1.0 and 1.5 mol L⁻¹), and volumetric flow rate (V = 17.15, 51.44, and 85.74 mL min⁻¹) on synthesis of FePO₄·2H₂O nucleus have been studied when the impinging jetting reactor (IJR) and UIJR are to operate in nonsubmerged mode. It was affirmed from the experiments that the FePO₄ nano precursor particles prepared using UIJR have well-formed mesoporous structures with the primary crystal size of 44.6 nm, an average pore size of 15.2 nm, and a specific surface area of 134.54 m² g⁻¹ when the reactant concentration and volumetric flow rate are 1.0 mol L⁻¹ and 85.74 mL min⁻¹ respectively. The amalgamated LiFePO₄/C composites can deliver good electrochemical performance with discharge capacities of 156.7 mA h g⁻¹ at 0.1 C, and exhibit 138.0 mA h g⁻¹ after 100 cycles at 0.5 C, which is 95.3% of the initial discharge capacity.     

Line lists for H218O and H217O based on empirical line positions and ab initio intensities

New line lists for isotopically substituted water are presented. Most line positions were calculated from experimentally determined energy levels, while all line intensities were computed using an ab initio dipole moment surface. Transitions for which experimental energy levels are unavailable use calculated line positions. These line lists cover the range 0.05–20 000 cm^?1 and are significantly more complete and potentially more accurate than the line lists available via standard databases. All lines with intensities (scaled by isotopologue abundance) greater than 10^?29 cm/molecule at 296 K are included, augmented by weaker lines originating from pure rotational transitions. The final line lists contain 39 918 lines for H₂¹⁸O and 27 546 for H₂¹⁷O and are presented in standard HITRAN format. The number of experimentally determined H₂¹⁸O and H₂¹⁷O line positions is, respectively, 32 970 (83% of the total) and 17 073 (62%) and in both cases the average estimated uncertainty is 2×10^?4 cm^?1. The number of ab initio line intensities with an estimated uncertainty of 1% is 16 621 (42%) for H₂¹⁸O and 13 159 (48%) for H₂¹⁷O.