首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到17条相似文献,搜索用时 109 毫秒
1.
报道了一个低阈值宽调谐、被动调Q、单谐振掺MgO的周期性极化铌酸锂晶体(PPMgLN)光学参量振荡器。利用被动调Q的Nd:YVO4激光器作为泵浦源,采用外腔结构,在室温下,实现了PPMgLN晶体的准相位匹配光学参量振荡。光参量振荡的阈值仅为0.27W(单脉冲能量4.5μJ、脉宽35ns);在泵浦光为1.35W(脉冲能量8.2μJ、脉宽35ns),PPMgLN周期为31μm时,获得了161.9mW,3.202μm脉冲激光输出;同时获得了98.5mW的1.594μm信号光输出,总的光光转化效率达到19.3%。通过改变晶体的周期,实现了闲频光3.13~4.19μm,信号光1.43~1.65μm的宽带可调谐激光输出。  相似文献   

2.
利用半导体激光泵浦输出1064 nm波长的全固态连续Nd:YVO4激光器作为泵浦源,采用周期调谐和温度调谐组合调谐技术,对基于掺氧化镁周期性极化铌酸锂晶体(MgO:LiNbO3, PPMgLN)准相位匹配(QPM)的全固态连续波(CW)光学参量振荡器(OPO)宽波段无分立连续调谐输出特性进行研究。实验采用连续工作模式和外腔结构,基于多周期PPMgLN晶体的30.2,30.4和30.6 m周期,在改变晶体的极化周期的基础上,同时在30~100 ℃范围内调节晶体工作温度。实验结果表明:CW PPMgLN OPO的泵浦阈值仅为0.22 W;不同极化周期需要的温度调谐范围不同;信号光在1 559.8~1 597.2 nm近红外波段和闲频光在3 187.3~3 347.3 nm中红外波段连续调谐输出。实现了外腔式全固态CW OPO在信号光和闲频光波段的无分立连续调谐输出。  相似文献   

3.
基于畴背向反转效应,利用外加短脉冲极化电场,通过对脉冲宽度、脉冲间隔以及脉冲个数的有效控制,在掺5mol%镁的铌酸锂晶体上得到周期为1.7μm的均匀亚微米畴结构,其纵向深度为30—50μm.同时,使用脉冲宽度为100ms的宽脉冲信号得到了畴带宽度仅为0.5μm的非对称微畴结构对亚微米畴结构产生的微观机制和物理过程进行了初步探讨. 关键词: 背向反转效应 掺镁铌酸锂晶体 周期极化  相似文献   

4.
周期极化铌酸锂晶体的红外光谱测量分析   总被引:1,自引:0,他引:1  
对周期极化非线性品体的光参量振荡器实现连续调谐输出的条件进行了理论模拟和分析,并且针对基于多周期的掺镁铌酸锂晶体光参量振荡器进行了实验研究,在掺镁铌酸锂晶体内制作了6个等间隔的晶畴区,其间距为0.5 μm,极化周期范围为29.0~31.5 μm.在室温下采用LD端面抽运的声光调Q Nd:YVO4激光器作泵浦源,实现了PPMgLN光参量振荡器的信号光在1449.7~1665.0 nm、闲频光在3 989.2~2 946.0 nm范围内的调谐输出,其最低激射阈值为108.0 mW、最高激射阈值为149.2 mW.当泵浦功率为649 mW时,获得了信号光最高为118.5 mW的输出,其光-光转换效率为18.26%;闲频光最高输出为46.6 mW,其光一光转换效率为7.18%.以上参数均接近实用化水平.而且,这两个波段的光源分别在整个光纤通信的S+C+L波段和大气层透射窗口范围,具有十分重要的应用前景.  相似文献   

5.
基于掺MgO周期极化铌酸锂晶体的光学参量振荡器是一种全固态中红外可调谐相干光源.泵浦源为1064 nm声光调Q Nd:YAG激光器.通过温度调谐实现了中红外可调谐参量光的输出,当晶体的温度从40°C升高到200°C时,获得信号光的输出范围为1.561 μm~1.670μm,空闲光的调谐范围为3.342 μm~2.932 μm.当泵浦源脉宽为70 ns,重复频率为10 kHz,平均功率为.161 W,获得波长为1631μm.当泵浦源脉宽为70 ns,重复频率为10 kHz,平均功率为1.61 W,获得波长为1631 nm信号光的输出功率为21 1 mW.  相似文献   

6.
对基于周期极化掺镁铌酸锂晶体的信号光单谐振光学参量振荡器的输出特性进行了实验研究.讨论了光学参量振荡器谐振腔的腔长、周期极化铌酸锂晶体的通光长度、输出镜的透过率以及抽运光的脉冲宽度对光学参量振荡器谐振阈值的影响.光学参量振荡器的抽运源采用输出波长为1 064 nm的声光调Q Nd∶YVO4激光器,在重复频率为2 kHz、周期极化掺镁铌酸锂晶体的温度为30 ℃的条件下,光学参量振荡器的振荡阈值仅为48 mW.当抽运功率为94 mW时获得了25 mW的信号光输出,其光-光转换效率为26.6%.  相似文献   

7.
对基于周期极化掺镬铌酸锂晶体的信号光单谐振光学参量振荡器的输出特性进行了实验研究.讨论了光学参量振荡器谐振腔的腔长、周期极化铌酸锂晶体的通光长度、输出镜的透过率以及抽运光的脉冲宽度对光学参量振荡器谐振阈值的影响.光学参量振荡器的抽运源采用输出波长为1 064 nm的声光调Q Nd:YVO_4激光器,在重复频率为2 kHz、周期极化掺镁铌酸锂晶体的温度为30℃的条件下,光学参量振荡器的振荡阈值仅为48 mW.当抽运功率为94 mW时获得了25 mW的信号光输出,其光-光转换效率为26.6%.  相似文献   

8.
利用掺杂浓度为5 mol%的掺氧化镁多周期极化铌酸锂晶体实现了高效单谐振的准相位匹配光参量振荡器,所使用的周期极化铌酸锂晶体有6个周期,且以1 μm为间隔,从26.5~31.5 μm. 该光参量振荡器以脉宽为150 ns,重复频率为10 kHz的声光调Q Nd∶YAG激光器为泵浦源,且泵浦光波长为1.064 μm. 通过控制晶体的温度(50~200℃)以及改变晶体的极化周期(26.5~31.5 μm),可由该光参量振荡器获得2.83~2.89 μm,3.10~3.38 μm,3.57~3.78 μm,3.95~4.12 μm, 4.28~4.46 μm,4.65~4.79 μm的闲频光连续调谐输出. 且当泵浦功率为8.15 W时,在闲频光输出波长为3.33 μm处,获得了最大输出功率2.17 W.  相似文献   

9.
闫卫国  陈云琳  王栋栋  郭娟  张光寅 《物理学报》2006,55(11):5855-5858
研究了掺镁铌酸锂(MgO:LiNbO3)的极化特性及其畴壁运动的性质,通过调节多个脉冲外加电场来控制畴壁的运动,在背向反转效应作用下,反转畴发生劈裂,制备出均匀的掺镁铌酸锂亚微米周期畴结构,并分析探讨了掺镁铌酸锂亚微米结构的成因及其反转机理. 关键词: 亚微米畴结构 掺镁铌酸锂 背向反转  相似文献   

10.
研究了温度调谐下周期极化镁掺杂铌酸锂晶体的红外光参量振荡特性。采用外电场短脉冲极化技术,在大小为7.0mm×50.0mm×1.0mm的Z切高镁掺杂(摩尔分数0.05)铌酸锂上制备出了准相位匹配光学微结构器件,极化周期为30.0μm。以输出波长为1064nm的声光调QNd:YAG固体激光器作为基频泵浦光开展了光参量振荡研究。实验表明:泵浦该PPMgLN晶体,实现了室温下低阈值红外光参量振荡产生,阈值功率仅为45mW(重复频率1kHz)。在泵浦输入功率为225mW时,有36mW信号光输出,转换效率达到16.0%,通过调谐晶体温度(20~180℃),获得了调谐范围为1503~1550nm波段的OPO信号光,实现了低阈值可调谐红外光的稳定输出。  相似文献   

11.
We report a narrow pulse width optical parametric oscillator based on periodically poled MgO:LiNbO3 (PPMgLN) with a high repetition rate under quasi-phase matched conditions. When the maximum pumping power of the 1,064-nm laser was 14.57 W, the acousto-optical (A-O) Q-switch repetition rate was 100 kHz, and the PPMgLN crystal grating period was 29.5 μm. A 1,474-nm signal light output power of 4.21 W and a 3,828 nm idler light output power of 1.547 W were obtained, corresponding to a pulse width of 9.52 ns and 9.65 ns, respectively. The overall optical–optical conversion efficiency was 39.5%. Additionally, by changing the temperature from 25°C to 150°C, a tunable signal wavelength of 1,474–1,499 nm and idler wavelength at 3,676–3,828 nm of the output laser were achieved.  相似文献   

12.
We present a cascaded continuous-wave singly resonant optical parametric oscillator (SRO) delivering idler output in mid-IR and terahertz frequency range. The SRO was pumped by an ytterbium-doped fiber laser with 27 W linear polarization pump powers, and based on periodically poled MgO:LiNbO3 crystal (PPMgLN) in two-mirror linear cavity. The PPMgLN is 50 mm long with 29.5 μm period. The idler power output at 3811 nm was obtained 2.6 W. The additional spectral components that have been attributed to cascaded optical parametric processes are described at increasing pump levels. Besides the initial signal component at about 1476.8 nm, further generated wavelengths with frequency shifts about 47 cm?1, 94 cm?1 and 104 cm?1 were observed. It was speculated that the idler waves lie in the terahertz (THz) domain from the observed results.  相似文献   

13.
Shuyan Diao 《Laser Physics》2012,22(12):1793-1796
The experimental results of a high efficiency infrared laser are demonstrated on a quasi phase matched optical parametric generator in PPMgLN (5% MgO doping) pumped by a 1064 nm Nd:YAG laser. A broad continuous signal spectrum 1.56?C1.67 ??m are obtained by tuning the crystal temperature from 20°C to 200°C. When the average pump power is 1.82 W with about 70 ns pulse duration operating at a repetition rate of 10 kHz, the maximum total output power of the PPMgLN OPG is about 323.58 mW consisting of 210 mW of 1.639 ??m signal radiation and 113.58 mW of 3.02 ??m idler radiation.  相似文献   

14.
We report a continuous-wave (CW) mid-infrared singly resonant optical parametric oscillator (SRO) based on periodically poled MgO-doped LiNbO3 (PPMgLN) pumped by a high power, single frequency fiber laser in master oscillator-power amplifier (MOPA) configuration at 1.064 μm. Using four-mirror ring OPO cavities, at the PPMgLN’s grating period of 30.5 μm and the temperature of 23°C, we achieved the maximum idler output power of 7.2 W at 3.4 μm when the pump power was 52.8 W. The total power-conversion efficiency from the pump to the idler in this experiment is about 13.6%, and corresponds to ∼44% of quantum-limited performance.  相似文献   

15.
We report a continuous-wave singly resonant optical parametric oscillator (SRO) with more than 12 W of idler power at 3414 nm when it was operated at 30°C. The SRO was directly pumped by a single-frequency, ytterbium-doped fiber laser with 49 W linear polarization pump powers, and based on 50 mm long periodically poled MgO:LiNbO3 crystal (PPMgLN) in two-mirror linear cavity with 30.5 μm grating period. It’s pump power at threshold was 5.4 W. The slope-efficiency and quantum-limited performance reached 26 and 79.2%, respectively. The beam polarization matched the ee + e interaction in crystal. The idler waves were temperature tuned in the range of 3654 to 3811 nm and 3248 to 3414 nm based on two 50 mm long PPMgLN with 29.5 and 30.5 μm grating period. To the best of our knowledge, this is the highest continuouswave mid-IR output obtained for a fiber laser pumped optical parametric oscillator (OPO).  相似文献   

16.
We obtain a continuous-wave (CW) Nd:YVO4/PPMgLN intracavity singly resonant optical parametric oscillator (ISRO). The threshold value of the CW-ISRO system is only 2.8 W at 808 nm. When the pump power is 5.5 W, an idle laser output power of 410 mW, and a signal laser output power of 345 mW have been achieved. By changing the grating periods of the domain structure on the PPMgLN wafer, we enable a wide-tunable mid-infrared spectrum of 2.95–4.16 μm and near-infrared spectrum of 1.43–1.66 μm.  相似文献   

17.
A high repetition rate mid-infrared singly resonant optical parametric oscillator (OPO) using MgO-doped multi-grating periodically poled LiNbO3 (MgO:PPLN) is demonstrated. A 1064 nm Q-switched Nd:YVO4 laser at 10 kHz repetition rate and pulse width of 17.8 ns was used to pump the OPO. The period of the quasi-phase matched (QPM) grating in the multi-grating MgO:PPLN chip varied from 25.5 to 31.5 μm in steps of 0.5 μm. This corresponds to the generation of a signal beam from 1.37 to 1.64 μm and an idler beam from 3.0 to 4.8 μm, respectively. A maximum signal power of 250 mW and idler power of 140 mW has been obtained with an input pump beam of power 1.92 W, for a grating period of 30.5 μm. A maximum optic-optic conversion efficiency of 20% and 7.4% in the idler has been observed. It has been observed that the output power increases as the period of the grating increases.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号