光沉积Ru和RuO2的锐钛矿TiO2纳米片的光解水产氧

采用水热法以HF作为结构调控剂合成了主要暴露（001）面的锐钛矿TiO₂纳米片,通过光沉积方法分别合成了负载Ru和RuO₂物种的光催化剂。利用X射线衍射、透射电镜和氢气程序升温还原等分析表征了催化剂的结构性质。通过光解水产氧反应来研究催化剂的催化性能,详细考察了Ru含量、负载方式以及氧化和还原处理等因素的影响,光解水产氧速率的差异证明了Ru物种在不同晶面的电荷-空穴分离效应。与负载单一助催化剂的Ru/TiO₂和RuO₂/TiO₂样品相比,活性最优的0.5%Ru-1.0%RuO₂/TiO₂样品由于负载了双助催化剂,其催化活性得到更大的提高,证实了在锐钛矿TiO₂上的晶面电荷-空穴分离效应.     

由纳米管和纳米颗粒构成的TiO2膜的制备与机理研究

采用聚苯乙烯小球修饰Ti片表面,并进行阳极氧化,制备出一种由纳米颗粒和纳米管构成的TiO₂膜．通过数值模拟,分析了氧化表面附近的局部电场分布对TiO₂膜形貌的影响．结果表明,覆盖物增强了局部电场,从而加快了O^2-与Ti的反应速率,有利于TiO₂的生长;与此同时,[TiF₆]^6-的扩散受到阻碍,使得TiO₂的溶解速率减慢．可见,覆盖物打破了TiO₂纳米管形成的平衡条件,导致纳米颗粒的生成．此外,通过X射线衍射和Raman光谱的测试分析发现,所制备的TiO₂为锐钛矿结构.     

合成氨钌催化剂的晶体和形貌敏感性

哈伯-博施法合成氨反应是高温高压的耗能过程,因此降低该过程的能量消耗及开发温和条件下合成氨反应催化剂具有重要意义. 金属钌是合成氨反应中最有前途的催化剂之一,一直备受广泛关注. 确定金属钌催化剂的结构敏感性并提高其比质量活性是多相催化中亟待解决的重要问题. 氮气(N₂)活化是合成氨反应中的关键步骤. 本文通过第一性原理理论计算和微观动力学模拟方法系统研究了具有六方密排和面心立方晶体结构的钌催化剂上N₂活化过程和N₂解离反应速率. 理论计算研究表明,在六方密排Ru形貌中,{2130}晶面具有最高的N₂解离活性,其次是{0001}台阶面,它们比六方密排Ru其他表面上N₂解离反应速率高3个数量级以上;在面心立方Ru形貌中,{211}和{311}表面上N₂解离活性最高. 这些结果都表明台阶面/台阶位对氮气活化至关重要. 虽然六方密排Ru {2130}晶面具有最低的N₂解离能垒,然而由于面心立方Ru上可以暴露更高密度的活性位点,使得面心立方Ru比六方密排Ru具有更高的N₂转化速率. 本研究深入理解了N₂解离过程中,金属Ru 催化剂形貌和晶相结构敏感性,这为设计和优化高活性的合成氨Ru催化剂提供了理论基础.     

硼(氮、氟)掺杂对TiO2纳米颗粒光学性能的影响

利用X射线衍射谱、拉曼光谱和紫外-可见光吸收光谱研究了硼(氮、氟)掺杂对TiO₂纳米颗粒光学性能的影响.X射线衍射谱和拉曼光谱结果表明,掺硼(氮、氟)对TiO₂纳米颗粒的锐钛矿相晶体结构无明显影响,而其锐钛矿晶格出现畸变(c/a值增大),这被归因于掺杂原子对TiO₂纳米颗粒表面氧原子缺位沿晶格c轴方向的占据.另外,掺硼(氮、氟)TiO₂纳米颗粒吸收带红移与TiO相似文献   

亚纳米厚的氧化铝包裹层可以显著提高负载型金纳米颗粒催化剂的热稳定性

负载型金纳米颗粒催化剂在许多催化反应中展现出非常好的催化活性,但是金纳米颗粒在高温等反应条件下容易烧结团聚,极大地限制了金催化剂的应用。利用原子层沉积技术在Au/TiO₂催化剂表面分别精确沉积了一层超薄的二氧化钛和氧化铝包裹层,并对比研究了包裹层对金纳米颗粒的热稳定性影响。原位红外漫反射CO吸附和x-射线光电子能谱数据证实了氧化物包裹层的存在。发现亚纳米厚的氧化铝包裹层能够在600 C完全避免金纳米颗粒的团聚;相反,二氧化钛包裹层对金纳米颗粒稳定性的提高没有明显效果。通过CO氧化探针反应的活性测试,发现随着煅烧温度的升高氧化铝包裹的Au/TiO₂ 催化剂的活性逐渐提高,表明高温处理可以促进被包裹金原子的暴露并表现出催化活性。提供了提高金纳米颗粒稳定性的有效方法,为拓展金催化剂在条件苛刻的反应中的应用奠定了技术基础.     

二氧化钛纳米晶/石墨烯复合物的制备及其光催化性能 (cited: 1)

以氧化石墨和TiO₂溶胶为前驱物,结合絮凝与水热技术制备了TiO₂纳米晶/石墨烯复合物,表征了产物的结构、形貌、孔隙率、光谱吸收性质. 结果表明：TiO₂纳米晶的存在一定程度上阻止了石墨烯片层的重组,TiO₂纳米晶/石墨烯复合物较单纯TiO₂材料具有更强的吸光性能、对亚甲基蓝分子更强的吸附性能以及更高的电荷分离效率. 在紫外光和太阳光下,TiO₂纳米晶/石墨烯复合物对亚甲基蓝的光催化降解效率均高于P25和纯TiO₂.     

Enhanced Photoelectrochemical Property of Zn Loaded TiO2 Nanotube Arrays Electrode

采用计时电流法制备了负载Zn纳米粒子的TiO₂纳米管阵列电极．通过阳极氧化法制备TiO₂纳米管阵列电极,然后通过控制计时电流沉积时间来控制负载在TiO₂纳米管上Zn纳米颗粒的沉积量和 沉积尺寸．SEM和XRD分析结果显示,沉积时间为3～5 s时,负载在TiO₂纳米管上的Zn粒子的直径为15～25 nm．UV漫反射光谱发现负载Zn的TiO₂纳米管阵列电极比没有负载的样品吸收487～780 nm的光更强;在高压汞灯照射下,前者比后者的光电流响应提高了50%．     

基于薄膜电极溶胶修饰的染料敏化太阳电池光电特性研究

染料敏化太阳电池(DSC)中的纳米薄膜电极 是决定太阳电池光电转换性能的重要组成部分. 为改善薄膜电极特性, 采用了不同浓度的TiO₂溶胶对DSC光阳极导电玻 璃和纳米TiO₂多孔薄膜进行不同方式的界面处理. 利用X射线衍射方法对制备得到的多孔薄膜以及溶胶经高温处理 后致密层中纳米TiO₂颗粒的尺寸及晶型进行了测试. 采用高分辨透射电子显微镜和场发射扫描电子 显微镜观察了纳米颗粒及薄膜微结构形貌. 采用强度调制光电流谱/光电压谱分析了TiO₂溶 胶的不同处理方式对电子传输和复合的影响. 在100 mW· cm^-2光强以及暗环境下分别测试了DSC的伏安输出性能以及暗电流. 结果表明, 不同浓度和处理方式均能较好地抑制暗电流. 溶胶处理后光生电子寿命τ_n延长, 电子传输平均时间τ_d相应缩短. 采用浓度为0.10 mol·L^-1的 溶胶对导电玻璃和多孔膜同时处理, DSC的宏观输出特性最佳, 短路电流密度J_sc提高了10.9%, 光电转换效率η提高了11.9%.     

Photocatalytic Activity of N-doped TiO2 Photocatalysts Prepared from the Molecular Precursor (NH4)2TiO(C2O4)2

用不同温度控制分解草酸氧钛铵制备N掺杂TiO₂光催化剂．利用XRD、IR、热分析、N₂吸-脱附等温线、XPS、紫外可见漫反射光谱和SEM表征了N-TiO₂光催化剂的结构．400～600 oC焙烧的N-TiO₂光催化剂为纯锐钛矿相,而700 oC焙烧的N-TiO₂光催化剂为锐钛矿和金红石混合相．N掺杂在TiO₂的间隙位使锐钛矿相TiO₂带隙变窄．在光降解甲基橙的反应中,600和400 oC焙烧的N-TiO₂催化剂分别在紫外光和全波长光照射下有最好活性;700 oC焙烧的N-TiO₂催化剂无论在紫外光和全波长光下都表现出最好的比活性,即最高的光量子效率,这可以归因于700 oC焙烧的N-TiO₂光催化剂良好的结晶程度和锐钛矿-金红石异相结的存在．     

溶剂热再结晶合成由纳米颗粒自组装成的一维CdS纳米棒

采用两种不同的溶剂热路径合成出了不同形貌和尺寸的CdS纳米晶, 一种是以无水乙二胺(en) 为溶剂, CdCl₂·2.5H₂O和硫脲(H₂NCSH₂N) 为镉源和硫源, 在不同反应温度(160 ℃-220 ℃ 下制备出了CdS纳米晶, 讨论温度对CdS纳米晶生长的影响; 另一种是以en为溶剂, 将在160 ℃下合成的产物在200 ℃下原位再结晶生长2-8 h, 分析原位生长时间对CdS纳米晶生长的影响. 通过X射线衍射(XRD)、 扫描电子电镜(SEM) 和透射电子电镜(TEM) 等表征产物的物相、 形貌和微结构, 分析可知: 两种路线合成的产物均为六方相CdS; 当温度为160 ℃时, 产物形貌为纳米颗粒状, 当温度高于160 ℃时, 产物为CdS纳米棒状; 同时, 在200 ℃下原位再结晶生长不同时间后发现产物形貌由纳米颗粒转变为纳米棒, 通过场发射扫描电镜(HRTEM) 分析可知: 纳米棒是由零维纳米颗粒自组装而成. 最后, 讨论了影响产物CdS纳米晶形貌转变的因素和纳米棒的生长机理.     

Au/TiO2/Ru(0 0 0 1) model catalysts and their interaction with CO

Au/TiO₂/Ru(0 0 0 1) model catalysts and their interaction with CO were investigated by scanning tunneling microscopy and different surface spectroscopies. Thin titanium oxide films were prepared by Ti deposition on Ru(0 0 0 1) in an O₂ atmosphere and subsequent annealing in O₂. By optimizing the conditions for deposition and post-treatment, smooth films were obtained either as fully oxidized TiO₂ or as partly reduced TiO_x, depending on the preparation conditions. CO adsorbed molecularly on both oxidized and reduced TiO₂, with slightly stronger bonding on the reduced films. Model catalyst surfaces were prepared by depositing submonolayer quantities of Au on the films and characterized by X-ray photoelectron spectroscopy and scanning tunneling microscopy. From X-ray photoelectron spectroscopy, a weak interaction between the Au and the TiO₂ substrate was found. At 100 K CO adsorption occurred on both the TiO₂ film and on the Au nanoparticles. CO desorbed from the Au particles with activation energies between 53 and 65 kJ/mol, depending on the Au coverage. If the Au deposit was annealed to 770 K prior to CO exposure, the CO adsorption energy decreased significantly. STM measurements revealed that the Au particles grow upon annealing, but are not encapsulated by TiO_x suboxides. The higher CO adsorption energy observed for smaller Au coverages and before annealing is attributed to a significantly stronger interaction of CO with mono- and bilayer Au islands, while for higher particles, the adsorption energy becomes more bulk-like. The implications of these effects on the known particle size effects in CO oxidation over supported Au/TiO₂ catalysts are discussed.     

Synthesis, characterization and effect of calcination temperature on phase transformation and photocatalytic activity of Cu,S-codoped TiO2 nanoparticles

A novel copper and sulfur codoped TiO₂ photocatalyst was synthesized by modified sol-gel method using titanium(IV) isopropoxide, CuCl₂·2H₂O and thiourea as precursors. The samples were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), scanning electron microscopy equipped with energy dispersive X-ray micro-analysis (SEM-EDX), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) analysis. The XRD results showed undoped and Cu,S-codoped TiO₂ nanoparticles only include anatase phase. Effect of calcination temperature showed rutile phase appears in 650 and 700 °C for undoped and 0.1% Cu,S-codoped TiO₂, respectively. The SEM analysis revealed the doping of Cu and S does not leave any change in morphology of the catalyst surface. The increase of copper doping enhanced “red-shift” in the UV-vis absorption spectra. The TEM images confirmed the dopants suppressed the growth of TiO₂ grains. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. The results showed photocatalytic activity of the catalysts with 0.05% Cu,0.05% S and 0.1% Cu,0.05% S were higher than that of other catalysts under ultraviolet (UV) and visible irradiation, respectively. Because of synergetic effect of S and Cu, the Cu,S-codoped TiO₂ catalyst has higher activity than undoped and Cu or S doped TiO₂ catalysts.     

Oriented single crystalline TiO2 nano-pillar arrays directly grown on titanium substrate in tetramethylammonium hydroxide solution

Oriented single crystalline titanium dioxide (TiO₂) nano-pillar arrays were directly synthesized on the Ti plate in tetramethylammonium hydroxide (TMAOH) solution by one-pot hydrothermal method. The samples were characterized respectively by means of field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), and X-ray diffraction (XRD). Results showed that the TiO₂ nano-pillar with a tetrahydral bipyramidal tip grew vertically on the titanium substrate. HRTEM and Raman results confirmed that the TiO₂ nano-pillar arrays were single crystalline anatase. The controls of morphology, size, and orientation of the nano-pillar could be achieved by varying the solution concentration and hydrothermal temperature. Furthermore, the special morphology of the TiO₂ nano-pillar arrays was caused by the selectively absorption of the tetramethylammonium (TMA) through hydrogen bonds on the lattice planes parallel to (0 0 1) of anatase TiO₂. Less grain boundaries and direct electrical pathway for electron transferring were crucial for the superior photoelectrochemical properties of the single anatase TiO₂ nano-pillar arrays. This approach provides a facile in situ method to synthesize TiO₂ nano-pillar arrays with a special morphology on titanium substrate.     

Electrochemical deposition of silver nanoparticles on TiO2/FTO thin films

Silver nanoparticles were deposited on titanium oxide^IV (TiO₂) thin films supported on FTO (fluorine-doped tin oxide^IV) glass using a double pulse electrochemical deposition method. A systematic study of particle nucleation and growth is presented as a function of applied potential and time. Samples were analyzed by grazing-angle X-ray diffraction (GIXRD) technique and morphology was observed using Scanning Electron Microscopy and Energy Dispersive Spectroscopy device (SEM-EDS). Our results confirm the possibility of controlled electrochemical homogeneous deposition of metallic silver particles over TiO₂ surface, which exhibit a potential application in catalytic processes.     

Preparation and performance of photocatalytic TiO2 immobilized on palladium-doped carbon fibers

Pd-modified carbon fibers (CFs) are obtained by a facile oxidation-reduction method and then dip-coated in a sol-gel of titanium dioxide (TiO₂) to form supported TiO₂/Pd-CF photocatalysts. The morphology of the Pd-modified CFs and the amount Pd deposited are characterized by field emission scanning electron microscopy and atomic absorption spectrometry, respectively. X-ray diffraction is used to investigate the crystal structures of the TiO₂ photocatalyst. Acid orange II is used as a model contaminant to evaluate the photocatalytic properties of the photocatalyst under UV irradiation. TiO₂/Pd-CF exhibits higher catalytic activity than TiO₂/CF towards the degradation of acid orange II. Optimum photocatalytic performance and support properties are achieved when the Pd particle loading is about 10.8 mg/g.     

A versatile sonication-assisted deposition–reduction method for preparing supported metal catalysts for catalytic applications

This work aims to develop a rapid and efficient strategy for preparing supported metal catalysts for catalytic applications. The sonication-assisted reduction–precipitation method was employed to prepare the heterogeneous mono- and bi-metallic catalysts for photocatalytic degradation of methyl orange (MO) and preferential oxidation (PROX) of CO in H₂-rich gas. In general, there are three advantages for the sonication-assisted method as compared with the conventional methods, including high dispersion of metal nanoparticles on the catalyst support, the much higher deposition efficiency (DE) than those of the deposition–precipitation (DP) and co-precipitation (CP) methods, and the very fast preparation, which only lasts 10–20 s for the deposition. In the AuPd/TiO₂ catalysts series, the AuPd(3:1)/TiO₂ catalyst is the most active for MO photocatalytic degradation; while for PROX reaction, Ru/TiO₂, Au–Cu/SBA-15 and Pt/γ-Al₂O₃ catalysts are very active, and the last one showed high stability in the lifetime test. The structural characterization revealed that in the AuPd(3:1)/TiO₂ catalyst, Au–Pd alloy particles were formed and a high percentage of Au atoms was located at the surface. Therefore, this sonication-assisted method is efficient and rapid in the preparation of supported metal catalysts with obvious structural characteristics for various catalytic applications.     

Effect of crystalline structure of TiO2 substrates on initial growth of atomic layer deposited Ru thin films

Ru thin films were grown on polymorphic TiO₂ thin film substrates at 230 and 250 °C by atomic layer deposition using 2,4-(dimethylpentadienyl)(ethylcyclopentadienyl)Ru and an O₂ gas. While the Ru films grown on amorphous and rutile TiO₂ substrates showed a relatively long incubation cycle number of approximately 350 and 100 at 230 and 250 °C, respectively, the Ru films grown on anatase TiO₂ substrates exhibited a significantly shorter incubation delay which was attributed to the catalytic activity of anatase TiO₂. This difference in the incubation cycle affected the surface morphology of the Ru films on different TiO₂ substrates.     

Effect of nano-titanium hydride on formation of multi-nanoporous TiO2 film on Ti

The effect of titanium hydride on the formation of nanoporous TiO₂ on Ti during anodization has been investigated by X-ray photoelectron spectroscopy, grazing incident X-ray diffraction, transmission electron microscopy and scanning electron microscopy. Titanium hydride (TiH₂) was formed after cathodization, profoundly impacting the formation of nanoporous TiO₂ on Ti by anodization. Oxide layer and nanocrystal structure were observed after anodization with cathodic pretreatments. A multi-nanoporous TiO₂ layer was formed on the titanium. The titanium hydride is a nanostructure. The nanostructure is directly changed to nanoporous TiO₂ by a dissolution reaction during anodization. The nanoporous layer is difficult to form without cathodization. The nanostructural TiH₂ is important in forming a nanoporous TiO₂ layer. Anodization treatment with cathodic pretreatment not only yields a titanium surface with a multi-nanostructure, but also transforms the titanium surface into a nanostructured titanium oxide surface.