小波变换在载频条纹相位分析法中的应用研究

为了克服在非平稳信号分析中傅里叶变换的全局性缺陷,以及窗口傅里叶分析的单一分辨率和伸缩窗口傅里叶分析的尺度不确定性问题,采用伽博解析小波变换技术对空间载频光栅条纹进行相位分析,有效地提取出相对于载频条纹基频的完整相位信息,从本质上解决了上述问题。以三维轮廓术为例,与傅里叶分析进行了对比研究,给出了小波分析应用在空间载频条纹相位分析中详细而完整的理论推导证明、计算机模拟以及实验验证结果。     

傅里叶变换轮廓术中物体高度最佳恢复条件

在分析傅里叶变换轮廓术中传统的高度与相位关系的基础上,推出了高度与相位的普通关系式,提出了物体高度最佳恢复条件的新理论,给出了简单的物理解释.由此得出结论：物体高度最佳恢复时的几何参量α（双瞳连线与参考面夹角）大小与系统几何结构参量a、b有关.计算机仿真验证了：当a=600 mm、b=3 000 mm时,可得物体高度最佳恢复时的α=arcsin (1/5),此时所得的标准差为0.269 7;作为对比：当α=0时,所得的标准差为0.295 6.实验验证了：α=arcsin (1/5)时的恢复效果比α=0时的恢复效果更好些.     

相位测量轮廓术中三维坐标校准新方法

提出了一种新的用于相位测量轮廓术中的三维坐标校准方法。该方法用一个含有三个虚拟校准平面的标准块代替传统相位测量轮廓术校准方法中使用的标准平面，每个虚拟校准平面由多个高度相同但空间离散分布的子区域组成，相应的连续相位恢复是通过一个迭代过程实现的，同时各个子区域还被用于横向坐标的校准。由于各个虚拟校准平面间高度是垂直变化的，传统的相位展开不能得到正确的相对位置关系，基于等效波长概念，提出了一种准确的虚拟校准平面连续相位间相对位置恢复的办法。此校准方法的特点是：在校准过程中不需要标准平面的多次精确平移；仅需要一次测量就可以完成高度和横向坐标的同时校准。文中给出的实验结果说明了该校准方法的有效性和可行性。     

非线性系统的非对角Berry相

研究了非线性系统中非对角情况的Berry相位, 给出了非线性非对角Berry相位的计算公式. 结果表明, 在非线性非对角情况下, 总相位包含有动力学相位, 通常意义的Berry相位, 以及非线性引起的附加相位. 此外, 还包含有非对角情况时所特有的新的附加项. 这新的一项表示, 当系统哈密顿慢变时产生的Bogoliubov涨落, 与另一个瞬时本征态之间的交叉效应, 进而对总的Berry相位产生影响. 作为应用, 对二能级玻色爱因斯坦凝聚体系, 具体计算了非线性非对角的Berry相位. 关键词： Berry 相位 非对角 绝热演化 玻色爱因斯坦凝聚     

改进傅里叶变换轮廓术的测量算法研究

提出一种适用于更普遍情况的计算方法.推导了投影装置与成像装置双瞳不等高且双轴不共面时的条纹获取公式.推导出新的相位获取公式以及相位高度映射公式.使得系统可以在双瞳连线不平行参考面,且双光轴也不共面时进行正确的三维测量.与传统的傅里叶变换轮廓术(FTP)相比,该算法实验系统的搭建更容易,投影装置和成像装置的摆放位置町以随意移动以方便全场条纹的获取;与改进的傅里叶变换轮廓术(IFTP)相比,只需要对系统测量三个长度量,系统参量的获取更容易和准确,从而误差变小,测量结果更加接近真实.     

傅里叶变换轮廓术定标实验研究

基于傅里叶轮廓变换术,研究对三维相位图进行定标,即标定调制相位与高度的定量关系的方法.首先,推导实验用的高度与调制相位的定标公式;然后,使用周期为3个像素的光栅条纹,以高度问隔分别为50μm,1 mm,2 mm,5 mm进行定标实验,并应用定标公式对沿高度方向的包裹相位进行解包.     

一种三次非旋转对称的相位板的检测系统设计

作为零位干涉检测方法中非常有前途的一种方法.计算全息可以用于非旋转对称的非球面的检测.以三次相位板为例,阐述了利用计算全息图检测非旋转对称的非球面的基本原理.分析并推导了三次相位传播过程引入的高阶波像差的理论公式,给出了三次相位板的检测系统的没计结果.详细讨论了计算全息图衍射级次的分离以及计算全息图的二元化,给出了振幅型的计算全息图的图样.计算全息图的刻线最小问隔是40μm,计算全息图的制作精度对检测结果的波前误差的影响仅仅为0.005λ.对检测系统作了详细的公差分析,结果表明所有调整公差对整个检测系统的影响和方根值为83.954 nm.     

EAST���Ӳ�������λ����У׼�����о�

介绍了EAST低杂波天线相位采集控制系统中两个主要部分的相位本底的校准技术。一是由相控多结波导阵天线与等离子体相切弧面引入的相位本底的静态校准,二是天线移动时软波导伸缩引起的可变相位本底的动态校准。低杂波天线相位本底校准技术为相位反馈控制系统提供了准确的相位基点,为实现预设相位与实调相位的一致性奠定了基础。     

一种实用的傅里叶变换轮廓术系统校准方法

在傅里叶变换轮廓术(FTP)中,根据针孔模型透镜成像理论,在考虑摄像机的径向畸变和切向畸变的情况下,利用畸变量较小的图像中心信息,对测量系统放置位置进行调整。采用相位——高度映射并结合最小二乘法及曲线拟合对高度和畸变分别校准。该方法能够简单、快速的对摄像机系统进行标定和修正,提高了FTP测量的精度,特别是在横向坐标方向上的精度。实验验证了所提方法的正确性。     

20 Hz~10 kHz光纤水听器相移灵敏度校准

利用相位生成载波解调技术精确测量光纤水听器的光相移量,在20 Hz~10 kHz频率范围实现了光纤水听器探头相移灵敏度的校准.20 Hz~1.25 kHz频段采用驻波管比较法进行校准,1.25 kHz~10 kHz频段采用自由场脉冲比较法进行校准.利用本文建立的校准系统,对TMD 35#光纤水听器的相移灵敏度进行校准,校准结果表明,两种方法测得的相移灵敏度具有很好的一致性,在1.25 kHz频率点的相移灵敏度值偏差为0.8 dB.不确定度分析表明,该校准系统的扩展不确定度(k=2)为0.9 dB.     

Windowed Fourier assisted two-dimensional Hilbert transform for fringes phase extraction

In this article, two-dimensional windowed Fourier assisted Hilbert transform for fringes phase extraction has been proposed. The mathematical derivations of the filtered fringes image and its Hilbert transformations are presented using windowed Fourier transform. The proposed method has been verified by calculating the wrapped and unwrapped phase of the experimental moire fringes. In comparison to the conventional fringes phase extraction methods, the proposed method is found to be effective.     

Innovative calibration technique for fringe projection based 3D scanner

A new approach to 3D scanners calibration, based on Fourier Transform Profilometry method, is proposed and verified by experiments. Commonly used calibration techniques require that a calibration plane is placed in different and known positions in the scanner measuring volume; an optimization procedure iteratively change the value of some calibration parameters in order to minimize the discrepancy between the height distributions of the measured planes and the reference ones. The main limit of this type of calibration techniques is the necessity to guarantee a high accuracy in the placement of the planes used as calibration references. The innovation of the method proposed in this paper is the complete removal of any device for the accurate plane placement by assigning the task of the plane positions estimation to the camera, which is part of the scanner. The well known camera calibration algorithm proposed by Zhang permits at the same time to calibrate the camera and to estimate the positions and orientations of the plane used for the calibration itself. The knowledge of the plane position allows to use them as a reference of the scanner calibration. The obtained results show that this method provides accuracy values for the scanner parameters estimation comparable with other calibration techniques, but the advantage is that no particular device is needed.     

Computer-Generated Holograms Based on the Three-Dimensional Fourier Spectrum

A method to synthesize a computer-generated hologram (CGH) of real-existing objects from projection images is proposed. Different from other similar methods, our method enables the synthesis of a CGH with only one-dimensional (1-D) mechanical scanning of the objects. Our method is connected with the three-dimensional (3-D) Fourier spectrum of the objects by the 3-D central slice theorem (CST). Two efficient recording techniques for projection images and numerical experiments to verify our principle is discussed. A comparison between the two techniques is also presented from the viewpoint of diffraction efficiency. © 2005 The Optical Society of Japan     

基于分数阶傅里叶变换的光学加密影片

随着通信与网络的快速发展,能够包含大容量信息的影片得到了广泛应用。利用分数阶傅里叶变换的特点,提出了一种全光学加密解密影片的方法。将现有的影片加密密钥从二重变为了四重,显著增加了影片的安全性。通过改变振幅型正弦光栅的作用位置,将影片的加密解密次数由现有的每帧各一次减小为总共一次,优化了算法。仿真结果验证了该方法的有效性。     

基于傅里叶频谱分析的相位测量轮廓术系统Gamma非线性校正方法

数字投影和成像系统的Gamma非线性效应是导致相位测量轮廓术（PMP）测量误差的重要原因。目前大多采用多帧条纹图进行Gamma校正,使测量的实时性受到限制。提出了一种Gamma校正方法,利用正交光栅像的傅里叶频谱分布计算Gamma值,再根据此Gamma值对投影相移条纹进行Gamma逆变换,实现投影条纹输入值的提前校正,以获取具有良好正弦性的结构条纹,从而降低PMP相位测量误差。校正过程中只需一帧条纹图,而且考虑了测量系统的离焦效应。实验证实了该方法的有效性和正确性。     

基于傅立叶变换的射频场分布测量方法

提出了一种基于傅立叶变换的射频场分布测量方法，该方法可以方便地测量出射频场的分布，其测量结果与样品的均匀度无关并且可以分别观测某个像素点处的层内射频场非均匀性或某个小区域内的射频场非均匀性.     

基于空域非均匀傅里叶变换的傅里叶望远镜

为了在稀疏发射阵列下清晰重构目标图像,提出了一种基于空域非均匀傅里叶变换(NDFT)的傅里叶望远镜信号处理方法。依据傅里叶望远镜的发射器位置与抽取的目标空间频率关系,结合MATLAB程序特点,完成了空域非均匀傅里叶逆变换,重构了目标图像。稀疏发射阵列配置方式为:T型阵列单臂放置11个发射望远镜,连续抽取目标的8个低频信息,再抽取3个高频分量。选择不同形状和灰度分布的4个卫星作为成像目标。与补零均匀快速傅里叶变换(FFT)方法重构的图像对比发现:信噪比为100 dB时,相比补零均匀FFT方法, NDFT方法重构图像的Strehl比都有所提升,最高提升了0.159 8。     

Accurate carrier-removal technique based on zero padding in Fourier transform method for carrier interferogram analysis

Based on interferogram zero padding and fast Fourier transform (FFT) methods, an effective, straightforward and stable carrier-removal approach in Fourier transform (FT) based method for carrier interferogram analysis is proposed. The spatial carrier interferogram is firstly extrapolated by zero padding method, and the carrier-frequency values within a small fraction of an integral (or a pixel) are estimated from the extrapolation interferogram with FFT method. Then the carrier-phase component is removed by subtracting a pure carrier-frequency phase constructed by the estimated carrier-frequencies in the spatial domain. Numerical simulations and experiments are given to demonstrate the performance of the proposed method and the results show that the proposed method is effective and stable for suppressing the carrier-removal error in the FT method for carrier interferogram analysis.     

Measurements of flame-front curvature based on Fourier transformation

An optimized image processing method for calculating the local curvature of two-dimensional digitized flame-front contours is proposed. This contour-smoothing method is based on Fourier transformation of the entire contour and is different from conventional methods in which a chosen number of neighbouring pixel points is locally fitted to an ad hoc smooth function along the contour on a point-by-point basis. The maximum curvature that can be measured with the proposed method is determined by the inner cut-off scale from a fractal length measure of the flame-front contour and is limited by image spatial resolution only. Curvature measurements are also made in highly stretched turbulent premixed methane–air jet flames. The measured probability density functions of local flame curvature are consistent with the generalized form of a symmetric Gaussian distribution suggested by Bradley et al. (Combustion and Flame, 135, 503–523 (2003)). Advantages and limitations of the proposed method are also discussed.     

基准光栅重构傅里叶变换轮廓术

应用傅里叶轮廓变换术进行三维形貌测量中,为了获得待测物体的高度相位信息,通常需要采集两幅图像.因此当光学系统发牛变动时,必须重新采集基准光栅图像,不利于快速测量.提出一种从变形光栅图像中获取基准光栅图像信息的测量方法.首先在变形光栅图像中记录基准光栅信息,然后通过傅里叶分析提取基准光栅频率信息,通过图像分析获得基准光栅相位信息,最后重构出一幅完整的基准光栅图像,实现三维物体形貌测量.实验结果验证了该方法的可行的.