Measurements of the temperature and water vapor concentration in a hot zone by tunable diode laser absorption spectrometry

A tunable diode laser absorption spectroscopy (TDLAS) technique and appropriate instrumentation was developed for the measurement of temperature and water vapor concentrations in heated gases. The technique is based on the detection of the spectra of H₂O absorption lines with different energies of low levels. The following absorption lines of H₂O were used: 7189.344 cm⁻¹ (E″=142 cm⁻¹), 7189.541 cm⁻¹ (E″=1255 cm⁻¹), 7189.715 cm⁻¹ (E″=2005 cm⁻¹). Spectra were recorded using fast frequency scanning of a single distributed feedback (DFB) laser. A unique differential scheme for the recording of the absorption spectra was developed. An optimal technique for fitting the experimental spectra was developed.     

Wavelength modulation and cavity enhanced absorption spectroscopy using ～1.9?μm radiation produced by difference frequency generation with a MgO doped PPLN crystal

We have demonstrated the production of ∼1.9 μm near-infrared radiation by using difference frequency generation within a 5% MgO doped PPLN crystal by coupling ∼735 nm radiation from a tunable external cavity diode laser with relatively high powered 532 nm radiation from both Nd:YVO₃ and Nd:YAG lasers. The radiation produced is of low power, ∼15 μW, and was used in conjunction with the sensitivity enhancing techniques of wavelength modulation spectroscopy (WMS) and cavity enhanced absorption spectroscopy (CEAS). Experiments were carried out on rotationally resolved transitions in the combination bands of NH₃ and CO₂ in the 1.9 μm region. An α _min value of 3.6×10⁻⁶ cm⁻¹ Hz^−1/2 was achieved for WMS measurements on CO₂. A comparable α _min value of 2.2×10⁻⁶ cm⁻¹ Hz^−1/2 was achieved for NH₃ using CEAS. The low NIR power indicates that despite the level of MgO doping quoted for the crystal, under prolonged exposure photorefractive damage has occurred.     

An off-axis cavity-enhanced absorption spectrometer at 1605 nm for the 12CO2/13CO2 measurement

A distributed feedback diode laser sensor based upon off-axis cavity-enhanced absorption spectroscopy at 1605.5 nm has been developed for ¹³C¹⁶O₂/¹²C¹⁶O₂ isotope ratio measurements in synthetic air and human breath. A noise-equivalent absorption sensitivity of 3.9×10^-10 cm^-1 Hz^-1/2 has been determined for a cavity base length of 28.2 cm and averaging 4000 scans within 8.688 s. For 5% CO₂ concentration measurements, δ¹³C standard deviations of 1.8 ‰ and 3.7 ‰ have been estimated for five successive measurements based on peak height and integrated area estimations at 107.9 Torr, respectively. The contributions of amplified spontaneous emission of the laser and a radiation that is spatially uncoupled into the cavity mode have been described for cavity transmittance measurements. The limitations of the developed sensor and further steps towards precision and accuracy improvements are discussed. PACS 42.55.Px; 39.30.+w; 42.62.Fi; 42.60.-v     

Continuous wave,distributed feedback diode laser based sensor for trace-gas detection of ethane

The development of a continuous wave (CW), thermoelectrically cooled (TEC), distributed feedback (DFB) laser diode based spectroscopic trace-gas sensor for ultra-sensitive and selective ethane (C₂H₆) concentration measurements is reported. The sensor platform used tunable diode laser absorption spectroscopy (TDLAS) based on a 2f wavelength modulation (WM) detection technique. TDLAS was performed with a 100 m optical path length astigmatic Herriott cell. For an interference free C₂H₆ absorption line located at 2976.8 cm⁻¹ a 1σ minimum detection limit of 240 pptv (part per trillion by volume) with a 1 second lock-in amplifier time constant was achieved. In addition, reliable and long-term sensor performance was obtained when operating the sensor in an absorption line locked mode.     

Flexible laser diode trace gas sensor based on cavity ringdown spectroscopy with an optical fiber-coupled high-finesse external-cavity diode laser

A flexible and portable trace nitrogen dioxide sensor based on cavity ringdown spectroscopy using an optical fiber-coupled high-finesse cavity was successfully demonstrated. Tailoring the spatial mode matching condition of the core of an optical fiber and high-finesse external cavity allows for effective optical feedback into an antireflection-coated laser diode for stable resonant enhancement of the external cavity. The external cavity, which works as a ringdown cavity, could be remotely located from the light source and receiver section by only a single mode optical fiber. The sensitivity was found to be 1.0×10⁻⁷ cm⁻¹ in a compact 1-cm³ ringdown cavity volume.     

Line strength and collisional broadening studies of hydrogen sulphide in the 1.58 μm region using diode laser spectroscopy

High resolution diode laser spectroscopy has been applied to the detection of hydrogen sulphide at ppm levels utilizing different transitions within the region of the ν ₁+ν ₂+ν ₃ and 2ν ₁+ν ₂ combination bands around 1.58 μm. Suitable lines in this spectral region have been identified, and absolute absorption cross sections have been determined through single-pass absorption spectroscopy and confirmed in the Doppler linewidth regime using cavity enhanced absorption spectroscopy (CEAS). The desire for a sensitive system potentially applicable to H₂S sensing at atmospheric pressure has led to an investigation on suitable transitions using wavelength modulation spectroscopy (WMS). The set-up sensitivity has been calculated as 1.73×10⁻⁸ cm⁻¹ s^1/2, and probing the strongest line at 1576.29 nm a minimum detectable concentration of 700 ppb under atmospheric conditions has been achieved. Furthermore, pressure broadening coefficients for a variety of buffer gasses have been measured and correlated to the intermolecular potentials governing the collision process; the H₂S–H₂S dimer well depth is estimated to be 7.06±0.09 kJ mol⁻¹.     

A diode laser spectrometer for symmetry selective detection of ozone isotopomers

A tunable diode laser absorption spectrometer operating in the 10 μm range is described, which for the first time permits simultaneous detection and quantification of the five naturally most abundant ozone isotopomers: ¹⁶O₃, ¹⁶O¹⁶O¹⁸O, ¹⁶O¹⁸O¹⁶O, ¹⁶O¹⁶O¹⁷O, and ¹⁶O¹⁷O¹⁶O. Ozone samples of 25 μmole size are analysed with an estimated accuracy of 6‰ (2σ). This level of accuracy is demonstrated by comparing spectroscopically determined isotopologue enrichments of ¹⁶O₂ ¹⁷O and ¹⁶O₂ ¹⁸O with mass spectrometer measurements. Samples for the comparison were generated from natural oxygen in an electric discharge under two different pressure conditions. The precision obtained is sufficient to study both the isotopic and the symmetry dependence of the unique oxygen isotope anomaly in ozone formation, which shows isotopomer specific fractionation values well in the 10% range. PACS 42.60.By; 42.55.Px; 33.20.Ea     

Optical and IR study of Li2O–CuO–P2O5 glasses

Infrared (IR) and UV spectra of ternary Li₂O–CuO–P₂O₅ glasses in two series Li₂O(65−X)%–CuO(X%)–P₂O₅(35%), X = 20, 30, 40 and Li₂O(55−X)%–CuO(X%)–P₂O₅(45%), X = (10, 20, 30) were studied. Infrared (IR) investigations showed the metaphosphate and pyrophosphate structures and with increase of CuO content in metaphosphate glass, the skeleton of metaphosphate chains is gradually broken into short phosphate groups such as pyrophosphate. IR spectra showed one band at about 1,220 and 1,260 cm⁻¹ for P₂O₅(35%) and P₂O₅(45%) series, respectively, assigned to P=O bonds. For CuO additions ≤20 mol%, the glasses exhibit two bands in the frequency range 780–720 cm⁻¹ which are attributed to the presence of two P–O–P bridges in metaphosphate chain. But for CuO addition ≥30 mol%, the glasses exhibit only a single band at 760 cm⁻¹ which is assigned to the P–O–P linkage in pyrophosphate group. In optical investigations, absorption coefficient versus photon energy showed three regions: low energy side, Urbach absorption, and high energy side. In Urbach’s region, absorption coefficient depends exponentially on the photon energy. At high energy region, optical gap was calculated and investigations showed indirect transition in compounds and decreases in optical gap with increases of copper oxides contents that is because of electronic transitions and increasing of nonbridging oxygen content.     

Spectroscopic properties of 1.8 μm emission of thulium ions in germanate glass

A new type host of germanate glass (GeO₂− BaO−BaF₂−Ga₂O₃−La₂O₃) codoped with Tm₂O₃ has been investigated for application as laser material. It possesses a large emission cross section with the value of 9.3×10⁻²¹ cm² at 1.8 μm. Judd-Ofelt intensity parameters and radiative transition probability are calculated and analyzed by Judd-Ofelt theory and absorption spectra. The infrared emission spectra at 1.8 μm have been obtained by using a 794 nm laser diode as excitation resource. The emission intensity ratio of 1.8 (³F₄→³H₆) to 1.47 μm (³H₄→³F₄) increases, while the experimental lifetime of the Tm³⁺:³H₄ level decreases by increasing Tm₂O₃ concentration, which is attributed to the presence of a cross relaxation process. The most intensive emission at 1.8 μm is achieved from the germanate glass with the concentration of Tm₂O₃ reaches 1.0 wt%. The extended overlap integral method is used to calculate the microparameter of the energy transfer and the critical distance, which are derived to better understand the energy transfer process of thulium ions in the germanate glass responsible for emission at 1.8 μm.     

Low temperature cavity ring down spectroscopy with off-axis alignment: application to the A- and γ-bands of O2 in the visible at 90 K

The cavity ring down (CRD) technique presented here involves an optical cavity attached to a cryostat. The static cell and mirrors of the optical cavity are all inside a vacuum chamber at the same temperature of the cryostat. The temperature of the cell can be changed between 77 K and 298 K. An off-axis alignment of the laser beam into the cavity is used to increase the number of resonant modes inside the cavity and improve the signal to noise ratio of the absorption bands. To demonstrate the capabilities of the low temperature CRD cell, the absorption spectra of O₂ are recorded at 90 K for the A (υ′=0←υ″=0) and γ (υ′=2←υ″=0) bands of the b¹?_g ⁺? X³?_g ^-b^{1}\sum_{g}^{ +}\leftarrow X^{3}\sum_{g}^{ -} transition using cavity ring down spectroscopy. The optical cavity performance was tested using two variations of the CRD technique. The A-band is measured using the phase-shift cavity ring down method and the γ-band using the pulsed-laser exponential-decay method. A comparison between experimental and simulated spectra of the O₂ bands at 90 K confirms the molecular temperature measured by a sensor localized in the cell. Quantitative measurements of the individual rotational line intensities are made for the oxygen γ-band to confirm the temperature of the cell and calculate the vibrational band intensity. The application of this technique for laboratory studies of planetary atmospheres and the spectroscopy of molecular complexes is emphasized.     

Infrared diode laser spectroscopy

Three types of lasers (double-heterostructure 66 K InAsSb/InAsSbP laser diode, room temperature, multi quantum wells with distributed feedback (MQW with DFB) (GaInAsSb/AlGaAsSb based) diode laser and vertical cavity surface emitting lasers (VCSELs) (GaSb based) have been characterized using Fourier transform emission spectroscopy and compared. The photoacoustic technique was employed to determine the detection limit of formaldehyde (less than 1 ppmV) for the strongest absorption line of the v₃ + v₅ band in the emission region of the GaInAsSb/AlGaAsSb diode laser. The detection limit (less than 10 ppbV) of formaldehyde was achieved in the 2820 cm⁻¹ spectral range in case of InAsSb/InAsSbP laser (fundamental bands of v₁, v₅). Laser sensitive detection (laser absorption together with high resolution Fourier transform infrared technique including direct laser linewidth measurement, infrared photoacoustic detection of neutral molecules (methane, form-aldehyde) is discussed.     

Laser-based measurements of line strength, self- and pressure-broadening coefficients of the H35Cl R(3) absorption line in the first overtone region for pressures up to 1 MPa

A high-resolution spectrometer based on a vertical-cavity surface-emitting laser (VCSEL) was developed and used to determine the line strength S(T ₀)=12.53(11)×10⁻²¹ cm⁻¹/(molec cm⁻²) and the self-broadening coefficient g⁰_HCl=0.021787(61)\gamma^{0}_{\mathrm{HCl}}=0.021787(61)  cm⁻¹/atm of the R(3) absorption line in the first rovibrational overtone (2←0) band of H³⁵Cl. Furthermore, the first laser-based high-pressure study on the pressure broadening of HCl by He, N₂ and O₂(g⁰_N2=0.07292(5)\mathrm{O}_{2}(\gamma^{0}_{\mathrm{N}_{2}}=0.07292(5)  cm⁻¹/atm, g⁰_He=0.02113(1)\gamma^{0}_{\mathrm{He}}=0.02113(1)  cm⁻¹/atm, g⁰_O2=0.03978(6)\gamma^{0}_{\mathrm{O}_{2}}=0.03978(6)  cm⁻¹/atm) is presented covering pressures of up to 1 MPa. The results are compared to previously available low-pressure data.     

Cavity enhanced absorption spectroscopy measurements of?pressure-induced broadening and shift coefficients in?the?υ1+υ3 combination band of ammonia

Cavity enhanced absorption spectroscopy is performed using an external cavity diode laser operating around 1516 nm. We demonstrate a sensitivity of 6×10⁻⁸ cm⁻¹ Hz^−1/2 and utilise a simple method to measure pressure-induced broadening and shift coefficients. The broadening and shift coefficients for six gases (helium, neon, argon, xenon, oxygen and nitrogen) have been determined at room temperature for four transitions in the υ ₁+υ ₃ combination band of ammonia. Comparisons of the broadening coefficients with previous work in this region, where it exists, show good agreement. The broadening and shift coefficients of nitrogen and oxygen are also in good agreement with calculated values using the Robert and Bonamy theory. Both the broadening and shift coefficients show a clear trend through the rare gases, which can be explained in terms of the varying magnitude of the long range attractive forces operating between the colliding partners. We also demonstrate the application of the Parmenter–Seaver formalism to estimate the potential well depth of the ammonia dimer from the obtained broadening coefficients. The obtained well depth agrees well with theoretical calculations.     

Signal processing system in cavity enhanced spectroscopy

The paper presents a signal processing system used for nitrogen dioxide detection employing cavity enhanced absorption spectroscopy. In this system, the absorbing gas concentration is determined by the measurement of a decay time of a light pulse trapped in a cavity. The setup includes a resonance optical cavity, which was equipped with spherical and high reflectance mirrors, the pulsed diode laser (414 nm) and electronic signal processing system. In order to ensure registration of low-level signals and accurate decay time measurements, special preamplifier and digital signal processing circuit were developed. Theoretical analyses of main parameters of optical cavity and signal processing system were presented and especially signal-to-noise ratio was taken into consideration. Furthermore, investigation of S/N signal processing system and influence of preamplifier feedback resistance on the useful signal distortion were described. The aim of the experiment was to study potential application of cavity enhanced absorption spectroscopy for construction of fully optoelectronic NO₂ sensor which could replace, e.g., commonly used chemical detectors. Thanks to the developed signal processing system, detection limit of NO₂ sensor reaches the value of 0.2 ppb (absorption coefficient equivalent = 2.8 × 10⁻⁹ cm⁻¹).     

Fiber laser intracavity absorption spectroscopy for in situ multicomponent gas analysis in the atmosphere and combustion environments

Intracavity absorption spectroscopy with a broadband Er³⁺-doped fiber laser is applied for the measurements of several molecular species revealing quantitative information about the gas concentration, temperature and chemical reactions in flames. The spectral range of measurements extends from 6200 cm⁻¹ to 6550 cm⁻¹ with the proper choice of the fiber length and by moving an intracavity lens. With a pulsed laser applied in this experiment, the sensitivity to absorption corresponds to an effective absorption path length of 3 km assuming the cavity is completely filled with the sample. For a cw laser, the effective absorption path length is estimated to be 50 km. Absorption spectra of various molecules such as CO₂, CO, H₂O, H₂S, C₂H₂ and OH were recorded separately in the cell and/or in low-pressure methane and propane flames. The presented measurements demonstrate simultaneous in situ detection of three molecular products of chemical reactions at different flame locations. Variation of the relative strengths of OH absorption lines with the temperature enables the estimation of the local flame temperature. The sensitivity of this laser does not depend on the broadband cavity losses and it can be used for in situ measurements of absorption spectra in hostile environments such as contaminated samples, flames or combustion engines. The presented technique can be applied for various diagnostic purposes, such as in environmental, combustion and plasma research, in medicine and in the determination of stable isotope ratios.     

Structure and NLO property relationship in a novel chalcone co-crystal

Single crystals of a chalcone co-crystal (C₁₈H₁₉NO₄/C₁₇H₁₆NO₃Br; 0.972/0.028) have been grown by slow evaporation from solution. The powder second harmonic generation (SHG) efficiency of this chalcone co-crystal is 7 times that of urea. The dependence of second harmonic (SH) intensity on particle size revealed the existence of phase matching direction in this crystal. The large SHG efficiency observed is mainly due to the unidirectional alignment of molecular dipoles, in which the dipole moment of each molecule adds to establish a net polarization. The weak N–H⋅⋅⋅O hydrogen-bond interactions help to stabilize the noncentrosymmetric crystal packing and also contribute partly to the SHG. The better thermal stability, transparency and high laser damage resistance (>1.5 GW cm⁻² at 532 nm, 8 ns) of this chalcone co-crystal indicate that it is a promising material for frequency doubling of diode lasers down to 470 nm. This molecule also shows a third-order NLO response and good optical limiting property of 8 ns laser pulses at 532 nm. The mechanism for optical limiting in this chalcone was attributed to two-photon induced excited state absorption that leads to reverse saturable absorption. The structure–property relationship in this chalcone and related compounds is discussed based on the experimental results and semiempherical hyperpolarizability calculations.     

Measurements of the 3ν 3 band of 14N15N16O and 15N14N16O using continuous-wave cavity ring-down spectroscopy

The absorption spectra of the 3ν₃ band of nitrous oxide isotopologues, ¹⁴N¹⁵N¹⁶O and ¹⁵N¹⁴N¹⁶O, have been measured using diode laser cavity ring-down spectroscopy in 6400–6463 and 6465–6532 cm^-1, respectively. Spectroscopic parameters and the rotational line intensities of the bands have been determined. We have applied this spectroscopic technique to the measurements of the absolute isotope ratio of those isotopologues using the absolute line intensities. PACS 32.10.Bi; 33.20.Vq; 33.70.-w; 42.55.Px; 42.62.Fi     

Diode laser spectroscopy of H2O and CO2 in the 1.877-μm region for the in situ monitoring of the Martian atmosphere

A diode laser spectrometer was used in the laboratory to study H₂O and CO₂ line intensities and self-broadening coefficients around 1.877 μm. The spectral region ranging from 5327 cm^-1 to 5329 cm^-1, which is suitable for the in situ sensing of water vapor and carbon dioxide in the Martian atmosphere, was studied using a distributed feedback GaInSb diode laser from Nanoplus GmbH. We have studied one line from the (011)←(000)band of H₂O and two lines from the (01¹2)_I←(000) band of CO₂. The results of intensity and self-broadening measurements are compared to available databases, ab initio calculations and previous experimental determinations. Finally, we discuss the current development of the tunable diode laser absorption spectrometer instrument, a laser diode sensor devoted to the in situ measurement of H₂O and CO₂ in the Martian atmosphere. PACS 07.57.Ty; 07.87.+v     

Absorption line strengths of <Superscript>15</Superscript>NH<Subscript>3</Subscript> in the near infrared spectral region

We present initial results of an investigation of the near infrared absorption spectrum of ¹⁵NH₃ between 6468 and 6692 cm⁻¹. A widely tunable external cavity diode laser is used in a direct absorption setup to determine the line positions and line strengths of several lines in that spectral range. Line data measurements on a ¹⁴NH₃ sample are used for validation of the setup by comparison of the results with available literature data. The presented overview measurements on absorption lines of ¹⁵NH₃ have been performed to serve as a starting point for candidate line selection for prospective isotopic ratio measurements of ¹⁴NH₃ and ¹⁵NH₃.     

Mid-infrared laser absorption spectrometers based upon all-diode laser difference frequency generation and a room temperature quantum cascade laser for the detection of CO, N2O and NO

We describe the performance of two mid-infrared laser spectrometers for carbon monoxide, nitrous oxide and nitric oxide detection. The first spectrometer for CO and N₂O detection around 2203 cm^-1 is based upon all-diode laser difference frequency generation (DFG) in a quasi-phase matched periodically-poled lithium niobate (PPLN) crystal using two continuous-wave room-temperature distributed feedback diode lasers at 859 and 1059 nm. We also report on the performance of a mid-infrared spectrometer for NO detection at ∼ 1900 cm^-1 based upon a thermoelectrically-cooled continuous-wave distributed feedback quantum cascade laser (QCL). Both spectrometers had a single-pass optical cell and a thermoelectrically cooled HgCdZnTe photovoltaic detector. Typical minimum detection limits of 2.8 ppmv for CO, 0.6 ppmv for N₂O and 2.7 ppmv for NO have been demonstrated for a 100 averaged spectra acquired within 1.25 s and a cell base length of 21 cm at ∼ 100 Torr. Noise-equivalent absorptions of 10^-5 and 10^-4 Hz^-1/2 are typically demonstrated for the QCL and the DFG based spectrometers, respectively. PACS  42.55.Px; 42.62.Fi; 42.65.-k; 42.72.Ai; 42.68.Ca