Positive linear magnetoresistance in Fex–C1−x composites

A large positive magnetoresistance (MR) has been found in micro-sized Fe_x–C_1−x composites. At a magnetic field of 5 T, the Fe_0.2–C_0.8 composite has the largest MR, 53.8% and 190% at room temperature and at 5 K, respectively. The magnetic field dependence of the MR can be described approximately as MR∝Bⁿ, and the value of exponent n is determined by the Fe weight concentration and temperature, ranging from 1/4 to 6/4. It appears that Fe_x–C_1−x has a linear field dependence of the positive MR at different temperatures. The possible mechanism for the positive MR is discussed.     

The influence of different fabrication processes on characteristics of excess Bi2O3-doped 0.95 (Na0.5Bi0.5)TiO3–0.05 BaTiO3 ceramics

In this study, we will develop the influences of the excess x wt% (x=0, 1, 2, and 3) Bi₂O₃-doped and the different fabricating process on the sintering and dielectric characteristics of 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃ ferroelectric ceramics with the aid of SEM and X-ray diffraction patterns, and dielectric–temperature curves. The 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ ceramics are fabricated by two different processes. The first process is that (Na_0.5Bi_0.5)TiO₃ composition is calcined at 850 °C and BaTiO₃ composition is calcined at 1100 °C, then the calcined (Na_0.5Bi_0.5)TiO₃ and BaTiO₃ powders are mixed in according to 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions. The second process is that the raw materials are mixed in accordance to the 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions and then calcining at 900 °C. The sintering process is carried out in air for 2 h from 1120 to 1240 °C. After sintering, the effects of process parameters on the dielectric characteristics will be developed by the dielectric–temperature curves. Dielectric–temperature properties are also investigated at the temperatures of 30–350 °C and at the frequencies of 10 kHz–1 MHz.     

Structural and electrical properties of crystalline (1−x)Ta2O5−xTiO2 thin films fabricated by metalorganic decomposition

Polycrystalline (1−x)Ta₂O₅−xTiO₂ thin films were formed on Si by metalorganic decomposition (MOD) and annealed at various temperatures. As-deposited films were in the amorphous state and were completely transformed to crystalline after annealing above 600 °C. During crystallization, a thin interfacial SiO₂ layer was formed at the (1−x)Ta₂O₅−xTiO₂/Si interface. Thin films with 0.92Ta₂O₅–0.08TiO₂ composition exhibited superior insulating properties. The measured dielectric constant and dissipation factor at 1 MHz were 9 and 0.015, respectively, for films annealed at 900 °C. The interface trap density was 2.5×10¹¹ cm⁻² eV⁻¹, and flatband voltage was −0.38 V. A charge storage density of 22.8 fC/μm² was obtained at an applied electric field of 3 MV/cm. The leakage current density was lower than 4×10⁻⁹ A/cm² up to an applied electric field of 6 MV/cm.     

Electric conductivity and relaxation in ZnF2–AlF3–PbF2–LiF glasses

The electric conductivity of ZnF₂–AlF₃–PbF₂–LiF glasses has been studied in the frequency range 10 Hz–2 MHz and in the temperature range from 300 K to just below the glass transition temperature. The conductivity decreases with the increase in the LiF content in the composition, which results from the trapping of F⁻ ions by Li⁺ ions. Small values of the stretching exponent β are observed for the present glasses. The value of the decoupling index decreases with an increase in LiF content, consistent with the composition dependence of the conductivity.     

Photo-operated two-photon absorption effects in the GeSe2–Ga2S3–PbI2 glasses

The possibility to operate the two-photon absorption (TPA) of newly synthesized GeSe₂–Ga₂S₃–PbI₂ glasses using the CO laser beam (λ=5.5 μm) as a photoinducing one has been demonstrated. As the fundamental laser beam we have used the illumination of 10.6 μm passively modulated 0.5 ns CO₂ laser with a rate repetition of about 10 Hz. We have established that the maximal photoinduced TPA is observed for the 8% doped samples (up to 14 cm/GW), which is achieved at a pump CO laser pump power density equal to about 0.6 GW/cm². The undoped PbI₂ samples show the TPA maximum at a pump power density of about 0.2 cm/GW. The minimal TPA values were observed for the samples with 5% of PbI₂. The obtained results show that these materials can be used as effective optically operated optical limiters.     

Optical and electrical properties of binary WO3–Pb3O4 glasses

A glass system of the composition xWO₃+(100−x)Pb₃O₄, with x=5, 10, 20 and 30 mol.% was prepared. The optical absorption, ac and dc conductivities are the subject of the present work. The optical absorption indicates that the electronic transition is indirect and is associated with phonon assisted transition. The exponential dependence of the absorption coefficient as a function of the incident photon energy suggests that the Urbach rule is obeyed, and indicates the formation of a band tail. On the other hand, ac conductivity measurements are performed in the frequency range 0.1–100 kHz, and in the temperature range 300–600 K. The results of the electrical conductivity are discussed on the basis of electronic glass conduction models. Correlated narrow-band limit for random sites and single polaron hopping model are found to describe the experimental results effectively. The dielectric constant was correlated to the optical band gap and a satisfactory relation was found. It was also possible to calculate the thermochromic properties from independent ac and dc measurements, and it was possible to evaluate the optical gap at 0 K by extrapolation.     

Magnetic properties of Lu2Co17−xSix single crystals

The Co-sublattice anisotropy in Lu₂Co₁₇ consists of four competitive contributions from Co atoms at crystallographically different sites in the Th₂Ni₁₇-type of crystal structure, which result in the appearance of a spontaneous spin-reorientation transition (SRT) from the easy plane to the easy axis at elevated temperatures. In order to investigate this SRT in detail and to study the influence of Si substitution for Co on the magnetic anisotropy, magnetization measurements were performed on single crystals of Lu₂Co_17−xSi_x (x=0−3.4) grown by the Czochralski method. The SRT in Lu₂Co₁₇ was found to consist of two second-order spin reorientations, “easy-plane”–“easy-cone” at T_SR1≈680 K and “easy-cone”–“easy-axis” at T_SR2≈730 K. Upon Si substitution for Co, both SRTs shift toward the lower temperatures in Lu₂Co₁₆Si (T_SR1≈75 K and T_SR2≈130 K) with the further onset of the uniaxial type of magnetic anisotropy in the whole range of magnetic ordering for Lu₂Co_17−xSi_x compounds with x>1 due to a weakening of the easy-plane contribution from the Co atoms at the 6g and 12k sites to the total anisotropy.     

Effects of substitution of Ti for Fe in BiFeO3 films prepared by sol–gel process

Ti substituted BiFe_1−xTi_xO_3+δ films have been prepared on indium–tin oxide (ITO)/glass substrates by the sol–gel process. The films with x=0.00–0.20 were prepared at an annealing temperature of 600 °C. X-ray diffraction patterns indicate that all films adopt R3m structure and the films with x=0 and 0.10 show pure perovskite phase. Cross-section scanning shows the thickness of the films is about 300 nm. Through 0.05 Ti substitution, the 2P_r increases to 8.30 μC/cm² from 2.12 μC/cm² of the un-substituted BiFeO₃ film and show enhanced ferroelectricity at room temperature. The 2P_r values are 2.63 and 0.44 μC/cm² for the films with x=0.01 and 0.2, respectively. Moreover, the films with x=0.05 and 0.10 show enhanced dielectric property since the permittivity increases near 150 at the same measuring frequency. Through the substitution of Ti, the leakage conduction is reduced for the films with x=0.05–0.20.     

Investigation of 1.3 μm emission in Nd-doped bismuth-based oxide glasses

Nd₂O₃-doped 43Bi₂O₃–xB₂O₃–(57−x)SiO₂–1.0Nd₂O₃ (x=57, 47, 39, 28.5, 19.5, 10, 0 mol%) bismuth glasses were prepared by the conventional melt-quenching method, and the Nd³⁺: ⁴F_3/2→⁴I_13/2 fluorescence properties had been studied in an oxide system Bi₂O₃–B₂O₃–SiO₂. The Judd–Ofelt analysis for Nd³⁺ ions in bismuth boron silicate glasses was also performed on the basis of absorption spectrum, and the transition probabilities, excited-state lifetimes, the fluorescence branching ratios, quantum efficiency and the stimulated emission cross-sections of ⁴F_3/2→⁴I_13/2 transition were calculated and discussed. The stimulated emission cross-sections of 1.3 μm were quite large due to a large refractive index of the host. Although the effective bandwidths decreased with increasing SiO₂ content, quantum efficiencies and stimulated emission cross-sections enhanced largely with increasing SiO₂ content.     

Material design of new lithium ionic conductor, thio-LISICON, in the Li2S–P2S5 system

A new lithium ionic conductor of the thio-LISICON (LIthium SuperIonic CONductor) family was found in the binary Li₂S–P₂S₅ system; the new solid solution with the composition range 0.0≤x≤0.27 in Li_3+5xP_1−xS₄ was synthesized at 700 °C and characterized by X-ray diffraction measurements. Its electrical and electrochemical properties were studied by ac impedance and cyclic voltammetry measurements, respectively. The solid solution member at x=0.065 in Li_3+5xP_1−xS₄ showed the highest conductivity value of 1.5×10⁻⁴ S cm⁻¹ at 27 °C with negligible electronic conductivity and the activation energy of 22 kJ mol⁻¹ which is characteristic of high ionic conduction state. The extra lithium ions in Li₃PS₄ created by partial substitution of P⁵⁺ for Li⁺ led to the large increase in ionic conductivity. In the solid solution range examined, the minimum conductivity was obtained for the compositions, Li₃PS₄ (x=0.0 in Li_3+5xP_1−xS₄) and Li₄P_0.8S₄ (x=0.2 in Li_3+5xP_1−xS₄); this conductivity behavior is similar to other thio-LISICON family with the general formula, Li_xM_1−yM_y′S₄ (M=Si, Ge, and M′=P, Al, Zn, Ga, Sb). Conduction mechanism and the material design concepts are discussed based on the conduction behavior and the structure considerations.     

Crystal structure, superconductivity and magnetic properties of the superconducting ferromagnets Gd1.4−xDyxCe0.6Sr2RuCu2O10 (x=0–0.6)

The structural, electrical and magnetic properties of the superconducting ferromagnets, Gd_1.4−xDy_xCe_0.6Sr₂RuCu₂O₁₀ (x=0–0.6) are systematically investigated as a function of Dy doping and temperature. These compounds are characterized by high temperature superconductivity (T_c ranging from 20 to 40 K depending upon the Dy content) co-existing with weak ferromagnetism with two magnetic transitions (T_M2 ranging from 95 to 106 K and T_M1 around 120 K). Doping with Dy gives no significant structural changes except for a minor change in the c/a ratio. However the superconducting transition temperature is significantly suppressed and magnetic ordering temperature enhanced on Dy doping. These effects are described and discussed.     

Sintering of glasses in the system RO–Al2O3–BaO–SiO2 (R=Ca, Mg, Zn) studied by hot-stage microscopy

Glass–ceramics for sealing solid oxide fuel cells (SOFCs) were developed by sintering and crystallization of the powdered glass seal. The non-isothermal sintering kinetics and crystallization kinetics were studied for four glasses in the system 50SiO₂·(45−x)BaO·xRO·5Al₂O₃ (R=Ca, Mg, Zn and x=0, 15) (mol%). Hot-stage microscopy (HSM) and differential thermal analysis (DTA) measurements demonstrated that it is possible to first sinter and then crystallize these glasses obtaining glass–ceramic seals with thermal expansion coefficients in the range 9–12×10⁻⁶ K⁻¹.

The non-isothermal sintering kinetics was analyzed by computer simulations using a previously reported model of sintering for polydispersed glass powders which takes into account the particle size distribution, surface energy and viscosity. Good agreement was found between the measured kinetics with HSM and the calculated kinetics for all glasses.     

Oxygen diffusion and surface exchange in La1−xSrxFe0.8Cr0.2O3−δ (x=0.2, 0.4 and 0.6)

Oxygen tracer diffusion (D*) and surface exchange rate constant (k*) have been measured, using isotopic exchange and depth profiling by secondary ion mass spectrometry (SIMS), in La_1−xSr_xFe_0.8Cr_0.2O_3−δ (x=0.2, 0.4 and 0.6). Measurements were made as a function of temperature (700–1000 °C) and oxygen partial pressure (0.21–10⁻²¹ atm) in dry oxygen, water vapour and water vapour/hydrogen/nitrogen mixtures. At high oxygen activity, D* was found to increase with increasing temperature and Sr content. The activation energies for D* in air are 2.13 eV (x=0.2), 1.53 eV (x=0.4) and 1.21 eV (x=0.6). As the oxygen activity decreases, D* increases as expected qualitatively from the increase in oxygen vacancy concentration. Under strongly reducing conditions, the measured values of D* at 1000 °C range from 10⁻⁸ cm² s⁻¹ for x=0.2 to 10⁻⁷ cm² s⁻¹ for x=0.4 and 0.6. The activation energies determined at constant H₂O/H₂ ratio are 1.21 eV (x=0.2), 1.59 eV (x=0.4) and 0.82 eV (x=0.6).

The surface exchange rate constant of oxygen for the H₂O molecule is similar in magnitude to that for the O₂ molecule and both increase with increasing Sr concentration.     

Lithium insertion to ReO3-type metastable phase in the Nb2O5–WO3 system

Lithium insertion to distorted ReO₃-type metastable solid solution Nb_xW_1−xO_3−x/2 (0≤x<0.25) has been studied by chemical and electrochemical methods. In the course of lithium insertion into tetragonal compounds, transition to a cubic phase was found to occur in the region where values of y (in Li_yNb_xW_1−xO_3−x/2) fall between 0.2 and 0.3, and the phase transition was found to depend on the conditions of the reaction. Changes in OCV and lattice parameters in tetragonal region (y<0.2) were discussed from the viewpoint of the ordering of lithium ions. Also, the component diffusion coefficient of lithium in tetragonal compounds Li_0.1Nb_xW_1−xO_3−x/2 (0≤x≤0.23) was found to increase with niobium content when x≤0.10, and to saturate at 4×10⁻⁹ cm²/s.     

The order of magnetic phase transition in La(Fe1−xCox)11.4Si1.6 compounds

Magnetic transitions in La(Fe_1−xCo_x)_11.4Si_1.6 compounds with x=0–0.08, have been studied by DC magnetic measurements and Mössbauer spectroscopy. The temperature dependence of the Landau coefficients has been derived by fitting the magnetization, M(μ₀H), using the Landau expansion of the magnetic free energy. For x0.02 there is a strongly first-order magnetic phase transition between ferromagnetic and paramagnetic (F–P) states in zero external field and a metamagnetic transition from paramagnetic to ferromagnetic (P–F) above T_c. Increasing the cobalt content drives the F–P transition towards second order and eliminates the metamagnetic transition.     

Characterization of nonstoichiometric nickel manganite spinels NixMn3−x□3δ/4O4+δ by temperature programmed reduction

Cation deficient spinels Ni_xMn_3−x□_3δ/4O_4+δ (0≤x≤1) have been prepared by thermal decomposition of mixed oxalates Ni_x/3Mn_(3−x)/3(C₂O₄)·nH₂O in air at 623 K. They have been characterised by temperature programmed reduction (TPR) under H₂, the reaction being followed by gravimetric and powder X-ray diffraction measurements. It has been shown that TPR proceeds in several steps. The first steps correspond to the loss of nonstoichiometric oxygen leading to the formation of a stoichiometric oxide. During the following stages the manganese cations are reduced, causing the spinel structure to be destroyed, and the formation of solid solution of NiO in a cubic MnO. Subsequently, Ni²⁺ cations undergo a reduction to metallic nickel, and, finally, a mixture of nonstoichiometric MnO_1−δ and metallic nickel is formed. These oxides contain a high level of vacancies which vary with the nickel content with a maximum of δ≈1 near x=0.6. This nonstoichiometry is ascribed both to the presence of Ni³⁺ and excess of Mn⁴⁺.     

Higher-order elastic constants of La1.84Sr0.16CuO4 high-temperature superconductor

Finite deformation theory is used to obtain the strain energy density of a tetragonal 2–1–4-type single crystal of the high-temperature superconductor La_2−xSr_xCuO₄. The complete set of second and third-order elastic constants of the high-temperature superconductor La_2−xSr_xCuO₄ (x = 0.16) is calculated by taking into account the interactions between nine nearest-neighbour atoms in the lattice and using Mie–Grüneisen interatomic potential. For the sake of comparison we have also computed the values of these constants for x = 0.13–0.20. The values of third-order elastic constants of La_2−xSr_xCuO₄ (x = 0.13–0.20) are negative and their absolute magnitudes are one order higher than those of the second-order elastic constants.     

B-MQMAS and Si–{B} Double-Resonance NMR Studies on the Structure of Binary B2O3–SiO2 Glasses

Glasses in the system x B₂O₃·(1−x)SiO₂ (0.2≤x≤1.0) were studied using ¹¹B multiple quantum magic angle spinning NMR spectroscopy (MQMAS), ²⁹Si–\{¹¹B\} rotational echo adiabatic passage double-resonance and ²⁹Si–\}¹¹B\{ CP heteronuclear correlation spectroscopy. The results can be quantitatively interpreted in terms of a phase separation of the borosilicate glasses into a virtually SiO₂-free B₂O₃ phase and a mixed borosilicate phase. While the MQMAS spectra allowed the site speciation and resolution of at least two different ¹¹B resonances, attributable to BO_3/2 units consumed in boroxol rings, BO_3/2 units connecting the boroxol rings and BO_3/2 units involved in B–O–Si linkages, the analysis of the double-resonance data further elucidated the structure of the mixed borosilicate phase. The results indicate that only a fraction of 0.48 mol B₂O₃ can be accommodated per mole SiO₂, building a mixed borosilicate network.     

Ionic conduction and dielectric relaxation in Ag/Na ion-exchanged aluminosilicate glasses: mixed mobile ion effect and KWW relaxation

Ag⁺/Na⁺ ion-exchanged aluminosilicate glasses with uniform concentration profiles were prepared, and their electrical conductivities were investigated as functions of the ion-exchange ratio and the initial glass compositions. In the case of the ion-exchanged glasses of x20Ag₂O–(1−x)20Na₂O–10Al₂O₃–70SiO₂ in mol%, the conductivity, σ, and its activation energy, E_σ, showed a minimum and a maximum at the same ion-exchange ratio x=0.3, respectively, and the mixed mobile ion effect (MMIE) was observed. The fully ion-exchanged sample attained σ=3.5×10⁻⁵ S/cm at 200 °C, which was 1.5 orders of magnitude larger than that of initial glass. In the case of x25Ag₂O–(1−x)25Na₂O–25Al₂O₃–50SiO₂, the mixed mobile ion effect was also observed at x=0.5. The maximum conductivity of 2×10⁻⁴ S/cm at 200 °C was obtained in the fully ion-exchanged glass sample.

The electric relaxation analysis was also conducted on both systems, and Kohlrausch–Williams–Watts (KWW) fractional exponent β was obtained as a function of x. The decrease of β was observed near x≈0.3 in the former system, while that of the later system was independent of the ion-exchange ratio. Based on the structural analysis results, the observed behaviors were investigated from the point of view of the occupation of Ag⁺ ions on the non-bridging oxygen-site (NBO-site) and the charge compensation-site (CC-site) of AlO₄ tetrahedral unit.     

Ionic conduction in dilute pseudo-binary systems CuBr–Cu2Se

Ionic conductivity, σ_i, of dilute pseudobinary alloys (CuBr)_1−x(Cu₂Se)_x (x≤0.1) in their γ-phase has been measured by an ac method. The increase of the ionic conductivity propertional to x has been observed, which is attributed to interstitial ions brought by Cu₂Se dissolved in CuBr. It is found that the temperature dependence of mobility of interstitial ions, μ, evaluated by the relation Δσ_i/x=kμ (k is a constant) is bent at the temperature corresponding to the extrinsic–intrinsic transition of the based material CuBr.