Zn掺杂β-Ga2O3薄膜的制备和特性研究（英文）

β-Ga2O3是一种宽带隙半导体材料,能带宽度Eg≈5.0eV,在光学和光电子学领域有广泛的应用.用射频磁控溅射方法在Si衬底和远紫外光学石英玻璃衬底制备了本征β-Ga2O3薄膜及Zn掺杂β-Ga2O3薄膜,用紫外-可见分光光度计、X射线衍射仪、荧光分光光度计对本征β-Ga2O3薄膜及Zn掺杂β-Ga2O3薄膜的光学透过、光学吸收、结构和光致发光进行了测量,研究了Zn掺杂和热退火对薄膜结构和光学性质的影响.退火后的β-Ga2O3薄膜为多晶结构,与本征β-Ga2O3薄膜相比,Zn掺杂β-Ga2O3薄膜的β-Ga2O3(111)衍射峰强度变小,结晶性变差,衍射峰位从35.69°减小至35.66°.退火后的Zn掺杂β-Ga2O3薄膜的光学带隙变窄,光学透过降低,光学吸收增强,出现了近边吸收,薄膜的紫外、蓝光及绿光发射增强.表明退火后Zn掺杂β-Ga2O3薄膜中的Zn原子被激活充当受主.     

Cu掺杂Ga2O3薄膜的光学性能

采用射频磁控溅射和N2气氛退火处理制备了多晶Ga2O3薄膜和Cu掺杂Ga2O3薄膜.用X射线衍射仪、紫外-可见分光光度计、荧光光谱仪对Ga2O3薄膜和Cu掺杂Ga2O3薄膜的结构和光学性能进行了表征.结果表明,Cu掺杂后Ga2O3薄膜的结晶质量变差,透过率明显降低,吸收率增加,光学带隙减小.本征Ga2O3薄膜在紫外、蓝光和绿光出现了发光带,Cu掺杂后紫外和蓝光发射增强,且在475nm处出现了一个新的发光峰.     

Ga2O3/GaN/蓝宝石模板上β-Ga2O3薄膜的生长

为获得高质量的β-Ga2O3薄膜,将c面蓝宝石上生长的GaN薄膜进行高温氧化制成了Ga2O3/GaN/蓝宝石模板,进而在模板上利用金属有机化学气相沉积(MOCVD)工艺进行了β-Ga2O3薄膜的同质外延。通过X射线衍射仪、原子力显微镜、场发射扫描电子显微镜等方法对样品的晶体结构、表面形貌等性质进行测试与分析。结果表明,该方法获得的β-Ga2O3薄膜晶体质量受GaN薄膜氧化效果与MOCVD工艺条件等因素影响较大。通过优化实验条件,得到了质量较高的β-Ga2O3薄膜。与蓝宝石上或GaN薄膜上异质外延得到的β-Ga2O3薄膜相比,薄膜的晶体质量明显提高。通过对比不同样品的晶体质量、表面形貌和制备过程,发现该方法成功地将β-Ga2O3薄膜在蓝宝石衬底或GaN/蓝宝石模板上异质外延转化为了Ga2O3/GaN/蓝宝石模板上的同质外延,有效地减小了β-Ga2O3薄膜和蓝宝石、GaN之间较大的晶格失配和热失配,有利于提高β-Ga2O3薄膜的晶体质量。     

N掺杂对β-Ga_2O_3薄膜日盲紫外探测器性能的影响

单斜氧化镓(β-Ga_2O_3)材料因其独特而优异的光电特性在日盲紫外探测领域具有广阔的应用前景,受到国内外研究者的广泛关注.本研究工作采用射频磁控溅射技术,在c面蓝宝石衬底上制备了未掺杂和氮(N)掺杂β-Ga_2O_3薄膜,研究了N掺杂对β-Ga_2O_3薄膜结构及光学特性的影响;在此基础上,构筑了未掺杂和N掺杂β-Ga_2O_3薄膜基金属-半导体-金属(metal-semiconductor-metal, MSM)型日盲紫外探测器,并讨论了N掺杂影响器件性能的物理机制.结果表明, N掺杂会导致β-Ga_2O_3薄膜表面形貌变得相对粗糙,且会促使β-Ga_2O_3薄膜由直接带隙向间接带隙转变.所有器件均表现出较高的稳定性和日盲特性,相比之下, N掺杂β-Ga_2O_3薄膜器件能展现出较低的暗电流和更快的光响应速度(响应时间和恢复时间分别为40和8 ms),与氧空位相关缺陷的抑制密切相关.本研究对开发新型的高性能日盲紫外探测器具有一定的借鉴意义.     

NH_3-Ar气氛下制备的Zn_3N_2薄膜的结构和光学性能(英文)

Zn3N2是一种宽带隙半导体材料,在温度高于400°C氧化可生成p型ZnO:N,p型ZnO:N在电子学和光电子学领域有广泛的应用.在NH3-Ar气氛下,用RF磁控溅射金属Zn靶在玻璃衬底上室温制备了Zn3N2薄膜.用紫外-可见分光光度计、X射线衍射仪、X射线光电子谱分析仪、荧光分光光度计对Zn3N2薄膜的光学透过、光学吸收、结构、化学键态和光致发光进行了测量,研究了NH3分压对Zn3N2薄膜的结构和光学特性的影响.XRD分析表明Zn3N2薄膜呈现多晶结构,具有(321)择优取向,Zn3N2(321)衍射峰强度随NH3分压增加而增强.在NH3分压5%～10%制备的Zn3N2薄膜有较低透过率,透过率随NH3分压增加而提高.Zn3N2薄膜是间接带隙半导体,当NH3分压从5%变化到25%时,光学带隙从2.33eV升高到2.70eV.XPS分析表明Zn3N2薄膜在潮湿空气中容易水解.室温下Zn3N2薄膜在437nm和459nm波长出现了发光峰.     

W掺杂对β-Ga_2O_3导电性能影响的理论研究

采用密度泛函理论的平面波超软赝势计算方法,对不同W掺杂浓度下β-Ga2O3的导电性能进行研究.计算了β-Ga2(1-x)W2x O3(x=0,0.0625,0.125)的优化参数、总态密度和能带结构.结果表明,W掺入β-Ga2O3使Ga2(1-x)W2x O3材料的体积增大,总能量升高,稳定性降低.当W的掺杂量较小时,其电子迁移率较大,导电性能也很强.当增加W的掺杂量,Ga2(1-x)W2x O3材料的平均电子有效质量就略有增大,能隙变得越窄,这与实验的变化趋势相一致.     

氧流量对热蒸发CVD法生长β-Ga2O3纳米材料的结构及发光特性的影响

用热蒸发CVD法制备了β-Ga2O3纳米材料, 并用光致发光(PL)方法研究了其发光特性.X射线衍射分析显示, 产物为单斜结构的β-Ga2O3.扫描电子显微镜测试表明:在较小氧流量条件下制备的产物为β-Ga2O3纳米带, 宽度小于100nm, 长度有几微米; 较大氧流量时制备出β-Ga2O3纳米晶粒结构, 晶粒尺度在80-156nm.PL的测试表明: β-Ga2O3纳米结构在波长516nm处有很强的绿色发光带, 且随着氧流量的逐渐增加发光强度逐渐减弱.在氧气氛中900℃退火2h处理后, 发光强度减弱, 进一步证实氧空位缺陷是β-Ga2O3纳米材料发光的主要因素.     

金属有机物化学气相沉积法生长Ga2(1-χ)In2χO3薄膜的结构及光电性能研究

采用金属有机物化学气相沉积(MOCVD)法在蓝宝石(0001)衬底上制备出了Ga2(1-χ)In2χO3(χ=0.1-0.9)薄膜,研究了薄膜的结构、电学和光学特性以及退火处理对薄膜性质的影响.测量结果表明:当In组分χ=0.2时,样品为单斜β-Ga2O3,结构;χ=0.5的样品,薄膜呈现非晶结构,退火处理后薄膜结构得到明显的改善,由非晶结构转变为具有(222)单一取向的立方In2O3结构;对于χ=0.8,薄膜为立方In2O3,结构,退火后薄膜的晶体质量得到提高.在可见光区薄膜本身的透过率均达到了85%以上,带隙宽度随样品中Ga含量的改变在3.76-4.43 eV之间变化,且经退火处理后带隙宽度明显增大.     

N掺杂ZnO薄膜的荧光特性研究

以N2为掺杂源,通过改变O2∶N2比,利用射频磁控溅射法在玻璃衬底上制备了具有[002]择优取向的N掺杂ZnO薄膜,研究了ZnO薄膜的光致发光谱随着N掺入量的不同而变化的规律.结果表明,薄膜主衍射峰为402 nm处的发光峰;由于N掺杂量的不同,有的薄膜在445 nm和524 nm处也有发光发存在,但随着薄膜N含量的不同,其发光峰强度明显不同,其峰位也发生了相应的红移或者蓝移.当O2∶N2为10∶ 15时,制备的薄膜N掺杂量最大,光学性能最好,此工艺为研究ZnO薄膜的缺陷类型及导电类型提供了重要的研究参考.     

MOCVD生长中载气H2对N掺杂ZnO性质的影响

采用MOCVD方法在石英衬底上生长ZnO。实验使用二乙基锌(DEZn)为锌源,N2O作为氧和氮源,H2作为载气。采用PL和Raman光谱方法对ZnO样品进行表征,结果表明H2的加入大幅度减少薄膜中碳的掺入,明显改善了薄膜的光学质量。采用N2O离化技术,可以进一步提高其带边峰的强度,抑制带内发光。XRD测量表明,生长的ZnO薄膜具有c轴择优取向。目前生长高质量N掺杂的p型ZnO薄膜是很困难的,而H2作为载气的加入明显改善了ZnO薄膜的光学性质,在生长过程中加入H2将为获得高质量N掺杂的p型ZnO薄膜提供一种途径。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.