掺杂金属颗粒的高分子工质激光推进实验研究

 利用大功率脉冲TEA-CO₂激光器作为光源,对不同元素、浓度以及颗粒直径金属掺入PVC的靶材进行了测试。结果发现,不同元素种类以及不同颗粒直径的金属掺杂后的PVC靶材的冲量耦合系数变化不大,但在不同功率密度处,比冲均有显著提高,其中纳米Fe粉性能最为优异。在功率密度为5×10⁶ W/cm²处,50%纳米Fe粉质量分数的靶材的比冲出现最大值。在大气环境下,对于掺有20%纳米Zn粉质量分数的PVC靶材,其冲量耦合系数随激光功率密度的提高而先升后降,比冲并不优异于比其熔点更高的Fe粉和Ni粉掺杂。     

超声强化合成MgFe2O4纳米颗粒及其机理研究

用超声水解方法制备MgO纳米颗粒,用化学沉淀法制备α-Fe₂O₃纳米颗粒,将MgO/α-Fe₂O₃混合体常温下超声活化2h,400℃固相合成制备出MgFe₂O₄纳米颗粒.通过X射线衍射和透射电子显微镜测试产品的化学成分、晶体结构和形貌尺寸,分析声化学反应机理及其影响因素.研究结果表明:所制备的MgFe₂O₄为尖晶石铁氧体,颗粒尺寸分布在20-30nm之间,粒度分布均匀;超声空化效应提高了化学反应活性、增加反应物的比表面积和反应物之间的接触面积,促进固相合成反应速度,降低反应温度,实现了一般条件下难以完成的化学反应.     

磁控溅射法制备金团簇纳米颗粒及性能表征

 采用磁控溅射法制备金团簇纳米颗粒，用透射电镜(TEM)、X射线衍射(XRD)、紫外可见光分光光度计(UV-Vis)和X射线光电子能谱(XPS)等分析手段对其表征，研究了金团簇纳米颗粒的形貌、颗粒度、结构、光吸收性质及物质成份。研究结果表明：制备的金团簇纳米颗粒呈球形，平均粒径在10 nm左右，粒径分布均匀，无团聚、氧化现象，颗粒的结构为面心立方。在519 nm处出现团簇颗粒的表面等离子共振吸收峰，测试得到Au(4f_7/2)和Au(4f_5/2)电子的结合能分别为83.3 eV和86.9 eV，并且没有出现金的氧化产物。     

由纳米管和纳米颗粒构成的TiO2膜的制备与机理研究

采用聚苯乙烯小球修饰Ti片表面,并进行阳极氧化,制备出一种由纳米颗粒和纳米管构成的TiO₂膜．通过数值模拟,分析了氧化表面附近的局部电场分布对TiO₂膜形貌的影响．结果表明,覆盖物增强了局部电场,从而加快了O^2-与Ti的反应速率,有利于TiO₂的生长;与此同时,[TiF₆]^6-的扩散受到阻碍,使得TiO₂的溶解速率减慢．可见,覆盖物打破了TiO₂纳米管形成的平衡条件,导致纳米颗粒的生成．此外,通过X射线衍射和Raman光谱的测试分析发现,所制备的TiO₂为锐钛矿结构.     

Ag-Cu纳米颗粒修饰的N掺杂TiO2纳米棒阵列及其高效光催化CO2还原应用

本文采用微纳加工方法制备了负载高密度Ag-Cu纳米颗粒的N掺杂TiO₂纳米棒阵列样品. 通过TiO₂的N掺杂,可将其吸光范围调控至与Ag纳米颗粒的等离激元吸收频率相匹配的波段,从而实现复合材料中肖特基结与共振能量转移过程的协同作用. 与此同时,Cu纳米颗粒可以为CO₂还原提供活性位点. 在全谱光照射下,复合样品光催化CO₂还原的活性显著提高,CH₄生成速率可达720 μmol·g^-1·h^-1.     

Enhanced Photoelectrochemical Property of Zn Loaded TiO2 Nanotube Arrays Electrode

采用计时电流法制备了负载Zn纳米粒子的TiO₂纳米管阵列电极．通过阳极氧化法制备TiO₂纳米管阵列电极,然后通过控制计时电流沉积时间来控制负载在TiO₂纳米管上Zn纳米颗粒的沉积量和 沉积尺寸．SEM和XRD分析结果显示,沉积时间为3～5 s时,负载在TiO₂纳米管上的Zn粒子的直径为15～25 nm．UV漫反射光谱发现负载Zn的TiO₂纳米管阵列电极比没有负载的样品吸收487～780 nm的光更强;在高压汞灯照射下,前者比后者的光电流响应提高了50%．     

Mn掺杂对Nd-Fe-B纳米复合永磁合金结构的影响

利用XRD和XAFS技术研究了淬火速度为20m/s的退火和未退火Nd₉Fe_85－xB₆Mn_x(x=0.5,1.0)样品的长程序结构和局域结构.结果表明:初始制备样品,微量Mn原子的掺杂有利于纳米复合Nd-Fe-B磁性材料中Nd₂Fe₁₄B硬磁相和α-Fe软磁相的结晶度增加,而随着Mn掺杂量的增加,Fe原子周围配位有序度升高;退火后,掺杂微量的Mn元素并没有进一步提高Nd₉Fe_85－xB₆Mn_x样品的结晶度,也没有生成新的物相.本文提出,在快淬制备过程中,微量的Mn原子进入纳米复合Nd-Fe-B磁性材料的磁体主相形成亚稳相;退火处理后,Mn原子退出初始的磁体主相而进入颗粒的晶界.     

NiSb纳米颗粒的热液路线制备及电催化析氢性能研究

本文发展了一种简单经济的过渡金属锑化物热液合成路线,在160 oC的温和条件下,由商业易得的乙酰丙酮基镍和三苯基铋在油胺介质中还原制备出NiSb纳米颗粒. 反应中,还原剂甲硼烷-叔丁基胺络合物的使用能够有效促进金属源的快速还原,用以促进NiSb纳米颗粒的生成. 结构表征显示,所制备的NiSb产物为六方相(空间群P6₃/mmc)颗粒状纳米晶,其粒径约为10 nm. 该合成方法可拓展用于CoSb和Ag₃Sb等纳米颗粒的温和制备. 电催化析氢性能研究显示,NiSb纳米颗粒具有良好的电化学析氢反应性能. 结果显示,当阴极电流密度达到50 mA/cm²和10 mA/cm²时所需要的过电位分别为531和437 mV. 同时,NiSb纳米颗粒还具有较小的电荷转移阻抗和优良的循环稳定性能.     

Ag在CeO2-x(111)薄膜上的生长与电子结构

利用XPS和RPES技术研究了CeO_2-x(111)薄膜表面上的氧空位对Ag纳米颗粒的生长和电子结构的影响. XPS结果表明,室温下,Ag纳米颗粒在部分还原的CeO_2-x(111)薄膜上呈三维岛状生长, 并且岛密度比完全氧化的CeO₂(111)薄膜表面上的大, 说明氧空位可以作为Ag纳米粒子生长的中心. Ag3d_5/2芯能级的结合能随着Ag颗粒尺寸的减小而增大, 主要来源于终态效应的贡献. Ag和CeO_2-x     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术，分别沉积Ti和Ti/Al膜，经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序，分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27     

XRD and Mössbauer studies on Pt–Fe nano-particles synthesized by polyol method for cathode catalyst of PEFCS

Pt₅₀–Fe₅₀ nanoparticles were synthesized by the chemically wet process for developing a new high efficiency cathode catalyst in PEFCs. The particle morphology and crystal structure of as synthesized Pt–Fe particles, and electronic state of Fe atoms in them were evaluated using transmission electron microscopy(TEM), X-ray diffraction(XRD) and transmission Mössbauer spectroscopy (TMS), respectively. They are confirmed to be of chemically disordered fcc structure from XRD pattern and the average diameter of them was estimated to be 3.1 nm from both TEM and the width of (111) peak in XRD pattern. From TMS spectrum, it was concluded to consist of mainly the component of Fe oxides connected with the organic ligands according to XPS results mentioned below. But, probably it contains the component for superparamagnetic Pt–Fe nanoparticles. Also the electrocatalytic activity and a hydrogen adsorption/desorption behavior for as synthesized Pt–Fe nanoparticles was observed by cyclic voltammetry and the oxidation of Fe atoms in as synthesized Pt–Fe nanoparticles, Fe metal and Fe oxides were measured.     

Synthesis and characterization of silica-coated nanoparticles of magnetite

Magnetic nanoparticles coated with silica have been subjected of extensive, and, in many aspects, also intensive investigations because of their potential application in different technological fields, particularly in biomedicine. This work was conceived and is being carried out in two main parts: (1) synthesis of the ferrimagnetic nanoparticles, specifically magnetite, and (2) coating these particles with tetraethyl orthosilicate (TEOS). The nanosized magnetite sample was prepared by the reduction–precipitation and the nanomagnetite particles were coated by the sol-gel method, based on the hydrolysis of tetraethyl orthosilicate (TEOS). The so obtained materials were characterized with powder X-ray diffraction (XRD), FTIR spectroscopy, saturation magnetization measurements, and ⁵⁷Fe Mössbauer spectroscopy at room temperature.     

Structural analysis of sonochemically prepared Au/Pd nanoparticles dispersed in porous silica matrix

Bimetallic Au/Pd nanoparticles supported on a silica matrix were prepared by an ultrasonic technique. The samples heat-treated at 100, 200, 300 and 400 degrees C were examined with techniques of XRD (X-ray diffraction), TEM and XAS (X-ray absorption spectrometry) for studying correlation between their structure and the catalytic activity of hydrogenation of cyclohexene. Even after the heat treatment at 400 degrees C, the particles were smaller than 20 nm and well dispersed in the matrix without agglomeration nor sintering. Results of the XRD, TEM and XAS indicated that the as-prepared particles have a core/shell structure of Au/Pd and transform into a random alloy at 300 degrees C. The catalysis seemed to be deactivated by alloying.     

Sonochemical preparation and characterization of photochromic MoO3 nanoparticles

The effect of ultrasound irradiation on molybdenum trioxide has been investigated. Under ultrasonic irradiation, spherical-like MoO₃ nanoparticles were obtained, while bulk-like MoO₃ nanoparticles were prepared without ultrasonic irradiation. The changes in the physicochemical properties of MoO₃ have been investigated using techniques such as X-ray powder diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and ultraviolet and visible spectroscopy (UV-vis). The physicochemical changes of MoO₃ due to ultrasound irradiation have been attributed to the sonochemical cavity collapse onto the molybdenum trioxide particles. The ultrasonically prepared particles can also greatly improve the photochromism efficiency.      

磁性纳米TiO_2/Fe_3O_4的制备及其光催化性能

采用特殊液相沉淀法分两步制备了壳核结构的磁性纳米TiO2/Fe3O4,并讨论了TiO2/Fe3O4比例对其磁性的影响。利用XRD、TEM和VSM对其进行了表征,用它做催化剂,甲基橙溶液为降解目标,在日光作用下对其光催化活性进行了研究,并测出了其回收率。结果表明,在本实验条件下制备的磁性纳米TiO2/Fe3O4表现为超顺磁性,具有较强的光催化活性和较高的回收率。当TiO2∶Fe3O4为4∶1,在450℃焙烧30min条件下得到的催化剂,对20mg/L的甲基橙溶液在60min内降解率高达91.5%,明显高于纯TiO2的催化活性,在外加强磁场的作用下,此催化剂很快从溶液中分离出来,测得其回收率为88.2%。     

Sonochemical synthesis of versatile hydrophilic magnetite nanoparticles

Hydrophilic magnetite nanoparticles in the size range 30-10 nm are easily and rapidly prepared under ultrasonic irradiation of Fe(OH)₂ in di- and tri-ethylene glycol/water solution with volume ratio varying between 7:3 and 3:7.Structural (XRD) and morphological (SEM) characterization reveal good crystalline and homogeneous particles whereas, when solvothermally prepared, the particles are inhomogeneous and aggregated. The sonochemically prepared particles are versatile, i.e. well suited to covalently bind molecules because of the free glycol hydroxylic groups on their surface or exchange the diethylene or triethylene glycol ligand. They can be easily transferred in hydrophobic solvents too.Room-temperature magnetic hysteresis properties measured by means of Vibrating Sample Magnetometer (VSM) display a nearly superparamagnetic character.The sonochemical preparation is easily scalable to meet industrial demand.     

Enhanced photocatalytic activity and stability of nano-scaled TiO2 co-doped with N and Fe

Titanium dioxide (TiO₂) nanoparticles co-doped with N and Fe were prepared via modified sol-gel process. The products were characterized by transmission electron microscopy (TEM), N₂ adsorption, X-ray diffraction (XRD), Raman spectroscopy, UV-vis spectroscopy, photoluminescence (PL), and X-ray photoelectron spectroscopy (XPS). It is shown that the prepared TiO₂ particles were less than 10 nm with narrow particle size distribution. The addition of MCM-41 caused the formation of Ti-O-Si bond which fixed the TiO₂ on MCM-41 surface, thus restricted the agglomeration and growth of TiO₂ particles. The photocatalytic performance in the degradation of methylene blue showed that N, Fe co-doped TiO₂ exhibited much higher photocatalytic activity than doped sample with nitrogen or Fe³⁺ alone under both UV and visible light. N, Fe co-doping decreased the loss of doping N during the degradation reaction, thus increased the photocatalytic stability. It was also found that the nitridation time had significant influence on the photocatalytic activity of prepared TiO₂ catalysts.     

Microstructural properties and local atomic structures of cobalt oxide nanoparticles synthesised by mechanical ball-milling process

In this study, facile preparation of pure and nano-sized cobalt oxides particles was achieved using low-cost mechanical ball-milling synthesis route. Microstructural and morphological properties of synthesised products were characterised by X-ray diffraction (XRD) and transmission electron microscopy (TEM) techniques. XRD results indicated that the fabricated samples composed of cubic pure phase CoO and Co₃O₄ nanocrystalline particles with an average crystallite size of 37.2 and 31.8 nm, respectively. TEM images showed that the resulting samples consisted of agglomerates of particles with average diameter of about 37.6 nm for CoO and 31.9 nm for Co₃O₄. Phase purity of the prepared samples was further investigated due to their promising technological applications. Local atomic structure properties of the prepared nanoparticles were probed using synchrotron radiation-based X-ray absorption spectroscopy (XAS) including X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS). EXAFS data analysis further confirmed the formation of single-phase CoO and Co₃O₄ nanoparticles. In addition, structural properties of cobalt oxide nanoparticles were investigated by performing density functional theory calculations at B3LYP/TZVP level and Born–Oppenheimer molecular dynamics. Theoretical calculations for both prepared samples were found to be consistent with the experimental results derived from EXAFS analysis. Obtained results herein reveals that highly crystalline and pure phase CoO and Co₃O₄ nanoparticles can be synthesised using simple, inexpensive and eco-friendly ball-milling method for renewable energy applications involving fuel cells and water splitting devices.     

Photoluminescent properties of ZnS nanoparticles prepared by electro-explosion of Zn wires

We study the photoluminescent properties of ZnS nanoparticles without the influence of dopants or magnetic impurities. The ZnS nanoparticles reported in this case were synthesized by a novel method of electro-explosion of wire (EEW). The nanoparticles were prepared employing electro-explosion of pure zinc wires in a cell filled with sulfide ions to produce a free-standing compound ZnS semiconductor. To investigate the structural and optical properties, these nanoparticles were characterized by X-ray powder diffraction (XRD), atomic force microscopy (AFM), UV–visible and photoluminescence (PL) spectroscopy. Consistent with the enhancement of the PL intensity of the 443 nm peak due to deep blue emission of ZnS particles, the XRD of the nanoparticles reveals a hexagonal phase of ZnS nanocrystallites prepared by our novel synthesis technique.      

溶胶凝胶法制备Ti1-xFexO2纳米颗粒及磁性能研究

采用溶胶凝胶法制备了稀磁半导体Ti1-xFexO2(x=0～0.050)的纳米颗粒,在氩气氛围中以500℃对样品进行退火处理,并通过差热/热重综合热分析仪(TG-DTA)、X射线衍射仪(XRD)、拉曼光谱(Raman)分析了纳米颗粒的结构和相变温度.使用振动样品磁场计(VSM)测试了样品的磁性能.研究发现:经500℃氩...