ZnCoO稀磁半导体的室温磁性

采用固相反应法，将ZnO和Co₂O₃粉末按不同的成分配比混合，制备了稀磁半导体Zn_1-xCo_xO (x=0.02,0.06,0.10)材料.并使用H₂气氛退火技术对样品进行了处理，得到了具有室温铁磁性的掺Co氧化锌稀磁半导体.利用全自动X射线衍射仪、X射线光电子能谱仪、高分辨透射电子显微镜和超导量子干涉器件磁强计对样品的结构、晶粒的尺寸、微观形貌以及磁性等进行了测量和标度. 关键词： 稀磁半导体 氧化锌 掺杂 固相反应法     

表面活性剂和n型载流子对钴掺杂氧化锌薄膜铁磁性的双重调控

本文提出了一种利用表面活性剂钝化和电子载流子掺杂来调制钴掺杂氧化锌稀磁半导体薄膜固有铁磁性的"双重操纵效应"新方法.第一性原理计算表明,氢表面钝化作为薄膜表面Co-O-Co磁耦合的磁开关,可以控制掺杂钴原子的自旋极化.同时,电子载流子掺杂可以进一步用作类层状铁磁性媒介来调节薄膜内部原子层的铁磁性.该双重操纵效应揭示了n型钴掺杂氧化锌稀磁半导体薄膜的本质铁磁性来源,并且还有可能用作其他n型稀磁半导体氧化物薄膜增强铁磁性的替代策略.     

表面活性剂和n型载流子对钴掺杂氧化锌薄膜铁磁性的双重调控（英文）

本文提出了一种利用表面活性剂钝化和电子载流子掺杂来调制钴掺杂氧化锌稀磁半导体薄膜固有铁磁性的"双重操纵效应"新方法.第一性原理计算表明,氢表面钝化作为薄膜表面Co-O-Co磁耦合的磁开关,可以控制掺杂钴原子的自旋极化.同时,电子载流子掺杂可以进一步用作类层状铁磁性媒介来调节薄膜内部原子层的铁磁性.该双重操纵效应揭示了n型钴掺杂氧化锌稀磁半导体薄膜的本质铁磁性来源,并且还有可能用作其他n型稀磁半导体氧化物薄膜增强铁磁性的替代策略.     

掺钴氧化锌稀磁半导体的SEM及X射线能谱微分析研究

采用水热法,以CoCl2·6H2O为前驱物,KOH作为矿化剂合成了掺钴氧化锌稀磁半导体晶体.利用扫描电子显微镜(SEM)及X射线能谱仪(XREDS)对合成晶体的微观形貌、表面及内部掺杂元素Co的相对含量和分布的均匀性进行了研究.研究结果表明:水热法合成的掺Co氧化锌晶体具有多种微观形貌,较大的晶体具有极性生长特性.随晶体形貌不同,显露面也发生了相应改变.不同微观形貌的晶体其Co含量有所差异,较大的晶体掺杂Co元素相对含量大于较小的晶体,+c(1011)显露面Co元素的含量比+c(1010)面高,锥柱状晶体其区别尤为明显.大的晶体内部存在着少量的氧化钴团簇,晶体表面与晶体内部Co元素分布相对均匀.由于Co2+具有磁性,因此,氧化钴团簇的存在将对氧化锌稀磁半导体晶体的磁性产生一定的影响.     

TM掺杂的Ⅲ-Ⅴ族稀磁半导体电磁性质的第一原理计算

使用基于自旋局域密度泛函理论的第一性原理方法对3d过渡金属(TM=V，Cr，Mn，Fe，Co和Ni)掺杂的Ⅲ-Ⅴ族半导体(GaAs和GaP)的电磁性质进行了计算.结果发现：用V，Cr和Mn掺杂时体系将出现铁磁状态，而Fe掺杂时将出现反铁磁状态，Co和Ni掺杂时，其磁性则不稳定.其中，Cr掺杂的GaAs和GaP将可能是具有较高居里温度的稀磁半导体(DMS).在这些DMS系统中，V离子的磁矩大于理论期待值，Fe，Co和Ni离子的磁矩小于理论期待值，Cr和Mn离子的磁矩与期待值的差距取决于晶体的对称性以及磁性离子的能带分布.此外，使用Si和Mn共同对Ⅲ-Ⅴ族半导体进行掺杂，将有利于DMS表现为铁磁状态，并可以使体系的T_C进一步提高. 关键词： 稀磁半导体 过渡金属 掺杂 共掺杂     

X射线吸收谱对Ga0.946Mn0.054As薄膜中缺陷的研究

采用低温分子束外延法(LT-MBE)制备出Ga_0.946Mn_0.054As稀磁半导体(DMS)薄膜.通过X射线吸收谱(XAS)研究影响Ga_0.946Mn_0.054As薄膜性质的主要缺陷Mn间隙原子(Mn_I)和As反位原子(As_Ga).实验结果表明,在较低生长温度(T_S=200℃)下Ga_0.946Mn_{0.054 关键词： 0.946}Mn_0.054As稀磁半导体')" href="#">Ga_0.946Mn_0.054As稀磁半导体 X射线吸收谱 As反位缺陷 Mn间隙原子     

Mg和Ni共掺杂的ZnO稀释磁性半导体在磁性和光催化的应用

随着引入磁性元素，氧化锌最近被广泛用作磁性半导体. 本文报告了Mg和Ni共掺杂的ZnO的纯相合成，并研究其结构、光学、磁性和光催化特性. X射线衍射分析显示其六方纤锌矿型结构具有P63mc构型且不含任何杂质. 紫外可见分光光度法表明，随着ZnO中掺杂的Mg和Ni含量增加，带隙发生变化. 磁性测量实验显示Ni和Mg共掺杂的ZnO磁性加强，带隙的稳定进一步证实其结构的稳定性，实现了其在现代自旋电子设备的磁调谐性能. 对甲基绿的光催化降解实验结果表明，Mg和Ni共掺杂ZnO的活性增强.     

稀释磁性半导体Sn1-xMnxO2的室温铁磁性

采用固相反应法，制备了不同成分的稀释磁性半导体Sn_1-xMn_xO ₂(x=002，004，006)．利用x射线衍射和傅里叶变换红外光谱法证明 了锰均匀地掺杂到二氧化锡中．在室温下研究了掺锰二氧化锡基稀释半导体的磁性，发现它具有明显的铁磁性 ，同时对磁性的强弱与锰的含量和烧结温度的关系作了研究． 关键词： 稀释磁性半导体 掺杂 烧结 铁磁性 1-xMn_x O₂')" href="#">Sn_1-xMn_x O₂     

磁控溅射法制备钴掺杂氧化锌薄膜室温磁学性质

钴掺杂氧化锌是室温稀磁半导体的重要候选材料,其磁学特性和钴掺杂浓度、显微结构及光学性质密切相关。磁控溅射具有成本低、易于大面积沉积高质量薄膜等特点,是广受关注的稀磁半导体薄膜制备方法。利用磁控溅射方法制备了不同浓度的钴掺杂氧化锌薄膜,并对其显微结构、光学性质和磁学特性进行了系统分析。结果表明:当掺杂原子分数在8%以内时,钴掺杂氧化锌薄膜保持单一的铅锌矿晶体结构,钴元素完全溶解在氧化锌晶格之中;薄膜在可见光区域有很高的透射率,但在567, 615和659 nm处有明显吸收峰,这些吸收峰源于Co2+处于O2-形成的四面体晶体场中的特征d-d跃迁。磁学特性测试结果表明钴掺杂氧化锌薄膜具有室温铁磁性,且钴的掺杂浓度对薄膜的磁学特性有重要影响。结合薄膜结构、光学和电学性质分析,实验中观察到的室温铁磁性应源于钴掺杂氧化锌薄膜的本征属性,其铁磁耦合机理可由束缚磁极化子模型进行解释。     

磁控溅射法制备钴掺杂氧化锌薄膜室温磁学性质（英文）

钴掺杂氧化锌是室温稀磁半导体的重要候选材料,其磁学特性和钴掺杂浓度、显微结构及光学性质密切相关。磁控溅射具有成本低、易于大面积沉积高质量薄膜等特点,是广受关注的稀磁半导体薄膜制备方法。利用磁控溅射方法制备了不同浓度的钴掺杂氧化锌薄膜,并对其显微结构、光学性质和磁学特性进行了系统分析。结果表明:当掺杂原子分数在8%以内时,钴掺杂氧化锌薄膜保持单一的铅锌矿晶体结构,钴元素完全溶解在氧化锌晶格之中;薄膜在可见光区域有很高的透射率,但在567,615和659nm处有明显吸收峰,这些吸收峰源于Co2+处于O2-形成的四面体晶体场中的特征d-d跃迁。磁学特性测试结果表明钴掺杂氧化锌薄膜具有室温铁磁性,且钴的掺杂浓度对薄膜的磁学特性有重要影响。结合薄膜结构、光学和电学性质分析,实验中观察到的室温铁磁性应源于钴掺杂氧化锌薄膜的本征属性,其铁磁耦合机理可由束缚磁极化子模型进行解释。     

On the paramagnetic behavior of heavily doped Zn1−xMnxO films fabricated by Pechini’s method

Heavily doped Zn_1−xMn_xO (x = 0.3) films were prepared by polymeric precursor method onto glass substrates and their structural, morphological, optical and magnetic properties carefully studied. Undoped ZnO films were also prepared for the purpose of comparison. The polymeric precursor method consists in preparing a coating solution from the Pechini process followed by a three-step thermal treatment of the as deposited films at temperatures up to 550 °C for 30 min. X-ray diffraction (XRD) analysis reveals the typical hexagonal wurtzite structure of the undoped ZnO film. The addition of Mn ions leads to a dramatic reduction of the crystalline quality of film although no evidence of affectation by secondary phases is found. The affectation of the ZnO structure may be due to the formation of Mn clusters and generation of defects such as vacancies and interstitials. Here, the solubility limit of the Mn ions in ZnO should play an important role and it is discussed in the framework of ionic radius and valence states. The scanning electron microscopy (SEM) analysis shows that the surface of the doped sample was affected by the presence of cracks due, probably, to the expansion of the lattice constant of Zn_0.7Mn_0.3O caused by the Mn incorporation in the ZnO lattice. The existence of cluster-type structures on the surface is corroborated by atomic force microscopy (AFM). The EDX analysis, carried out on some areas in the film, yielded Mn/Zn ratios of about 0.3, which points out to an effective Mn incorporation in the film. On the other hand, the absorption edge of the doped films is red shifted to 2.9 eV (3.24 eV for undoped ZnO film) and the absorption edge is less sharp due, probably, to amorphous states appearing in the band gap. No evidence of dilute magnetic semiconductor mean-field ferromagnetic behavior is observed. The temperature dependence of the magnetization follows a Curie law suggesting pure paramagnetic behavior. The very small s-shape behavior of M versus H (without hysteresis) observed at room temperature on selected areas would stem from Mn clusters which are easily formed in transition metal doped ZnO.     

Preparation and Characterization of Mn Doped ZnO Nanorods

Physics of the Solid State - Mn doped ZnO nanorods were prepared by chemical precipitation method. The micro-structural and structural properties of the nanorods were calculated from the X-ray...     

Microstructural and magnetic properties of Ax:Zn1-xO (A=Mn,Gd and Mn/Gd) nanocrystals

We report the microstructural and magnetic properties of transition (3d) and rare earth (4f) metal substituted into the A_x:Zn_1?xO (A=Mn, Gd and Mn/Gd) nanocrystal samples synthesized by solgel method. The structural properties and morphology of all samples have been analysed using X-ray diffraction (XRD) method and scanning electron microscopy. The impurity phase in the XRD patterns for all samples is not seen, except (Mn/Gd):ZnO sample where a very weak secondary phase of Gd₂O₃ is observed. Due to the large mismatch of the ionic radii between Mn²⁺ and Gd³⁺ ions, the strain inside the matrix increases, unlike the crystallite size decreases with the substitution of Mn and Gd into ZnO system. A couple of additional vibration modes due to the dopant have been observed in Raman spectrum. The magnetic properties have been studied by vibrating sample magnetometer. The magnetic hysteresis shows that Mn:ZnO and Gd:ZnO have soft ferromagnetic (FM) behaviour, whereas (Mn/Gd):ZnO has strong FM behaviour at room temperature (RT). The enhancement of ferromagnetism (FM) in (Mn/Gd):ZnO sample might be related to short-range FM coupling between Mn²⁺ and Gd³⁺ ions via defects potential and/or strain-induced FM coupling due to the expansion lattice by doping. The experimental results indicate that RTFM can be achieved by co-substitution of 3d and 4f metals in ZnO which can be used in spintronics applications.     

Co和Mn共掺杂ZnO铁磁性的第一性原理

基于密度泛函理论(DFT)的总体能量平面波超软赝势方法,结合广义梯度近似(GGA),对Co单独掺杂ZnO和(Co,Mn)共掺杂ZnO的32原子超原胞体系进行了几何结构优化,计算了纤锌矿结构ZnO、Co-ZnO及(Co,Mn)共掺杂ZnO的能带结构、电子态密度,并对此进行了详细的分析。计算结果表明,ZnO中单独掺杂Co元素显示出铁磁性行为,Mn的引入减弱了Co-ZnO的铁磁性。     

Mn掺杂ZnO纳米线磁性质的第一性原理研究

本文采用第一性原理方法系统研究了Mn原子单掺杂和双掺杂ZnO纳米线的稳定性和磁性质.所有掺杂纳米线的束缚能都为负值,表明掺杂增强了纳米线的稳定性.表面掺杂纳米线显示了直接带隙半导体特性,而中间掺杂纳米线显示了间接带隙半导体特性.纳米线的总磁矩主要来源于Mn原子3d轨道的贡献.由于杂化,相邻的O原子和Zn原子也产生了少量自旋.在超原胞内,Mn原子和O原子磁矩平行排列,表明它们之间是铁磁耦合.     

退火氛围对掺杂ZnO薄膜磁性的影响

采用直流磁控反应共溅法制备了非磁性元素Al和磁性元素Co掺杂的ZnO薄膜, 样品原位真空退火后再空气退火处理. 利用X射线衍射仪(XRD) 和物理性能测量仪(PPMS) 对薄膜的结构和磁性进行了表征. XRD和PPMS结果表明, 不同的退火氛围对掺杂薄膜的结构和磁性有着很大的影响. 真空退火的Al掺杂ZnO薄膜没有观察到铁磁性, 而空气退火的样品却显示出明显的室温铁磁性, 铁磁性的来源与空气退火后导致Al和ZnO基体间电荷转移增强有关. 而对于Co掺杂ZnO薄膜, 真空退火后再空气退火, 室温铁磁性明显减弱. 其磁性变化与Co离子和ZnO基体间电荷转移导致磁性增强和间隙Co原子被氧化导致磁性减弱有关.     

The electronic and magnetic properties of （Mn,C）-codoped ZnO diluted magnetic semiconductor

The electronic and magnetic properties of (Mn,C)-codoped ZnO are studied in the Perdew-Burke-Ernzerhof form of generalized gradient approximation of the density functional theory. By investigating five geometrical configurations, we find that Mn doped ZnO exhibits anti-ferromagnetic or spin-glass behaviour, and there are no carriers to mediate the long range ferromagnetic (FM) interaction without acceptor co-doping. We observe that the FM interaction for (Mn,C)-codoped ZnO is due to the hybridization between C 2p and Mn 3d states, which is strong enough to lead to hole-mediated ferromagnetism at room temperature. Meanwhile, we demonstrate that ZnO co-doped with Mn and C has a stable FM ground state and show that the (Mn,C)-codoped ZnO is FM semiconductor with super-high Curie temperature (T C = 5475 K). These results are conducive to the design of dilute magnetic semiconductors with codopants for spintronics applications.     

Properties of Mn-doped ZnO nanopowder

The structural and magnetic properties of Mn-doped ZnO nanopowder are investigated and compared to undoped ZnO crystals. Mn incorporation leads to an increase in the lattice constants as revealed by X-ray diffraction measurements. An inhomogeneous distribution of the Mn atoms within the nanopowder was detected by energy-dispersive X-ray and electron-energy-loss spectroscopy measurements. Magnetic features are investigated by means of SQUID magnetometry on ensembles of powder particles as well as by magnetic force microscopy to study the behavior of single grains. PACS 75.50.Pp; 75.75.+a; 78.55.Et     

Quenching of surface traps in Mn doped ZnO thin films for enhanced optical transparency

The structural and photoluminescence analyses were performed on un-doped and Mn doped ZnO thin films grown on Si (1 0 0) substrate by pulsed laser deposition (PLD) and annealed at different post-deposition temperatures (500-800 °C). X-ray diffraction (XRD), employed to study the structural properties, showed an improved crystallinity at elevated temperatures with a consistent decrease in the lattice parameter ‘c’. The peak broadening in XRD spectra and the presence of Mn 2p3/2 peak at ∼640 eV in X-ray Photoelectron Spectroscopic (XPS) spectra of the doped thin films confirmed the successful incorporation of Mn in ZnO host matrix. Extended near band edge emission (NBE) spectra indicated the reduction in the concentration of the intrinsic surface traps in comparison to the doped ones resulting in improved optical transparency. Reduced deep level emission (DLE) spectra in doped thin films with declined PL ratio validated the quenching of the intrinsic surface traps thereby improving the optical transparency and the band gap, essential for optoelectronic and spintronic applications. Furthermore, the formation and uniform distribution of nano-sized grains with improved surface features of Mn-doped ZnO thin films were observed in Field Emission Scanning Electron Microscopy (FESEM) images.     

Synthesis of Mn doped ZnO nanoparticles with biocompatible capping

Free standing nanoparticles of ZnO doped with transition metal ion Mn have been prepared by solid state reaction method at 500 °C. X-ray diffraction (XRD) analysis confirmed high quality monophasic wurtzite hexagonal structure with particle size of 50 nm and no signature of dopant as separate phase. Incorporation of Mn has been confirmed with EDS. Bio-inorganic interface was created by capping the nanoparticles with heteromultifunctional organic stabilizer mercaptosuccinic acid (MSA). The surface morphological studies by scanning electron microscopy (SEM) showed formation of spherical particles and the nanoballs grow in size uniformly with MSA capping. MSA capping has been confirmed with thermo gravimetric analysis (TGA) and FTIR. Photoluminescence (PL) studies show that the ZnO:Mn²⁺ particles are excitable by blue light and emits in orange and red. Occurrence of room temperature ferromagnetism in Mn doped ZnO makes such biocompatible luminescent magnetic nanoparticles very promising material.