Calibration and numerical simulation of Nanoparticle Surface Area Monitor (TSI Model 3550 NSAM)

TSI Nanoparticle Surface Area Monitor (NSAM) Model 3550 has been developed to measure the nanoparticle surface area deposited in different regions of the human lung. It makes use of an adjustable ion trap voltage to match the total surface area of particles, which are below 100 nm, deposited in tracheobronchial (TB) or alveolar (A) regions of the human lung. In this paper, calibration factors of NSAM were experimentally determined for particles of different materials. Tests were performed using monodisperse (Ag agglomerates and NaCl, 7–100 nm) and polydisperse particles (Ag agglomerates, number count mean diameter below 50 nm). Experimental data show that the currents in NSAM have a linear relation with a function of the total deposited nanoparticle surface area for the different compartments of the lung. No significant dependency of the calibration factors on particle materials and morphology was observed. Monodisperse nanoparticles in the size range where the response function is in the desirable range can be used for calibration. Calibration factors of monodisperse and polydisperse Ag particle agglomerates are in good agreement with each other, which indicates that polydisperse nanoparticles can be used to determine calibration factors. Using a CFD computer code (Fluent) numerical simulations of fluid flow and particle trajectories inside NSAM were performed to estimate response function of NSAM for different ion trap voltages. The numerical simulation results agreed well with experimental results.     

Production of Monodisperse Nanoparticles and Application of Discrete-Monodisperse Model in Plasma Reactors

The particle growth in plasma reactor were investigated by using the discrete-monodisperse (D-M) model for various process conditions. The monodisperse large sized particle distribution predicted by the D-M model are in good agreement with the large sized particles by the discrete-sectional model and also in the experiments by Shiratani et al. (1996). Some fractions of the small size particles are in a neutral state or even charged positively, but most of the large sized monodisperse particles are charged negatively. As the mass generation rate of monomers increases, the large sized particles grow more quickly and the production rate of nanoparticles of 100nm by plasma reactor increases. As the initial electron concentration or the monomer diameter increases, it takes longer time for the large sized particles to grow up to 100nm, but the large sized particle concentration of 100nm increases and the resulting production rate of large sized particles of 100nm increases. As the residence time increases, the time for the large sized particles to grow up to 100nm decreases and the large sized particle concentration of 100nm increases and, as a result, the production rate of large sized particles of 100nm increases. We propose that the plasma reactor can be a good candidate to produce monodisperse nanoparticles.     

Size,composition and optical properties of copper nanoparticles prepared by laser ablation in liquids

Colloidal copper nanoparticles were prepared by pulsed Nd:YAG laser ablation in water and acetone. Size and optical properties of the nanoparticles were characterized by transmission electron microscopy and UV–visible spectrophotometry, respectively. The copper particles were rather spherical and their mean diameter in water was 30 nm, whereas in acetone much smaller particles were produced with an average diameter of 3 nm. Optical extinction immediately after the ablation showed surface plasmon resonance peaks at 626 and 575 nm for the colloidal copper in water and acetone, respectively. Time evaluation showed a blue shift of the optical extinction maximum, which is related to the change of the particle size distribution. Copper nanoparticles in acetone are yellowish and stable even after 10 months. In water, the color of the blue-green solution was changed to brown-black and the nanoparticles precipitated completely after two weeks, which is assigned to oxidation of copper nanoparticles into copper oxide (II) as was confirmed by the electron diffraction pattern and optical absorption measurements. We conclude that the ablation of bulk copper in water and acetone is a physical and flexible method for synthesis of stable colloidal copper and oxidized copper nanoparticles. PACS 42.62.-b; 81.07.-b; 61.46.+w     

Deposition of Aerosol Nanoparticles on Flat Substrate Surfaces

The deposition process in a homogeneous electric field, and the subsequent microscopic arrangement of charged, metallic aerosol nanoparticles in the size range of 30 nm on flat substrate surfaces is described. The first aspect of the investigation is the transfer of the particles from a three-dimensional distribution in the gas phase into their arrangement on the substrate surface, in dependence on particle-particle interactions and on Brownian motion. The theoretical results obtained with a trajectory model are compared with experimental results obtained by scanning electron microscope investigation of the deposition patterns. The second aspect of the investigation is the nanostructured arrangement of nanoparticles by means of inhomogeneous electric microfields. We demonstrate a parallel process for the transfer of charge patterns on oxidized silicon surfaces followed by the deposition of monodisperse singly charged nanoparticles, which allows the creation of particle arrangements reaching from 100 nm resolution up to structures in the upper micrometer range. The charge patterns are transferred using a polydimethylsiloxane (PDMS)-stamp, which is covered with a metal layer.     

双峰分布颗粒体系的多角度动态光散射数据反演

采用多角度动态光散射和加权正则化反演方法,对4组模拟的双峰分布颗粒体系(100/600 nm,200/600 nm,300/600 nm和350/600 nm)分别选取1、3、6和10个散射角进行测量.粒度反演结果表明,采用加权正则化方法反演双峰颗粒体系的多角度动态光散射测量数据,可获得峰值位置比小于2∶1且含有大粒径(＞350 nm)颗粒的双峰颗粒粒度分布.采用标准聚苯乙烯乳胶颗粒进行实测的结果验证了这一结论.得到含大粒径颗粒的双峰粒度分布反演结果的原因在于,多角度动态光散射能提供更多的大粒径颗粒的粒度信息,加权正则化反演方法能减少测量数据中的噪声,因而多角度动态光散射测量数据的加权反演能实现峰值位置比小于2∶1且含有大粒径颗粒的双峰颗粒体系的测量.     

Modeling ferrocene reactions and iron nanoparticle formation: Application to CVD synthesis of carbon nanotubes

This paper presents a practically useful model that can predict the formation process and the growth rate of iron nanoparticles from ferrocene. There is a strong need to create such a model that can help improve the process of carbon nanotube (CNT) production by chemical vapor deposition (CVD) and flame synthesis methods. This study serves this purpose. A simple reaction mechanism between ferrocene and hydrogen was proposed based on experimental and theoretical studies conducted by other researchers; then the method of moments with interpolative closure (MOMIC) was applied to compute the size distribution of iron particles. MOMIC was found to reproduce the result of a sectional method with better accuracy than a lognormal method. We simulated the isothermal decomposition of ferrocene and the consequent formation of iron particles with MOMIC; the computed diameter of iron particles agreed reasonably well with experimental data. Analytical solutions for particle diameter were obtained as a function of residence time, assuming monodisperse particles and a constant collision frequency function. They compared very well to the numerical prediction by a monodisperse model and reasonably well to that by MOMIC, suggesting the analytical solutions to be a simple first approximation in assessing the performance of CVD and flame synthesis methods of producing CNTs.     

Nanostructured Deposition of Nanoparticles from the Gas Phase

For many applications, nanoparticles from the gas phase are of interest due to their physical properties. Especially for electronic or optoelectronic applications, the transfer from their random distribution in the gas phase onto flat substrate surfaces has to be controlled because the particles are needed in exactly defined areas on the substrate. We demonstrate a parallel process for the transfer of charge patterns on oxidized silicon surfaces followed by the deposition of monodisperse singly charged nanoparticles, which allows the creation of particle arrangements reaching from 100 nm resolution up to structures in the upper micrometer range. The charge patterns are transferred using a polydimethylsiloxane (PDMS) stamp, which is covered with a metal layer. By applying different voltages to the stamp, negative or positive charges can be transferred. Thus, nanoparticles of different polarities can be guided to certain places.     

Thermodynamics and molecular dynamics investigation of a possible new critical size for surface and inner cohesive energy of Al nanoparticles

In this study, the authors first review the previously developed, thermodynamics-based theory for size dependency of the cohesion energy of free-standing spherically shaped Al nanoparticles. Then, this model is extrapolated to the cubic and truncated octahedron Al nanoparticle shapes. A series of computations for Al nanoparticles with these two new shapes are presented for particles in the range of 1–100 nm. The thermodynamics computational results reveal that there is a second critical size around 1.62 and 1 nm for cubes and truncated octahedrons, respectively. Below this critical size, particles behave as if they consisted only of surface-energy-state atoms. A molecular dynamics simulation is used to verify this second critical size for Al nanoparticles in the range of 1–5 nm. MD simulation for cube and truncated octahedron shapes shows the second critical point to be around 1.63 and 1.14 nm, respectively. According to the modeling and simulation results, this second critical size seems to be a material property characteristic rather than a shape-dependent feature.     

CdSe量子点滤光片尺寸、温度依赖的光学特性

为了缩小光谱仪体积使之适用于军事卫星等领域,本文将胶体量子点作为滤光材料,研究了CdSe胶体量子点滤光片的光学特性。本文采用热注入法合成出了高质量的CdSe胶体量子点,经过对苯二胺消光处理制备成CdSe胶体量子点滤光片。利用透射电子显微镜(TEM)进行样品形貌结构的表征及粒径尺寸的测量,并分别在不同温度下进行了紫外-可见吸收测量和紫外-可见透过率测量。实验表明,在室温情况下,CdSe胶体量子点薄膜的吸收和透过率均随粒径尺寸的增加而增加;在给定粒径尺寸的情况下,CdSe胶体量子点薄膜吸收与透过率曲线的第一激子吸收峰峰位随温度升高发生红移,CdSe胶体量子点薄膜吸收曲线温度每增加10 K红移不超过1 nm,且半峰宽增加;此外,经反复实验验证CdSe胶体量子点滤光片的稳定性及可调谐特性,证实其适合作为截止滤光片。上述结果表明,CdSe胶体量子点滤光片在微型光谱仪方面具有良好的应用价值。     

Measurement of the absorption coefficient of scattering liquid media by the calorimetric method

Using the example of a number of hydrosols (gold nanorods and nanoshells, silver nanoshells, zinc phthalocyanine nanoparticles), we show that the absorption coefficient of a scattering liquid medium can be measured from its heating by a short-time laser irradiation. The degree of heating was determined from expansion of the liquid in an ampoule with a capillary (the principle of liquid thermometer). Irradiation was performed at a wavelength of 671 or 1069 nm. From the transmission of samples of hydrosols at these wave-lengths, the sum of the absorption and scattering coefficients has been determined. To measure the absorption spectra of scattering liquids by this method, a laser with a tunable radiation wavelength is required. In the case of monodisperse colloidal solutions, the method ensures the measurement of the absorption and scattering cross-section ratio of particles.     

Polydisperse spherical colloidal silica particles:Preparation and application

A new industrial method has been developed to produce polydisperse spherical colloidal silica particles with a very broad particle size,ranging from 20-95 nm.The process uses a reactor in which the original seed solution is heated to 100 ℃,and then active silicic acid and the seed solution are titrated to the reactor continuously with a constant rate.The original seeds and the titrated seeds in the reactor will go through different particle growth cycles to form different particle sizes.Both the particles' size distribution and morphology have been characterized by dynamic light scattering(DLS)and the focus ion beam(FIB) system.In addition,the as-prepared polydisperse colloidal silica particle in the application of sapphire wafer's chemical mechanical polishing(CMP) process has been tested.The material removal rate(MRR) of this kind of abrasive has been tested and verified to be much faster than traditional monodisperse silica particles.Finally,the mechanism of sapphire CMP process by this kind of polydisperse silica particles has been investigated to explore the reasons for the high polishing rate.     

Analysis of Particle Size Distribution by Particle Tracking

Particle tracking is performed using a combination of dark field or fluorescence video microscopy with automatic image analysis. The optical detection together with the image analysis software allows for the time resolved localization of individual particles with diameters between 100 and 1000 nm. Observation of their Brownian motion over a set of time intervals leads to the determination of their mean square displacements under the given room temperature and viscosity. Hereby, the radii of a set of particles visible within a given optical frame are derived simultaneously. Rapid data analysis leads to reliable particle size histograms. The applicability of this method is demonstrated on polystyrene latices and PMMA nanospheres with radii between 51 nm and 202 nm.     

Facile synthesis of monodisperse silver nanoparticles by bio-template of squama inner coat of onion

This paper describes a facile sy]nthetic method for preparing monodisperse silver nanoparticles by bio-template of the squama inner coat of onion. The method is able to make silver nanoparticles with average diameters in the range of 4.6–7.9 nm with narrow size distribution. The important factors in the synthesis of monodisperse silver nanoparticles were discussed. The nanoparticles were characterized by transmission electron microscope, Powder X-ray diffraction and UV-Vis spectroscopy. A possible formation mechanism was also proposed. Because of its simple apparatus, high yield, convenient operation and mild conditions, this synthetic method will have potential application in preparing nanoparticles.     

A Comparative Study of the Determination of Ferrofluid Particle Size by Means of Rotational Brownian Motion and Translational Brownian Motion

Two methods, the Toroidal Technique and the Forced Rayleigh Scattering (FRS) method, were used in the determination of the size of magnetic particles and their aggregates in magnetic fluids. The toroidal technique was used in the determination of the complex, frequency dependent magnetic susceptibility, x(w)=x'(w) - ix"(w) of magnetic fluids consisting of two colloidal suspensions of cobalt ferrite in hexadecene and a colloidal suspension of magnetite in isopar m with corresponding saturation magnetisation of 45.5 mT, 20 mT and 90 mT, respectively. Plots of the susceptibility components against frequency f over the range 10 Hz to 1 MHz, are shown to have approximate Debye-type profiles with the presence of relaxation components being indicated by the frequency, f _max, of the maximum of the loss-peak in the x"(w) profiles. The FRS method (the interference of two intense laser beams in the thin film of magnetic fluid) was used to create the periodical structure of needle like clusters of magnetic particles. This creation is caused by a thermodiffusion effect known as the Soret effect. The obtained structures are indicative of as a self diffraction effect of the used primary laser beams. The relaxation phenomena arising from the switching off of the laser interference field is discussed in terms of a spectrum of relaxation times. This spectrum is proportional to the hydrodynamic particle size distribution. Corresponding calculations of particle hydrodynamic radius obtained by both mentioned methods indicate the presence of aggregates of magnetic particles.     

A new dual-type DMA for measuring nanoparticles emitted from combustion engines

A new dual-type differential mobility analyzer (dual-type DMA) was developed in order to detect transient number concentrations of airborne nanoparticles with diameters centralized at around 10 nm (for nuclei mode particles) and 100 nm (for accumulation mode particles) in automobile exhaust gas. The apparatus divides the gas sample into two parts, and each part is sent through one of two coaxially nested sections for analysis. For the scanning mode measurement, the nanoparticles are charged by ²⁴¹Am and their size distributions are determined by varying the applied voltage over 2 min. The transient mode measurement, on the other hand, fixes the voltages for the two sections at peaks near 10 and 100 nm in order to monitor the transient behavior of the exhaust nanoparticles. The measurement principles and design of the dual-type DMA are detailed and the results for time response experiments are presented using model nanoparticles charged by a corona charger. The transient concentrations of the nuclei mode and the accumulation mode particles from a diesel engine were shown to be detected by this method, when ²⁴¹Am was used for charging the particles.This revised version was published online in August 2005 with a corrected issue number.     

Size effect of gold nanoparticles on the electrocatalytic oxidation of carbon monoxide in alkaline solution

This paper describes preliminary findings of Au nanoparticle on glassy carbon (GC) electrodes for electro-oxidation of carbon monoxide in basic conditions. Electrochemical cyclic voltammetric results showed that CO oxidation simultaneously occurred in the anodic and cathodic sweeps during one cycle, and CO electro-oxidation activity was remarkably different in the anode for the different sized Au nanoparticles. The ultrafine catalyst metal particles (2 and 6 nm Au) were more active compared to the larger ones (12, 24 and 41 nm Au). The dependence of the activity on the particle size can be explained in terms of their effect on the number of active sites and the different surface gold oxide species.     

Ultrasonic properties of nanoparticles-liquid suspensions

A polymer colloidal solution having dispersed nanoparticles of Cu and Au metals have been developed using a novel chemical method. Average size of the nanoparticles could be varied in the 4-10 nm range by conducting the reaction at an elevated temperature of 50-70 degrees C. Colloidal solutions of representative concentrations of 0.1-2.0 wt% Cu/Au contents in the primary solutions are used to study the modified ultrasonic attenuation and ultrasonic velocity in PVA polymer molecules on incorporating the Cu/Au particles. A characteristic behaviour of the ultrasonic velocity and the attenuation are observed at the particular temperature/particle concentration. The results demonstrate that the primary reaction during the nanoparticles-PVA colloidal formation occurs in divided groups in small micelles. The results are analyzed predicting the enhanced thermal conductivity of the samples.     

三维时域有限差分法计算金纳米粒子尺寸与SERS活性的关联

通过合成一系列不同粒径(16～160 nm)的金纳米粒子.观察到120～135 nm的金纳米粒子在632.8nm波长激发下具有最高的SERS活性,这与前人报道的电磁场理论及实验的结果不同.利用三维时域有限差分法对金纳米粒子的SERS活性与其尺寸以及入射光波长的关系进行模拟计算.在632.8 nm激发线下,金纳米粒子二聚体体系在粒径为110 nm左右具有最佳增强效应,其光电场耦合最强的热点处的增强因子高达109考虑到体系的平均SERS增强因子通常会比最大值低约2个数量级,计算得到的107的增强因子与实验测量值相符.同时对目前实验上尚难以合成的大尺寸的金纳米粒子进行模拟,结果表明受多极矩和大尺寸效应的影响在粒径220 nm时又出现SERS增强另一峰值.在325 nm的紫外激发线下,计算得到的增强因子仅为102.     

Long‐Term Colloidal and Chemical Stability in Aqueous Media of NaYF4‐Type Upconversion Nanoparticles Modified by Ligand‐Exchange

Surface capping is an essential component of nanoparticles as it provides access to their outstanding properties in the real world. Upconversion nanoparticles are predominantly interesting for use in biological environments, due to their excellent optical properties such as the conversion of near‐infrared excitation light into emissions in the visible or UV range of the spectrum, high photostability, and the absence of any intermittence. One of the most efficient upconversion nanoparticles, consisting of lanthanide doped NaYF₄, suffers from limited stability in aqueous media. This study investigates a set of five types of surface coatings, ranging from small ligands to polymers of different charge and different coordinating groups, on monodisperse 28 ± 0.9 nm sized NaYF₄(Yb,Er) nanoparticles modified by a two‐step ligand exchange mediated by NOBF₄. Information on the long‐term chemical and colloidal stability for highly diluted aqueous dispersions of these particles is acquired by transmission electron microscopy, dynamic light scattering, and luminescence spectroscopy. The findings are of importance for the development of probes and labels based on upconversion nanoparticles for biological applications.     

Light scattering from colloids

This paper presents a review of light scattering results on static and dynamic properties of ordered colloidal suspensions of charged polystyrene particles and fractal colloidal aggregates. Our studies on static structure factor,S(Q), of ordered monodisperse colloidal suspensions and binary mixtures of particles with different particle diameters, measured by angle-resolved Rayleigh scattering will be discussed. This will include determination of bulk modulus using gravitational compression and observation of colloidal glass (inferred from splitting of the second peak inS(Q)). Dynamic light scattering, with real time analysis of scattered intensity fluctuations, is used to get information about Brownian dynamics of the particles. Recent advances in the field of light scattering from colloidal aggregates which show fractal geometry will also be discussed.