新型单模光纤偏振器

本文介绍了新型D型微孔单模光纤偏振器的制作工艺及其性能参数。其工作波长为1.3μm,光纤偏振器的消光比优于40dB,插入损耗≤2.5dB.制作工艺较为简单,温度变化对器件的影响小,稳定性好,工作波长范围宽。     

基于多模光纤滤波器的可调谐掺铒光纤激光器

研究了一种新型、全光纤、宽带可调谐环形腔掺铒光纤激光器。该激光器利用由单模-多模-单模光纤组成的滤波器实现波长可调谐及激光器的全光纤结构。该滤波器将多模光纤缠绕在偏振控制器上,两端分别与一段单模光纤相连,通过调整偏振控制器的状态,实现了中心波长1542～1560nm的不同激光输出。单波长连续可调谐激光器的波长可调范围为18nm,边模抑制比大于40dB,3dB线宽为0.096nm;进一步调整偏振控制器的状态和抽运功率,实验同时得到了连续可调谐的双波长、三波长等多波长激光输出。对于可调谐的多波长激光器,通过调整偏振控制器的状态,可实现波长间隔及输出中心波长两者可调。     

光波导-光纤自动调芯系统研究

设计了两种适用于光波导高精度自动对接耦合的调芯方案,从原理上克服了常规调芯过程中微变信号精确测试的困难。完成了调芯系统的光机电一体化、控制程序和接口界面。单模光纤作为标准波导的端面耦合自动凋芯试验显示,平均耦合损耗分别为0．075 dB(1310nm波长)和0．062 dB(1550nm波长),相应的标准误差分别为0．0099 dB和0．0066 dB．调芯过程在2min内完成。单模光纤-单模波导-单模光纤的对接耦合实验结果表明,端面耦合损耗平均值分别为0．140 dB(1310nm波长)和0．109 dB(1550nm波长),标准误差分别为0．0082dB和0．0107dB,调芯时间累计不超过8min。     

新型全固态准晶体结构大模场光纤特性研究

大模场单模光纤在高功率激光器、高功率光传输和高灵敏度传感器等领域具有重要意义.设计了一种新型超低损耗大模场单模光纤,包层空气孔由掺氟硅玻璃棒代替,掺氟硅玻璃棒排列呈六重准晶体结构.基于有限元法对光纤的传输特性进行了数值模拟.研究了光纤结构参量变化对模式特性和有效模场面积的影响.结果表明:波长在1064 nm处,有效模场面积高达5197μm2,基模的限制性损耗低于10-5dB/km,解决了大模场与低损耗之间的冲突;在1064—2000 nm波段内,基模与二阶模的限制性损耗相差7个量级,实现单模传输;半径为10 cm时,弯曲损耗小于0.01 dB/m,具有良好的低弯曲损耗特性.此光纤能够提高光纤热损伤阈值,减少接续损耗,全固态结构有效避免了空气孔塌陷,简化制备工艺,对高功率激光传输、光纤激光器和光纤放大器的发展具有重要意义.     

基于光纤锥级联结构的湿度传感器

提出了一种基于普通单模光纤粗锥级联结构的马赫-曾德尔干涉湿度传感器.将两根单模光纤对芯熔融成一个粗锥,并依次级联,形成光纤锥-单模光纤-光纤锥-单模光纤-光纤锥结构.外界环境湿度、温度的改变使传感器的纤芯基模和包层模的光程差发生改变,引起传感器干涉光谱发生变化.通过监测干涉谱波长和能量的变化实现对外界物理量的测量.实验结果表明,当空气中湿度在35~95%RH范围内变化时,传感器的湿度灵敏度为-0.065dB/%RH,线性度为0.997;当温度在30~80℃范围内变化时传感器的温度灵敏度为69.4pm/℃,线性度为0.998.该传感器可以避免温湿度的交叉影响,实现单参量的同时在线区分测量.     

基于增强瑞利反馈的单模窄线宽随机激光器

仿真说明了单模光纤(SMF)中瑞利散射(RS)的机理, 指出纤芯掺杂的不均匀性以及拉丝过程引起的光纤几何尺寸的随机变化是光纤中RS产生的主要原因, 并以此为基础制作了损耗为0.54 dB/km的散射光纤. 在通信波段, 5 km该散射光纤的瑞利背向散射(RBS)强度高于相同长度的SMF-28近5 dB. 在基于RBS单模随机激光器的数值模拟中, 大量的具有随机幅度和相位的纵模在经历不平坦增益的多次放大之后, 只有在增益最大点附近的模式能够克服损耗成为输出模式. 实验中以掺铒光纤作为增益介质, 500 m散射光纤提供随机反馈, 窄带布拉格光纤光栅(FBG)作为波长选择器件, 得到线宽约3.5 kHz、对比度近50 dB的单模激光输出. 与采用相同长度SMF-28的随机激光器相比, 其阈值电流降低了80 mA, 相同抽运条件下的最大输出功率提高了3 dBm. 该单模窄线宽随机激光器的输出波长的调谐特性仅由FBG的中心波长决定.     

1150nm掺镱光纤激光器输出特性实验研究

以光纤光栅对为激光腔、双包层掺镱光纤为增益介质、976nm半导体激光器为泵浦源,研制全光纤化的1 150nm波段长波光纤激光振荡器.在室温下实现了最大平均输出功率为12.7 W的1 150nm波段单模光纤激光输出,激光振荡器的光光转换效率为42.33%.最大功率输出时,激光中心波长为1 150.48nm,光谱的3dB线宽为0.45nm,边模抑制比达38dB.该研究对研制1 150nm波段高功率光纤激光振荡器具有一定的参考价值.     

单模光纤宏弯损耗的温度响应特性

为了实现光纤宏弯温度传感,对单模光纤宏弯损耗的温度响应特性进行了理论与实验研究.理论上对单模光纤宏弯损耗理论公式进行了温度修正.基于该公式模拟了波长、弯曲半径以及温度对纤芯-无限包层结构单模光纤宏弯损耗性能的影响.设计制作了一种带吸收层和镍保护层的单模光纤宏弯温度传感探头并进行了温度传感性能实验测试.结果表明:纤芯-无限包层结构单模光纤宏弯损耗对弯曲半径、波长和温度变化较为敏感,与温度之间的响应呈线性,该探头的温度分辨率为0.4℃;通过减小弯曲半径和提高光源波长,可进一步提高其温度灵敏度和分辨率.该结构光纤可近似看作纤芯-无限包层结构光纤,用于开发光纤宏弯温度传感器.     

用于波导阵列——光纤阵列自动对接的多目标演化算法的研究

开发设计了一种新的列阵自动对接方法,该方法将多目标演化法导入光纤—光波导列阵—光纤列阵的自动对接,并行操作次数较常规遗传法大幅减少.数值仿真表明,对于模场非对称因子为0.4%的单模波导列阵与光纤列阵的双芯对接,能实现0.04 dB的平均端面耦合损耗.用于1×8波导分支耦合器与通道间距误差在0.35 μm以内的光纤列阵对接,自动耦合仿真达到了小于0.1 dB的平均端面耦合损耗,最大值与最小值的差小于0.06 dB.     

基于SPGD算法的少模光纤耦合解复用系统动态湍流补偿仿真

在空间光通信系统中,激光在大气中传输时容易受湍流效应影响,且接收端往往使用模场半径极小的单模光纤进行空间光耦合,导致光纤耦合效率降低,影响通信系统性能.为了提高接收端光纤耦合效率,结合随机并行梯度下降(SPGD)算法和少模光纤耦合解复用系统对动态湍流所引起的波前相位畸变进行补偿校正,并实现了传输距离为5 km的空间光通信数值仿真.仿真结果表明:在不同的湍流强度和风速条件下,未经SPGD算法校正时,两模光纤的耦合效率比单模光纤提高了0.5 dB～1.5 dB,相对标准差降低了0.03～0.4;经过SPGD算法校正后,两模光纤的耦合效率比单模光纤提高了0.4 dB～2.2 dB,中强湍流下,相对标准差降低了0.1～0.2.因此在空间光通信中,采用少模光纤进行耦合接收比单模光纤具有更好的耦合效果,有利于提高通信系统稳定性.     

Self-organization of five species in a cyclic competition game

Cyclic competition game models, particularly the “rock–paper–scissors” model, play important roles in exploring the problem of multi-species coexistence in spatially ecological systems. We propose an extended “rock–paper–scissors” game to model cyclic interactions among five species, and find that two of the five can coexistent when biodiversity disappears, which is different from the “rock–paper–scissors” game. As the number of fingers is five, we named the new model the “fingers” game, where the thumb, forefinger, middle finger, ring finger, and little finger cyclically dominate their subsequent species and are dominated by their former species. We investigate the “fingers” model in two ways: direct simulations and nonlinear partial differential equations. An important finding is that the number of species in a cyclic competition game has an influence on the emergence of biodiversity. To be specific, the “rock–paper–scissors” model is in favor of maintaining biodiversity in comparison with the “fingers” model when the variables (population size, reproduction rate, selection rate, and migration rate) are the same. It is also shown that the mobility and reproduction rate can promote or jeopardize biodiversity.     

Experimental study on downstep in Chinese intonation

Downstep in pitch contour of Chinese Putonghua is examined using subtly designed sentences by controlling tone combinations. The results show both automatic and nonautomatic downstep phenomena exist in Chinese. In non-automatic downstep, low tones compress downwards the pitch range of the following syllables. and the main influence of downstep is on topline. Low tone not only lower the topline behind it, but also raise the high tones before it, the effects are compatible with each other. In automatic downstep, the topline of pitch contour in intonational phrase is presented as a linear downtrend, but it differs among speakers due to the effect of personal stress practice. In comparison with downstep phenomenon in other tone or non-tone languages, the downstep ratio in Chinese is not constant, and the domain of downstep is not limited within the adjacent tones.     

Contrastive analysis on tone between Putonghua and Taiwan Mandarin

The differences of the pitch and duration of Chinese syllables between Putonghua （PTH） and Taiwan Mandarin （TM） were studied. The speech materials to be used are not only isolated syllables, but also sentences. The results reveal that： For the isolated syllables, T1 and T2 in TM are influenced by Minnan dialect, therefore their pitch are lower than those in PTH. T3 is fall-rise in PTH, while it is fall in TM. Moreover, the syllable duration sequence for different tone is T3〉T2〉T1〉T4 in PTH, while it is T1〉T2〉T3〉T4 in TM. For the syllables in sentences, T2 is mid-rise in PTH, while it is mid-level in TM. And the T3 is longer than T4 but shorter than T1 or T2 in PTH, while it is the shortest in TM. Furthermore the effects of prosodic phrase boundary on duration for different tones are almost the same in PTH, but the lengthening part of T1 or T2 is longer than that of T3 or T4 in TM.     

Abelian-Higgs phase of SU(2) QCD and glueball energy

It is shown that SU(2) QCD admits an dual Abelian-Higgs phase, with a Higgs vacuum of a type-Ⅱ superconductor. This is done by using a connection decomposition for the gluon field and the random-direction approximation. Using a bag picture with soft wall, we presented a calculational procedure for the glueball energy based on the recent proof for wall-vortices [Nucl. Phys. B 741(2006)1].     

Signal generation in an isotropic medium in scanning electron acoustic microscope

Based on the research in Ref. [5][Materials Science and Engineering, 1989; A122： 57 63], an improved model of heat source is set up, the different modes of Lamb wave in an isotropic sample generated by a chopped electron beam at frequency f are obtained with integral transform and normal function expansion method, and the output signal of PZT coupled at the back surface of the sample is found out. The generation mechanism of SEAM （Scanning Electron Acoustic Microscopy） signal is discussed. It shows that the SEAM is a near field imaging technique with high spatial resolution and its best lateral spatial resolution is about 2√2α （α is the radius of the focused electron beam）. Some of experimental results of SEAM images are presented in the paper and it shows that the spatial resolution of SEAM is better than 0.5 μm and smaller than the thermal diffusion length of the sample. Therefore the character of near field imaging in SEAM is also proved experimentally.     

High efficiency filtering using two-dimensional photonic crystal coupled cavity structures

Transmission spectra of coupled cavity structures (CCSs) in two-dimensional (2D) photonic crystals (PCs) are investigated using a coupled mode theory, and an optical filter based on CCS is proposed. The performance of the filter is investigated using finite-difference time-domain (FDTD) method, and the results show that within a very short coupling distance of about 3λ, where λ is the wavelength of signal in vacuum, the incident signals with different frequencies are separated into different channels with a contrast ratio of 20 dB. The advantages of this kind of filter are small size and easily tunable operation frequencies.     

Real-time restoration of rotational blurred image using gradient-loading

The key to the restoration of rotational motion blurred image is how to restore the image under a low cost and to correct the irreversibility of the degradation function matrix.Based on the special qualities of degradation function matrix and precise deduction in space-domain, we present a new approach using gradient-loading for restoration of rotational blurred image.By easily adding a gradient operator, the irreversibility of the original matrix is corrected and can be applied for inverse filtering then.Gradientloading is the optimized approach which combines the advantages of both the approaches using constrained least square filtering and traditional diagonal-loading.Compared with the approach using least square filtering, its peak signal-to-noise ratio (PSNR) is improved from 3.18 to 6.46dB, while the computing time is reduced to 1/2-1/3.Experimental results demonstrate the effectiveness, noise-resistibility, robustness, and low complexity of this approach, which make it more suitable for real-time environment.     

All-Optical Logic Device Using Bent Nonlinear Tapered Y-Junction Waveguide Structure

We propose an all-optical logic device made of a bent tapered Y-junction waveguide with a Kerr-type nonlinear interface. It could provide an AND gate, OR gate, and exclusive-OR (XOR) gate. We could obtain different transmission results by adjusting the bending angle. The numerical simulation results show that the device functions as AND, OR, and XOR gates.     

Real-time, continuous-wave terahertz imaging by a pyroelectric camera

Real-time, continuous-wave terahertz (THz) imaging is demonstrated. A 1.89-THz optically-pumped farinfrared laser is used as the illumination source, and a 124 × 124 element room-temperature pyroelectric camera is adopted as the detector. With this setup, THz images through various wrapping materials are shown. The results show that this imaging system has the potential applications in real-time mail and security inspection.