二维平板光子晶体直波导的制备和光传输特性的测量

利用聚焦离子束刻蚀的方法在SOI(silicon on insulator)基片上制备了W3型二维光子晶体直波导.观察并测量了近红外激光通过光子晶体波导的散射图形和透过谱.实验结果说明，激光在有引入引出脊形波导的光子晶体直波导中具有很好的传输特性. 关键词： 光子晶体波导 光子带隙 脊型波导     

一种新型无色散慢光光子晶体薄板波导

利用椭圆形孔替代传统光子晶体薄板波导中邻接波导的最内层两排圆孔构成一种新型低损耗光子晶体薄板光波导.该波导的群速度和群速度色散特性强烈依赖于波导中这两排邻接波导的椭圆孔的特性.借助波导导模展开方法,计算得到波导的能带结构和群指数,并分析了它们与椭圆孔的参数关系.通过优化这些椭圆孔的参数,可以增加光子晶体光波导导模在光锥以下的无固有传输损耗带宽,在2—45 nm 的带宽上实现无色散的常数群速度.这些理论结果将为低损耗低色散慢光波导的设计制造提供理论基础. 关键词： 光子晶体薄板波导 群速度 群指数 群速度色散     

光子晶体薄板波导中介质中间层的引入对其特性的影响

光子晶体薄板波导中由于第三组分的引入,波导导模的能带结构、固有损耗、群速度和群速度色散特性被明显改变.随着介质中间层的介电常数的增加,各导模向低频转移,而在这些导模的较高群速度频段内,导模遭受的固有损耗减小.由光子晶体薄板波导的导模能带对引入的介质中间层的敏感程度的分析可知,光子晶体薄板波导的介质薄板厚度越厚,波导宽度越宽那么该结构对中间层的引入越不敏感[1].在人们设计实用的光子晶体薄板波导系统时,介质中间层的引入对该系统的光学性能所带来的影响必须被充分考虑.     

二维介质柱光子晶体波导吸收边界条件

设计优化了用于截断二维正方格子介质柱光子晶体波导的分布布拉格反射波导的结构.二维时域有限差分数值模拟结果显示，在上述两种波导联接处的反射系数可以在大部分光子晶体波导导波的频谱范围内降到1％以下.将这种分布布拉格反射波导和通常的吸收边界条件相结合可以构成用于光子晶体波导的吸收边界条件，其反射率可以降低到-40dB以下，吸收层的厚度可取为晶格长度的1.3倍. 关键词： 吸收边界条件 光子晶体波导 时域有限差分     

二维光子晶体波导与单模平面介质波导间的喇叭波导接头

提出并优化了用于二维介质柱光子晶体波导与单模平面介质波导对接的基于分布布拉格反射波导的喇叭波导接头，提高了这两种波导之间的传输效率.二维时域有限差分仿真结果表明，在大部分光子晶体波导导模的频谱范围内，传输效率高于98％.传输效率最高可以达到99.85％. 关键词： 光子晶体波导 平面介质波导 时域有限差分     

光子晶体波导定向耦合器

在完整二维光子晶体中引入线缺陷后，就形成了光子晶体波导；将时域有限差分方法(FDTD)用于光子晶体波导耦合研究，计算了不同耦合长度情形下的波导各个出口处的透过率，结果表明：光子晶体波导耦合遵循普通介质波导耦合的一般规律，也有定向耦合的功能。进一步的研究表明：对于不同的频率，光子晶体定向耦合器耦合系数是不同的，并且耦合系数和对应的频率之间近似直线关系。     

一种新型无色散慢光光子晶体薄板波导

利用椭圆形孔替代传统光子晶体薄板波导中邻接波导的最内层两排圆孔构成一种新型低损耗光子晶体薄板光波导.该波导的群速度和群速度色散特性强烈依赖于波导中这两排邻接波导的椭圆孔的特性.借助波导导模展开方法,计算得到波导的能带结构和群指数,并分析了它们与椭圆孔的参数关系.通过优化这些椭圆孔的参数,可以增加光子晶体光波导导模在光锥以下的无固有传输损耗带宽,在2—45 nm 的带宽上实现无色散的常数群速度.这些理论结果将为低损耗低色散慢光波导的设计制造提供理论基础.     

用级联缓变结构实现光子晶体波导和传统波导的耦合

为了提高光子晶体波导与传统介质波导的耦合效率,设计了级联缓变结构.先将传统介质波导中的光耦合进尺寸相当的光子晶体W5波导中,然后W5波导中的光被耦合进尺寸较小些的W3波导中,最后光被耦合进尺寸最小的W1波导.各级波导之间由半径逐渐增大的空气孔连接,空气孔半径逐渐变化相当于波导有效折射率在变化,所以各级波导可以看作是被折射率缓变结构连接起来.由于折射率的缓变,使得光从前一级波导耦合进相邻的后一级波导时反射很小,从而能有效地提高耦合效率.数值计算表明,在光子晶体禁带范围内,除了波导有限长度和波导微小禁带造成的微小不通带外,耦合系数一般能达80%左右,最高可达到95%.     

基于硅纳米线波导的两级光子晶体缩束器

鉴于在微观领域光波的缩束对实现光电集成的重要意义,提出了基于硅纳米线波导的两级光子晶体缩束器。其中一级压缩基于W5型和W1型光子晶体波导间的高效耦合。二级压缩则由宽为0.1μm,长为3.06μm的纳米线波导和W1型光子晶体波导构成,通过二者的高效耦合实现光束压缩。当W1型光子晶体波导和纳米线波导间介质柱的半径为0.04μm时,对于1550nm波长的电磁波,缩束器的通光效率可达93.4%,压缩比为16.08,出射光束半峰全宽仅为0.148μm。     

光子晶体中双通道之间能量的转移

从理论和实验上分析了光子晶体中双通道之间能量的转移.在双通道之间引入复合型光子晶体波导,通过调节复合型波导的内部参数，使其满足一定的条件，就可以实现双通道之间能量的完全转移，从而实现了光的定向传输.在实验中，测得了输出端的透过谱. 关键词： 复合型光子晶体波导 能量转移 定向传输     

2D FDTD simulation of low loss small angle bend and Y branch configurations in a photonic crystal waveguide layout with a Mach–Zehnder device design configuration

A technique to produce low loss small angle bends in photonic crystal waveguides is presented. The technique consists of bridging parallel input and output waveguide segments with an inclined waveguide region of the same basic design that has a lateral dielectric shift. Results are presented for waveguides produced by enlarging the silicon gap along the central line, separating air holes in a square array photonic crystal for the TE polarization and an operating wavelength of λ_o = 1.55 μm. This low loss waveguide bending technique is applied to the design of Y branch and Mach–Zehnder photonic crystal structures. Simulation of the performance of the dielectric structures is achieved using 2-D FDTD, similar results are anticipated when applied to 3-D waveguide configurations and for other photonic crystal layouts.     

液晶-金属光子晶体波导的光学特性

运用时域有限差分方法分析了二维液晶-金属光子晶体波导的光学特性。二维正方晶格金属光子晶体波导位于两个电极之间,其背景介质为液晶。通过在电极上施加不同电压,电场诱导液晶取向以改变液晶的折射指数从而改变光子晶体的带隙结构。数值计算结果表明:通过外界电场控制所填充的向列相液晶的方向可以对这种金属光子晶体波导的光学特性进行调节,该波导可用于制作光子晶体光开关等光学器件。     

Adiabatic coupling between conventional dielectric waveguides and waveguides with discrete translational symmetry

We study adiabatic transformation in optical waveguides with discrete translational symmetry. We calculate the reflection and transmission coefficient for a structure consisting of a slab waveguide that is adiabatically transformed into a photonic crystal waveguide and then back into a slab waveguide. The calculation yields high transmission over a wide frequency range of the photonic crystal waveguide band and indicates efficient coupling between the slab waveguide and the photonic crystal waveguide. Other applications of adiabatic mode transformation in photonic crystal waveguides and the coupled-resonator optical waveguides are also discussed.     

Air waveguide in a hybrid 1D and 2D photonic crystal hetero-structure

An air waveguide in hybrid one-dimensional photonic crystal and two-dimensional photonic crystal slab hetero-structure is designed. Light propagating in air waveguide can be confined by two-dimensional photonic crystal slab in x-y plane and one-dimensional photonic crystal films in z direction. Theoretical calculations show that air waveguide in the hetero-structure can achieve some functions as 3D PhCs but could be made more easily than 3D PhCs.     

Numerical studies of 2D photonic crystals: Waveguides,coupling between waveguides and filters

In photonic crystals, light propagation is forbidden in a certain wavelength range, the bandgap. In a two-dimensional crystal composed of parallel high-refractive index rods in a low-index background a line defect can be formed by removing a row of these rods, which can act as a waveguide for frequencies in the bandgap of the crystal. In order to get more insight into the main features of such waveguides we have studied a number of properties, using simulation tools based on the finite difference time domain method and a finite element Helmholtz solver. We show conceptually simple methods for determining the bandgap of the crystal as well as the dispersion of a waveguide for wavelengths in this bandgap. For practical applications, it is also important to know how much light can be coupled into the waveguide. Therefore, the coupling of light from a dielectric slab waveguide into the photonic crystal waveguide has been examined, showing that a coupling efficiency of up to 83% can be obtained between a silicon oxide slab and a waveguide in a crystal of silicon rods. Finally, calculations on an ultra-compact filter based on reflectively terminated side-branches of waveguides (similar to tuned stubs in microwave engineering) are shown and discussed.     

Dispersionless slow light by photonic crystal slab waveguide with innermost elliptical air holes

We report a low-loss photonic crystal slab waveguide formed by deforming the innermost circle air holes in the conventional photonic crystal slab waveguide into elliptical ones. We obtain the photonic bands and group index of guided modes in this photonic crystal waveguide by guided-mode expansion method and investigate the dependence of photonic bands and group index of guided modes on the parameters of the innermost elliptical air holes. The group velocity and group velocity dispersion of this waveguide strongly depend on the innermost elliptical air holes. Photonic crystal slab waveguide with the optimum innermost elliptical air holes possesses a wider single mode region below the light line, in which light can easily propagate without intrinsic loss. At the same time, the guided mode supported by this waveguide has nearly constant group velocity and vanishing group velocity dispersion in a 3-5 nm bandwidth.     

Slight disorder effects in two dimensional photonic crystal structures

In the actual manufacturing process of photonic crystal structure, unavoidable error can generate slight disorder which may influence the performance of photonic crystal based device. In this work, randomly distributional disorders are applied to the air holes in the photonic crystal structure. Based on this, we investigate the influence of the slight disorder on the photonic crystal band structure and the performance of photonic crystal based devices (waveguide and slab cavity). The studies indicate that the slight disorder provides small influence on the band structure of the photonic crystal. But, the random disorder in photonic crystal waveguide may increase transmission loss obviously when the wavelength of the light and the distribution of disorder break the balance of multiple interferences. Also, the slight disorder can reduce the Q factor of the photonic crystal cavity at a certain degree. The studies may provide some useful guides for further photonic crystal device research.     

The study of electro-optical sensor based on slotted photonic crystal waveguide

A compact and sensitive electro-optical sensor based on slotted photonic crystal waveguide (S-PhCW) is demonstrated. The electro-optical sensor can be realized in photonic crystal (PhC) slabs of silicon in Silicon-on-Insulator (SOI). Nonlinear optical polymer is used as infiltration. By applying three-dimensional finite difference time domain (3D-FDTD), the sensitivity and quality factor of electro-optical sensor with different slotted waveguide width are calculated. In addition, sensitivity and the optical properties such as transmission spectrum and field distributions are compared between electro-optical sensor based on line defect photonic crystal waveguide (W1-PhCW) and that based on slotted photonic crystal waveguide (S-PhCW). Simulation results demonstrate that, compared with electro-optical sensor based on line defect photonic crystal waveguide, the sensitivity and quality factor is improved by 30 times and 6.6 times respectively in sensor based on slotted photonic crystal waveguide. Besides, the proposed PhC sensor devices have the advantage of a compact structure with the potential for monolithic integration with optical-to-electrical on-chip conversion and detection.