Experimental demonstration of single-mode fiber coupling using adaptive fiber couplerExperimental demonstration of single-mode fiber coupling using adaptive fiber couplerExperimental demonstration of single-mode fiber coupling using adaptive fiber couplerExperimental demonstration of single-mode fiber coupling using adaptive fiber coupler

Coupling plane wave into a single-mode fiber （SMF） with high and steady coupling efficiency is crucial for fiber- based free-space laser systems, where random angular jitters are the main influencing factors of fiber coupling. In this paper, we verified a new adaptive-optic device named adaptive fiber coupler （AFC） which could compensate angular jitters and improve the SMF coupling efficiency in some degree. Experiments of SMF coupling under the angular jitter situation using AFC have been achieved. Stochastic parallel gradient descent （SPGD） algorithm is employed as the control strategy, of which the iteration rate is 625 Hz. In closed loop, the coupling efficiency keeps above 65% when angular errors are below 80/3tad. The compensation bandwidth is 35 Hz at sine-jitter of 15 ~rad amplitude with average coupling efficiency of above 60%. Also, experiments with simulated turbulence have been studied. The average coupling efficiency increases from 31.97% in open loop to 61.33% in closed loop, and mean square error （MSE） of coupling efficiency drops from 7.43% to 1.75%.     

Switchable triple-wavelength erbium-doped fiber laser using a single fiber Bragg grating in polarization-maintaining fiber

A stable and narrow wavelength spacing multiwavelength erbium-doped fiber laser is proposed and demonstrated. The laser can produce simultaneous dual- and triple-wavelength lasing oscillations with a narrow wavelength spacing of less than 0.1 nm via using a single fiber Bragg gratings written in polarization-maintaining (PM) fiber. By adjusting polarization controller, the wavelength spacing of dual-wavelength lasing oscillations can be tuned to as small as 0.032 nm. The maximum amplitude variation for every lasing wavelength is less than 0.5 dB. The room-temperature operation principle is based on the polarization hole burning and deeply saturated effect in an ordinary erbium-doped fiber ring laser (EDFRL). The laser has the advantages of simple all-fiber configuration, low cost, high stability and operating at room temperature.     

Three-level neodymium fiber laser incorporating photonic bandgap fiber

We report a neodymium fiber laser incorporating an all-solid photonic bandgap fiber to suppress the four-level laser transition 4F(3/2)-4I(11/2). We demonstrate lasing at 907 nm on the three-level transition 4F(3/2)-4I(9/2) when pumping at 808 nm. The maximum slope efficiency obtained was 32% with a threshold pump power of 70 mW.     

Coupling characteristics between single-core fiber and multicore fiber

A simple method for coupling between a single-core single-mode fiber and a multicore single-mode fiber is proposed and demonstrated. An effective coupling approach is based on a process of standard splicing and tapering between the single-core single-mode fiber and the multicore single-mode fiber.     

Dispersion compensating fiber used as a transmission fiber: inverse/reverse dispersion fiber

This paper gives an overview of IDF/RDF fiber design and development for submarine system. It starts with the concept of dispersion management line and its difference from the conventional DCF used in a module. Then it reviews the fiber design details and optical properties of various types of fibers used as parts of dispersion management lines. Fiber splicing issues using MFD expanding method and a brief summary of transmission experiments using the dispersion management lines are also included. Finally, we discussed a medial dispersion alternative comprising a positive and negative medial dispersion fiber and future optical properties improvements possibilities.     

Multiwavelength erbium-doped fiber laser using twin-core photonic crystal fiber

Laser Physics - We propose a novel multiwavelength erbium-doped fiber laser incorporating a twin-core photonic crystal fiber (TC-PCF) based Mach-Zehnder interferometer (MZI). TC-PCF based...     

Sensitivity-variable fiber optic pressure sensors using microbend fiber gratings

We report on sensitivity control of fiber optic sensors using microbend long-period fiber gratings. By tuning the phase difference between a pair of periodically aligned rod arrays that sandwiches a single-mode fiber, we can change the coupling strength of the core mode with radiating cladding modes, resulting in variable pressure sensitivity of the transmission power through the fiber. This technique enables control of the measurable range of pressure. When the phase difference is shifted from π toward 0, the measurable range is expanded from 1.7 to 3.3 N/cm and higher using a light-emitting diode as an input light source.     

Analysis of sampled fiber Bragg gratings in polarization-maintaining fiber

A novel type of sampled fiber Bragg gratings （FBGs） written in polarization-maintaining fiber （PMF） is proposed. The reflection spectrum, time delay, and group velocity dispersion （GVD） of the gratings are analyzed. In addition, the reflection spectrum is optimized by apodization. The scheme of multi-wavelength output based on the gratings is proposed, which could be used as a multi-wavelength polarization filter in the density wavelength division multiplexed （DWDM） system.     

基于高非线性光纤的增益谱平坦拉曼光纤放大器研究

针对光纤通信中密集波分复用系统各信道的在线平坦光放大这一光通信问题,提出利用级联高非线性光纤来设计增益平坦的拉曼光纤放大器。对高非线性光纤(As S光纤)拉曼增益谱前后沿进行线性拟合处理,利用不同波长泵浦抽运同种光纤,实现前放大后增益补偿,并考虑信号光损耗不同,在输出端得到了一个近似固定的功率输出值,并分析了影响拉曼光纤放大器输出特性的因素。模拟结果表明:平均增益为20.45 dB,增益平坦度为0.15 dB。     

Optical fiber curvature sensor based on few mode fiber

An optical fiber curvature sensor based on interference between LP₀₁–LP₀₂ modes of a circularly symmetric few mode fiber (FMF) is presented. The device consists of two single-mode fiber and a 10-cm FMF. The two single-mode fiber is offset-spliced to each end of the FMF. When the optical fiber is kept straight and fixed, the interference pattern appears in the transmitted spectrum. As the fiber device is bent, the visibility of the interference fringes (at 1530 nm) decreases, reaching values close to 0.3. The dynamic range of the device can be tailored by the proper selection of the length of FMF. The relationship between the fringe visibility and the curvature is linear while the curvature is between 11 m⁻¹ and 16 m⁻¹. The result indicates that the compact sensor can be used in the measurement of large curvature, which is also important in structural health monitoring.     

微结构光纤预制棒拉制过程的温度场分布

根据非稳态傅里叶热传导方程及微结构光纤(MSF)预制棒的初始条件和边界条件，建立圆柱形坐标系，推导出MSF预制棒的温度场分布方程.计算结果表明：当MSF预制棒在高温炉内的温度场分布接近热传导稳态分布时的下棒速度为制备MSF的最佳速度，此时高温炉的加热温度可降低到MSF预制棒的软化温度，另外，随着MSF空气填充率的增加，MSF预制棒的下棒速度也应加快. 关键词： 微结构光纤 光纤预制棒 温度场分布 热传导     

All fiber passively mode locked zirconium-based erbium-doped fiber laser

All passively mode locked erbium-doped fiber laser with a zirconium host is demonstrated. The fiber laser utilizes the Non-Linear Polarization Rotation (NPR) technique with an inexpensive fiber-based Polarization Beam Splitter (PBS) as the mode-locking element. A 2 m crystalline Zirconia–Yttria–Alumino-silicate fiber doped with erbium ions (Zr–Y–Al-EDF) acts as the gain medium and generates an Amplified Spontaneous Emission (ASE) spectrum from 1500 nm to 1650 nm. The generated mode-locked pulses have a spectrum ranging from 1548 nm to more than 1605 nm, as well as a 3-dB bandwidth of 12 nm. The mode-locked pulse train has an average output power level of 17 mW with a calculated peak power of 1.24 kW and energy per pulse of approximately 730 pJ. The spectrum also exhibits a Signal-to-Noise Ratio (SNR) of 50 dB as well as a repetition rate of 23.2 MHz. The system is very stable and shows little power fluctuation, in addition to being repeatable.     

Single-mode Raman fiber laser based on a multimode fiber

Single-mode operation of a Raman fiber laser based on a multimode fiber has been demonstrated for what is to our knowledge the first time. Single-mode operation was achieved through the beam cleanup effect of stimulated Raman scattering in multimode fibers. The Raman laser, consisting of a 50-microm-core multimode fiber and a multimode Nd:YAG laser pump, produced an output beam corresponding to the fundamental mode of the fiber.     

A 110-W fiber laser with homemade double-clad fiber

A high-power ytterbium-doped fiber laser (YDFL) with homemade double-clad fiber (DCF) is introduced in this letter. The geometric parameter and laser characteristics of the fiber have been studied. With oneend-pumping scheme, pumped by a high-power laser diode with launching power of 280 W, a maximum continuous wave (CW) output of 110 W is obtained with an optical-to-optical efficiency of 40%.     

An acousto-optic Q-switched fiber laser using China-made double-cladding fiber

A simple laser-diode pumped acoustic-optic Q-switched fiber laser is reported by using China-made largemode-area ytterbium-doped fiber. Q-switched pulses with a beam quality factor of M2 ≈ 2 and several hundred nanoseconds pulse duration are achieved at the repetition rate of 1 - 50 kHz. When the repetition rate is 1 kHz, the pulse energy is 0.93 mJ with the pulse duration of 132 ns. Meanwhile, the profile of laser pulses shows some mode-locking phenomena, the mechanism of the phenomena is discussed.     

Switchable multi-wavelength erbium-doped fiber lasers by using cascaded fiber Bragg gratings written in high birefringence fiber

A novel and simple Erbium-doped fiber laser by using cascaded fiber Bragg gratings (FBGs) written in high-birefringence fibers for switchable multi-wavelength operation is proposed. Due to two-peak reflection with orthogonal polarizations of the FBG, the polarization hole-burning effect in the cavity is greatly enhanced. Experimental results show that the stable dual- and three-wavelength lasing operation with very narrow wavelength separation (0.39 nm) can be generated at room temperature. The configuration is simple and flexible. Only by adjusting polarization controllers (PCs), the laser can be switched among the stable single-, dual- and three-wavelength lasing operations.     

Nonlinear-polarization-rotation based multiwavelength erbium-doped fiber lasers with highly nonlinear fiber

A multiwavelength erbium-doped fiber laser based on nonlinear polarization rotation with incorporation of a highly nonlinear fiber has been demonstrated. Stable multi-wavelength operation at room temperature is realized owing to the intensity-dependent transmission in fiber laser with nonlinear-polarization-rotation effect. And benefiting from the four-wave mixing in the highly nonlinear fiber, the uniformity and stabilization of the output multi-wavelength lasing have been greatly improved, in comparison with similar laser using single-mode fiber. Moreover, the wavelength spacing can be arbitrarily chosen according to the requirement through changing the PMF length.     

Ultrawide tunable Er soliton fiber laser amplified in Yb-doped fiber

A Raman-shifted and frequency-doubled high-power Er-fiber soliton laser for seeding an efficient high-power Yb fiber femtosecond amplifier is demonstrated. The Raman-shifted and frequency-doubled Er-soliton laser is tunable from 1.00 to 1.070microm and produces bandwidth-limited 24-pJ pulses at a repetition rate of 50 MHz with a FWHM pulse width of 170 fs at 1.040microm . The Yb(3+) amplifier has a slope efficiency of 52% and generates 3-ps linearly chirped pulses with an average power of 0.8 W at 1.05microm . After pulse compression, 74-fs bandwidth-limited pulses with an average power of 0.4 W and a pulse energy of 8 nJ are generated.     

Frequency-stabilized Yb:fiber comb with a tapered single-mode fiber

We demonstrate a stable Yb:fiber frequency comb with supercontinuum generation by using a specially designed tapered single-mode fiber, in which a spectrum spanning from 500 nm to 1500 nm is produced. The carrier-envelope offset signal of the Yb:fiber comb is measured with a signal-to-noise ratio of more than 40 dB and a linewidth narrower than120 k Hz. The repetition rate and carrier-envelope offset signals are simultaneously phase locked to a microwave reference frequency.