热处理对ZnO:Zn荧光薄膜结晶性能的影响

用热处理方法对电子束蒸发制备的ZnO:Zn荧光薄膜分别进行400,600℃退火处理。采用X射线衍射、X射线光电子能谱、扫描电子显微镜、光致发光光谱等方法,表征了ZnO:Zn荧光薄膜的结构、成分、形貌、发光性能。在ZnO:Zn荧光薄膜的X射线衍射谱和扫描电子显微镜照片中,可以看出经退火处理后结晶状况大大改善,多晶结构趋于规则,晶粒更加均匀且膜层结构更加致密。在ZnO:Zn荧光薄膜的光致发光谱中,检测到490nm处发光峰,认为一价氧空位(V_O)充当发光中心,且薄膜的光致发光强度受热处理温度的影响很大。实验表明随着退火温度的升高,薄膜的结晶程度提高,弥补了薄膜晶体表面的表面缺陷,薄膜的发光性能不断提高。     

热处理对ZnO∶Zn荧光薄膜结晶性能的影响

用热处理方法对电子束蒸发制备的ZnO∶Zn荧光薄膜分别进行400,600℃退火处理。采用X射线衍射、X射线光电子能谱、扫描电子显微镜、光致发光光谱等方法,表征了ZnO∶Zn荧光薄膜的结构、成分、形貌、发光性能。在ZnO∶Zn荧光薄膜的X射线衍射谱和扫描电子显微镜照片中,可以看出经退火处理后结晶状况大大改善,多晶结构趋于规则,晶粒更加均匀且膜层结构更加致密。在ZnO∶Zn荧光薄膜的光致发光谱中,检测到490 nm处发光峰,认为一价氧空位(VO)充当发光中心,且薄膜的光致发光强度受热处理温度的影响很大。实验表明随着退火温度的升高,薄膜的结晶程度提高,弥补了薄膜晶体表面的表面缺陷,薄膜的发光性能不断提高。     

衬底对原位氧化制备的ZnO薄膜结构和光学性质的影响

 采用射频反应溅射法在不同衬底上制备Zn₃N₂薄膜，然后对其原位氧化制备ZnO薄膜。利用X射线衍射分析(XRD)、扫描电子显微镜(SEM)和光致发光谱(PL)等表征技术研究了不同衬底对ZnO薄膜的结晶特性和发光性能的影响。XRD研究结果显示:Zn₃N₂薄膜在500 ℃原位氧化3 h后完全转变为ZnO薄膜，在玻璃和熔融石英衬底上制备的多晶ZnO薄膜无择优取向，而单晶硅（100）衬底上的多晶ZnO薄膜具有较好的沿（002）方向的择优取向。PL测试结果显示:硅和熔融石英衬底上的多晶ZnO薄膜发光性能良好，激子复合产生的紫外发光峰很强，且半高宽较窄，而来自于深能级发射的绿色发光峰很弱；而玻璃衬底上的多晶ZnO薄膜发光性能较差。     

掺杂偶氮化合物的PMMA光折变聚合物的拉曼光谱分析

光折变聚合物具有良好的光折变效应,采用以惰性聚合物PMMA为基体,掺杂偶氮化合物染料的光折变聚合物具有较好的光学非线性和稳定性。文章主要介绍使用激光拉曼光谱仪对合成聚合物的各单体和聚合物薄膜进行拉曼光谱扫描,对比分析各个单体成分的特征谱峰与聚合物薄膜特征谱峰,肯定了实验中得到的光折变聚合物薄膜与理论上要求得到的一致性。     

纳米SiCN薄膜的制备和光致发光

采用磁控溅射技术制备了SiCN薄膜,利用傅里叶红外光谱仪、扫描探针显微镜、荧光分光光度计对薄膜结构、表面形貌、光致发光进行了表征.结果表明SiCN薄膜有良好的发光性质,通过对薄膜的红外光谱及光致发光谱分析可知,当氩气和氮气流量比为4:1时,最有利于SiCN薄膜的生成,PL发光峰强度也达到最大值,SiCN薄膜的光发射主要来源于带-带直接辐射复合及导带底到缺陷态辐射跃迁.     

衬底温度对ZnMgO薄膜结构和光致发光性能的影响

利用超声喷雾热解方法以不同的沉积温度(450～550℃)在石英衬底上制备出一系列ZnMgO薄膜。采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)和光致发光谱(PL)表征了样品的晶体结构、表面形貌和光学性能。结果表明衬底温度对薄膜结构性能和光学特性影响显著。所有薄膜都呈六角纤锌矿多晶结构,其中在530℃条件下制备的样品C轴择优最明显,晶粒尺寸均匀,表面形貌平整,结晶质量最好。薄膜的光致发光谱显示随着温度的升高深能级跃迁范围逐渐减小,近紫外带边发光峰逐步出现。衬底温度为530℃时在374.5nm处出现了明显的近紫外发光峰,且几乎没有明显的深能级跃迁出现。     

组合方法筛选新型发光材料

结合作者课题组开展的工作,简要介绍了组合方法在发光材料研究中的应用.包括:适用于发光材料库合成的组合溶液喷射和原位掩模薄膜顺序沉积技术;应用于发光材料库高通量筛选的照相术、组合扫描光谱和组合真空紫外发光表征系统.列举了组合方法在稀土聚合物敏化发光材料、真空紫外发光材料和长余辉发光材料等研究中的应用.     

高铁酸钾降解苯并芘的荧光光谱研究

在优化的反应条件下,研究了高铁酸钾与苯并芘(BaP)的降解反应过程,通过联合应用同步,三维(EEM),时间扫描及荧光光度定量等多种荧光光谱分析方法所提供的多角度的荧光光谱信息,揭示了BaP分子在降解过程中浓度随时间变化规律,尤其高铁酸钾与BaP作用过程的动力学特征。同步荧光和三维荧光光谱共同揭示出,高铁酸钾在20s内能降解91%的BaP,60s以后反应趋于缓慢的变化规律;由时间扫描荧光光谱结合发射和同步两种荧光光度定量方法,便捷地获得了高铁酸钾与BaP的反应过程中的动力学方程:ln(F0/Ft)=0.563 2t+0.171 2,(R2=0.994 2),由此推测高铁酸钾与BaP的反应过程符合一级反应动力学规律。为研究高铁酸钾降解其他污染物反应过程的机理提供了十分有益的参考。     

Zn1-xMgxO薄膜的光致发光特性研究

采用脉冲激光沉积方法在单晶Si(100)衬底上制备出c轴取向的Zn1-xMgxO单晶薄膜,通过荧光光谱仪研究了薄膜的光致发光特性.实验结果表明,Mg含量增加,Zn1-xMgxO单晶薄膜的紫外发光峰蓝移,发光峰强度减弱,缺陷发光强度增强.同时发现,由于Mg的掺杂,引入了一些束缚能较大的局域束缚态.对于氧气氛下制备的样品,实验发现紫外峰和绿光带发光峰同时增强,但是R值减小,紫外峰红移.对绿光发光机理研究发现,绿光发光带主要与锌空位、氧间隙(Oi)或锌位氧(OZn)等缺陷有关,它是由多个缺陷发光峰组成,各缺陷发光峰强度相对变化导致了绿光发光带的整体移动.     

花状的氧化锌纳米结构的制备及其光学性能

以氢氧化钠和六水合硝酸锌为反应物,在未使用任何表面活性剂的简单反应体系中制得了玫瑰花状ZnO纳米结构,采用X射线衍射(XRD)、扫描电子显微镜(SEM)和室温荧光光谱对产物的晶体结构、形貌和发光性质进行了表征和分析.测试结果表明,所得产物为六方纤锌矿结构ZnO纳米材料,产物结晶完整,尺寸较均匀.这种简单水热法制备的ZnO纳米材料仅在384nm处具有一个较强的紫外发光峰,而在黄绿区几乎没有发光峰,进一步证明了所得样品结晶良好,没有缺陷和空位.以上结果表明所制备的氧化锌纳米材料具有优异的紫外光发射能力.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.