A LEED study of the deposition of carbon on platinum crystal surfaces

The deposition of carbon is studied by LEED on four platinum crystal faces: two low-index surfaces Pt(100), Pt(111)and two stepped surfaces Pt(S) ? [5(100) × (111)], a vicinal of (100), Pt(S)?[6(111) × (100)], a vicinal of (111). Carbon, generated by flowing ethylene onto the hot platinum, causes the formation of a graphitic overlayer and surface rearrangements of the substrate. The threshold temperature for graphitization is the lowest on Pt(100). The overlayer exhibits a single preferred orientation on Pt(100), several orientations on Pt(111) and its vicinal. Ordered carbon structures can be detected on the vicinal of (111) for low carbon doses. The orientations found in spot patterns (perfect registry) or ring-like patterns (imperfect alignment) can be associated with a coincidence-site lattice condition at the Pt/C interface. Faceting is observed except on Pt(111); the vicinal of (100) is particularly unstable. The stepped array on the vicinal of (111) starts to disorder at 350°C and can be converted into a hill and valley configuration at higher temperatures and carbon doses. Implications for catalytic studies are discussed.     

Angular distribution patterns of photoelectrons from orbitals of CO adsorbed on Ni(100), Pt(111) and Pt(110)

The synchrotron radiation from BESSY has been used to measure the photoemission from CO orbitals adsorbed as ordered overlayers on Ni(100) c(2 × 2), Pt(111) c(4 × 2) and Pt(110) (2 × 1)p2mg. Angular distribution patterns of photoelectrons from CO orbitals were recorded with a display-type analyzer. The data were compared with differential photoionization cross sections calculated for free and oriented molecules. The results demonstrate the upright orientation of CO on Ni(100) and Pt(111), while CO on Pt(110) shows a marked difference which can be explained by assuming that the CO molecules are tilted in the [001] directions of Pt(110), yielding a (2 × 1)p2mg superstructure observed in LEED. The tilt angle is estimated to about 20°. The structure model is supported by the shape resonances of the 4σ (5σ) orbitals of CO/Pt(110) as compared to CO/Pt(111).     

Electronically driven phase transitions in a quasi-one-dimensional adsorbate system

A quasi-1D system is prepared using the Pt(110) surface as a template. The electronic surface resonance structure is studied by angle-resolved photoemission spectroscopy for the clean surface as well as for different Bromine coverages. A Fermi surface mapping reveals saddle points at the Fermi level in the interior of the surface Brillouin zone. Correspondingly, a maximum in the static response function χ(q, 0) at the connecting vector q is expected. With 1/2G_x < q < 2/3G_x one observes indeed a 3-fold periodicity around defects and a 2-fold periodicity at low temperature for Θ_Br = 0.5 ML. Cooling of a defect-free c(2×2)-Br/Pt(110) preparation counter-intuitively results in a loss of long-range order. Motivated by DFT calculations this is attributed to an anomalous order-order phase transition into the (2×1) phase accompanied by intense, strongly anisotropic fluctuations within a temperature range of ~200 K. The peculiar behaviour is rationalised in terms of a competition between inter-adsorbate repulsion and an adsorbate triggered 2k_F interaction in the substrate.     

Superlattices formed by electrodeposition of silver on iodine-pretreated Pt(111); studies by LEED,Auger spectroscopy and electrochemistry

Reported are studies by LEED and Auger spectroscopy of silver layers electrodeposited on well-characterized Pt(111) surfaces from aqueous solution. Prior to electrodeposition. the Pt(111) surface was treated with I₂ vapor to form the Pt(111) ($\text{7}\text{×}\text{7}$)R19.1°-I superlattice which protected the Pt and Ag surfaces from attack by the electrolyte and residual gases. Electrodeposition of silver occurred in four distinct ranges of electrode potential. Ordered layers having (3 × 3) and (18 × 18) (coincidence lattice) LEED patterns were formed at all coverages from the onset of deposition to the highest coverages studied, about twenty equivalent atomic layers. Formation of ordered Ag layers has therefore been demonstrated, at least for deposits of limited thickness. Auger spectra revealed that for deposits of a few atomic layers. The iodine layer remained attached to the surface during multiple cycles of electrodeposition and dissolution of silver from iodine-free solution. Each peak of the voltammetric current-potential scan produced a change in the LEED pattern.     

Coverage and adsorption-site dependence of core-level binding energies for tin and lead on Al(111) and Ni(111)

Thin layers (0.2–10 monolayers) of Pb and Sn were prepared on Al(111) and Ni(111) surfaces and characterized by means of LEED, AES, UPS and work-function measurements. The binding energy of the shallow Sn 4d and Pb 5d core-levels was investigated with respect to coverage and adsorption-site-dependent changes. On Al(111) the Sn and Pb monolayers exhibit ordered, two-domain, aligned but not in registry structures. For these layers core-level binding energies were found identical to those of the bulk metals. On Ni(111), Pb gives rise to a 3 × 3 structure, followed then by a 4 × 4 structure at higher coverages. The Pb 5d core-level binding energies shift continuously to higher values. A final shift of 0.42 eV is reached after about 2 monolayers. Sn on Ni(111) exhibits two welll separated peaks lying at 23.70 and 23.97 eV for the $\text{4d}{}_{\mathrm{<mtext>5</mtext><mtext>2</mtext>}}$ line. These two lines can be correlated with two different adsorption sites which have to be assumed for the $\text{(}\text{3}\text{×}\text{3}\text{)R30°}$ and the (2 × 2) structure found at different coverages. The binding energy shifts are discussed in a model based on a Born-Haber cycle.     

Vibrational properties of the Pt(111)-<Emphasis Type="Italic">p</Emphasis>(2 × 2)-K surface superstructure

The vibrational spectra of the Pt(111)-p(2 × 2)-K ordered surface superstructure formed on the platinum surface upon adsorption of 0.25 potassium monolayer are calculated using the interatomic interaction potentials obtained within the tight-binding approximation. The surface relaxation, the dispersion of surface phonons, the local density of surface vibrational states, and the polarization of vibrational modes of adatoms and substrate atoms are discussed. The theoretical results are in good agreement with the recently obtained experimental data.     

Chlorine adsorption on copper: II. Photoemission from Cu(001)c(2 × 2)-C1 and Cu(111)(√3 × √3)R30°-Cl

We have studied high-resolution angle-resolved and photon-polarization dependent photoemission from chlorine adsorbed on Cu(OOl) and Cu(111). Chlorine forms a c(2 × 2) saturation overlayer on Cu(OO1) and adsorbs dissociatively as revealed by LEED and XPS. Several two-dimensional energy bands on Cu(001)c(2 × 2)-Cl could be iden along the $\text{}\text{?}$gG M? and $\text{}\text{?}$gG M? lines of the surface Brillouin zone, their respective mirror symmetry and their orbital character could be determined. An interpretation of these bands is given in terms of the interaction of the ordered overlayers with particular substrate bulk bands. Besides the appearance of adsorbate-induced two-dimensional bands drastic changes are resolved in the substrate d-band emission region. These can be explained almost exclusively by surface umklapp processes involving reciprocal lattice vectors of the ordered adsorbate mesh. Supplementary studies of the Cu(111) (√3 × √3)R30°-Cl system support our ideas. We discuss some important implications of our results for the interpretation of angle-resolved photoenussion spectra from ordered adsorbate layers.     

Adsorption studies on a stepped Pt(111) surface: O2, CO,C2H4, C2N2

A comparative study of the adsorption of several gases on a Pt(S)-[9(111) × (111)] surface was performed using LEED, Auger spectroscopy, flash desorption mass spectrometry and work function changes as surface sensitive techniques. Adsorption was found to be generally less ordered on the stepped surface than on the corresponding flat surface with the exception of the oxygen, where r well ordered overlayer in registry over many terraces was found. Absolute coverages were determined from flash desorption experiments for O₂, CO and C₂N₂. Similar values were obtained as on flat Pt surfaces. Two different surface species seem to be formed upon adsorption of C₂H₄ depending on the adsorption temperature. Contrary to reports from Pt(111) surfaces conversion between the two surface species is heavily restricted on the stepped surface. Work function changes revealed nonlinear adsorbate effects where the adsorbate is electronegative with respect to the substrate. Various adsorption models are discussed in the light of complementary experimental evidence. The results of this study are compared with data available from flat Pt surfaces and possible influences of steps are discussed. No general trends, however, emerge from this comparison and it seems that eventual influences of steps have to be considered individually for every adsorbate.     

Chemisorption and ordering of naphthalene and azulene on Pt(s)[7(111) × (100)]: The effect of periodic defects on long range order

Naphthalene and azulene are molecularly adsorbed on the stepped platinum surface Pt(s)[7(111)×(100)] at room temperature. The (111) terraces of this surface are wide enough to accommodate the unit cell of ordered naphthalene on Pt(111). The periodic defects of this surface disrupt the long range ordering seen for both naphthalene and azulene on Pt(111). There appears to be no correlation between ordered islands on neighboring terraces. In the case of naphthalene, a LEED intensity anomaly allows us to place restrictions on the relative orientations of neighboring naphthalenes and the orientation of the naphthalene islands on each terrace. The naphthalene molecules adjacent to the steps have the long axis of the molecule close to perpendicular to the step.     

Ordered magnetic multilayer nanobowl array by nanosphere template method

Ordered magnetic multilayer [Co/Pt]_n nanobowls have been fabricated over a silicon substrate based on a polystyrene (PS) monolayer film. The ordered PS monolayer was first prepared by the self-assembly technique, which was used as the template for the multilayer film [Co/Pt]_n deposition. The ordered magnetic multilayer [Co/Pt]_n nanobowl array was obtained after the transferring and the selective etching process. The nanobowls show a uniform size and smooth surfaces. The nanobowls stuck to the neighbors and notches were observed in the bowl brims because of the contact points between the closed-packed PS beads. The nanobowls could be separated from their neighbors by thinning the PS beads before the film deposition and no notches were observed anymore. Compared to the chemical method, this method showed more flexible choices of the material to fabricate the nanobowls, which extended the application scope of the nanobowls greatly.     

Modifying Quantum Well States of Pb Thin Films via Interface Engineering

We demonstrate the importance of interface modification on improving electron confinement by preparing Pb quantum islands on Si（111） substrates with two different surface reconstructions, i.e., Si（111）-7 ×7 and Si（111）- Root3×Root3-Pb （hereafter, 7 ×7 and R3）. Characterization with scanning tunneling microscopy/spectroscopy shows that growing Pb films directly on a 7 × 7 surface will generate many interface defects, which makes the lifetime of quantum well states （QWSs） strongly dependent on surface locations. On the other hand, QWSs in Pb films on an R3 surface are well defined with small variations in linewidth on different surface locations and are much sharper than those on the 7 × 7 surface. We show that the enhancement in quantum confinement is primarily due to the reduced electron-defect scattering at the interface.     

Study of chemisorption on copper low-index and stepped surfaces

Adsorption of CHCl₃, O₂, and hydrocarbons has been studied on Cu(111) and stepped surfaces using LEED, AES, and UPS at room temperature. We find that ordered Cl overlayers form upon Cu(111), Cu[3(111) × (100)], and Cu[5(111) × (100)] surfaces upon exposure to CHCl₃. Exposure to O₂ results in rearrangement of the Cu[5(111) × (100)] surface to hill-and-valley regions with large (111) areas, whereas Cu[2(111) × (100)] is stable for the same exposure. The photoemission spectra show new energy levels due to C1 above and below the Cu d band region and a small splitting of the halogen p orbitals. Effects consistent with interaction with the Cu d band are observed. Similar effects are observed with oxygen adsorption. The initial rate of Cl or O₂ chemisorption as measured by photoemission is proportional to the density of steps on these surfaces. Apparently, structural effects play an important role in chemisorption on metals (such as copper) with low density of states at the Fermi energy.     

Triphenylene adsorption on Cu(111) and relevant graphene self-assembly

Investigations on adsorption behavior of triphenylene(TP) and subsequent graphene self-assembly on Cu(111) were carried out mainly by using scanning tunneling microscopy(STM).At monolayer coverage,TP molecules formed a longrange ordered adsorption structure on Cu(111) with an uniform orientation.Graphene self-assembly on the Cu(111) substrate with TP molecules as precursor was achieved by annealing the sample,and a large-scale graphene overlayer was successfully captured after the sample annealing up to 1000 K.Three different Moire patterns generated from relative rotational disorders between the graphene overlayer and the Cu(111) substrate were observed,one with 40 rotation between the graphene overlayer and the Cu(111) substrate with a periodicity of 2.93 nm,another with 70 rotation and 2.15 nm of the size of the Moire supercell,and the third with 100 rotation with a periodicity of 1.35 nm.     

Iodine adsorption on a platinum stepped surface: Pt(s)[6(111) × (111)]

I₂ adsorption on Pt(s)[6(111) × (111)] surfaces under vacuum and atmospheric pressure conditions was studied by LEED, AES and thermal desorption. In contrast to smooth Pt(111), the surface structures were composed of multiple phase domains having (3 × 3) or ($\text{3}\text{×}\text{3}$)R30° local geometry and structural coincidence of the adjacent terraces. No special stability or instability of iodine adsorption at steps was observed.     

Cu在Pt表面扩散激活能和扩散系数的ASED-MO计算

本文应用ASED-MO方法,计算研究了Cu在Pt(111),(100),(110)表面的扩散问题。Cu原子在上述三个表面上的扩散激活能的计算结果分别为0.167eV,0.162eV和0.668eV;300K时的扩散系数分别为3.04×10¹⁰m²/s,3.69×10^-10m²/s和2.42×10^-18m²/s。计算结果表明,Cu原子在Pt(111)和(100)面上,扩散激活能很小,极易迁移,而在(110)面上,激活能较大,扩散系数甚小。     

Diffusion of Au atoms and (5×2) phase formation on the Si(111) (7×7) surface

In this article we investigate the complex 1D mesoscopic model of adatom diffusion and the evolution of an ordered phase on the substrate surface. The analysis of the theoretical model is compared with the experimental results of the spreading of Au adatoms on Si(111)-(7×7) surface. The steady state solutions and their stability conditions are determined within the concept of the traveling-wave solution. It is shown that the formation of the ordered phase (5×2) and the difference in the diffusion of Au on (7×7) and on (5×2) structure results in a sharp edge of diffusion front which corresponds to the coverage of a saturated (5×2) phase. This edge moves linearly in time and α can be determined by experiment. The system of model equations enables the damped waves solution or temporary evolution of two steps.     

Formation of nanoislands in the course of copper deposition on a Cu(111)-(9 × 9)-Ag surface

The process of copper deposition on a structured Cu(111)-(9 × 9)-Ag surface, which represents a (9 × 9) loop dislocation network, is studied by scanning tunneling microscopy. It is found that, when the substrate temperature is 100 K and the copper coverage is 0.1–0.4 of a monolayer, islands of a size no greater than 50 Å are formed at the Ag/Cu(111) interface. The islands remain stable as the sample is heated to room temperature. The shape and boundaries of the nanoislands follow the initial surface superstructure and are determined by the nonuniformity of the interaction of the upper silver layer with the copper substrate. The mechanism of island formation and the origin of their stability are explained in terms of the atom exchange between the adsorbate and substrate.     

Potassium and potassium oxide monolayers on the platinum (111) and stepped (755) crystal surfaces: A LEED,AES, and TDS study

The adsorption of potassium and the coadsorption of potassium and oxygen on the Pt(111) and stepped Pt(755) crystal surfaces were studied by AES, LEED, and TDS. Pure potassium adlayers were found by LEED to be hexagonally ordered on Pt(111) at coverages of θ = _K0.9–;1. The monolayer coverage was 5.4 × 10¹⁴K atoms/cm² (0.36 times the atomic density of the Pt(111) surface). Orientational reordering of the adlayers, similar to the behavior of noble gas phase transitions on metals, was observed. The heat of desorption of K decreased, due to depolarization effects, from 60 kcal/mole at θ_K <0.1, to 25 kcal/mole at θ_K = 1 on both Pt(111) and Pt(755). Exposure to oxygen thermally stabilizes a potassium monolayer, increasing the heat of desorption from 25 to 50 kcal/mole. Both potassium and oxygen were found to desorb simultaneously indicating strong interactions in the adsorbed overlayer. LEED results on Pt(111) further indicate that a planar K₂O layer may be formed by annealing coadsorbed potassium and oxygen to 750 K.     

Superlattices formed by interaction of hydrogen bromide and hydrogen chloride with Pt(111) and Pt(100) studied by LEED,Auger and thermal desorption mass spectroscopy

HBr and HCl react with Pt(111) and Pt(100) surfaces to form adsorbed layers consisting of specific mixtures of halogen atoms and hydrogen halide molecules. Exposure of Pt(111) to HBr yielded a (3×3) LEED pattern beginning at $\text{Θ}{}_{\mathrm{Br}}\text{=}\text{2}\text{9}$ and persisting at the maximum coverage which consisted of $\text{Θ}{}_{\mathrm{<mtext>Br</mtext>}}\text{=}\text{1}\text{3}$ plus $\text{Θ}{}_{\mathrm{<mtext>HBr</mtext>}}\text{=}\text{1}\text{9}$. The most probable structure at maximum coverage, Pt(111)[c(3 × 3)]-(3 Br + HBr), nas a rhombic unit cell encompassing nine surface Pt atoms, and containing three Br atoms and one HBr molecule. On Pt(100) the structure at maximum coverage appears to be Pt(100)[c(2√2 × √2)]R45°-(Br + HBr), $\text{Θ}{}_{\mathrm{<mtext>Br</mtext>}}\text{= Θ}{}_{\mathrm{<mtext>HBr</mtext>}}\text{=}\text{1}\text{4}$; the rectangular unit cell involves four Pt atoms, one Br atom and one HBr molecule. Each of these structures consists of an hexagonal array of adsorbed atoms or molecules, excepting slight distortion for best fit with the substrate in the case of Pt(100). Treatment of Pt(100) with HCl produced a diffuse Pt(100)(2 × 2)-(Cl + HCl) structure at the maximum coverage of Θ_Cl = 0.13, Θ_HCl = 0.11. Exposure of Pt(111) to HCl produced a disordered overlayer. Thermal desorption, Auger spectroscopy and mass spectroscopy provided coverage data. Thermal desorption data reveal prominent rate maxima associated with the structural transitions observed by LEED. Br and HBr, Cl and HCl were the predominant thermal desorption products.     

Template preparation of Pt nanowire array electrode on Ti/Si substrate for methanol electro-oxidation

Platinum (Pt) nanowire array electrode is obtained by dc electrodeposition of Pt into the pores of anodic aluminum oxide (AAO) template on Ti/Si substrate. Transmission electron microscope (TEM) examination shows all the nanowires have uniform diameter of about 30 nm. The brush shapes Pt nanowire array electrode can be seen clearly by field emission scanning electron microscope (FESEM). Pt nanowire array electrode gives the X-ray diffraction (XRD) pattern of face-centered cubic (fcc) crystal structure. The electro-oxidation of methanol on this electrode is investigated at room temperature by cyclic voltammetry. The results demonstrated that the Pt nanowire array electrode will have good potential applications in portable power sources.