Co与Cu掺杂ZnO薄膜的制备与光致发光研究

采用溶胶-凝胶旋涂法在玻璃衬底上制备了Co, Cu单掺杂及Co,Cu共掺杂ZnO薄膜.用金相显微镜观察了Co与Cu掺杂对ZnO薄膜形貌的影响.X射线衍射（XRD）研究揭示所有ZnO薄膜样品都存在（002）择优取向,在Cu单掺的ZnO薄膜中晶粒尺寸最大.对所有样品的室温光致发光测量都观察到较强的蓝光双峰发射和较弱的绿光发射,其中长波长的蓝光峰和绿光峰都能够通过掺杂进行控制.对不同掺杂源的ZnO薄膜发光性能进行了分析,认为蓝光峰来源于电子由导带底到锌空位能级的跃迁及锌填隙到价带顶的跃迁,绿光峰是由于掺杂造成的 关键词： ZnO薄膜 溶胶-凝胶 Co Cu掺杂 光致发光     

Fe,Co共掺杂ZnO薄膜结构及发光特性研究

采用溶胶凝胶法在玻璃衬底上制备了Fe,Co共掺Zn0.9FexCo0.1-xO(x=0,0.03,0.05,0.07)系列薄膜.通过扫描电镜(SEM)、X射线衍射(XRD)、X射线光电子谱(XPS)和光致发光(PL)谱对薄膜样品的表面形貌、晶体结构、成分和光学性能进行了研究.XRD结果表明所有ZnO薄膜样品都呈六方纤锌矿结构,在样品中没有观察到与Fe和Co相关的团簇,氧化物及其他杂相的衍射峰,表明共掺杂改善了Fe或Co在ZnO的分散性.XPS测试结果揭示样品中Co离子的价态为+2价;Fe离子的价态为+2价和+3价共存,但Fe相对浓度的增大导致Fe3+含量增加.所有样品的室温光致发光谱(PL)均观察到紫外发光峰和蓝光双峰,其中Fe,Co共掺ZnO薄膜的紫外发光峰较本征ZnO出现蓝移,蓝光双峰峰位没有变化,但发光强度有所减弱;而掺杂ZnO薄膜的绿光发光峰几乎消失.最后,结合微结构和成分分析对薄膜样品的发光机理进行了讨论.     

溶胶-凝胶法制备Li-N双掺p型ZnO薄膜的结构、光学和电学性能

采用溶胶-凝胶法在n型Si(100)衬底上沉积Li-N双掺杂ZnO薄膜,经X射线衍射和扫描电镜图片分析,所制备薄膜具有多晶纤锌矿结构和高的c轴择优取向.室温下霍尔效应测试结果显示Li-N双掺杂ZnO薄膜具有p型导电特性.在Li掺杂量为15.0at%,Li/N（摩尔比）为1∶1,700℃退火等优化条件下得到的最佳电学性能结果是：电阻率为0.34 Ω·cm,霍尔迁移率为16.43 cm²/V·s,载流子浓度为2.79×10¹⁹ cm^{-3关键词： Li-N双掺 p型ZnO薄膜 溶胶-凝胶 性能}     

Fe掺杂对溶胶凝胶法制备的ZnO: Ni薄膜结构及发光特性的影响

采用溶胶凝胶法在玻璃基片上制备了ZnO及Ni, Fe共掺杂的Zn_0.95-xNi_0.05Fe_xO (x=0, 0.005, 0.01, 0.03, 0.05) 薄膜. 通过扫描电镜(SEM) 和X射线衍射(XRD) 研究了薄膜样品的表面形貌和晶体结构. 结果表明所有样品都具有(002) 择优取向, Fe掺杂导致ZnO: Ni薄膜的晶体质量变差, 晶粒尺寸减小, 但适当的Fe掺杂有利于获得致密、 均匀的薄膜. XPS测试结果表明样品中Ni离子的价态为+2价, Fe离子的价态为+2价和+3价.室温光致发光(PL) 测量表明, 所有样品均观察到较强的紫外发光峰, 蓝光双峰和绿光发光峰. ZnO: Ni薄膜的发光强度可以通过Fe掺杂进行有效调节. 进而我们讨论了Ni, Fe共掺杂ZnO样品的发光机理.     

用电化学沉积方法制备钴掺杂的氧化锌薄膜及其光学性质

通过选用乌洛托品作为络合剂,采用电化学沉积的方法成功地制备出钴掺杂的氧化锌薄膜。通过对样品的XRD表征,得出生长的样品为ZnO纤锌矿结构,并没有其他杂相峰,即没有出现分相;通过对样品XPS的分析显示Co离子在薄膜中以+2价的形式存在;为进一步验证Co²⁺离子进入ZnO的晶格,对掺杂不同Co²⁺浓度的样品进行PL谱的测量,从发光光谱上可以看出随着掺杂Co²⁺浓度的增加,带隙逐渐变窄,发光峰位红移,证明Co²⁺部分取代了Zn²⁺而进入了ZnO晶格中。     

Na-Mg共掺杂ZnO薄膜的结构和光学性质

利用溶胶-凝胶法,在普通载玻片上使用旋转涂膜技术制备了具有c轴择优取向生长的Na-Mg共掺杂的ZnO薄膜。用XRD、SEM、光致发光(PL)及透射光谱对薄膜样品进行了表征。结果表明:Na-Mg共掺杂有利于ZnO薄膜的c轴择优取向生长,并且随着Na+掺杂浓度的增加,晶粒尺寸先增大后减小;通过比较不同掺杂浓度ZnO薄膜的PL谱,推测发光峰值位于380nm的紫外发射与ZnO的自由激子复合有关;发现掺入Mg的确能使ZnO禁带宽度增大,掺杂组分为Na0.04Mg0.2Zn0.76O时,其PL谱只有一个很强的紫光发射峰,其近带边紫外光发射强度较未掺杂的ZnO增强了近10倍,极大地提高了薄膜紫外发光性能;并且随Na+浓度增加薄膜透光性减弱。     

Co掺杂对ZnO薄膜结构和性能的影响

采用PVA溶胶-凝胶方法，在玻璃衬底上制备了Zn_1-xCo_xO薄膜，利用X射线衍射仪(XRD)研究了不同Co含量对其微结构的影响.采用振动样品磁强计(VSM)测量了Zn_0.88Co_0.12O样品室温下的磁性.采用荧光光谱仪研究了Zn_1-xCo_xO样品室温下的发光特性，分析掺杂含量对其发光性能的影响，发现随着掺杂含量的增加，蓝光发光峰有一定的红移现象. 关键词： PVA方法 ZnO 掺杂     

退火温度对Cu:ZnO薄膜绿光发射的影响

利用溶胶-凝胶法在Si衬底上制备了不同退火温度的Cu:ZnO薄膜.利用X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜和光致发光谱研究了样品的晶格结构、表面形貌、成分及其发光特性.结果表明:所有样品均具有高度的c轴择优取向,随着退火温度的升高,样品的结晶质量变好,样品的表面都被晶粒覆盖,强而稳定的绿光发射被观察到.绿光强度随退火温度的升高先增加后减小,发光中心位置不随退火温度的变化而改变,这样的绿光发射强而稳定.XRD和XPS结果表明,随退火温度的升高Cu2+还原为Cu+,导致Cu:ZnO薄膜形成的缺陷是VZn,所以绿光发射是由VZn引起的.Cu2+还原为Cu+时,Cu:ZnO薄膜中VZn浓度增加,使绿光发射强度增大.当退火温度超过800?C时,Cu2+的还原能力变差,绿光发射强度减弱.     

In掺杂ZnO薄膜的制备及其白光发射机理

采用溶胶-凝胶法在Si衬底上制备了本征ZnO薄膜和In:(Zn+In)分别为5%,8%,10%的ZnO薄膜,对薄膜的晶相结构和光电性质进行了表征并在CIE-XYZ表色系统中计算了不同样品的色品坐标.结果表明:In掺入后ZnO薄膜的择优生长方向由(002)面变为(101)面且面间距变小,当In掺杂量为5%时,In原子完全替代Zn原子;薄膜的电阻率随In含量的增加出现先抑后扬的趋势;随着In的掺入光谱的紫外发射峰红移,并在670 nm左右出现一个新的峰值;In:(Zn+In)为5%样品具有白光发射特性.从第一 关键词： In掺杂ZnO薄膜 溶胶-凝胶 色品坐标 白光发射     

采用PVA方法制备ZnO基发光稀磁半导体

不同的制备工艺对ZnO薄膜的微结构和性能有很大的影响,为了得到成本较低,样品具有较好特性的实验方法,对于制备手段进行了探索。使用PVA溶胶-凝胶法制备了Zn_0.88Co_0.12O薄膜,研究了不同退火工艺对其微结构的影响。对于Zn_0.88Co_0.12O样品的微结构和室温下的铁磁性和发光特性,具体比较分析了产生原因。对比了Co掺杂和复合Co、Fe掺杂Zn_0.88(Co_0.5Fe_0.5)_0.12O样品的微结构,采用振动样品磁强计(VSM)测量了样品的磁特性,发现单一掺杂的薄膜具有更好的晶体质量和更强的磁性。     

Crystalline structure and morphological properties of undoped and Sn doped ZnO thin films

Undoped and tin (Sn) doped ZnO thin films have been prepared by spray pyrolysis method. Effect of Sn dopant on the crystalline structure and morphological properties of ZnO thin films has been investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) method. XRD patterns confirm that the films have polycrystalline nature. While undoped ZnO film has (101) as the preferred orientation, Sn doped ZnO thin films have (002) as the preferred orientation. Grain sizes, lattice parameters and texture coefficient values of the films were determined. Microstructure was analyzed by SEM and the influence of the doping concentration in the microstructure of the films is investigated.     

过渡金属与F共掺杂ZnO薄膜结构及磁、光特性

采用溶胶-凝胶法在玻璃衬底上制备了过渡金属元素与F共掺杂Zn_0.98-xTM_xF_0.02O (TM_x=Cu_0.02, Ni_0.01, Mn_0.05, Fe_0.02, Co_0.05)薄膜, 进而利用X射线衍射仪、扫描电子显微镜、紫外-可见透过谱、光致发光及振动样品磁强计等研究了薄膜的表面形貌、微结构、禁带宽度及光致发光(PL)和室温磁学特性. 研究表明: 掺杂离子都以替位的方式进入了ZnO晶格, 掺杂不会破坏ZnO的纤锌矿结构. 其中Zn_0.93Co_0.05F_0.02O薄膜样品的颗粒尺寸最大, 薄膜的结晶度最好且c轴择优取向明显; Zn_0.93Mn_0.05F_0.02O薄膜样品的颗粒尺寸最小, 薄膜结晶度最差且无明显的c轴择优取; Cu, Ni, Fe与F共掺杂样品的颗粒尺寸大小几乎相同. TM掺杂样品均表现出很高的透过率, 同时掺杂后的薄膜样品的禁带宽度都有不同程度的红移. PL谱观察到Zn_0.98-xTM_xF_0.02O薄膜的发射峰主要由较强的紫外发射峰和较弱的蓝光发射峰组成. Zn_0.93Mn_0.05F_0.02O薄膜样品的紫外发光峰最弱, 蓝光发射最强, 饱和磁化强度最大; 与之相反的是Zn_0.96Cu_0.02F_0.02O薄膜, 其紫外发光峰最强, 蓝光发射最弱, 饱和磁化强度最小. 结合微结构和光学性质对Zn_0.98-xTM_xF_0.02O薄膜的磁学性质进行了讨论.     

Optoelectronics and formaldehyde sensing properties of tin-doped ZnO thin films

Sn-doped ZnO thin films were deposited on clean glass substrates using the chemical spray pyrolysis technique. XRD analyses confirm stable ZnO hexagonal wurtzite structure of the films with crystallite size in the range of 20–28 nm. The surface roughness of the films increases on Sn doping, which favors to higher adsorption of oxygen species on the film surface, resulting in higher gas response. Optical studies reveal that the band gap decreases on Sn doping. All the films show near band edge emission, and on Sn doping the luminescence peak intensity has been found to increase. Photocurrent in the 1.5 at.% doped film enhances about three times to that observed in the undoped ZnO film. Among all the films examined, the 1.5 at.% Sn-doped film exhibits the maximum response (～94.5 %) at the operating temperature of 275?°C for 100 ppm concentration of formaldehyde, which is much higher than the response (～35 %) in the undoped film. The gas response of the film is attributed to the chemisorption of oxygen on the film surface and the subsequent reaction between the adsorbed oxygen species and the formaldehyde molecules.     

A comparative study of the microstructures and optical properties of Cu- and Ag-doped ZnO thin films

Cu- and Ag-doped ZnO films were deposited by direct current co-reactive magnetron sputtering technique. The microstructure, the chemical states of the oxygen, zinc, copper and silver and the optical properties in doped ZnO films were investigated by X-ray diffraction spectroscopy (XRD), X-ray photoelectron spectroscopy (XPS) and UV-Visible spectroscopy. XRD analysis revealed that both of Cu- and Ag-doped ZnO films consist of single phase ZnO with zincite structure while the doping elements had an evident effect on the (0 0 2) preferential orientation. The XPS spectra showed that the chemical states of oxygen were different in Cu- and Ag-doped ZnO thin films, which may lead to the shift of the band gap as can be observed in the transmittance and absorption spectra. Meanwhile, the widths of band tails of ZnO films became larger after Cu and Ag doping.     

Effect of doping concentration on the structural and optical properties of pure and tin doped zinc oxide thin films by nebulizer spray pyrolysis (NSP) technique

Pure and tin doped zinc oxide (Sn:ZnO) thin films were prepared for the first time by NSP technique using aqueous solutions of zinc acetate dehydrate, tin (IV) chloride fendahydrate and methanol. X-ray diffraction patterns confirm that the films are polycrystalline in nature exhibiting hexagonal wurtzite type, with (0 0 2) as preferred orientation. The structural parameters such as lattice constant (‘a’ and ‘c’), crystallite size, dislocation density, micro strain, stress and texture coefficient were calculated from X-ray diffraction studies. Surface morphology was found to be modified with increasing Sn doping concentration. The ZnO films have high transmittance 85% in the visible region, and the transmittance is found to be decreased with the increase of Sn doping concentration. The corresponding optical band gap decreases from 3.25 to 3.08 eV. Room temperature photoluminescence reveals the sharp emission of strong UV peak at 400 nm (3.10 eV) and a strong sharp green luminescence at 528 nm (2.34 eV) in the Sn doped ZnO films. The electrical resistivity is found to be 10⁶ Ω-cm at higher temperature and 10⁵ Ω-cm at lower temperature.     

Property enhancement of transparent conducting zinc oxide thin films—Effect of simultaneous (Sn+F) doping

Undoped and simultaneously (Sn+F) doped ZnO thin films were fabricated using a simplified spray pyrolysis technique and the effects of Sn doping level on their electrical, structural, optical and surface morphological properties were studied. The XRD patterns confirmed the hexagonal wurtzite structure of ZnO. The minimum electrical resistivity of 0.45×10⁻² Ω cm was obtained for ZnO films having Sn+F doping levels of 8+20 at%. All the films exhibited average optical transmittance of 85% in the visible region, suitable for transparent electrode applications. The overall quality of the fabricated films was confirmed from photoluminescence (PL) studies. The PL and surface morphological studies along with the elemental analysis showed the increase of Sn diffusion into the ZnO lattice which was consistent with the concentration of Sn in the starting solution. The results of the analysis of physical properties of simultaneously doped ZnO films proved that these films might be considered as promising candidates for solar cells and other opto-electronic applications.     

Influence of Concentration of Vanadium in Zinc Oxide on Structural and Optical Properties with Lower Concentration

ZnO films doped with different vanadium concentrations are deposited onto glass substrates by dc reactive magnetron sputtering using a zinc target doped with vanadium. The vanadium concentrations are examined by energy dispersive spectroscopy （EDS） and the charge state of vanadium in ZnO thin films is characterized by x-ray photoelectron spectroscopy. The results of x-ray diffraction （XRD） show that all the films have a wurtzite structure and grow mainly in the c-axis orientation. The grain size and residual stress in the deposited films are estimated by fitting the XRD results. The optical properties of the films are studied by measuring the transmittance. The optical constants （refractive index and extinction coefficient） and the film thickness are obtained by fitting the transmittance. All the results are discussed in relation with the doping of the vanadium.