A quantum cascade laser-based optical feedback cavity-enhanced absorption spectrometer for the simultaneous measurement of CH4 and N2O in air

Optical feedback cavity-enhanced absorption spectroscopy (OF CEAS) has been demonstrated with a thermoelectrically cooled continuous wave distributed feedback quantum cascade laser (QCL) operating at wavelengths around 7.84 μm. The QCL is coupled to an optical cavity which creates an absorption pathlength greater than 1000 m. The experimental design allows optical feedback of infra-red light, resonant within the cavity, to the QCL, which initiates self-locking at each TEM₀₀ cavity mode frequency excited. The QCL linewidth is narrowed to below the mode linewidth, greatly increasing the efficiency of injection of light into the cavity. At the frequency of each longitudinal cavity mode, the absorption coefficient of an intracavity sample is obtained from the transmission at the mode maximum, measured with a thermoelectrically cooled detector: spectral line profiles of CH₄ and N₂O in ambient air were recorded simultaneously and with a resolution of 0.01386 cm^?1. A minimum detectable absorption coefficient of 5.5×10^?8 cm^?1 was demonstrated after an averaging time of 1 s for this completely thermoelectrically cooled system. The bandwidth-normalised limit for a single cavity mode is 5.6×10^?9 cm^?1?Hz^?1/2 (1σ).     

Use of cw-CRDS for studying the atmospheric oxidation of acetic acid in a simulation chamber

The coupling between cavity ring-down spectroscopy (CRDS) and an environmental chamber in the investigation of photo-induced reaction mechanisms is demonstrated for the first time. The development of the CRDS device and the corresponding analytical performances are presented. The first application is devoted to the investigation of the branching ratio of the ^?OH radical reaction of CH₃C(O)OH and CH₃C(O)OD under tropospheric conditions. An environmental chamber coupled to two complementary detection systems is used:

gas chromatography with FTIR spectroscopy for quantitative detection of acetic acid;

CRDS for quantitative detection of CO₂.

Investigation of the reaction kinetics of ^?OH+CH₃C(O)OH gives a rate constant of (6.5±0.5)×10^-13 cm³?molecule^-1?s^-1 (296 K) and shows good agreement with literature data. The product study indicates that the H-abstraction channel from the acid group is the dominant pathway with a branching ratio of (78±13)%, whereas the corresponding D-abstraction channel in the ^?OH+CH₃C(O)OD reaction represents only (36±7)%. This result could be attributed to a strong kinetic isotope effect. Glyoxylic acid has also been detected for the first time as by-product. These results illustrate the high interest of the CRDS technique in the investigation of atmospheric relevant problems.     

Using a DS-DBR laser for widely tunable near-infrared cavity ring-down spectroscopy

Studies into the suitability of a novel, widely tunable telecom L-band (1,563–1,613 nm) digital supermode distributed Bragg reflector (DS-DBR) laser for cavity ring-down spectroscopy (CRDS) are presented. The spectrometer comprised of a 36.6?cm long linear cavity with ring-down times varying between 19–26 μs across the 50 nm DS-DBR wavelength range due to changes in the cavity mirror reflectivities with wavelength. The potential of such a broadband, high-resolution CRD spectrometer was illustrated by investigating several transitions of CO₂ in air, a 5 % calibrated mixture and breath samples. Allan variance measurements at a single wavelength indicated an optimal minimum detectable absorption coefficient (α _min) of 3 × 10^?10 cm^?1 over 20 s.     

A compact resonant Π-shaped photoacoustic cell with low window background for gas sensing

A resonant photoacoustic cell capable of detecting the traces of gases at an amplitude-modulation regime is represented. The cell is designed so as to minimize the window background for the cell operation at a selected acoustic resonance. A compact prototype cell (the volume of acoustic cavity of ~0.2 cm³, total cell weight of 3.5 g) adapted to the narrow diffraction-limited beam of near-infrared laser is produced and examined experimentally. The noise-associated measurement error and laser-initiated signals are studied as functions of modulation frequency. The background signal and useful response to light absorption by the gas are analyzed in measurements of absorption for ammonia traces in nitrogen flow with the help of a pigtailed DFB laser diode operated near a wavelength of 1.53 µm. The performance of absorption detection and gas-leak sensing for the prototype operated at the second longitudinal acoustic resonance (the resonance frequency of ~4.38 kHz, Q-factor of ~13.9) is estimated. The noise-equivalent absorption normalized to laser-beam power, and detection bandwidth is ~1.44 × 10^?9 cm^?1 W Hz^?1/2. The amplitude of the window-background signal is equivalent to an absorption coefficient of ~2.82 × 10^?7 cm^?1.     

Frequency-agile,rapid scanning spectroscopy: absorption sensitivity of 2 × 10−12 cm−1 Hz−1/2 with a tunable diode laser

We present ultrasensitive measurements of molecular absorption using frequency-agile rapid scanning, cavity ring-down spectroscopy with an external-cavity diode laser. A microwave source that drives an electro-optic phase modulator with a bandwidth of 20 GHz generates pairs of sidebands on the probe laser. The optical cavity provides for high sensitivity and filters the carrier and all but a single, selected sideband. Absorption spectra were acquired by stepping the tunable sideband from mode-to-mode of the ring-down cavity at a rate that was limited only by the cavity decay time. This approach allows for scanning rates of 8 kHz per cavity resonance, a minimum detectable absorption coefficient of 1.7 × 10^?11 cm^?1 after only 20 ms of averaging, and a noise-equivalent absorption coefficient of 1.7 × 10^?12 cm^?1 Hz^?1/2. By comparison with cavity-enhanced laser absorption spectrometers reported in the literature, the present system is, to the best of our knowledge, among the most sensitive and has by far the highest spectrum scanning rate.     

Time resolved simultaneous detection of 14NO and 15NO via mid-infrared cavity leak-out spectroscopy

We present a ring-down absorption spectrometer based on a continuous-wave CO laser in the mid-infrared spectral region near λ?=?5 μm. Using a linear ring-down cavity (length: 0.5 m) with high reflective mirrors (R?=?99.988 %), we observed a noise-equivalent absorption coefficient of 3?×?10^?10 cm^?1Hz^?1/2. This corresponds to a noise-equivalent concentration of 800 parts per trillion (ppt) for ¹⁴NO and 40 ppt for ¹⁵NO in 1 s averaging time. We achieve a time resolution of 1 s which allows time resolved simultaneous detection of the two N isotopes. The δ¹⁵N value was obtained with a precision of ±1.2‰ in a sample with a NO fraction of 11 ppm. The simultaneous detection enables the use of ¹⁵NO as a tracer molecule for endogenous biomedical processes.     

Optical-feedback cavity-enhanced absorption spectroscopy with a quantum-cascade laser yields the lowest formaldehyde detection limit

We report on the first application of Optical Feedback-Cavity Enhanced Absorption Spectroscopy to formaldehyde trace gas analysis at mid-infrared wavelengths. A continuous-wave room-temperature, distributed-feedback quantum cascade laser emitting around 1,769 cm^?1 has been successfully coupled to an optical cavity with finesse 10,000 in an OF-CEAS spectrometer operating on the ν₂ fundamental absorption band of formaldehyde. This compact setup (easily transportable) is able to monitor H₂CO at ambient concentrations within few seconds, presently limited by the sample exchange rate. The minimum detectable absorption is 1.6 × 10^?9 cm^?1 for a single laser scan (100 ms, 100 data points), with a detectable H₂CO mixing ratio of 60 pptv at 10 Hz. The corresponding detection limit at 1 Hz is 5 × 10^?10 cm^?1, with a normalized figure of merit of 5 × 10^?11cm $^{-1}/\sqrt{\rm Hz}$ (100 data points recorded in each spectrum taken at 10 Hz rate). A preliminary Allan variance analysis shows white noise averaging down to a minimum detection limit of 5 pptv at an optimal integration time of 10 s, which is significantly better than previous results based on multi-pass or cavity-enhanced tunable QCL absorption spectroscopy.     

Off-beam quartz-enhanced photoacoustic spectroscopy with LEDs

A photoacoustic ozone sensor based on quartz-enhanced photoacoustic spectroscopy is presented. Instead of a laser, a UV-LED at 285 nm is utilized as light source. Using an acoustical resonator in off-beam configuration, it is feasible to align the light of the LED through the resonator tube. The sensor is integrated in a miniaturized flow-through gas cell which allows fast gas exchange. The sensor performance and the influence of the speed of sound on the measurement signal are investigated. For the detection of ozone in the Hartley band, a detection limit of S = 1.27 ± 0.08 ppmv (1σ) and a noise equivalent absorption sensitivity of D = (3.02 × 10^?8 ± 1 × 10^?10) cm^?1W(Hz)^?1/2 have been achieved.     

C2H2 Overtones Near 12300 cm-1 Revisited with a Very Sensitive Cavity Ring-down Spectrometer

利用单模连续的钛宝石激光器, 构建了一台光腔衰荡光谱仪, 其可探测的最小吸收可达1.8×10^-10/cm. 该光谱仪被用来记录C₂H₂分子在12240～12350 cm^-1的泛频光谱. 与在同一波段测量的已报到的CRDS和激光腔内吸收光谱仪结果比较,本测量同时具有更好的灵敏度和精度. 由此,获得了乙炔分子在12290.12、12311.82和12350.61 cm^-1附近高泛频谱带更准确的振转参数     

High-sensitivity CRDS absorption spectroscopy of acetylene between 5851 and 6341 cm−1

The absorption spectrum of acetylene has been recorded at room temperature (297 K) using high-sensitivity cavity ring-down spectroscopy (α_min ～ 5×10^?11 cm^?1) in the 5851 and 6341 cm^?1 interval corresponding to a region of very weak absorption. A list of about 10,700 absorption features with estimated absolute line intensities was constructed. The smallest intensities are of the order of 5×10^?29 cm molecule^?1. The line list includes about 2500 absorption lines of ethylene present at the ppm level in the acetylene sample and identified on the basis of a high-resolution Fourier transform spectrum specifically recorded. A total of more than 2700 lines of ¹²C₂H₂ were rovibrationally assigned in comparison with accurate predictions provided by a global effective operator model. Overall, the present effort adds about 2260 new assignments to the set of about 500 assigned transitions available in the literature. The new assignments correspond to 45 new bands and 17 already-known bands, for which additional J lines were assigned. Spectroscopic parameters were derived for the upper vibrational levels from a band by band fit of the line positions (typical root mean square deviation values are of the order of 0.001 cm^?1). A few of the analysed bands were found to be affected by rovibrational perturbations, which are discussed. The new data will be valuable to refine the parameters of the global effective Hamiltonian and dipole moments of ¹²C₂H₂.     

Rapid determination of ethyl pentanoate in liquor using Fourier transform near-infrared spectroscopy coupled with chemometrics

ABSTRACT

The feasibility of Fourier transform near-infrared spectroscopy for rapid determination of ethyl pentanoate in Chinese liquor was investigated. A total of 108 liquor samples from production line were analyzed with Fourier transform near-infrared transmission spectroscopy. The calibration model for ethyl pentanoate content prediction was established with partial least square, and validated using internal cross validation. In a calibration set (80 samples), the coefficient of determination was 0.958, with the corresponding root mean square error of cross validation 0.020 g L^?1. In a validation set (28 samples), the coefficient of determination was 0.964, with the root mean square errors of prediction 0.023 g L^?1, and the bias value (0.005 g L^?1) for the validation set was less than the bias confidence limits value (0.009 g L^?1), indicating that the resulting near-infrared spectroscopy prediction model has good performance for online rapid determination of ethyl pentanoate in Chinese liquor. The determination of ethyl pentanoate in liquor can be completed in less than 2 min per sample using the near-infrared spectroscopy prediction model. The near-infrared spectroscopy combining chemometrics as a rapid analytical method has a promising application prospect of application in the liquor production field.     

Characterisation of the potential of frequency modulation and optical feedback locking for cavity-enhanced absorption spectroscopy

A combination of optical feedback self-locking of a continuous-wave distributed feedback diode laser to a V-shaped high finesse cavity, laser phase modulation at a frequency equal to the free spectral range of the V-cavity and detection of the transmitted laser beam at this high modulation frequency is described for the possible application in cavity-enhanced absorption spectroscopy. In order to estimate the noise level of an absorbance baseline, the triplet of frequency modulated light, i.e. the central laser frequency and the two sidebands, were transmitted through both the V-cavity in open air and a 1.5-cm long optical cell placed behind the cavity output mirror and filled with acetylene (C₂H₂) at low pressure. The performance of the setup was evaluated from the measured relative intensity noise on the cavity output (normalised by the bandwidth) and the frequency modulation absorption signals induced by C₂H₂ absorption in the 1.5-cm cell. From these data, we estimate that the noise-equivalent absorption sensitivity of 2.1 × 10^?11 cm^?1 Hz^?1/2—by a factor of 11.7 above the shot-noise limit—can be achieved for C₂H₂ absorption spectra extracted from the heterodyne beat signals recorded at the transmission maxima intensity peaks of the successive TEM₀₀ resonances.     

Cavity-enhanced optical feedback-assisted photo-acoustic spectroscopy with a 10.4 μm external cavity quantum cascade laser

An ultra-sensitive photo-acoustic spectrometer using a 10.4 μm broadly tunable mid-IR external cavity quantum cascade laser (EC-QCL) coupled with optical feedback to an optical power buildup cavity with high reflectivity mirrors was developed and tested. A laser optical power buildup factor of 181 was achieved, which corresponds to an intra-cavity power of 9.6 W at a wavelength of 10.4 μm. With a photo-acoustic resonance cell placed inside the cavity this resulted in the noise-equivalent absorption coefficient of 1.9 × 10^?10 cm^?1 Hz^?1/2, and a normalized noise-equivalent absorption of 1.1 × 10^?11 cm^?1 W Hz^?1/2. A novel photo-acoustic signal normalization technique makes the photo-acoustic spectrometer’s response immune to changes and drifts in the EC-QCL excitation power, EC-QCL to cavity coupling efficiency and cavity mirrors aging and contamination. An automatic lock of the EC-QCL to the cavity and optical feedback phase optimization permitted long wavelength scans within the entire EC-QCL spectral tuning range.     

Spectroscopic Determination of Cysteine with Alizarin Red S and Copper

ABSTRACT

The interaction between metal complex Cu²⁺–ARS (Alizarin Red S) and l-cysteine was investigated via fluorescence and absorption spectroscopies. In pH 5.2 Britton–Robinson buffer, the addition of L-cysteine into Cu²⁺–ARS system resulted in a fluorescence enhancement because cysteine reduced Cu²⁺ to Cu⁺, which led to Cu²⁺–ARS decompound, and ARS was released. The result was also supported by absorption spectroscopy change. A good linear response of fluorescence intensity as a function of cysteine concentration was obtained ranging from 1.0 × 10^?6 to 4.0 × 10^?5 mol L^?1 with the detection limit as 1.08 × 10^?7 mol L^?1. The introduced method has high selectivity over other amino acids such as cystine, tyrosine, tryptophan, methionine, and glycine. It was applied to determine cysteine in protein hydrolysate of fresh pig blood with recovery of 88.4–100.2%.     

EPR and Optical Absorption Study of Cr3+-Doped Dipotassium Tetrachloropalladate

X-band electron paramagnetic resonance (EPR) study of Cr³⁺-doped dipotassium tetrachloropalladate single crystal is done at liquid nitrogen temperature. EPR spectrum shows two sites. The spin-Hamiltonian parameters have been evaluated by employing hyperfine resonance lines observed in EPR spectra for different orientations of crystal in externally applied magnetic field. The values of spin-Hamiltonian and zero-field splitting (ZFS) parameters of Cr³⁺ ion-doped DTP for site I are: g _x  = 2.096 ± 0.002, g _y  = 2.167 ± 0.002, g _z  = 2.220 ± 0.002, D = (89 ± 2) × 10^?4 cm^?1, E = (16 ± 2) × 10^?4 cm^?1. EPR study indicates that Cr³⁺ ion enters the host lattice substitutionally replacing K⁺ ion and local site symmetry reduces to orthorhombic. Optical absorption spectra are recorded at room temperature. From the optical absorption study, the Racah parameters (B = 521 cm^?1, C = 2,861 cm^?1), cubic crystal field splitting parameter (Dq = 1,851 cm^?1) and nephelauxetic parameters (h = 2.06, k = 0.21) are determined. These parameters together with EPR data are used to discuss the nature of bonding in the crystal.     

Line broadening,shifting and mixing parameters for the ν1 + ν3 band of OCS perturbed by N2 and O2

In this paper, we report measured Rosenkranz N₂- and O₂-broadening, induced pressure-shift and mixing coefficients for OCS in the ν₁ + ν₃ band, using a multi-pressure fitting technique applied to the measured shapes of the lines, including the interference effects caused by the line overlaps. These measurements were made by analysing six laboratory absorption spectra recorded at 0.004 cm^?1 resolution using the Fourier transform spectrometer Bruker IFS125HR located at the Laboratoire Interuniversitaire des Systèmes Atmosphériques, in Créteil. The spectra have been recorded in the 1850–3000 cm^?1 wave number range at 295 K, using a multipass absorption cell with an optical path of 3.249 m. The total sample pressures ranged from 5.97 to 83.28 Torr with OCS volume mixing ratios between 0.001 and 0.013 in nitrogen or oxygen. We have been able to determine the N₂- and O₂-pressure-broadening coefficients of 81 ν₁ + ν₃ transitions with rotational quantum number J up to 50. The measured N₂- and O₂-broadening coefficients range from 0.0815 ± 0.0698 to 0.1169 ± 0.1027 cm^?1 atm^?1 at 295 K, respectively. Most of the measured pressure shifts are positive. The reported N₂- and O₂-induced pressure-shift coefficients vary from about ?0.0103 ± 0.0092 to 0.0097 ± 0.0092 cm^?1 atm^?1, respectively. We have examined the dependence of the measured broadening parameters on the quantum number m (m = ?J for the P branch and m = J + 1 for the R branch) and also developed an empirical expression to describe the broadening coefficients in terms of |m|. On average, this empirical expression reproduces the measured broadening coefficients to within 2%. Using a semi-classical Robert and Bonamy formalism, the theoretical broadening coefficients have been calculated at room temperature and compared with the experimental results. The theoretical results of the broadening coefficients are in very good overall agreement with the experimental data (2%).     

Microspherical ZnO synthesized from a metal-organic precursor for supercapacitors

In this paper, ZnO microspheres, which are composed of irregular nanoparticles, have been synthesized successfully from a metal-organic precursor. The average diameter is about 3.5 μm and the specific surface area is 7.53 m² g^?1. Measured by electrochemical tests as electrode materials for supercapacitors, the ZnO powders show high specific capacitances (1017.5 Fg^?1 at 5 Ag^?1 and 562.5 Fg^?1 at 50 Ag^?1, respectively) and excellent cycling stability (the specific capacitance was kept at 631.2 Fg^?1 and 89.2 % retention after 3000 cycles at 18 Ag^?1). These results show that the microspherical ZnO could be a potential electrode material for supercapacitors.     

Near Infrared Spectroscopy of Benzoic Acid Adsorbed on Montmorillonite

ABSTRACT

The adsorption of benzoic acid on both sodium and calcium montmorillonites has been studied by near infrared spectroscopy complimented with infrared spectroscopy. Upon adsorption of benzoic acid, additional near-infrared bands are observed at 8665 cm^?1 and assigned to an interaction of benzoic acid with the water of hydration. Upon adsorption of the benzoic acid on Na-Mt, the NIR bands are now observed at 5877, 5951, 6028, and 6128 cm^?1 and are assigned to the overtone and combination bands of the CH fundamentals. Additional bands at 4074, 4205, 4654, and 4678 cm^?1 are attributed to CH combination bands resulting from the adsorption of the benzoic acid. Benzoic acid is used as a model molecule for adsorption studies. The application of near-infrared spectroscopy to the study of adsorption has the potential for the removal of acids from polluted aqueous systems.     

17O12C17O and 18O12C17O spectroscopy in the 1.6 μm region

Near infrared spectra of a carbon dioxide sample enriched with oxygen-17 have been recorded using a high-resolution continuous scan Fourier transform interferometer fitted with a femto OPO/Idler laser source. Cavity enhanced absorption has been achieved in a static gas cell allowing an optimal rms noise equivalent absorption of 1.2?×?10^?10?cm^?1?Hz^?1/2 per spectral element to be reached, corresponding to α_min?=?10^?8?cm^?1. Spectra were calibrated against acetylene reference line positions. Three bands in the 3ν₁?+?ν₃ tetrad in both ¹²C¹⁷O₂ and ¹²C¹⁷O¹⁸O have been identified and rotationally analyzed, as well as some related hot bands, eight of which are newly reported and three with their analysis updated compared with a preliminary report (X. de Ghellinck d’Elseghem Vaernewijck et al., Chem. Phys. Lett. 514, 29 (2011)).     

SPECTROPHOTOMETRIC DETERMINATION OF ZINC IN PHARMACEUTICAL SAMPLES USING DI-2-PYRIDYL KETONE SALICYLOYLHYDRAZONE

ABSTRACT

A highly sensitive procedure for spectrophotometric determination of zinc has been developed. At pH 4.5, in 50% (V/V) ethanol-water medium and in the presence of di-2-pyridyl ketone salicyloylhydrazone (DPKSH), zinc forms a yellow complex which has maximum absorption at 376 nm The molar absorptivity is 4.82×10⁴ L mol^?1 cm^?1. The detection limit of this method is 62.1 nM for Zn(II).

The method has been applied to the spectrophotometric determination of zinc in pharmaceutical formulations and the results comply with those obtained by AAS. The proposed method is simple, rapid and accurate.