首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到15条相似文献,搜索用时 141 毫秒
1.
研究了生物质气化合成气在Fe1.5Cu1Zn1Al1K0.117催化剂上高效转化为清洁生物燃料的合成过程. 利用生物质气化合成气合成的生物燃料最大产率为1.59 kg/(kgcatal·h), 其中醇占0.57 kg/(kgcatal·h), 液体烃占1.02 kg/(kgcatal·h). 在生物燃料中, 醇类产物主要为C2+醇(主要为C2-C6高碳醇), 其含量占总醇的7  相似文献   

2.
研究了一种以生物质裂解油为原料制备氢气和生物燃料的催化转化过程。该过程包括生物油催化裂解制备氢气和生物合成气,合成气的调变,烯烃聚合和费脱合成耦合制备生物燃料。在优化反应条件下,氢气产率达到120.9 g H2/(kg bio-oil),烯烃聚合-费脱合成耦合反应形成的生物燃料产率达到526.1 g/(kg bio-syngas)。基于产物分析和催化剂特性表征,探讨了生物燃料合成过程中的反应路径和化学反应过程.  相似文献   

3.
一种组合了合成气在线调整和甲醇合成的双段床反应器,成功应用于由生物油重整得到的富CO2合成气的高效合成甲醇.在前段催化床反应器内,富含CO2的原始生物质合成气在CuZnAlZr催化剂的催化作用下可以有效地转化为含CO的合成气.经过450 oC的合成气在线调整之后,CO2/CO的比率由6.3大幅降至1.2.经过调整后的生物质基合成气在后段催化床反应器内由工业CuZnAl催化剂催化合成甲醇,当反应条件为260 oC 和5.5 MPa时得到每小时每kg催化剂的最大甲醇  相似文献   

4.
采用溶胶凝胶法与等体积浸渍相结合制备了一系列以粘土为载体的K-Co-Mo催化剂. 采用XRD、N2等温吸脱附、H26+的还原,但对Mo4+和Co2+的还原没有明显的影响. 催化剂经还原后,在其表面生成了一种更低价态的Moδ+(1<δ<4)物种,被认为是合成醇的活性中心. 与非负载催化剂相比,粘土担载的K-Co-Mo具有更高的合成醇性能. 负载型催化剂具有较高的活性物种分散度,并且其介孔结构在一定程度上延长了合成醇反应中间体的滞留时间,从而促进了低碳醇的生成. 经773 K还原的催化剂具有较高的活性,其原因可为催化剂表面具有较高含量的Moδ+物种.  相似文献   

5.
采用廉价的无机锆源(无水硝酸锆)通过一步法合成表面含强Lewis酸位的SO42-/Zr-SBA-15,该催化剂材料在废弃食用油和甲醇酯交换制生物柴油过程中表现出良好的催化活性和选择性. 实验考察了酯交换反应的最佳条件为:反应温度160 oC、反应时间12 h、催化剂Zr:Si为0.11、催化剂用量为10%、醇油比30:1. SO42-/Zr-SBA-15在最佳反应条件下可使甘油三酯的转化率达到92.3%,脂肪酸甲酯的产率为91.7%. SO42-/Zr-SBA-15具有高比表面积的介孔结构和表面酸性,且具有良好的反应稳定性和重复性,反应7次后的脂肪酸甲酯的产率仍稳定保持在74 ±1%.  相似文献   

6.
分别采用阳离子(十六烷基三甲基溴化铵,CTAB)、阴离子(十二烷基硫酸钠,SDS)、非离子(三嵌段共聚物,P123)三种不同类型的表面活性剂对CuCoMn基催化剂进行改性,利用N2吸脱附、XRD、XPS、IR手段表征了催化剂的微观结构.在生物质基合成气合成高醇中的应用研究结果表明,SDS修饰的CuCoMn催化剂表现出较高的CO转化率(29.7%),而CTAB修饰的CuCoMn催化剂具有优良的高醇选择性(41.2%).同时,三种表面活性剂修饰的催化剂均不同程度地提高了高醇产率及其在醇产  相似文献   

7.
本文制备了用于费托合成反应的钴改性Fe3O4-MnO2双功能催化剂,并探究了钴负载量对Fe-Co协同效应的影响以及Fe1CoxMn1催化剂的费托合成反应性能. 实验发现,在Fe3O4-Mn催化剂中加入Co可促进铁氧化物的还原、增加反应过程中铁位点的活性. 此外,Co的加入可增强Fe-Co金属间的电子转移,加强两者的协同作用,提高催化性能. Co负载较高的Fe1CoxMn1催化剂可进一步促进加氢反应能力,使产品分布向短链烃方向转移. 在280 °C、2.0 MPa和3000 h-1的最佳工况条件下,Fe1Co1Mn1催化剂的液体燃料收率最高.  相似文献   

8.
采用逐步湿浸渍的方法制备了一系列含有不同载体和碱促进剂的Ni基催化剂用于生物质基平台化合物山梨醇的氢解反应. 通过反应对载体和碱促进剂进行了筛选和组分含量的优化,碱性促进剂的引入不仅增强了催化剂的碱性,而且通过Ni2+和碱促进剂的强相互作用提高了Ni在催化剂上的分散性;10%Ni/10%La2O3/ZrO2表现出了非常高的氢解活性和较好的二元醇(乙二醇和1,2丙二醇)选择性,金属Ni和碱促进剂La2O3之间的协同作用机理对于山梨醇选择性氢解制备二元醇影响显著. 在优化的反应条件下,山梨醇达到100%的转化并且有超过48%的二元醇产率. 研究中对催化剂进行了XRD、BET、H2-TPR和CO2-TPD表征,用于分析催化剂结构性能. 通过对山梨醇氢解以及中间产物动力学曲线的研究,得出多元醇氢解活性与所含羟基数正相关,产物的最终分布是氢解动力学平衡的最终结果.  相似文献   

9.
选用四种不同的分子筛(SAPO-34, ZSM-5, Y, MCM-41)与CuCoMn(高醇合成组元)构成双功能催化剂,利用N2吸脱附、H2-TPR、XRD、NH3-TPD等表征了催化剂的结构性质. 研究了催化剂在生物质基合成气一段法制取液态烃燃料的应用. 相比于CuCoMn催化剂,加入分子筛的双功能催化剂均不同程度地提高了液体烃燃料的选择性及收率,且收率按顺序递减呈CCM-ZSM-5>CCM-SAPO-34>CCM-Y>CCM-MCM-41. 同时,共沉淀法制备的CuCoMn-ZSM-5 (20wt%, Si/Al=100) 具有最佳的CO转化率(76%)及液体产物收率(30%). 相比于CuCoMn氧化物,双功能催化剂的比表面及孔容均得到提高. CCM-ZSM-5具有适中的微孔尺寸和中等强度的酸性,增加CCM-ZSM-5中ZSM-5含量或降低ZSM-5中的Si/Al比,均有利于提高酸性位的数量,主要是较弱的酸性位. 而共沉淀法制备的CCM-ZSM-5具有更好的金属分散性及还原性能.  相似文献   

10.
低温陈化超声波共沉淀法制得SO42-/ZrO2-La2O3前驱体, 经H2SO4处理, 在不同温度下焙烧得到纳米晶催化剂SO42-/ZrO2-La2O3;用Hammett指示剂法测定其酸性. 用XRD、BET、TEM、IR和XPS对样品进行表征,其催化活性用醋酸和甘油的酯化反应进行了评价. 结果表明经超声波搅拌和低温(-15 ºC)陈化,650 ºC焙烧4 h得到的固体超强酸表现出较高催化活性.  相似文献   

11.
A series of carbon nanotubes-supported K-Co-Mo catalysts were prepared by a sol-gel method combined with incipient wetness impregnation.The catalyst structures were characterized by X-ray diffraction,N2 adsorption-desorption,transmission electron microscopy and H2-TPD,and its catalytic performance toward the synthesis of higher alcohols from syngas was investigated.The as-prepared catalyst particles had a low crystallization degree and high dispersion on the outer and inner surface of CNTs.The uniform mesoporous structure of CNTs increased the diffusion rate of reactants and products,thus promoting the reaction conversion.Furthermore,the incorporation of CNTs support led to a high capability of hydrogen absorption and spillover and promoted the formation of alkyl group,which served as the key intermediate for the alcohol formation and carbon chain growth.Benefiting from these characteristics,the CNTs supported Mo-based catalyst showed the excellent catalytic performance for the higher alcohols synthesis as compared to the unsupported catalyst and activated carbon supported catalyst.  相似文献   

12.
The research for “green” and economically feasible approaches such as (photo)catalysis especially for biomass valorization such as selective oxidation of biomass derived compounds like aromatic alcohols to corresponding aldehyde by avoiding the harsh reaction conditions and the addition of reagents concentrate the focus of attention the last years. Hence, design and development of novel photocatalyst for the partial selective oxidation is highly desirable. In this research work, ultrasonication of different frequencies (22, 40, 80 kHz) and different amplitudes was utilized as synthesis tool in order to obtain novel materials by precipitation method. The synthesized samples were characterized by using different techniques such as N2 sorption, TEM, XPS, XRD, thermal analysis, and diffuse reflectance spectroscopy. The synthesized sample by using low ultrasound frequency (22 kHz) and amplitude showed a mixed morphological and structural nature consisting of asymmetric 1-dimensional (nanorods-like), layered nano-structures and not well-defined areas, leading to elevate for metal oxide specific surface areas up to 155 m2/g. The observed 1-D nanostructures have diamentions in the range of 20–60 nm. This sample revealed the highest photo-oxidation efficiency for the selective conversion of two biomass-derived, and more specifically lignin-inspired model compounds, benzyl alcohol and cinnamyl alcohol to benzaldehyde and cinnamyl aldehyde, respectively, and hence the highest yield towards the desired aldehydes. The selective photo-oxidation activity was retained even after 5 photocatalytic cycles, while no leaching of Ti was recorded.  相似文献   

13.
A new technology, in which a renewable biomass is used to produce hydrogen fuel, is described. This hydrogen can be used as a feed for fuel cells to generate electricity or in other energy-producing processes. Degradation and gasification of cellulose-based biomass in compressed water was studied in the 100–400 °C temperature range. Phase behavior of the cellulose in subcritical water was studied in a diamond-anvil cell, coupled with optical microscopy, at heating rates of 1 and 5 °C/s. Homogeneous conditions of a single water-cellulose phase were established. Complete dissolution of the cellulose was achieved at 333 °C. The evolution mechanism based on a rapid hydrolysis of the cellulose to oligomers and glucose is suggested. Glucose was then used as a model compound to characterize the chemistry of biomass gasification. A 0.1-M glucose solution was fed into a continuous-flow reactor at a pressure of 100 bar using an HPLC pump. Catalytic effects of Pt/Al2O3 on the gasification temperature were determined. Gas product composition was analyzed using online GC-TCD. A mixture of H2, CO2, and CH4 gas was produced. Quantitative analysis of the total organic carbon in the liquid residue indicated 67% carbon gasification efficiency at 330 °C. Qualitative analyses of liquid residues showed that the main decomposition products in the liquid phase were alcohols and carboxylic acids. It was shown that the hydrogen fuel could be efficiently generated from biomass.  相似文献   

14.
Nanosized ZSM-5 type ferrisilicates were successfully prepared using hydrothermal process. Several parameters including gel initiative compositions (Na+ or K+ alkali system), SiO2/Fe2O3 molar ratios and hydrothermal temperature were systematically investigated. The samples were characterized by XRD, TEM, SEM-EDS, BET surface area and ICP techniques. It was found that surface areas and the total pore volume increase with increasing in the SiO2/Fe2O3 molar ratio at Na-FZ ferrisilicates. The catalytic performance of the synthesized catalysts was evaluated in ethylbenzene dehydrogenation to styrene in the presence of N2O or steam at temperatures ranging from 400 °C to 660 °C under atmospheric pressure. The effects of gel initiative compositions, SiO2/Fe2O3 molar ratio as well as the hydrothermal synthesis temperature on the catalytic performance of these catalysts have been addressed. It was shown that styrene yield significantly influenced by altering in the SiO2/Fe2O3 ratio but was not greatly influenced by changes in hydrothermal synthesis temperatures. The comparison between performance of potassium and sodium containing catalysts was shown that the one with potassium has higher yield and selectivity toward styrene production at an optimum temperature of 610 °C.  相似文献   

15.
A series of CuCe-modified TiO2-ZrO2 catalysts synthesized by stepwise impregnation method and ultrasonic-assisted impregnation method were investigated to research the removal of NO in the simulated flue gas. Results showed that the CuCe/TiO2-ZrO2 catalyst prepared by ultrasonic-assisted impregnation method exhibited the superior NO conversion, in which higher than 85% NO was degraded at the temperature range of 250–400 °C and the highest NO conversion of 94% at 350 °C. It proves that ultrasonic treatment can markedly improve the performance of catalysts. The effect of ultrasonic enhancement on CuCe/TiO2-ZrO2 was comprehensively studied through being characterized by physicochemical characterization. Results reveal that the ultrasonic cavitation effect improves the distribution of active species and the synergistic interaction between Cu with Ce components (Cu+ + Ce4+ ↔ Cu2+ + Ce3+) on the catalysts significantly, thus resulting in better dispersibility as well as a higher ratio of Cu2+ and Ce3+ of the catalysts. Moreover, it was found that the CuCe/TiO2-ZrO2 catalyst prepared by the ultrasonic-assisted impregnation method represented a higher degree of ultrafine metal particles and evenness. The above results were described with the generalized dimension and singularity spectra in multifractal analysis and validated by the comparative test. Therefore, it can be concluded that ultrasonic treatment facilitates the particle size and distribution of active sites on the catalysts.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号