Noise emission assessment of a hybrid electric mid-size truck

In the attempt to improve urban environmental conditions, city or national incentives encourage the use of cleaner vehicles, including hybrid electric vehicles. This paper explores the actual noise impact of this alternative drivetrain technology on the noise emission of a mid-size delivery truck powered by a parallel hybrid powertrain, compared with an equivalent internal combustion engine truck on the basis of pass-by noise measurements. It investigates jointly the overall emission, the main noise sources and the vertical directivity of the vehicle. The essential benefit results from the existence of a full-electric mode below 50 km/h, with a significant noise reduction which may exceed 8 dB(A) at low constant speed. Even if smaller, this noise advantage is still valuable when the vehicle is accelerating or braking. Due to weaker noise emitted upwards, the benefit should be even greater for residents living on upper building floors. The rolling noise associated with the drive wheel/road contact is the main noise source in all driving situations in electric mode, and beyond 50 km/h in the configurations with engine.     

An experimental procedure to obtain sound power level of tyre/road noise under Coast-By conditions

The rolling noise from tyre–pavement interaction represents the greatest sound contribution from a vehicle when cruising at a high speed. To evaluate the sound levels from this source, existing standardized methods that establish different measurement procedures in both the immediate tyre surroundings, for example the Close-Proximity method, as well as at greater distances, as the Coast-By method. A fundamental parameter that can quantify the sound generation of a source is its sound power level. The standardized methods establish procedures to measure the sound pressure level but not the power level of a tyre as a noise source. For this reason, this paper presents a novel methodology based on sound pressure measurements to obtain the sound power level that a vehicle emits in Coast-By conditions, where noise is generated at tyre/road interaction. The paper describes the testing procedure used to obtain the sound power level, and it is accompanied by a mathematical simulation that studies the feasibility of the proposal. Finally, the proposed methodology is further validated through a field study.     

Investigating generation mechanisms of tyre/road noise by speed exponent analysis

The purpose of this study is to clarify the influence of air-pumping related noise sources on typical tyre/road noise. The aim is to increase the understanding of noise generation mechanisms and catalyse the development of existing tyre/road noise simulation tools. The speed dependency of measured and simulated tyre/road noise is analysed and the results show that a large part of the noise can be explained by a high speed exponent traditionally connected with air-pumping mechanisms. Surprisingly, this is also the case for rough road surfaces which are expected to mainly generate noise by tyre vibrations. It is also found that vehicle wind noise may have a strong influence on the pass-by noise and care must be taken when analysing measurement data of quiet tyre/road combinations. Even simulated tyre/road noise shows higher speed exponents than what is anticipated without the inclusion of any type of air-pumping mechanism in the model. It is concluded that it is unfeasible to separate noise created by tyre vibrations from noise created by air-pumping with a speed exponent analysis due to the overlap in the speed exponents connected with the different generation mechanisms.     

Study to analyze the effects of vehicles and pavement surface types on noise

The effects of vehicles and pavement surface types on noise have been investigated at the Korea Highway Corporation’s Test Road along the southbound side of the Jungbu Inland Expressway, South Korea. The study was conducted in 2005 and 2006 through field measurements at nine surface sections of asphalt concrete and Portland cement concrete pavements using eleven vehicles. For the road noise analysis, the sound power levels (PWLs) of combined noise (e.g., tire/pavement interaction noise and power-train noise together) and tire/pavement interaction noise using various vehicles were calculated based on the novel close proximity (NCPX) and pass-by methods. Then, the characteristics of the PWLs were evaluated according to surface type, vehicle type, and vehicle speed. The results show that the PWLs of vehicles are diversely affected by vehicle speed and the condition of the road surface.     

多通道FxAP算法的电动汽车路噪控制

汽车噪声控制是主动噪声控制领域中经典的问题.伴随着电动化的普及,路噪控制将取代内燃机噪声控制,逐渐成为汽车噪声控制的主要领域.针对传统车内路噪控制系统适应性差、算法收敛速度慢、降噪量不足的问题,该文使用了多通道滤波-x仿射投影(FxAP)算法加快收敛速度,从而实现对噪声的快速追踪并控制.通过搭建了车内多通道头靠噪声控制...     

Towards a model for electric vehicle noise emission in the European prediction method CNOSSOS-EU

The CNOSSOS-EU method is recommended in Europe for environmental noise prediction. In regards to road traffic, it includes vehicle noise emission models implicitly referring to internal combustion vehicles. The development of electrically driven vehicles calls for the future consideration of these vehicles in prediction models. On the basis of experimental data, the study reported in this paper proposes a noise emission model for extending CNOSSOS-EU to light electric vehicles. Correction terms to be applied to the propulsion noise component are determined. Investigations on a sample of tyres with good rolling resistance performance, which is a main tyre selection criterion on these vehicles, indicated that no correction is required for the rolling noise component. Differences between the noise emission from conventional vehicles and electric vehicles are discussed for several road surfaces. Owing to the limited vehicle sample as well as transitional statements, this new model for electric vehicles running at constant speed over 20 km/h should be considered as a first step towards the definition of this vehicle technology in CNOSSOS-EU.     

Noise in heavy goods vehicles

Data are given of noise spectra obtained in the cabs of new, and in-service, heavy goods vehicles having gross vehicle weights up to 40 tons. Comparisons are made between dB(A) and linear sound pressure levels under motorway conditions at 30, 40 and 50 mile/h.The emphasis has been on the collection of data, particularly in the infrasonic region, which lies in the octave bands between 2–20 Hz. The results confirm that high levels of infrasound exist in the cabs and these levels are, possibly, influenced by the ventilation of the cab and the road speed.The data obtained are discussed from the points of view of hearing hazard, impaired vigilance, and possible dangers arising from infrasound. It is concluded that in the noisier vehicles there is certainly a danger to hearing, and from available data on the effects of noise in the laboratory and in industry, there is probably some effect on vigilance. The extent of the possible hazard of infrasound is less well established and a need for further research is pointed out.     

Influence of vehicle noise emission directivity on sound level distribution in a canyon street. Part I: Simulation program test

Simulation programs may be useful tools for controlling an environmental noise. The computer simulation program PROP11 that enables predictions of the time-average sound level within an urban system is used here. A roadway as a noise source is represented by a sum of the sound exposures due to individual vehicle pass-bys. Different representations of equivalent point sources for various classes of vehicles are allowed including directivity characteristics other than omnidirectional. Propagation throughout an urban system contains multi-reflections from the walls and single and double diffraction at their edges. In this paper, the PROP11 program is used to predict the sound level between opposing façades of buildings in a canyon street. A multi-lane road is assumed to contain two classes of vehicles (light and heavy) ones. The equivalent source representing vehicles is defined by the source power spectrum, its position above the ground and directivity characteristics. The consequences of introducing equivalent source directivity are analyzed.     

New vehicle noise emission for French traffic noise prediction

Traffic noise prediction models in France are based on vehicle noise emission values defined by the French Guide du Bruit des Transports Terrestres (Noise Guide for Ground Transport - Noise levels prediction). These emission values are suited for models addressing the noise assessments of road infrastructures and the dimensioning of acoustic protections, needing traffic noise estimations in terms of ?_Aeq over a long period of time (an hour or more).The values, obtained from measurements collected in the 70s, are updated in the publication of a new guide (Methodological Guide, Vehicle noise emissions, to be published), which addresses the road surface influence on tyre/road noise. The emission values are now expressed through the contributions of a power unit component, function of traffic speed, traffic flow type and road declivity, and of a rolling noise component, function of traffic speed and road pavement.The paper outlines the procedures followed to determine the components, gives their numerical values, and illustrates some vehicle noise emissions.     

Statistical tyre/road noise modeling in Hong Kong on friction course

Based on the close proximity (CPX) method specified in ISO/DIS 11819-2, we recorded and analyzed the instantaneous tyre/road sound pressure levels with 9 road sections that are constructed with the same pavement surfacing materials, that is, friction course. A total of 1320 segments were made in urban areas with a pair of SRTT (Standard Road Test Tyre). We tried to relate the tyre/road noise with the instantaneous acceleration, speed, air temperature, road temperature, road gradient, road surface age to develop a multi-variants model. It was subsequently found that a simple tyre/road noise model linking driving speed and acceleration is the best model. The model provides an easy way to estimate the instantaneous tyre/road noise level. As the tyre/road noise is becoming more dominant component of the road traffic noise, our proposed model has the potential to improve the current practice in estimating the road traffic noise.     

Reduction of motor fan noise using CFD and CAA simulations

Motor fans used for cooling electric motors have long been recognized as one of the major noise sources. Current paper focuses on design of motor fan for electric motors that are used in submarines for pumping sea water. Noise reduction at source is very important and the critical task, for under water applications. An attempt has been made for reduction of motor fan noise by modification of noise sources. For this purpose computational fluid dynamics and computational aeroacoustics code FLUENT package is used to identify the noise sources and to know the overall sound pressure level of motor fan. From these results it is observed that aerodynamic noise is the dominate fan noise source. Aerodynamic noise of motor fan can be reduced by modifying fan geometry. The aerodynamic noise level of motor fan has been reduced by replacing the straight blades with various digits of NACA (National Advisory Committee for Aeronautics) 65 series airfoil sections. From the numerical results it is observed that the minimum sound pressure level for NACA 65-010 is 65.4 dB(A). These numerical results are compared with measurements in a semi-anechoic chamber. It is found that there is good agreement between numerical and experimental results.     

Quantitative measurement of pass-by noise radiated by vehicles running at high speeds

It has been a challenge in the past to accurately locate and quantify the pass-by noise source radiated by the running vehicles. A system composed of a microphone array is developed in our current work to do this work. An acoustic-holography method for moving sound sources is designed to handle the Doppler effect effectively in the time domain. The effective sound pressure distribution is reconstructed on the surface of a running vehicle. The method has achieved a high calculation efficiency and is able to quantitatively measure the sound pressure at the sound source and identify the location of the main sound source. The method is also validated by the simulation experiments and the measurement tests with known moving speakers. Finally, the engine noise, tire noise, exhaust noise and wind noise of the vehicle running at different speeds are successfully identified by this method.     

ON THE HORN EFFECT OF A TYRE/ROAD INTERFACE, PART I: EXPERIMENT AND COMPUTATION

Near the tyre/road contact area, the road surface and the tyre belt form a horn-like geometry, which provides a significant amplification mechanism for sound sources. Measurements have been carried out on a stationary tyre placed on a plane surface in an otherwise anechoic chamber. Following the reciprocal theorem a microphone was placed in the road surface near the contact patch and a white noise source was used in the far field. The amplification by the horn effect can then be determined as a function of frequency for an array of microphone positions relative to the contact patch and the centre of the tyre. These experimental measurements show that the horn effect is responsible for about 10-20dB increase in noise level. The amplification function shows a distinct interference pattern for higher frequencies and is independent of the longitudinal source position for low frequencies and source positions close to the contact patch. Numerical calculations using the indirect boundary element method have been carried out. These show excellent agreement with the measurements in the frequency regime of the BEM, i.e., up to 2500 Hz. The dependence of the horn effect on primary geometrical parameters such as the effect of the radius of curvature of the shoulders, the load and the width of the tyre has been investigated experimentally and numerically. The broad features of the horn effect are given by the cylindrical geometry of the tyre. The rounded edges of the tyre tend to increase the levels of the minima and shift them to higher frequencies, while slightly decreasing the levels of the maxima. Shape variations due to load can be accounted for by correcting the source distance to the edge of the formed contact patch. The amplification at low frequencies increases with width, the results collapsing onto a single curve as a function of the dimensionless widthω /λ.     

燃料电池有轨电车声学优化*

基于线路噪声实验,系统测试分析了燃料电池有轨电车的噪声特性,研究了噪声分布以及空气传声、结构传声路径对噪声的贡献。结果表明改善车辆地板、空调、顶板和风挡的隔声性能,尤其是在500～1250 Hz的1/3倍频带范围内的隔声性能将有助于改善车辆内部声学环境。优化燃料电池系统控制,降低冷却单元转速将有助于改善车辆外部声学环境。在此基础上提出减震降噪建议措施,再次进行线路噪声实验,结果表明该措施有效。     

Developing a Hong Kong based speed correction factor by CPX method

A systematic procedure for developing speed correction factor to adjust measured tyre/road noise is proposed in this paper. The draft ISO/CD 11819-2 on the Close-Proximity method to measure tyre/road noise stipulates that speed correction is needed to convert the tyre/road noise level at the sampling speeds to that at the reference speeds. However, the ISO standard does not mention the exact methodology for developing the speed correction factor development, although it recommends local authorities to develop their own. In this study, the tyre/road noise and speed data over 59 runs on a high speed porous asphalt surface is recorded by our CPX trailer in Hong Kong. The instantaneous noise and speed data are then analysed using this proposed procedure and the set of speed correction factor developed is found to be more stable and repeatable.     

基于道路限速策略的规划路网噪声控制*

为缓解交通噪声污染,研究限速方案对噪声的影响,考虑道路限速策略下的阻抗函数,建立基于道路限速的随机用户均衡模型并实现路网交通分配,对规划路网在不同限速策略下的噪声控制规律进行研究。案例结果表明：道路限速控制对象应选取噪声影响道路;道路限速策略控制噪声的主要因素在于降低影响道路上出行车辆的出行速度,控制区域噪声值与路网总出行时间呈线性关系,道路限速80%的情况下,控制区域噪声和路网总出行时间分别降低2.94dB和增加0.66%;路网总噪声排放存在两种不同变化趋势,且与道路等级,绕行系数相关。研究可为从道路规划角度实现交通噪声控制提供有效参考。     

Method of control of the noise level of road vehicles in use

The elaboration of the method of control of noise generated by moving road vehicles has been made possible by using previous measurements of external noise produced by each of those particular vehicles. The results have made it possible to lay down the requirements for the design of specialised instrumentation capable of making such measurements. The advantage of this development is that it makes it possible for inexperienced technical staff to obtain the required acoustic measurements. The previously employed methods of noise prediction have required preceisely defined measuring conditions at the measuring site. The measurements, besides being laborious and time-consuming, give little information concerning the technical condition of the vehicle. On the contrary, with the method presented in this paper it is possible to measure not only the sound pressure level of the general external noise of the vehicle but also the band levels in the two frequency bands which are characteristic of the working engine at a definite speed of rotation, thus giving a preliminary estimation of the vehicle's noisiness. Defining the limiting values for noise level and band levels will enable excessively noisy vehicles to be eliminated.The results of measurements obtained with the above technique for various groups of vehicles are presented in this paper.     

Skirts and barriers for reduction of wayside noise from railway vehicles—an experimental investigation with application to the BR185 locomotive

An experimental investigation to determine the noise reduction efficiency of a number of combinations of vehicle mounted noise skirts and trackside low barriers has been carried out. A 1:4-scale mock-up of the German BR185 locomotive was built. Special care was taken to achieve a realistic representation of the wheel/rail sources, using rotating acoustic source wheels able to imitate the radiation from structural modes and acoustic rail ducts with independently adjustable vertical and lateral slots. The acoustic insertion loss (IL) equivalent to a full-scale microphone position at 25 m distance from the track was determined for the different source components separately. The total IL was obtained from sound power spectra calculated with the TWINS software. Results for the design speed (v=120 km/h) and a case with a lower speed (v=100 km/h) are presented to illustrate the effect of speed on the acoustic IL. The tests were performed in open-air free field conditions. The experimental procedure used in the present investigation gives detailed information on the relative contributions from different source components, which is valuable for further design studies. For the eight combinations reported here, the overall reduction achieved was in agreement with results in the literature. The IL was 2-3 dB(A) for cases with only vehicle skirts and the case with only low track barriers. The combined configurations had insertion losses of 7-13 dB(A).     

Noise abatement schemes for shielded canyons

Access to quiet areas in cities is important to avoid adverse health effects due to road traffic noise. Most urban areas which are or can become quiet (L_A,eq < 45 dB) are shielded from direct road traffic noise. By transfer paths over roof level, many road traffic noise sources contribute to the level in these shielded areas and noise abatement schemes may be necessary to make these areas quiet. Two real life shielded courtyards in Göteborg have been selected as reference cases for a numerical investigation of noise abatement schemes. The selected areas are modelled as canyons with a road traffic noise source modelled outside the canyon by a finite incoherent line source, which is more realistic than both a coherent and an incoherent line source of infinite length. The equivalent sources method has been used for the calculations. For all studied noise abatement schemes in the shielded canyon, the reductions are largest for the lower canyon observer positions. Façade absorption is the most effective when placed in the upper part of the canyon and can typically yield a reduction of 4 dB(A). Constructing 1 m wide walkways with ceiling absorption reduces the level typically by 3 dB(A). These effects are most effective for narrower canyons. For treatments at the canyon roof, reductions are independent of the canyon observer position and amount to 4 dB(A) for a 1 m tall screen and 2 dB(A) for a grass covering of a saddle roof. Downward refracting conditions increase the levels for the lower canyon observer positions and higher frequencies. For sources located in canyons, abatement schemes therein are more effective for noise reduction in the shielded canyon than similar abatement schemes in the shielded canyon itself, given that all contributing source canyons are treated.